Mechanical Engineering Commons^™

Tool Sequence Trends In Minimally Invasive Surgery: Statistical Analysis And Implications For Predictive Control Of Multifunction Instruments, Carl A. Nelson, Evan Luxon, Dmitry Oleynikov

Department of Mechanical and Materials Engineering: Faculty Publications

This paper presents an analysis of 67 minimally invasive surgical procedures covering 11 different procedure types to determine patterns of tool use. A new graph-theoretic approach was taken to organize and analyze the data. Through grouping surgeries by type, trends of common tool changes were identified. Using the concept of signal/noise ratio, these trends were found to be statistically strong. The tool-use trends were used to generate tool placement patterns for modular (multi-tool, cartridge-type) surgical tool systems, and the same 67 surgeries were numerically simulated to determine the optimality of these tool arrangements. The results indicate that aggregated tool-use data …

The Impact Of Wire Stent Fabrication Technique On The Performance Of Stent Placement, Shijia Zhao, Xiangyi (Cheryl) Liu, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

Braided wire stents demonstrate distinct characteristics compared to welded ones. In this study, both braided and welded wire stents with the same nominal dimensions were crimped inside a sheath and then deployed into a stenosed artery using finite element analysis. The braided wire stent was generated by overlapping wires to form crisscross shape. A welded wire stent was created by welding the intersection points of wires to avoid sliding between wires. The effect of fabrication technique on mechanical behavior of Nitinol wire stents was evaluated. The results showed that relative sliding between wires reduced the deformation of the braided stent, …

Arterial Wall Mechanics And Clinical Implications After Coronary Stenting: Comparisons Of Three Stent Designs, Linxia Gu, Shijia Zhao, Stacey R. Froemming

Department of Mechanical and Materials Engineering: Faculty Publications

The goal of this work is to quantitatively assess the relationship between the reported restenosis rates and stent induced arterial stress or strain parameters through finite element method. The impact of three stent designs (Palmaz–Schatz stent, Express stent, and Multilink Vision stent) on the arterial stress distributions were characterized. The influences of initial stent deployment location, stent-tissue friction, and plaque properties on the arterial stresses were also investigated. Higher arterial stresses were observed at the proximal end of the plaque. The Multilink–Vision stent induced lesser stress concentrations due to the high stiffness of the Cobalt Chromium material and thinner strut …

In Vivo Demonstration Of Surgical Task Assistance Using Miniature Robots, Jeff A. Hawks, Jacob Kunowski, Stephen R. Platt

Department of Mechanical and Materials Engineering: Faculty Publications

Laparoscopy is beneficial to patients as measured by less painful recovery and an earlier return to functional health compared to conventional open surgery.However, laparoscopy requires the manipulation of long, slender tools from outside the patient’s body. As a result, laparoscopy generally benefits only patients undergoing relatively simple procedures. An innovative approach to laparoscopy uses miniature in vivo robots that fit entirely inside the abdominal cavity. Our previous work demonstrated that a mobile, wireless robot platform can be successfully operated inside the abdominal cavity with different payloads (biopsy, camera, and physiological sensors). We hope that these robots are a step toward …

Analysis Of A Monolithic, Two-Dimensional Array Of Quartz Crystal Microbalances Loaded By Mass Layers With Nonuniform Thickness, Nan Liu, J. S. Yang, Ji Wang

Department of Mechanical and Materials Engineering: Faculty Publications

We study free thickness-shear vibrations of a monolithic, two-dimensional, and periodic array of quartz crystal microbalances loaded by mass layers with gradually varying thickness. A theoretical analysis is performed using Mindlin’s two-dimensional plate equation. It is shown that the problem is mathematically governed by Mathieu’s equation with a spatially varying coefficient. A periodic solution for resonant frequencies and modes is obtained and used to examine the effects of the mass layers. Results show that the vibration may be trapped or untrapped under the mass layers. The trapped modes decay differently in the two in-plane directions of the plate. The mode …

Thickness-Shear And Thickness-Twist Vibrations Of An At-Cut Quartz Mesa Resonator, Huijing He, Jinxi Liu, Jiashi Yang

Department of Mechanical and Materials Engineering: Faculty Publications

We study thickness-shear and thickness-twist vibrations of an AT-cut quartz plate mesa resonator with stepped thickness. The equations of anisotropic elasticity are used with the omission of the small elastic constant c56. An analytical solution is obtained using Fourier series from which the resonant frequencies, mode shapes, and energy trapping are calculated and examined. The solution shows that a mesa resonator exhibits strong energy trapping of thickness-shear and thickness-twist modes, and that the trapping is sensitive to some of the structural parameters of the resonator.

