Mechanical Engineering Commons^™

Electrical Characterization Of Phytoplankton Suspensions Using Impedance Spectroscopy., Margaret R Jett

Electronic Theses and Dissertations

Phytoplankton are closely monitored because of their important environmental role, and the impacts they have on their local ecosystems. Some phytoplankton respond to stress by producing lipids, which can be harvested for biofuels and other chemicals. Microfluidic devices have been important in improving the portability and throughput of phytoplankton characterization methods, increasing their potential for in situ use. This study utilized a small sample of phytoplankton suspended in a stagnant medium and measured the impedance response using a lab-on-chip and impedance analyzer. The individual cell characteristics were derived from the impedance response of the group. The goal was to characterize …

Design For Metal Fused Filament Fabrication (Dfmf3) Of Ti-6al-4v Alloy., Mohammad Qasim Shaikh

Electronic Theses and Dissertations

Additive manufacturing (AM) offers unmatchable freedom of design with the ability to manufacture parts from a wide range of materials. The technology of producing three-dimensional parts by adding material layer-by-layer has become relevant in several areas for numerous industries not only for building visual and functional prototypes but also for small and medium series production. Among others, while metal AM technologies have been established as production method, their adoption has been limited by expensive equipment, anisotropy in part properties and safety concerns related to working with loose reactive metal powder. To address this challenge, the dissertation aims at developing the …

Simulation Of Fracture Strength Improvements Of A Human Proximal Femur Using Finite Element Analysis., Waleed Ebraheem Alim

Electronic Theses and Dissertations

The most common hip fracture in the elderly occurs as a result of a fall to the side with impact over the greater trochanter resulting in a fracture of the proximal femur. The fracture usually involves the femoral neck or the intertrochanteric region. It has recently been determined that the fracture crack of a hip fracture typically initiates on the superior-lateral cortex of the femoral neck and then propagates across the femoral neck, resulting in a complete fracture. The strength of the superior-lateral cortex of the femoral neck is likely determined by the combined properties of the generally thin cortex …

Image Analysis Of Charged Bimodal Colloidal Systems In Microgravity., Adam J. Cecil

Electronic Theses and Dissertations

Colloids are suspensions of two or more phases and have been topics of research for advanced, tunable materials for decades. Stabilization of colloids is typically attributed to thermodynamic mechanisms; however, recent studies have identified transport or entropic mechanisms that can potentially stabilize a thermodynamically unstable colloidal system. In this study, suspensions of silsesquioxane microparticles and zirconia nanoparticles were dispersed in a nitric acid solution and allowed to aggregate for 8-12 days in microgravity aboard the International Space Station. The suspensions were subsequently imaged periodically at 2.5x magnification. Due to the inadequacy of existing image analysis programs, the python package “Colloidspy” …

Design Of Lower Legs Of Mithra, A High-Performance Backdrivable Humanoid Robot, Drake Taylor

Electronic Theses and Dissertations

This thesis presents the design of the knee and ankle of Mithra, a new humanoid robot that aims to be an energy-efficient and highly agile machine. Mithra makes use of new optimization metrics for legged robots to develop a system capable of mimicking human movement. A series of low-impedance, high-torque actuator systems were developed with the goal of creating lightweight, powerful, and robust motion. The structure of Mithra's legs mimics the human structure in leg segment length and weight proportions. Detailed design and analysis were conducted in order to allow Mithra to be a robust and maintainable system. Mithra will …

Material Analysis Of 3d Welded 5356 Aluminum Alloy, Ryan Fouts

Electronic Theses and Dissertations

Metal 3D printing has been reserved for aerospace and high-end automotive industries because of its cost. A gas metal arc welder (GMAW) on a rugged 3D printer frame could make metal additive manufacturing an option for more industries and consumers. 3D welded aluminum has not been examined in depth as an option for additive manufacturing (AM). Extensive tests are necessary to determine the correct settings to use a metal inert gas (MIG) welder for AM. Porosity within the welded material must be evaluated to better understand the additive process. The material properties of 3D welded aluminum will be tested and …

Monitoring Of Overhead Polymer Core Composite Conductors Under Excessive Mechanical Loads Using Fiber Bragg Grating Sensors, Daniel H. Waters

Electronic Theses and Dissertations

This combined experimental and numerical study addresses mechanical effects associated with static and dynamic loading of novel High Temperature Low Sag (HTLS) transmission line polymer core composite conductors. The developed methodology was successfully applied to ACCC® to explain the complex failure mechanisms associated with combined bending and tension loading. Furthermore, the use of Fiber Bragg Grating (FBG) sensors was investigated for the first time to monitor the ACCC® design during installation and in-service.

