Mechanical Engineering Commons^™

Superharmonic Resonance Of Second Order For Electrostatically Actuated Mems Cantilevers, Martin Amador Botello

Theses and Dissertations

The nonlinear dynamics of electrostatically actuated micro-electro-mechanical system (MEMS) cantilever resonators are investigated. The applied Alternating Current (AC) voltage is in the realm of superharmonic resonance of the second order (near one-fourth of the natural frequency of the resonator) and hard excitations. Method of Multiple Scales (MMS) and Reduced Order Models (ROMs) are used to solve the dimensionless partial differential equation (PDE) of motion along with boundary and initial conditions. MMS transforms the PDE of motion into zero-order and first-order problems. ROMs uses mode shapes of vibration for undamped cantilever resonator as a basis of functions. ROM is …

Multifunctional Carbon Systems (Interlaminated Carbon Nanofiber Mats/ Carbon Nanotubes Polymer Composites), Homero Gonzalez Guardiola

Theses and Dissertations

Carbon nanomaterials have been an attractive topic within diverse industrial sectors given their outstanding properties for decades. One of the properties that has been calling attention is it’s shielding effectiveness (SE) for electromagnetic interference (EMI), because of the constant race of improving portable electronic and wireless communication devices among other applications. The present study, analyzes the properties of interlaminated Carbon Nanofiber (CNF) mats/Carbon Nanotubes (CNT) polymer composites, emphasizing in its capability to shield EMI. The CNF mats were developed with Polyvinyl alcohol (PVA) as a precursor and by means of the Forcespinning® technology which uses centrifugal force to create fibers …

Lead Doped Carbon Nanofibers In Li-Ion Batteries, Omar Torres

Theses and Dissertations

Lead acid batteries have been a very reliable rechargeable battery since its inception in the mid-1800s. Lithium-Ion batteries have been sought out for their light-weight and capacity of holding large amounts of energy in a small amount of space. Few studies have been conducted in the use of lead in lithium-ion batteries.

In this thesis, lead-doped carbon nanofibers were produced by using the Forcespinning® method and used as an anode on a lithium-ion battery. The morphology, material characterization and thermal properties of the anode material were analyzed using the Scanning Electron Microscopy (SEM), Energy Dispersive X-Ray Spectroscopy (EDS), Thermogravimetric Analysis …

Fibers For Skin Regeneration, Astrid Michelle Rodriguez Negron

Theses and Dissertations

This thesis presents the successful development of biocompatible Polyvinyl Butyral (PVB), PVB/Polylysine and PVB/Tannic Acid (TA)/Polylysine fibers from an ethanol solution, Polyhydroxybutyrate (PHB), PHB/Polylysine, PHB/TA/Polylysine fibers from a chloroform solution and Chitosan (CH)/Pullulan (PL)/TA and CH/PL/TA/Polylysine fibers from an aqueous solution. The fibers were mass produced utilizing the Forcespinning® (FS) technology. The morphology of the fibers was characterized using a scanning electron microscope (SEM) and the fibers average diameter was calculated. The thermal properties of the fibers were characterized using a thermogravimetric analyzer (TGA) and a differential scanning calorimeter (DSC). The antibacterial activity of the fibers was assessed using against …

The Effect Of Heat Generation In The Railroad Bearing Thermoplastic Elastomer Suspension Element On The Thermal Behavior Of Railroad Bearing Assembly, Oscar Osvaldo Rodriguez

Theses and Dissertations

Understanding the internal heat generation of the railroad bearing elastomer suspension element during operation is essential to predict its dynamic response and structural integrity, as well as to predict the thermal behavior of the complete railroad bearing assembly including the bearing adapter. The latter is essential for sensor selection and placement within the adapter (e.g., typical temperature sensors have operating ranges of up to 125°C or 257°F). The internal heat generation is a function of the loss modulus, strain, and frequency. Based on experimental studies, estimations of internally generated heat within the thermoplastic elastomer pad were obtained. The calculations show …

The Use Of Mixed Organic/Ionic Liquid Electrolytes With Forcespun Metal Oxides/Carbon Microfiber Electrodes In Lithium Ion Batteries, Jahaziel Villarreal

