Mechanical Engineering Commons^™

The Steady-State Response Of A Fluid-Filled Beam Near Resonance, Niranjan Jayantibhai Patel

Masters Theses

"In this report the steady-state near-resonant vibration of a hollow fluid-filled beam is considered. The energy dissipation caused by the beam-fluid interaction is approximated by introducing a viscous damping force into the Bernoulli-Euler beam equation. A theoretical expression is developed for the displacement of the hollow beam by solving this modified Bernoulli-Euler beam equation. Tests are made using a cantilevered fluid-filled box to simulate a unit of beam-fluid length. The band-width technique is used to determine the incremental viscous damping coefficient from test data. A variety of fluids are used in the box to determine the effect of the fluid …

Wind Tunnel Modeling Of The Atmospheric Boundary Layer, Sreemanth Pagadala

Masters Theses

"The importance of simulating atmospheric flows in wind tunnels has been well established. Experiments were conducted in the Modified Aerodynamic Wind Tunnel to determine the suitability of this wind tunnel for simulating atmospheric flows and the degree to which various aspects of modeling could be fulfilled. A temperature profile to simulate the inversion aloft was generated inside the test section, and then an appropriate velocity profile was built in by means of screen mesh arrangements. The turbulence characteristics of the flow were measured. The validity of the temperature, velocity and turbulence fields were examined. It was found that while the …

Investigation Of A New Type Of Cloud Condensation Nuclei Counter: The Thermal Quench Chamber, Donald Arthur Hess

Masters Theses

"The design and development of a new type of cloud condensation nuclei counter was undertaken to provide a new laboratory and field instrument that operates on a different theoretical basis than the thermal diffusion chamber now being used by meteorologists and other scientists. In the new instrument the test aerosol is pumped through a tube where it is first humidified and then cooled at constant pressure to create a supersaturation, causing water vapor to condense upon the nuclei in the aerosol sample. The concentration of cloud condensation nuclei is then determined by counting the water drops. The control of temperature …

Transient Cooling Of A Sphere Due To Boiling, Salil K. Banerjee

Masters Theses

"The time - dependent surface temperature is determined for a sphere subjected to cooling by boiling. One dimensional heat transfer is considered and the solid is assumed to be homogeneous, isotropic and opaque to thermal radiation and to have temperature independent physical properties. The initial temperature of the sphere and the coolant are assumed to be uniform and arbitrary. The boiling heat transfer coefficient at the surface of a sphere is a strong function of the surface temperature thus resulting in an extremely nonlinear transient heat conduction problem. As a practical application of the problem, the process of quenching has …

A Practical Approach To The Exhaust Silencing Of A Pneumatic Rock Drill, Morton Gary Barth

Masters Theses

"One-third octave spectrum analyses of the exhaust noise produced by a medium sized pneumatic rock drill were obtained during free recriprocation to determine the most troublesome bands of noise. Noise reduction techniques were then used to design exhaust mufflers which would reduce the level of the exhaust noise to an acceptable level with a minimum increase in back pressure. The prototype mufflers evaluated included an expansion chamber, a resonator, and various modified expansion chambers. One of the modified expansion chambers tested provided very good attenuation reducing the exhaust noise from 113 dBA to 87 dBA at the operator's ear position. …

Application Of Transmission Matrices To Describe Transverse Vibrations Of Non-Uniform Bernoulli-Euler Beams, Dean Irle Parker

Masters Theses

"This report investigates the application of transmission Matrices to determine natural frequencies of non-uniform Bernoulli-Euler beams. The classes of non-uniform beams considered includes: truncated wedges, truncated cones, and truncated rectangular pyramids. Two transmission matrices were derived from solutions to the Bernoulli-Euler equation. One was an exact closed form solution which was applicable for the above classes of beams excluding uniform and nearly uniform beams. The second solution was an approximate one limited to the use for nearly uniform beams, but which does give the correct solution to the uniform beam in the limiting case. The transmission matrix has two advantages: …

Drift Velocity Measurements Of Various Materials Floating On Water Waves, Paul Keith Scherrer

Masters Theses

"A study was conducted to determine the affects of deep water gravity waves on oil lenses and surface floats. The experiment was conducted in a wave tank equipped with a mechanical wave generator. The data obtained consisted of the measured velocities of oil lenses and thin plastic floats under the action of a variety of wave conditions. It was found that waves do cause a movement of the oil lenses and surface floats, and their velocity was found to be greater than the surface drift predicted by Stokes' theory of mass transport by waves in a single component fluid. For …