Transverse low-velocity impacts to the ACCC® conductor having either free or constrained end conditions and large axial tensile loads were performed. It was identified that the most …

Human-Robot Collaboration Enabled By Real-Time Vision Tracking, Travis Deegan

Electronic Theses and Dissertations

The number of robotic systems in the world is growing rapidly. However, most industrial robots are isolated in caged environments for the safety of users. There is an urgent need for human-in-the-loop collaborative robotic systems since robots are very good at performing precise and repetitive tasks but lack the cognitive ability and soft skills of humans. To fill this need, a key challenge is how to enable a robot to interpret its human co-worker’s motion and intention. This research addresses this challenge by developing a collaborative human-robot interface via innovations in computer vision, robotics, and system integration techniques. Specifically, this …

Rational Design Of Advanced Functional Materials For Electrochemical Devices, Shun Lu

Electronic Theses and Dissertations

In recent years, there has been a fast-growing trend in developing urea (CO(NH2)2) as a substitute H2 carrier in energy conversion due to its high energy density, nontoxicity, stability, and nonflammability. Urea, a byproduct in the metabolism of proteins and a frequent contaminant in wastewater, is an abundant compound that has demonstrated favorable characteristics as a hydrogen-rich fuel source with 6.7 wt % gravimetric hydrogen content. Also, there is 2-2.5 wt % urea from mammal urine; therefore, 0.5 million ton of additional fuels will be produced per year just from human urine (240 million ton each year). Electrochemical oxidation has …

Biomechanical Investigation Of Plant Vascular Tissue For Bio-Inspired Design And Flexible Composites, Mukesh Roy

Electronic Theses and Dissertations

Since the inception of evolution, nature has continuously optimized all the natural materials. These optimizations are so efficient that scientists and engineers have started taking inspiration from nature. Such inspiration-based solutions provide sustainable development of new materials with enhanced structural properties and functionalities (such as stiffness, stability, toughness, self-healing etc.). This variety of properties and functionalities is mainly due to the hierarchical organization of such components. Abstraction of the hidden cues of the hierarchical organization, principles and underlying structure-function relations are some of the critical approaches of bioinspired materials design. Inspiration from animals and plants has helped develop the design …

Development Of A High Strength Composite Material Using Large Scale 3d Printing Applications Using Waste Plastic And Steel, Naga Sri Madhavareddy

Electronic Theses and Dissertations

This project focuses on developing a high strength composite material for largescale 3D printing applications using recycled materials like High-Density Polyethylene (HDPE) and Steel 430. This material has applications for in-space manufacturing (the Moon or Mars) as well as large-scale manufacturing on earth. In addition to creating a strong useful material, materials that are easily recycled, but are often not recycled, are used. Recycling plastic and metal reduces pollution, saves resources, reduces waste going to landfills, and prevents the destruction of habitats from the polymerization of new plastic and similarly mining new ore. The percentage of HDPE generated from recycled …

Effect Of Surface Roughness And External Loading On Embedment In Steel And Aluminum Bolted Joints, Nathan Stang

Electronic Theses and Dissertations

Embedment in bolted joints is defined as the local deformation of surfaces into one another due to uneven contact. Embedment that occurs after the tightening of a bolted joint can cause loss of preload in the joint potentially leading to failure. VDI 2230, a German standard for bolted joint design, is currently the main source for engineers regarding embedment. It related expected embedment to the surface roughness in steel bolted joints. This research expands on the VDI standard by performing tests on a commonly used aluminum alloy and a steel alloy. Both cold rolled 1045 steel and 6061- T6511 aluminum …

Effect Of Composition And Print Orientation On Thermal Conductivity Of 3d Printed Composites, Cory Jacques