In Vivo Three-Dimensional Blood Velocity Profile Shapes In The Human Common, Internal, And External Carotid Arteries, Alexey Kamenskiy, Yuris A. Dzenis, Jason N. Mactaggart, Anastasia Desyatova, Iraklis I. Pipinos

Department of Mechanical and Materials Engineering: Faculty Publications

Objective: True understanding of carotid bifurcation pathophysiology requires a detailed knowledge of the hemodynamic conditions within the arteries. Data on carotid artery hemodynamics are usually based on simplified, computer-based, or in vitro experimental models, most of which assume that the velocity profiles are axially symmetric away from the carotid bulb. Modeling accuracy and, more importantly, our understanding of the pathophysiology of carotid bifurcation disease could be considerably improved by more precise knowledge of the in vivo flow properties within the human carotid artery. The purpose of this work was to determine the three-dimensional pulsatile velocity profiles of human carotid arteries. …

Numerical Modeling Of Steady Burning Characteristics Of Spherical Ethanol Particles In A Spray Environment, Vaibhav Kumar Sahu, Vasudevan Raghavan, Daniel N. Pope, George Gogos

Department of Mechanical and Materials Engineering: Faculty Publications

A numerical study of steady burning of spherical ethanol particles in a spray environment is presented. A spray environment is modeled as a high temperature oxidizer stream where the major products of combustion such as carbon dioxide and water vapor will be present along with reduced amounts of oxygen and nitrogen. The numerical model, which employs variable thermophysical properties, a global single-step reaction mechanism, and an optically thin radiation model, has been first validated against published experimental results for quasi-steady combustion of spherical ethanol particles. The validated model has been employed to predict the burning behavior of the ethanol particle …

Increased Efficiency Of Low Band Gap Polymer Solar Cells At Elevated Temperature And Its Origins, Bin Yang, James Cox, Yongbo Yuan, Fawen Guo, Jinsong Huang

Department of Mechanical and Materials Engineering: Faculty Publications

Photovoltaic characteristics of a low bandgap polymer, poly[(4,4′-bis(2-lethylhexyl)dithieno-[3,2-b:2′,3′-d]silole)-2,6-diyl-alt-(2,1,3-benzothiadiazole)-4,7-diyl], based bulk hetero-junction organic photovoltaic were investigated from room temperature (RT) to 145 °C to evaluate its applications in harsh environments. The power conversion efficiency was found to increase from 4.1% at RT to 4.5% at 105 °C with increased short circuit current density (J_sc) and fill factor (FF) despite the decreased open circuit voltage (V_oc). Detailed investigation revealed that J_sc and FF improvements were caused by the increased and balanced carrier mobilities at higher temperatures. The V_oc of the low bandgap …

Rehabilitation And Exercise Machine, Judith M. Burnfield, Yu Shu, Adam P. Taylor, Thad W. Buster, Carl Nelson

Department of Mechanical and Materials Engineering: Faculty Publications

An improved rehabilitation and exercise machine is provided which allows a person with physical limitations, disabilities or chronic conditions to use the machine in order to rehabilitate their muscles, improve joint flexibility, and enhance cardiovascular fitness.

Effects Of Mass Layer Dimension On A Finite Quartz Crystal Microbalance, Y. P. Kong, Jinxi Liu, Huijing He, Jiashi Yang

Department of Mechanical and Materials Engineering: Faculty Publications

In this paper, we investigate free thickness-shear and thickness-twist vibrations of a finite crystal resonator of AT-cut quartz carrying a thin mass layer at the central portion of its top surface operating as a quartz crystal microbalance. The equations of anisotropic elasticity are used with the omission of the small elastic constant c56. An analytical solution is obtained using Fourier series from which the resonant frequencies, mode shapes and vibration confinement by the mass layer are calculated and examined.

