Mechanical Engineering Commons^™

Selective Laser Melting 17-4 Ph Stainless Steel And The Effect Of Varied Thermal Treatments On Fatigue Behavior., Sean Daniel Dobson

Electronic Theses and Dissertations

Fatigue failure is the leading source of loss in industry. In order for new means of manufacturing to move towards mainstream use a complete understanding of material and mechanical behavior must be gained. This endeavor seeks to aide in that task by observing the fatigue behavior of selective laser melting (SLM) additive manufacturing (AM) specimens and the effect of differing thermal treatment conditions for an optimized AM process. Stainless steel 17-4 PH specimens were fabricated using SLM AM and thermally treated to three conditions: as-built, solutionized and hardened, and direct hardened. These specimens were characterized for material (powder quality, density, …

Experimental Evaluation Of Heat Leak And Convective Heat Transfer In A Household Freezer., Catherine E. Berghuis

Electronic Theses and Dissertations

Heat leak into household refrigerated cabinets is a key driver affecting energy consumption and efficiency of the cooling system. Additionally, knowledge of heat transfer coefficients of internal surfaces is valuable in the development of cabinet and system level performance simulations. Several studies have examined heat leak of refrigeration units using heat flux sensors (HFS); however, no such studies have used heat flux measurements to derive convective heat transfer coefficients of the refrigerated unit walls. The goal of this study is to evaluate the use of HFS to quantify heat leak into a 490-liter freezer and determine the wall convective heat …

Influences Of Material Extrusion Additive Manufacturing (Meam) Parameters And Additives On Polyvinylidene Fluoride (Pvdf) Properties., Niknam Momenzadeh

Electronic Theses and Dissertations

Beyond the beneficial characteristics of smart polymers associated with all polymers such as flexibility and cost fabrication, smart materials exhibit multifunctional behaviors. The prospect of integrating structural and sensing/actuation capabilities into a single structure gives design engineers an ability to innovate highly novel, multi-functional creations. Polyvinylidene Fluoride (PVDF) is one of the widely used multi-functional materials which offers a variety of desirable material properties. It possesses exceptional chemical and UV resistance, biocompatibility, low processing temperature and affordable price making it a competitive choice for many commercial applications. In addition, among polymers, PVDF is simply the most dominant piezoelectric polymer. On …

Impact Of Magnetocaloric Material Properties On Performance Of A Magnetocaloric Heat Pump., Michael G. Schroeder

Electronic Theses and Dissertations

In the field of magnetocaloric heat pumps much research has been performed around machine design and theoretical machines, but little has been researched around practical problems such as variability in material properties. The present work defines a simulation tool that has been proven with experimental data. Magnetocaloric material cascades were statistically analyzed and parameterized, such that they could be recreated parametrically using a split Lorentz function with normally distributed parameters. Correlated curve-defining values with standard deviations were used as input into the simulation tool to determine the effect of variation on cooling heat pump performance for a household refrigerator application. …

Strain-Based Mechanical Failure Analysis Of Buried Steel Pipeline Subjected To Landslide Displacement Using Finite Element Method, Sean Goodluck Mamuzo Edeki

Electronic Theses and Dissertations

Landslide displacement is one of the major threats to the structural integrity of buried oil and natural gas pipelines that are often located far from major markets with terrains prone to permanent ground deformations. These pipelines can experience large longitudinal strains and circumferential deformation resulting from the differential ground movements thereby potentially impacting pipeline safety by adversely affecting structural capacity and leak tight integrity. In order to proffer theoretical basis for the design, safety evaluation and maintenance of pipelines, the failure analysis and mechanical behavior of buried API X65 steel pipeline perpendicularly crossing landslide area was investigated with the Finite …

Using Computational Fluid Dynamics To Accurately Model Agricultural Spray Nozzles, Zachary Chapman

Electronic Theses and Dissertations

Computational fluid dynamics (CFD) is a tool used by engineers in many industries to study fluid flow. A relatively new industry to adopt the use of CFD is the agricultural industry. The present work seeks to understand whether CFD can be used to accurately model spray nozzles. A spray nozzle commonly used in agricultural spraying was simulated. First, the impact of factors such as mesh size, mesh type, and physics models have on the solution were investigated. Next, a method to pulse the spray was determined. This was required to compare simulation results with experimental data. A user-defined function was …