Electronic Theses and Dissertations

Additive manufacturing (AM) technologies have become widely used for rapid prototyping and are beginning to be used for end-use applications. Fused Deposition Modeling (FDM) is a type of 3D printing where molten thermoplastic is extruded layer by layer to create parts. There is an increasing need for improvement and diversification of material properties to further extend the use of AM parts. AM parts have not been commonly used in heat transfer applications due to the limited availability of information on thermal conductivity of materials and the effects of printing orientation. A special apparatus was designed and built to experimentally test …

Convective Heat Transfer Enhancement Of A Channel-Flow Using Horizontally-Oriented Piezoelectric Fans, Janak Tiwari

Electronic Theses and Dissertations

Experimental and numerical studies were carried out to investigate the convection heat transfer enhancement of air channel flow using a piezoelectric fan, operated at 90.3 Hz. Its peak-to-peak displacement was increased up to 11.8 mm. The average velocity of channel flow was ranged up to 3 m/s, covering both laminar and turbulent flow regimes. The effects of fan location on the heat transfer performance were evaluated by changing the relative position of the fan tip to the heated surface. A maximum heat transfer enhancement of 102 % was obtained at the channel flow rate of 15 LPM. The fan was …

Resonant Ultrasound Spectroscopy: Sensitivity Analysis For Anisotropic Materials With Hexagonal Symmetry, Christopher Lee Sevigney

Electronic Theses and Dissertations

Resonance ultrasound spectroscopy (RUS) is an experimental method by which material properties are obtained by careful observation of the resonant vibrations of a meticulously crafted sample. Among the most common applications of this technique is the determination of single-crystal elasticity. Previous works have considered the reliability of elasticity information obtained via the RUS method when the material is of isotropic or cubic symmetry, and this work extends these efforts to materials with hexagonal symmetry, such as titanium di-boride. The reliability of elasticity information obtained by RUS is evaluated by Sobol Analysis and by close examination of the stiffness-frequency functionality. Findings …

Convective Heat Transfer Enhancement Of A Channel-Flow Using Synthetic Jet, Pravesh Pokharel

Electronic Theses and Dissertations

A transient numerical simulation was carried out using ANSYS Fluent, to investigate the convection heat transfer enhancement of the air channel flow using the synthetic jet. Keeping the dimensional parameters of the domain fixed, averaged channel flow velocity was varied up to 3m/s. The diaphragm displacement effect on synthetic jet was studied, ranging the peak-to-peak displacement value from 0.4 to 1.2mm with increment of 0.4mm. Three locations were studied to determine the best operating location of the synthetic jet. Also, frequencies were varied up to 200Hz with every 50Hz increment, from initial condition of 50Hz. It was found that the …

Development Of Triangular And Tetrahedral Finite Elements For Solutions To Thermoelastic Instabilities Using Hotspotter, Cortney Samuel Leneave

Electronic Theses and Dissertations

The objective of the work presented in this thesis is to develop first-order triangular and tetrahedral elements for solutions to Thermoelastic Instabilities (TEI) regarding sliding friction systems in Hotspotter.

Hotspotter software uses a finite element method and an eigenvalue method and is an important tool because currently no other commercial software exists which solves the TEI problem for critical velocities and wave numbers of a system. Hotspotter currently uses quadrilateral and hexahedral elements for two and three dimensional analysis, respectively. Typically, tri and tet elements are used in industry when doing static and dynamic stress analysis. Therefore, the Hotspotter user …

Nonreciprocity Applications In Acoustics And Microfluidic Systems, Masoud Naghdi

Electronic Theses and Dissertations

Breaking reciprocity in linear acoustic systems and designing a novel actuator for the nonreciprocal valveless pumps are studied in this dissertation. The first part was started by deriving the acoustic governing equations in a moving wave propagation medium. It was shown thatthe Coriolis acceleration term appears ina cross-product term with the wave vector. It means the main reason for breaking reciprocity in the circular fluid flow is the Coriolis acceleration term. Finally, the governing equations were solved numerically by COMSOL Multiphysics software. Moreover, Green`s second identity was used as a complimentary method to prove breaking reciprocityin such a system with …