Vertical Track Modulus Trending, Shane Michael Farritor, Sheng Lu

Department of Mechanical and Materials Engineering: Faculty Publications

Systems and methods for determining a trend in Vertical track modulus are disclosed in accordance with embodiments of the present invention. Vertical deflection data is collected along a particular section of railroad track. A first set of Vertical track modulus is determined, based in part, on the collected vertical deflection data. At a second time, vertical deflection data is again collected along the particular section of railroad track to be used in determining a second set of vertical track modulus. At least the first and second sets of Vertical track modulus are analyzed to determine a math ematical algorithm that …

The Effect Of Axial Conduction On Heat Transfer In A Liquid Microchannel Flow, Kevin D. Cole, Barbaros Çetin

Department of Mechanical and Materials Engineering: Faculty Publications

Analysis is presented for conjugate heat transfer in a parallel-plate microchannel. Axial conduction in the fluid and in the adjacent wall are included. The fluid is a constant property liquid with a fully-developed velocity distribution. The microchannel is heated by a uniform heat flux applied to the outside of the channel wall. The analytic solution is given in the form of integrals by the method of Green’s functions. Quadrature is used to obtain numerical results for the local and average Nusselt number for various flow velocities, heating lengths, wall thicknesses, and wall conductivities. These results have application in the optimal …

Analysis Of A Monolithic Crystal Plate Acoustic Wave Filter, Huijing He

Department of Mechanical and Materials Engineering: Faculty Publications

We study thickness–shear and thickness–twist vibrations of a finite, monolithic, AT-cut quartz plate crystal filter with two pairs of electrodes. The equations of anisotropic elasticity are used with the omission of the small elastic constant c56 . An analytical solution is obtained using Fourier series from which the res-onant frequencies, mode shapes, and the vibration confinement due to the electrode inertia are calculated and examined.

Transverse Permeability Of Fibrous Porous Media, Ali Tamayol, Majid Bahrami

Department of Mechanical and Materials Engineering: Faculty Publications

In this study, the transverse permeability of fibrous porous media is studied both experimentally and theoretically. A scale analysis technique is employed for determining the transverse permeability of various fibrous matrices including square, staggered, and hexagonal arrangements of unidirectionally aligned fibers, as well as simple two-directional mats and simple cubic structures. In the present approach, the permeability is related to the porosity, fiber diameter, and tortuosity of the medium. In addition, the pressure drop in several samples of tube banks of different arrangements and metal foams are measured in the creeping flow regime. The pressure-drop results are then used to …

Improved Rehabilitation And Exercise Machine / Machine De Reeducation Et D'Exercice Amelioree, Judith M. Burnfield, Adam Taylor, Thad W. Buster, Carla A. Nelson, Yu Shu

Department of Mechanical and Materials Engineering: Faculty Publications

An improved rehabilitation and exercise machine is provided which allows a person with physical limitations, disabilities or chronic conditions to use the machine in order to rehabilitate their muscles, improve joint flexibility, and enhance cardiovascular fitness. An embodiment of the device includes a framework, a first and second crank arm, a first and second handle bar, a first and second foot pedal, a motor and pulley assembly, a first and second coupler link, and a motor controller with speed knob,

Fracture Analysis Of Kevlar-49/Epoxy And E-Glass/Epoxy Doublers For Reinforcement Of Cracked Aluminum Plates, Ananth Ram Mahanth Kasavajhala, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

Adhesively bonded composite patch repair is an efficient means to regain load carrying capacity, alleviate the crack growth, and improve the service life of the damaged structure. In this paper, three dimensional finite element models are developed to ex­amine the fracture behavior of a single edge V-notched Aluminum plate repaired with Kevlar-49/epoxy or e-glass/epoxy pre-preg patches on both sides. Contour integral method was used for evaluating the stress intensity factor (SIF), an indicator of the crack stability. The load transfer mechanisms, stress distribution, damage variable (D), and crack mouth opening displacement (CMOD), were also presented to estimate the …

Dynamic Response Of Brain Subjected To Blast Loadings: Influence Of Frequency Ranges, Mehdi S. Chafi, Shailesh G. Ganpule, Linxia Gu, Namas Chandra

Department of Mechanical and Materials Engineering: Faculty Publications

Blast wave induced a frequency spectrum and large deformation of the brain tissue. In this study, new material parameters for the brain material are determined from the experimental data pertaining to these large strain amplitudes and wide frequencies ranging (from 0.01 Hz to 10 MHz) using genetic algorithms. Both hyperelastic and viscoelastic behavior of the brain are implemented into 2D finite element models and the dynamic responses of brain are evaluated. The head, composed of triple layers of the skull, including two cortical layers and a middle dipole sponge-like layer, the dura, cerebrospinal fluid (CSF), the pia mater and the …

Analysis Of Partially Electroded Piezoelectric Actuators With Nonuniform Thickness For The Purpose Of Reducing Actuating Shear Stress Concentration By Ansys, Nan Liu, Hongping Hu