Theses and Dissertations

Conventional Lithium-Ion Battery (LIB) electrolytes have serious safety concerns because of highly flammability. In order to mitigate this drawback, alternative electrolytes with low volatility and non-flammable need to be synthesis. Ionic liquids (ILs) and mixed organic ionic liquid electrolytes (MOILEs) are the most suitable replacement for the highly flammable commercial organic electrolytes. In this academic investigation, a new perspective on the electrochemical performance of the ionic liquid EMI-TFSI as an alternate non-flammable electrolyte. In parallel, the use of Forcespun nanofibers as binder-free anodes will be analyzed to further improve overall electrochemical performance.

The Use Of Fe3o4/Carbon Composite Fibers As Anode Materials In Lithium Ion Batteries, Howard Campos, Jonathan Ayala, Carolina Valdes, Jason Parsons, Mataz Alcoutlabi

Mechanical Engineering Faculty Publications

In the present work, results on the synthesis and mass production of polymer/ceramic composite fibers through Forcespinning® (FS) are reported. Magnetite (Fe3O4), has been considered as a good anode material for Lithium‒Ion Batteries (LIBs) due to its high theoretical capacity (~924 mAhg-1), low cost, and low toxicity. The Fe3O4/carbon composite, in the present study, was achieved through Forcespinning iron (III) acetylacetonate /polyacrylonitrile (PAN) precursor solution with stabilization in air at 280°C followed by carbonization at 600°C under argon. The electrochemical cyclic performance of Fe3O4/C composite fibers was investigated by galvanostatic charge/discharge experiments. The results showed the Fe3O4/C composite fiber anode …

Modeling Of Aggregation And Gelation Of Nanoparticles Using Quadrature Method Of Moments, Elsayed Abdelfatah, Maysam Pournik

Mechanical Engineering Faculty Publications

Applications of Nanotechnology are growing significantly in the petroleum industry such as oil recovery, and well stimulation. In aqueous media, silica nanoparticles aggregate if there is sufficient attractive energy between nanoparticles. Aggregate size distribution evolves as aggregation continues, and once it spans the space, it forms a gel. The objective of this study is to study the aggregation and gelation kinetics in the batch. Population Balance equation (PBE) is used to model the kinetics of aggregation. Quadrature method of moments (QMOM) is used to convert the PBE with continuous distribution of nanoparticle size into a set of moment equations for …

Functionalized Graphene Oxide As Reinforcement In Epoxy Based Nanocomposites, F. V. Ferreira, F. S. Brito, W. Franceschi, E. A. N. Simonetti, L. .S Cividanes, Mircea Chipara, Karen Lozano

Mechanical Engineering Faculty Publications

The effects of amine-modified graphene oxide on dispersion and micro-hardness of epoxy based nanocomposites are reported. Graphene oxide was prepared by the modified Hummers method followed by hexamethylenediamine functionalization. Analysis conducted through Fourier transform infrared spectroscopy, Raman spectroscopy, X-ray photoelectron spectroscopy and atomic force microscopy-based infrared spectroscopy show that the functionalization process effectively promoted a replacement of oxygen with amine groups while simultaneously creating defects in the graphitic structure. An increase in hardness was observed for the developed nanocomposites.

Direct Numerical Simulation Of Transverse Ripples: 2. Self-Similarity, Bedform Coarsening, And Effect Of Neighboring Structures, ‪Nadim Zgheib, J. J. Fedele, D. C. J. D. Hoyal, M. M. Perillo, S. Balachandar

Mechanical Engineering Faculty Publications

Coupled bed-flow direct numerical simulations investigating the early stages of pattern formation and bedform (ripple) interactions were examined in a previous paper (Part 1), making use of the resolved flow field. In this paper (Part 2), we compare our results to published experimental data and provide an extensive quantitative analysis of the bed using spectral analysis and two-point correlations. The effect of the mobile rippled bed on the flow structure and turbulence is investigated locally (at specific streamwise locations) and over the entire computational domain. We show that developing ripples attain a self-similar profile in both the shape and the …