On The Complex Index Of Refraction For Liquids, Juan Guillermo Ochoa Sierra

Masters Theses

"Methods for determining the optical constants, the real and the imaginary part of the complex index of refraction, for weakly and strongly absorbing liquids are reviewed and evaluated. Both reflection and transmission methods were considered and preliminary steps are taken for determining the optical constants for both water and oil in the visible region (0.45 - 0.65 microns) of the spectrum. A low resolution spectrometer was used and the transmission measurements through fuel oil, number 1 through 6, and crude oil were performed. The imaginary part of the complex index of refraction was deduced from the above measurements and appears …

Feasibility Study Of Using A Steam Power System In A Small Garden Tractor, Niranjan Kumar Doshi

Masters Theses

"This thesis is a feasibility study of using a steam power system in a small garden tractor. The relative advantages of steam power are discussed and compared with the characteristics of internal combustion engines. A monotube boiler is designed where steam is generated in stacked tube spirals. The boiler generates 225 lbs/hr of dry saturated steam at 500 psia, which corresponds to an engine output of 20 IHpage A rotary positive displacement engine is employed to expand the steam to 16 psia. A rotor instead of a piston eliminates the conventional connecting rod and crank shaft. The engine developes 15 …

Design And Test An Operational Amplifier Speed Transducer, Tung-Ming Huang

Masters Theses

"This thesis describes the design of an angular speed transducer. The purpose of this device is to provide a D.C. voltage which is proportional to the angular speed of a rotating shaft at any instant. The speed of the shaft is defined from a magnetic pickup monitoring a gear or similar device attached to the end of the shaft of a piece of rotating equipment. The signal from the magnetic pickup is modified and compared to a frequency generated in the feedback loop of the speed transducer and the error is sent to an integral type controller. The output of …

Analysis Of A Substitute For The Impact Damper To Damp Near-Resonant Mechanical Vibrations, Nguyen Khanh Van

Masters Theses

"This report investigates a substitute for the impact damper which, although highly effective in reducing vibration amplitudes of near-resonant mechanical systems, in operation causes often unacceptable intensive noise. The present damper consists of a piston free to move in a cylinder, at either end of which is a ball valve set to open at a preset pressure, and in the middle along its length an intake port. An approximate analytical study is made to determine the conditions for the existence of "noiseless periodic operation" of the damper, periodic operation without the occurence of impacts. This approach is based on the …

Design Of A Torsional Vibration Machine, Prafulchandra Pragjibhai Desai

Masters Theses

"In this thesis the design of the major components of a torsional vibration machine is presented. The machine is a torsional vibration actuator which will deliver a mean output angular velocity with a superimposed harmonic component. This type of motion can be used to study the torsional vibration characteristics of models representing crankshafts, gear trains, torsional dampers, and other systems. The primary machine elements of the actuator are a power source, flywheel, and a Hooke's joint. The power source consists of a D.C. shunt motor and a drive transmission using 3 V-belts. Through the use of a Hooke's joint, approximate …

The Effects Of Intense Sound Levels And Steady Flow On The Propagation Of Plane-Waves In Air, Wuu Hao

Masters Theses

"This thesis is a theoretical investigation of the effects of intense sound levels and steady flow on the propagation of plane-waves in tubes of constant diameter. The analysis is limited to a study of the change of wave profile due to the intense sound levels, and steady flow. However, corrections for effects of viscous and heat conduction losses at tube walls are also presented. To simplify the analysis, the problem is treated by considering the steady flow and finite-amplitude-sound wave effects separately. For finite-amplitude sound only, two approaches are evaluated. The first uses small perturbations to derive a finite-amplitude wave …

Force Analysis Of Involute Spur Gears, Janakkumar Girjashanker Dave

Masters Theses

"This study is devoted to the fundamental action which occurs between spur gears with involute tooth profiles when power is transmitted at a constant angular velocity ratio. Various aspects of the interaction between two mating teeth are considered. Analytic expressions for the variation of the force transmitted between two teeth are derived. Two cases are considered which include and exclude the effects of sliding friction between the teeth. The parametric equations of the involute curves for two mating teeth are derived in terms of body-fixed coordinates. Analytical expressions for Hertz compressive stresses in the teeth were also obtained. The same …

A Study Of Plane Wave Filter Analysis With Flow, Thomas Valle Huber

Masters Theses

"The purpose of this investigation is to determine the effect of slow steady flow on the reflection and transmission characteristics of acoustic filters.