A Series-Elastic Robot For Back-Pain Rehabilitation, Elhussein Shata

Electronic Theses and Dissertations

Robotics research has been broadly expanding into various fields during the past decades. It is widely spread and best known for solving many technical necessities in different fields. With the rise of the industrial revolution, it upgraded many factories to use industrial robots to prevent the human operator from dangerous and hazardous tasks. The rapid development of application fields and their complexity have inspired researchers in the robotics community to find innovative solutions to meet the new desired requirements of the field. Currently, the creation of new needs outside the traditional industrial robots are demanding robots to attend to the …

Development Of Cellulose Acetate-Based Scaffold For Bone Tissue Engineering Applications, Ruhit Sinha

Electronic Theses and Dissertations

Cellulose Acetate (CA) based biomaterials are being used as substrates for bone ingrowth applications due to their nontoxic and nonirritant nature coupled with optimum morphology and stiffness. Electrospinning with additives and/or post-treatment has emerged as a viable protocol to further improve mechanical properties of CA and expand its utility. Herein, we highlight the role of potassium chloride (KCl) in association with airdrying to enhance the elastic modulus and tensile strengths of CA fibers. Salt aggregation in between fibers is observed through Scanning Electron Microscopy (SEM), however, Fourier-transform infrared (FTIR) analysis signifies the interactions between K+ ions and acetyl groups. The …

Energy Efficiency And Alternative Energy Generation In Existing Buildings On A College Campus, Sameer Keshavan

Electronic Theses and Dissertations

Universities and colleges are looking for ways to be sustainable and save energy costs on their campuses. In terms of raw dollars, “America’s colleges and universities spend almost $7 billion a year in energy and utilities”. Campus buildings consume more than 80% of the energy utilized by the universities and it is often used in the form of electricity for lighting, ventilation, air-conditioning, and natural gas for heating. By reducing energy use, it will translate into cost savings that could be utilized towards student programs, facility improvements, and other university initiatives. This can be achieved by energy conservation efforts and …

Characterization Of Directed Energy Deposition Additively Manufactured Grcop-42 Alloy, Scott Landes

Electronic Theses and Dissertations

GRCop is an alloy family constructed of copper, chromium, and niobium and was developed by NASA for high heat flux applications. The first of its kind, GRCop-84, was specifically designed for the environments seen by channel cooled main combustion chamber liners. To further increase thermal conductivity while maintaining material strength characteristics, the percentage of alloying elements were cut in half and GRCop- 42 was developed. In recent years, NASA has successfully additively manufactured GRCop with comparable material characteristics to wrought GRCop using a Laser Powder Bed Fusion (L-PBF) process. Benefits of this process include fabrication of intricate cooling channels as …

The Effects And Analysis Of Implant Type And Surgical Approach In Total Hip Arthroplasty Dislocation Resistance, Brittany Marshall

Electronic Theses and Dissertations

Total hip arthroplasty (THA) is one of the most successful orthopaedic surgeries performed, in which the hip joint is reconstructed to decrease pain and to improve the functionality to the joint. Although these surgeries are very successful, there still remain areas for improvement, such as failures due to instability and dislocation of the implanted joint. The purpose of this thesis is to investigate the effect of surgical entrance approach on dislocation, the effect of implant type, and the effect of capsule repair and closure. The need to quantify the resistance to dislocation is important in understanding the effect that each …

Computational Modeling Of Shock Wave Propagation In A Layered Composites, Nicholas Ryan Scott

Electronic Theses and Dissertations

Modeling and simulation of a metallic flyer plate impacting a woven glass-fiber reinforced plastic (GRP) plate at different velocities was performed using the ALE3D© finite element code. The one-dimensional strain-based shock wave propagation experimental data in terms of time history of GRP’s back surface material particle velocity, available in open literature [1], were utilized in the calibration of a continuum damage mechanics (CDM) model. The experimental data included D7 Tool Steel and 7075-T6 aluminum flyer plates and two different GRP thicknesses (6.8 mm or 13.6 mm) with varying impact velocities in the range of about 8.5 m/s to 418 m/s. …