Department of Mechanical and Materials Engineering: Faculty Publications

An elastic plate with thin piezoelectric films bonded on its two major surfaces is a typical smart structure which is used in actuation and sensing. The useful deformation of the smart structure is caused by the shear stress transferring from the actuators to the elastic plate. This shear stress is concentrated at two ends of the interface between the actuator and the plate. This concentration may induce undesirable delamination of the actuator from the plate. It was theoretically proved that actuators with partially covered electrodes have a much less concentrated actuating shear stress than that with fully ones. An actuator …

Simulation Of Electrospun Nanofiber Deposition On Stationary And Moving Substrates, Linhua Liu, Yuris A. Dzenis

Department of Mechanical and Materials Engineering: Faculty Publications

Electrospinning produces continuous fibers with diameters from single nanometers to microns by jetting polymer solutions in high electric fields. Electrospun non-woven filamentary materials attract rapidly growing interest for broad range of applications. Properties of these materials depend on their nano- and microstructure that is determined in turn by the electric field and nanofiber collector. Despite critical importance, deposition of electrospun fibers on substrates has not yet been extensively studied theoretically and new methods of nanofiber collection continue to be developed mostly empirically. The objective of this Letter was to develop and demonstrate numerical simulation of electrospun nanofiber deposition on moving …

Modeling Of Solvent Evaporation From Polymer Jets In Electrospinning, Xiang-Fa Wu, Yury Salkovskiy, Yuris A. Dzenis

Department of Mechanical and Materials Engineering: Faculty Publications

Solvent evaporation plays a critical role in nanofiber formation in electrospinning. Here, we present a nonlinear mass diffusion-transfer model describing the drying process in dilute polymer solution jets. The model is used to predict transient solvent concentration profiles in polyacrylonitrile/ N,N-dimethylformamide (PAN/DMF) jets with the initial radii ranging from 50µm down to 100 nm. Numerical simulations demonstrate high transient inhomogeneity of solvent concentration over the jet cross-section in microscopic jets. The degree of inhomogeneity decreases for finer, submicron jets. The simulated jet drying time decreases rapidly with the decreasing initial jet radius, from seconds for microjets to single milliseconds for …

More Carrot Than Stick: Encouraging Computer Programming In Thermal Design Projects, Kevin D. Cole

Department of Mechanical and Materials Engineering: Faculty Publications

Students will do almost anything to avoid using thermal-property tables. In this paper, Matlab-based thermal-property software is described as an enticement for students to do computer programming in the design of thermal systems. Downloaded shareware was used for steam properties in a steam-cycle project, and an air-property package was developed for use with a gas-turbine project. Although the use of computer programming required considerable effort by both instructor and students, most students did gain a better appreciation of the utility of writing computer programs as part of engineering design. Student evaluations of the course were not significantly affected compared to …

Role Of Helmet In The Mechanics Of Shock Wave Propagation Under Blast Loading Conditions, Shailesh G. Ganpule, Linxia Gu, Aaron L. Alai, Namas Chandra

Department of Mechanical and Materials Engineering: Faculty Publications

The effectiveness of helmets in extenuating the primary shock waves generated by the explosions of improvised explosive devices is not clearly understood. In this work, the role of helmet on the overpressurization and impulse experienced by the head were examined. The shock wave–head interactions were studied under three different cases: (i) unprotected head, (ii) head with helmet but with varying head–helmet gaps and (iii) head covered with helmet and tightly fitting foam pads. The intensification effect was discussed by examining the shock wave flow pattern and verified with experiments. A helmet with a better protection against shock wave is suggested.

Effects Of Mass Layer Nonuniformity On A Quartz-Crystal Microbalance, Nan Liu, Jiashi Yang, Weiqiu Chen

Department of Mechanical and Materials Engineering: Faculty Publications

We study the effects of the nonuniform thickness of a thin mass layer on a quartz-crystal microbalance. A theoretical analysis is performed on thickness-shear (TSh) vibration of an AT-cut quartz plate with a nonuniform mass layer. Mindlin’s 2-D equation for TSh vibration of a quartz plate is used. An elliptical mass layer with stepped thickness is considered which allows an exact analysis based on the plate equation. Free vibration frequencies and modes are obtained. The effects of the mass layer nonuniformity are examined. Results show that a mass layer thicker at the center tends to confine more modes under the …

Intermediate Layers In Tandem Organic Solar Cells, Yongbo Yuan, Jinsong Huang, Gang Li

Department of Mechanical and Materials Engineering: Faculty Publications

Tandem structures can boost the efficiency of organic solar cell to more than 15%, compared to the 10% limit of single layer bulk heterojunction devices. Design and fabricating of intermediate layers plays a very important role to achieve high device performance. This article will review the main experimental progresses of tandem organic solar cells, and focus on the intermediate layers (charge recombination layers) in both thermal evaporated and solution processed organic tandem solar cell devices.