Tibial Strains And Tray-Bone Micromotions After Total Knee Arthroplasty: Computational Studies Evaluating The Tibial Fixation, Huizhou Yang

Electronic Theses and Dissertations

Cemented and cementless fixation in total knee arthroplasty (TKA) have been successfully used for decades. As the number of younger and more active patients treated with TKA continues to increase, long-term implant survivorship is of increasing importance. One of the most common complications and hence the reason for revision is mechanical loosening (23.1% of all revised TKA). The loosening mechanisms have been proposed for different fixation types. For cemented fixation, bone remodeling after surgery is regulated by the changes in strain energy density (SED). The recruitment of osteoclasts and osteoblasts is controlled by SED-related signals. Insufficient stimuli can promote bone …

Assessing The Effectiveness Of Cfd To Solve An Inverse Problem Of Thermal Profiles For The Protodune-Sp Neutrino Detector, Cecilia Anne Streff

Electronic Theses and Dissertations

Computational fluid dynamics (CFD) is a branch of fluid mechanics which is employed to numerically solve complex fluid, heat transfer, and multiphysics problems. Traditionally, CFD techniques are used to solve “forward” problems—using some known information of a system as inputs to a representative model to predict experimental measurements or expected system behavior. The work presented here demonstrates how CFD may be used to solve an “inverse” problem—given limited experimental data and some model, predict (previously unidentified) “input” system (or system model) parameters. The case study for this research uses a validated CFD modeling approach of the liquid argon (LAr) region …

An Accuracy And Precision Analysis Of The Velys™ Robotic Assisted Solution For Total Knee Arthroplasty, Gary Doan

Electronic Theses and Dissertations

Total knee arthroplasty (TKA) is a procedure where the arthritic surfaces of the knee is removed and replaced with a combination of metal and polymer implants that recreates the joint line to restore function and quality of life. Implant alignment is important in the success of a TKA. Modern day conventional instrumentation can be cumbersome in the operating room and can be inaccurate when resecting bone and aligning implants. Patients with large errors in resections and implant orientation are more prone to experience mechanical failures with their TKA. Mechanical failures in primary TKA require revision surgeries which can lead to …

Broadening The Capability Of Kinetics Analysis In Biomechanics, Nicholas Nelson

Electronic Theses and Dissertations

Two studies are discussed in this manuscript each preceded by a literature review of the topic. The first review and study explore agility movements and the effect that alternative upper designs in shoes might have on ground reaction force measures of performance. The second review and study evaluate methods of predicting ground reaction forces without the use of a force platform. A method of using effective forces and ways of improving its accuracy are evaluated in depth.

Modeling And Analysis For Unit Cell Size, Material Anisotropy And Material Imperfection Effects Of Cellular Structures Fabricated By Powder Bed Fusion Additive Manufacturing., Yan Wu

Electronic Theses and Dissertations

Cellular structures are networks of interconnected struts or walls with porosities and are widely found in many natural load-bearing structures such as plants and bones. Cellular structures offer unique functional characteristics such as high stiffness to weight ratio, tailorable heat transfer coefficient, and enhanced mechanical energy absorption, which makes them highly attractive in various engineering disciplines such as biomedical implants, electrodes, heat exchangers, and lightweight structures. There exists an abundance of literatures that have investigated various mechanical properties of various cellular structures such as Poisson’s ratio, elastic modulus, ultimate strength, yield strength, and failure characteristics. Based on the classic cellular …

Development Of A Pediatric Cardiac Assist Maglev Pump For Use With A Universal Driver System., Landon Heath Tompkins

Electronic Theses and Dissertations

Heart failure (HF) remains the leading cause of death, affecting 26 million adults worldwide and 6.5 million adults in the United States. Pediatric HF patients have been a historically underserved population with few options for mechanical circulatory support (MCS) therapy, a leading treatment as an alternative to heart transplantation. To address this clinical need, the Inspired Universal MagLev System is being developed; a low cost, universal magnetically levitated extracorporeal MCS system with interchangeable single-use pumps that will ultimately provide adult and pediatric patients ventricular and respiratory assist therapies. The Inspired Pediatric VAD is the first single-use pump application for this …