In Vivo Data Capture Using Hssr For Calibration Of Computational Models, Thor Erik Andreassen

Electronic Theses and Dissertations

Computational modeling is a vital tool for understanding and evaluating healthy and unhealthy function of the musculoskeletal aspects of the human body. However, the accuracy of the musculoskeletal models depends significantly on the accuracy of the input data used to calibrate various behavioral parameters of the model. To date, most computational models have been built using generic in vitro data, mostly because of a lack of accurate and meaningful datasets from in vivo testing. The next major step in computational modeling is to create subject-specific computational models using calibration data taken from in vivo testing. The overall goal was to …

Particle Injection Simulation On Cold Spray Technology, Christopher A. Santini

Electronic Theses and Dissertations

Computational Fluid Dynamics (CFD) is a useful tool when it comes to research in the fields of Aerodynamics, Turbomachinery, and is used in several other fields of research. CFD is an important tool in the engineering industry because it allows for understanding and evaluation of a new design, this can lead to advancements in developing a more efficient and effective design. This tool helps in the understanding of the flow phenomena and how it can interact with its surroundings. One of the main reasons in the use of CFD is to reduce the cost of testing a design by running …

Effects On Initial Fixation Of Cementless Tibial Trays In Total Knee Arthroplasty, Brooke Fritts Thompson

Electronic Theses and Dissertations

Bone mineral density (BMD), among other factors, largely effect the initial stability of the cementless tibial tray component in a total knee replacement (TKR), where increased motion at the tray-bone interface hinders bony ingrowth. With a lack of bony ingrowth, the cementless implant will not experience long-term success. Understanding which factors influence initial stability yields insight into surgical technique considerations and help inform a surgeon’s implant choice. The objective of this study was to evaluate factors influencing the initial stability of cementless tibial trays using a 6-degree of freedom (6-DOF) robotic joint simulator, the AMTI VIVO, and combined loading scenarios …

Ultrasonic-Based Condition Assessment Of Wooden Utility Poles, Yishi Lee

Electronic Theses and Dissertations

More than 300 million utility poles shoulder the utility grid in the United States. However, the ineffectiveness of the current inspection process causes roughly a third of utility poles removed from the service deemed suitable for reuse. Due to the utterly essential role of the power infrastructure, budget shrinkage, and the structural degradation of the modern distribution grid, this Ph.D. dissertation addresses the challenges by proposing a physics-based signal analysis method with a jointly developed ultrasonic UB1000 system c to enhance the objectivity in ultrasonic-based nondestructive evaluation (NDE). The proposed methodology has been deployed commercially in the field and featured …

Development And Characterization Of A Biopolymer Direct-Write Process For 3d Microvascular Structures Formation., Xiaoming Fan

Electronic Theses and Dissertations

Engineering of bulk tissues has been limited by the lack of nutrient and waste exchange in these tissues without an adjacent capillary network. To produce microvasculature, a scaffold must be produced that provides temporary mechanical support and stimulate endothelial cell adhesion, growth, and morphogenesis into a vessel. However, current well-established techniques for producing microvasculature, such as electrospinning, are limited since they lack both the precision to control fiber placement in three-dimensional space and the ability to create fiber networks with predefined diameters to replicate the physiological microvascular progression from arteriole to capillary to venule. Our group has developed a “Direct-write” …

All Season Heat Pipe System., Adrienne Marie Parsons

Electronic Theses and Dissertations

Our energy choices impact the earth’s natural systems and climate. As this becomes increasingly important, the need for decreasing our energy usage is essential. Conventional passive solar systems can significantly reduce the heating load. Similarly, passive ambient energy systems, such as ventilation and sky radiation, can reduce cooling loads. However, the integration of passive heating and cooling systems in the same building and the benefits of actively controlling these otherwise passive systems to maximize annual energy savings has largely been unexplored. This study first evaluates the building cooling capacity of sky radiation, which was previously identified to have the greatest …