A Model Of Giant Vacuole Dynamics In Human Schlemm’S Canal Endothelial Cells, Ryan M. Pedrigi, David Simon, Ashley Reed, W. Daniel Stamer, Darryl R. Overby

Department of Mechanical and Materials Engineering: Faculty Publications

Aqueous humour transport across the inner wall endothelium of Schlemm’s canal likely involves flow through giant vacuoles and pores, but the mechanics of how these structures form and how they influence the regulation of intraocular pressure (IOP) are not well understood. In this study, we developed an in vitro model of giant vacuole formation in human Schlemm’s canal endothelial cells (HSCECs) perfused in the basal-to-apical direction (i.e., the direction that flow crosses the inner wall in vivo) under controlled pressure drops (2 or 6 mmHg). The system was mounted on a confocal microscope for time-lapse en face imaging, and cells …

Achieving High Efficiency Laminated Polymer Solar Cell With Interfacial Modified Metallic Electrode And Pressure Induced Crystallization, Yongbo Yuan, Yu Bi, Jinsong Huang

Department of Mechanical and Materials Engineering: Faculty Publications

We report efficient laminated organic photovoltaic device with efficiency approach the optimized device by regular method based on Poly(3-hexylthiophene-2,5-diyl) and [6,6]-phenyl-C₆₁-butyric acid methyl ester (PCBM). The high efficiency is mainly attributed to the formation of a concrete polymer/metal interface mechanically and electrically by the use of electronic-glue, and using the highly conductive and flexible silver film as anode to reduce photovoltage loss and modifying its work function for efficiency hole extraction by ultraviolet/ozone treatment, and the pressure induced crystallization of PCBM.

In Vitro Models For Glaucoma Research: Effects Of Hydrostatic Pressure, Yuan Lei, Shadi Rajabi, Ryan M. Pedrigi, Darryl R. Overby, A. Thomas Read, C. Ross Ethier

Department of Mechanical and Materials Engineering: Faculty Publications

PURPOSE. The response of cells (e.g., optic nerve head [ONH] cells) to mechanical stress is important in glaucoma. Studies have reported the biological effects of hydrostatic pressure on ONH cells cultured on a rigid substrate. An apparatus, designed to independently vary hydrostatic pressure and gas tension (including oxygen tension) in culture medium, was used to evaluate the effects of pressure and tension on cell migration, shape, and α-tubulin architecture in a transformed cell line (DITNC1 rat cortical astrocytes).

METHODS. During the assay period, cells were exposed to one of four experimental configurations: (1) control pressure and control gas tension; (2) …

Impact Of Elliptical Trainer Ergonomic Modifications On Perceptions Of Safety, Comfort, Workout, And Usability For People With Physical Disabilities And Chronic Conditions, Judith M. Burnfield, Yu Shu, Thad W. Buster, Adam P. Taylor, Carl A. Nelson

Department of Mechanical and Materials Engineering: Faculty Publications

Background The popularity of elliptical training has grown in rehabilitation, fitness, and home settings as a means for improving fitness and walking, yet many people with physical disabilities and chronic conditions experience difficulties when trying to use elliptical trainers.

Objective The purpose of this study was to compare, for people with disabilities and chronic conditions, perceptions of safety, comfort, workout, and usability of 4 elliptical trainers before and after the development of a set of low-cost adaptations.

Design This study was a quasi-experimental repeated-measures investigation.

Methods Twenty adults with diverse medical conditions and functional abilities evaluated 4 elliptical trainers for …

Assessment Of Shape Memory Alloy Stent Deployment In A Stenosed Artery, Shijia Zhao, Linxia Gu, Stacey R. Froemming

Department of Mechanical and Materials Engineering: Faculty Publications

Purpose — Shape memory alloy (SMA) stents have been used increasingly for the treatment of complex arterial occlusions. There is an immediate need to quantify the mechanical performance of SMA stents to open occluded arteries.
Methods — The stent crimping and expanding process was assessed through both numerical modeling and in-vitro studies. The implantation of a SMA stent in curved arteries with eccentric stenosis were simulated to evaluate the effect of artery curvature on arterial mechanics.
Results — The crimping process stored a considerable amount of strain energy in the stent, which were then released through self-expansion until a balance …