A standing wave tube and transmission tube apparatus, designed and built by a previous investigator, was modified to accept slow steady flow. Reflection characteristics were determined from measurements made on the inlet side of the filters investigated. These data along with measurements taken with the transmission tube apparatus were used to determine transmission characteristics. The calculations were simplified by terminating the filters anechoically. The filters used in this investigation were an expansion chamber, an automobile type muffler …

Design And Construction Of A Drop Generator For Use In A Vertical Wind Tunnel, Danny Ray Conner

Masters Theses

"A drop generator, based on the principle of a vibrating capillary, was designed and built for use in the UMR vertical atmosphere wind tunnel. The drop generator worked very well on a test stand where it was firmly supported, but was not consistent when tested in the wind tunnel. Vibration of the wind tunnel walls and a slight turbulence near the forward edge of the generator caused an oscillation in the position of the stream of drops. The oscillation resulted in some of the drops hitting the edge of the collector cup, where the drops would accumulate until a large …

Laminar Heat Transfer For Small Prandtl Number Fluids Including Step Change In Wall Temperature, Shiny Ting

Masters Theses

"The object of this investigation is to provide a simple means of determining the heat transfer from a flat plate which has an unheated leading length x₀. The case of steady, two-dimensional, laminar flow of an incompressible fluid with a Prandtl number of less than one is considered. Since there exists an unheated length and the Prandtl number of the fluid is less than one, the thermal boundary layer intersects the flow boundary layer. Thus, the solution of the problem divides into two regions. In this study, the problem is solved analytically by employing the energy integral equation. The temperature …

The Influence Of Member Length On Thermal Contact Resistance In A Vacuum Environment, Larry Martin Cooper

Masters Theses

"An investigation was conducted to determine the influence of member length on thermal contact resistance in a vacuum environment. A model was created which consisted of a center rod axially loaded between two other members. It was assumed that circular macroscopic constriction areas were formed at the contact interface when the rods were loaded. Macroscopic modeling of the contact surfaces makes the thermal contact analysis a function of the mechanical and thermal boundary conditions of the total body. The method of finite differences was employed to calculate the temperature distribution, heat flows, and thermal contact resistance of each member. Data …

Design And Preliminary Testing Of A Thermomechanical Rock Fragmentation Apparatus, Gary Earl Fenton

Masters Theses

"The design characteristics of equipment to thermally weaken and mechanically fragment hard rock were developed and the apparatus constructed. An initial investigation of thermo-mechanical fragmentation was conducted on Missouri red granite. The particles from the fragmentation tests were sized and this analysis was used in the Rittinger theory to calculate surface area breakage energy. It was found that the application of thermal energy could reduce the surface area breakage energy per unit volume of material removed by as much as 41 percent. The use of kerfs in the rock increased the amount of material removed and permitted larger particles to …

A Study Of A Nitrogen Heat Pipe, Jay Dudheker

Masters Theses

"An experimental heat pipe, 33.25 inches long and 0.75 inches in diameter, with modacrylic fiber wick and liquid nitrogen as its working fluid was constructed to study the operating characteristics of a cryogenic heat pipe. The effective thermal conductivity and the axial temperature distribution were determined for various levels of power input. The effect of inclination angle on the above parameters was also measured"--Abstract, page ii.

A Triangular Element For Numerical Solutions Of Axisymmetric Conduction Problems In Cylindrical Coordinates, Prafulla Chandra Mahata

Masters Theses

"The triangular element is one of the many suitable elements which are used in finite difference methods as applied to conduction heat transfer. Such elements find many applications in conduction problems in Cartesian coordinates. This work proposes a new triangular element for axisymmetric conduction problems in cylindrical coordinates. The validity and workability of the networks formed by the proposed triangular elements are strengthened by selected examples. The work is completed by the application of the triangular element to an industrial problem having irregular boundaries. The results are compared with the solution obtained by the finite element method"--Abstract, page ii.

An Experimental Determination Of The Effect Of The Axisymmetric Turbulent Wake On The Pressure Distribution On A Sphere, Martin Gardner Bowin

Masters Theses

"A study of the effect of the turbulent wake of a water drop on the motion of a smaller droplet is essential in order to gain an understanding of the behavior associated with the collision coalescence phenomena. The use of spheres of macroscopic size proves to be a valuable method in observing these effects. This experimental investigation centers on (1) a check on the validity of the instrumented sphere as a device to measure normal static pressure, and (2) the study of the effect of the turbulent wake of the test model sphere upon the instrumented sphere. Measurements were made …