Improving Flow-Induced Hemolysis Prediction Models., Mohammad Mohaghegh Faghih

Electronic Theses and Dissertations

Partial or complete failure of red blood cell membrane, also known as hemolysis, is a persistent issue with almost all blood contacting devices. Many experimental and theoretical contributions over the last few decades have increased insight into the mechanisms of mechanical hemolysis in both laminar and turbulent flow regimes, with the ultimate goal of developing a comprehensive, mechanistic and universal hemolysis prediction model. My research is broadly divided into two sections: theoretical/analytical/Computational Fluid Dynamics (CFD) analyses and experimental tests. The first part of my research revolved entirely around analyzing the simplest and most popular hemolysis model, commonly called as the …

Fluid Flow Analysis Of Diluted Evaporating American Whiskey Droplets., Martin J. Brown Vi

Electronic Theses and Dissertations

The recent discovery of the unique structures, whiskey webs, formed when the evaporation of diluted American whiskey, has raised many questions as to the nature of the structures. Their formation process follows as such: (1) dilution of the whiskey to form nanoaggregates, (2) formation of a monolayer at the air-liquid interface, (3) chaotic ethanol evaporation caused monolayer collapse (via dynamic pressure), (4) bulk fluid evaporation caused monolayer collapse (via reduction of surface area), where the web-like structures reside on the surface, and finally, (5) web-like structures deposit on the substrate. The webs imaged via SEM had a striking resemblance to …

Development Of A Single Sensor Approach For Capturing Three-Dimensional, Time Resolved Flame And Velocity Information, Jonathan Reyes

Electronic Theses and Dissertations

Performing non-intrusive measurements is the key to acquiring accurate information representative of what is being observed. The act of measuring often changes the environment being observed altering the information that is being obtained. Due to this, the community of fluid scientists have gravitated towards using laser-based measurements to observe the phenomena occurring in their experiments. The study of fluids has advanced since this point, utilizing techniques such as planar laser induced florescence (PLIF), particle image velocimetry (PIV), laser doppler velocimetry (LDV), particle doppler anemometry (PDA), etc. to acquire chemical species information and velocity information. These techniques, though, are inherently two-dimensional …

Decentralized Consensus-Based Control Allocation For Some Dynamical Systems, August Mark

Electronic Theses and Dissertations

In this dissertation, three separate studies, wherein techniques from graph theory and consensus control are used to address control allocation problems, are presented. In the first study, a decentralized allocator is presented for synthetic jet actuators and control surfaces onboard a small unmanned aerial vehicle to cooperatively generate desired aerodynamic moments. First order linear dynamics are assumed for both the synthetic jet actuators and control surfaces. A weighted consensus algorithm with limited feedback is used for the aerodynamic moment contribution allocator considering constraints. In the second study, the same allocation problem as in the first study is considered, but the …

Mechanical Properties Of Brittle Ceramics: Case Study Of Boron Rich Ceramics And Acropora Cervicornis Coral Skeleton, Alejandro Carrasco-Pena

Electronic Theses and Dissertations

Ceramics are ubiquitous in man-made and natural structures. Their mechanical properties highly depend on their composition, microstructure and level of defects in the bulk of the material, the latter affecting the integrity of the components; such is the case of boron-rich ceramics where large agglomerates create high stressed regions, or coral skeleton where porosity determines their strength against hydrodynamic forces present in the ocean tides. Therefore, studying the properties of ceramic materials using invasive and non-invasive methods helps in the understanding of the link between the properties and the performance of the structures. The aim of this research was to …

Variable Fluid Flow Regimes Alter Endothelial Adherens Junctions And Tight Junctions, Dilshan Ranadewa

Electronic Theses and Dissertations

Variable blood flow regimes influence a range of cellular properties ranging from cell orientation, shape, and permeability: all of which are dependent on endothelial cell-cell junctions. In fact, cell-cell junctions have shown to be an integral part of vascular homeostasis through the endothelium by allowing intercellular signaling and passage control through tight junctions (TJs), adherens junctions (AJs), and gap junctions (GJs). It was our objective to determine the structural response of both AJs and TJs under steady and oscillatory flow. Human brain microvascular endothelial cells (HBMECs) were cultured in a parallel plate flow chamber and exposed to separate trails of …

Dynamic Behavior And Performance Of Different Types Of Multi-Effect Desalination Plants, Mohamed Abdelkareem