An Investigation Of The Effect Of Contour Process Parameters On The Surface Roughness And Dimensionality Of Overhanging Features In 17-4 Stainless Steel., Katherine Schneidau

Electronic Theses and Dissertations

The relationship between varying contour settings and part geometry provides insight into the attainable surface roughness and dimensional accuracy of parts fabricated in 17-4 stainless steel via selective laser melting (SLM). Varying the contour settings of laser power (W), scan speed (mm/s), and beam offset (mm) for unsupported inclined bars. The utilization of a coordinate measuring machine (CMM) and surface profilometer quantified the dimensional accuracy and average surface roughness (Ra) for upface, downface, and topface surfaces. Adjusting the laser power and scan speed had minimal affect to surface roughness compared to part geometry. Part dimensionality was affected by the …

Aqueous Redox Flow Batteries With Boron Doped Diamond As An Electrode., Alex M. Bates

Electronic Theses and Dissertations

As the interest and implementation of renewable energy accelerates, so does that of grid energy storage. It is widely believed that a cost-effective energy storage technology will bring about the proliferation of renewable energy. Redox flow battery (RFB) technology represents a promising solution to cost-effective grid energy storage. Compared to other technologies, RFBs have a long lifetime, high efficiency, are non-flammable, significantly reduce cost, and separately scale power and energy. The separation of power and energy enables increased energy capacity by simply adding electrolyte volume. Of the challenges facing RFB technology, one readily apparent is the cost of the active …

Dynamic Analysis And Fabrication Of A Bi-Stable Structure Designed For Mems Energy Harvesting Applications., Masoud Derakhshani

Electronic Theses and Dissertations

Thanks to the rapid growth in demand for power in remote locations, scientists’ attention has been drawn to vibration energy harvesting as an alternative to batteries. Over the past ten years, the energy harvesting community has focused on bistable structures as a means of broadening the working frequency range and, by extension, the effective efficiency of vibration-based power scavenging systems. In the current study, a new method is implemented to statically and dynamically analyze a bistable buckled, multi-component coupled structure designed specifically for low-frequency vibration energy harvesting systems in both macro and MEMS-scale sizes. Furthermore, several micro-fabrication steps using advanced …

Methods For Mass Data Acquisition Of Whiskey Webs., Adam D. Carrithers

Electronic Theses and Dissertations

Whiskey webs are a recently discovered phenomenon in which the monolayer collapse during evaporation of diluted American whiskey results in self-assembled, web-like structures. It was found that the pattern of weblike structures were unique between different American whiskey products. It is desirable to use these unique patterns as a “fingerprint” which can be used to identify whiskeys, their chemical constituents, and perhaps even counterfeits. In pursuit of identifying whiskey products based on their web pattern, it is necessary to have a large database of samples imaged for each product. The device discussed herein is the realization of an apparatus capable …

Experimental And Numerical Study Of Process Parameters Effects Towards Part Quality And Porosity During Powder Bed Additive Manufacturing Processes., Subin Shrestha

Electronic Theses and Dissertations

Powder bed additive manufacturing (PB-AM) process utilizes an electron beam or a laser as a heat source to melt the metallic powder particles. These processes have the capability of freeform fabrication, however certain defects such as porosity, high surface roughness, etc. would hinder its application. It is important to understand the effect of the process parameters and the underlying physical phenomena, which lead to the formation of such defects. In this regard, a three-dimensional (3D) thermo-fluid model is developed to study the effect of beam speed on the surface morphology during powder bed electron beam additive fabrication (PB-EBAF). Besides, the …

Materials-Processing Relationships For Metal Fused Filament Fabrication Of Ti-6al-4v Alloy., Paramjot Singh

Electronic Theses and Dissertations

Additive manufacturing (AM) is at the mainstream to cater the needs for rapid tooling and small-scale part production. The metal AM of complex geometries is widely accepted and promoted in the industry. While several metal AM technologies exist and are matured to a level where expectation in terms of design and properties are possible to realize. But the metal AM suffers from the heavy expense to acquire equipment, isotropic property challenges, and potential hazards to work with loose reactive metal powder. With this motivation, the dissertation aims to develop the fundamental aspects to print metal parts with bound Ti-6Al-4V powder …