Direct Numerical Simulation Of Transverse Ripples: 1. Pattern Initiation And Bedform Interactions, ‪Nadim Zgheib, J. J. Fedele, D. C. J. D. Hoyal, M. M. Perillo, S. Balachandar

Mechanical Engineering Faculty Publications

We present results of coupled direct numerical simulations between flow and a deformable bed in a horizontally periodic, turbulent open channel at a shear Reynolds number of Reτ = 180. The feedback between the temporally and spatially evolving bed and the flow is enforced via the immersed boundary method. Using the near-bed flow field, we provide evidence on the role of locally intense near-bed vortical structures during the early stages of bed formation, from the emergence of quasi-streamwise streaks to the formation of incipient bedform crestlines. Additionally, we take a new look at a number of defect-related bedform interactions, …

High-Throughput Production With Improved Functionality And Graphitization Of Carbon Fine Fibers Developed From Sodium Chloride-Polyacrylonitrile Precursors, Mandana Akia, Lee Cremar, Manuel Seas, Jahaziel Villarreal, Alejandra Valdez, Mataz Alcoutlabi, Karen Lozano

Mechanical Engineering Faculty Publications

Fine polyacrylonitrile (PAN) fibers were produced through a scalable centrifugal spinning process. Sodium chloride (NaCl) was added to the PAN-dimethylformamide solution to decrease the surface tension and consequently promote a decrease in fiber diameter while increasing the fiber output. The fiber preparation process involved the centrifugal spinning of the PAN-based solution; developed fibers were stabilized in air at 240°C followed by carbonization at 800°C under a Nitrogen atmosphere. The addition of sodium chloride to the PAN solution led to a 37% decrease in the carbon fiber diameter. The carbon fibers were analyzed by scanning electron microcopy, transmission electron microscopy (TEM), …

High-Throughput Production With Improved Functionality And Graphitization Of Carbon Fine Fibers Developed From Sodium Chloride-Polyacrylonitrile Precursors, Mandana Akia, Lee Cremar, Manuel Seas, Jahaziel Villarreal, Mataz Alcoutlabi, Karen Lozano

Mechanical Engineering Faculty Publications

Fine polyacrylonitrile (PAN) fibers were produced through a scalable centrifugal spinning process. Sodium chloride (NaCl) was added to the PAN-dimethylformamide solution to decrease the surface tension and consequently promote a decrease in fiber diameter while increasing the fiber output. The fiber preparation process involved the centrifugal spinning of the PAN-based solution; developed fibers were stabilized in air at 240°C followed by carbonization at 800°C under a Nitrogen atmosphere. The addition of sodium chloride to the PAN solution led to a 37% decrease in the carbon fiber diameter. The carbon fibers were analyzed by scanning electron microcopy, transmission electron microscopy (TEM), …

Responsiveness Comparison Between A Lift-Type And Drag-Type Rotor In Waves, Yingchen Yang, Fredrick A. Jenet, Deyanira Jimenez, Brandon Benavides, Jesus Cerda, Angel Lopez

Mechanical Engineering Faculty Publications

Our recent progress on development of a vertical-axis unidirectional rotary wave energy converter (WEC) is discussed in this work. The WEC features a vertical-axis rotor that preforms unidirectional rotation in waves. The vertical axis arrangement makes the WEC respond well to waves from any direction with no realignment needs. And, the unidirectional behavior of the rotor promises no wave frequency discrimination, which is in comparison to reciprocating WECs that employ the resonant principle and are very frequency-specific. In our earlier proof-of-concept studies, we have successfully demonstrated two types of rotor designs: a lift type employing hydrofoil blades and a drag …

Development Of Antimicrobial Chitosan Based Nanofiber Dressings For Wound Healing Applications, Lee Cremar, Jorge Gutierrez, Jennifer Martinez, Luis A. Materon, Robert Gilkerson, Fenghua Xu, Karen Lozano

Mechanical Engineering Faculty Publications

Objective(s): Chitosan based composite fine fibers were successfully produced via a centrifugal spinning technology. This study evaluates the ability of the composites to function as scaffolds for cell growth while maintaining an antibacterial activity.