Electronic Theses and Dissertations

Water and energy are two of the most vital resources for the socio-economic development and sustenance of humanity on earth. Desalination of seawater has been practiced for some decades and is a well-established means of water supply. However, this process consumes large amounts of energy and the global energy supply is also faced with some challenges. In this research, multi-effect desalination (MED) has been selected due to lower cost, lower operating temperature and efficient in terms of primary energy and electricity consumption compared to other thermal desalination systems. The motivation for this research is to address thermo-economics and dynamic behavior …

A Study On Ultrasonic Energy Assisted Metal Processing : Its Correeltion With Microstructure And Properties, And Its Application To Additive Manufacturing., Anagh Deshpande

Electronic Theses and Dissertations

Additive manufacturing or 3d printing is the process of constructing a 3-dimensional object layer-by-layer. This additive approach to manufacturing has enabled fabrication of complex components directly from a computer model (or a CAD model). The process has now matured from its earlier version of being a rapid prototyping tool to a technology that can fabricate service-ready components. Development of low-cost polymer additive manufacturing printers enabled by open source Fused Deposition Modeling (FDM) printers and printers of other technologies like SLA and binder jetting has made polymer additive manufacturing accessible and affordable. But the metal additive manufacturing technologies are still expensive …

Numerical Investigation Of Coalescence-Induced Self-Propelled Behavior Of Droplets On Non-Wetting Surfaces And Wedged Surfaces., Yan Chen

Electronic Theses and Dissertations

When small drops coalesce on a superhydrophobic surface, the merged drop can jump away from the surface due to the surface energy released during the coalescence. This self-propelled behavior has been observed on various superhydrophobic surfaces and has potential applications in areas related to the heat and mass transfer, such as heat exchangers, anti-icing and anti-frost devices, thermal management and water harvesting. The jumping velocity model was obtained based on published experimental data and the balance of various energy terms described in previous studies. However, the self-propelled mechanism is still not fully understood. In this study, the self-propelled droplet phenomenon …

Vibration Reduction Of Mistuned Bladed Disks Via Piezoelectric-Based Resonance Frequency Detuning, Garrett Lopp

Electronic Theses and Dissertations

Recent trends in turbomachinery blade technology have led to increased use of monolithically constructed bladed disks (blisks). Although offering a wealth of performance benefits, this construction removes the blade-attachment interface present in the conventional design, thus unintentionally removing a source of friction-based damping needed to counteract large vibrations during resonance passages. This issue is further exacerbated in the presence of blade mistuning that arises from small imperfections from otherwise identical blades and are unavoidable as they originate from manufacturing tolerances and operational wear over the lifespan of the engine. Mistuning is known to induce vibration localization with large vibration amplitudes …

Lithium Molybdate-Sulfur Battery., Ruchira Ravinath Dharmasena

Electronic Theses and Dissertations

Rechargeable energy storage systems play a vital role in today’s automobile industry with the emergence of electric vehicles (EVs). In order to meet the targets set by the department of energy (DOE), there is an immediate need of new battery chemistries with higher energy density than the current Li- ion technology. Lithium–sulfur (Li–S) batteries have attracted enormous attention in the energy-storage, due to their high specific energy density of 2600 Wh kg^-1 and operational voltage of 2.0 V. Despite the promising electrochemical characteristics, Li-S batteries suffer from serious technical challenges such as dissolution of polysulfides Li₂S_{x …}

Experimental Investigation Of The Manufacture Of Tunable Graphene Oxide Filter Membranes Using Intense Pulse Light, Joshua H Kotter

Electronic Theses and Dissertations

Reduced graphene oxide is a thin, strong, and inexpensive material with a channel and pore structure that make it a promising candidate for a filtration material. Reduced graphene oxide has been produced and tested in the laboratory, but a lack of scalable manufacturing techniques have limited its commercial use.

This thesis has shown that graphene oxide can be rapidly manufactured with an industrially scalable flash reduction process. The flash reduction process uses 0.58 millisecond pulses from a xenon lamp to reduce the graphene oxide film in less than a minute. Results for partially reduced graphene oxide membranes tuned by the …