The Thermal Contact Resistance Of Lubricant Films In Vacuum, Garry A. Heizer

Masters Theses

"This paper presents the results of an experimental investigation on the thermal contact resistance of lubricant films and bare interfaces. The apparatus and procedure used in the determination of these resistances are described. Twelve series of tests were performed to evaluate the effects of temperature and contact pressure on the thermal resistance of lubricant films. Variations of thermal contact resistance with temperature and contact pressure for four lubricants and for bare interfaces are presented graphically. The thermal resistances of the four lubricants tested in vacuum conditions: lithium grease, graphite grease, molykote grease, and silicone lubricant, were found to lie in …

A Study Of Radiative Heat Transfer From A Spherical Layer, Hakimuddin Kalimuddin Khalil

Masters Theses

"The problem of radiative heat transfer from a spherical layer of absorbing-emitting gas has been studied. First, the medium is assumed to be gray and then nongray. A thorough survey of literature from fields other than heat transfer, such as astrophysics and neutron transport has been made to stimulate further interest in this important area. To gain some insight into the effect of various parameters on the heat transfer, simple physical situations involving isothermal medium are considered. Comparison of the results obtained for the flux from the spherical and planar layers reveal that the curvature becomes increasingly important as the …

Two Component Heat Pipe, Surapol Chandsawangbhuvana

Masters Theses

"A two component heat pipe with water and ethanol as the working fluid was investigated at different angles of inclination and various ethanol concentration for two power loads. The heat pipe was 15 inches long and 0.75 inches in diameter with a 100 mesh stainless steel screen wick. The wall and the vapor temperatures were measured at different stations along the length of the heat pipe by copper-constantan thermocouples. The results were used to evaluate an existing model which includes the constraint of thermodynamic phase equilibrium of the solution on the governing equations. Based on the measured pressure and temperature …

Radiant Interchange In A Non-Isothermal Rectangular Cavity, Tilak Raj Sawheny

Masters Theses

"Radiant interchange between non-isothermal, gray diffuse surfaces with non-uniform radiosity has been determined for a rectangular cavity. Temperature distribution and heat flux as thermal specifications for the parallel surfaces of the cavity have been considered separately. Ambarzumian's method has been used for the first time to solve a radiant interchange problem. According to the method, the integral equation for the radiosity is first transformed into an integro-differential equation and then into a system of ordinary differential equations. Initial conditions required to solve the differential equations are the H-functions. The H-functions represent the radiosity at the edge of the cavity for …

A Step-Wise Gray Approximation Of The Radiative Absorption Coefficient For An Isothermal Hydrogen Plasma, Keith Harlan Browne

Masters Theses

"The radiative absorption coefficient of an isothermal hydrogen plasma is calculated using a step-wise gray approximation. The approximation retains a high degree of accuracy while significantly reducing the numerical computer time. The accuracy of the approximation depends on the spacing of the steps taken in the frequency spectrum as well as the number or steps used; 135 steps are used in this study. Plasma conditions of interest in this study are for temperatures between 5000 and 60,000ºK, densities between 10⁻⁵ and 10⁻⁷ gm/cm³, and thicknesses between 0.1 and 100 cm. Flux and intensity calculations are made for each case using …

Feed Drive Design For Numerically Controlled Machine Tools, Subash Bhatia

Masters Theses

"The various types of feed drive control systems used in numerical control of machine tools have been broadly classified. Further a step by step design has been presented for the feed drive of a numerical contouring control milling machine. The aim has been to develop a consistent strategy for tackling a variety of such problems. Consequently stress has been laid on principles and not on design figures"--Abstract, page ii.

Design Of A Semi-Automatic Transmission, Yogendra Prahladray Buch

Masters Theses

"Design of a semi-automatic four-speed transmission for automotive engines with moderate horsepower is described. The basic configuration consists of main and countershafts and five pairs of constant-mesh gears. Engine torque is transmitted through an input gear pair to the countershaft, and finally to the output shaft through a selected output gear pair. Selection is accomplished by engaging one of five hydraulically operated clutches located on the countershaft. Engagement fixes the desired gear to the countershaft and engine torque is then transmitted to the mating gear, which is fixed to the output shaft. Fourth speed is obtained by coupling the input …

The Effect Of Diameter On The Film Boiling Behavior Of Liquid Nitrogen, William Joseph Wafer

Masters Theses

"A film boiling heat transfer study was conducted for liquid nitrogen at atmospheric pressure. The heat transfer surfaces used were cylinders with outside diameters of 0.450, 0.650, 0.850, and 1.000 inches. The temperature differences covered were from approximately 150ºF to approximately 600ºF. The data indicate that the heat flux will decrease to a minimum then increase slightly as the diameter of the heat transfer element is increased at constant temperature difference. The heat transfer coefficient is expected to approach a flat plate correlation as the diameter approaches infinity"--Abstract, page ii.