Materials and Methods: Two sets of chitosan fiber composites were prepared, one filled with anti-microbial silver nanoparticles and another one with cinnamaldeyhde. Chitosan powder was dissolved in trifluoroacetic acid and dichloromethane followed by addition of the fillers. The fiber output was optimized by configuring the polymer weight concentration (7, 8, and 9 w/w% chitosan) and applied angular velocity (6000-9000 RPM) within the spinning process.

Results: …

Single Tower Crane Allocation Models Using Ant Colony Optimization, Carlos Abelardo Treviño

Theses and Dissertations

The construction industry greatly benefits from the utilization of heavy machines and equipment to accomplish successful projects. Tower cranes, in specific, have a crucial role in the transportation of material loads across the site. Because these machines are fixed to the ground, it is essential for planners and managers to position them in a location that provides the most efficient transfer of materials possible. This is commonly known as the tower crane allocation problem, and many researchers have attempted to optimize the tower crane location using mathematical, artificial intelligence, and simulation approaches. However, many works from the literature contain critical …

Design Of Metal Oxides/Metal Sulfides For The Improvement Of Sodium Ion Batteries, David E. Flores

Theses and Dissertations

Herein, the improvement in performance for sodium ion batteries (NIBs) is discussed from available literature and work conducted in the laboratory setting to demonstrate the ability of sodium to perform in the world of energy storage. The reason that sodium is being explored as an alternative to Lithium in energy storage devices is because of the potential depletion of the lithium in the world causing lithium prices to surge. Researchers show that many Sn, Sb, Ge, and other composites perform well as anode materials within NIBs. The research conducted in the dissertation applies the Forcespinning method to produce fibers for …

Study Of Latent Heat Thermal Energy Storage Systems For Concentrated Solar Power Plants, Hermes Chirino

Theses and Dissertations

Concentrated Solar Power (CSP) using phase change material (PCM) as the storage medium in the Thermal Energy Storage (TES) system is a promising technology for large scale utilization of solar thermal energy because heat latent heat thermal energy storage (LHTES) systems can store more energy as the latent heat during the melting process.

This study analyzes the different dimensionless parameters from the 1-D transient enthalpy-based mathematical model used to simulate the heat transfer and flow within the LHTES system. These dimensionless parameters are varied and analyzed with the main objective of increasing thermal energy storage efficiency and exergy efficiency of …

Effect Of Processing Parameters On The Electrochemical Performance Of Forcespun Metal Oxide/Carbon Composite Fibers For Li-Ion Batteries, Howard A. Campos

Theses and Dissertations

Metal oxides have been gaining interest as electrode materials for rechargeable Li-ion batteries due to various properties including low cost, low toxicity, and high theoretical capacity. In this research work the effect of two different metal oxide/carbon fiber composites, Fe3O4/C and ZnO/C, on the electrochemical performance for Li-ion batteries will be explored. This is also the first time that results are reported, to the best of our knowledge, of these fiber composites through the Forcespinning ® method. Scanning electron microscopy (SEM), Energy-Dispersive X-ray Analysis (EDS), X-ray photoelectron spectroscopy (XPS), powder X-ray diffraction (XRD), and electrochemical analysis were used to investigate …

Nitrogen Doped Carbon Nanofibers Derived From Water-Soluble Precursors, Lee Cremar, Ben Jones, Nicole Martinez, Gustavo Mejia, Hilario Cortez, Edgar Muñoz, Rocío Nava, Karen Lozano

Mechanical Engineering Faculty Publications

Nitrogen doped carbon fibers were synthesized from polyvinyl alcohol (PVA), a water soluble precursor. The PVA fine fibers were first developed by centrifugally spinning an aqueous based solution using Forcespinning® technology. The precursor fibers were then exposed to sulfuric acid vapors to partially carbonize and stabilize the fibers for further heat treatment. For nitrogen doping, the fibers were exposed to two different heat treatment routes. One was under a nitrogen atmosphere at 850°C followed by exposure to ammonia gas at 500°C. The second route consisted of heating the treated fibers in pure ammonia gas only, up to 850°C. Both heating …

Suspension-Driven Gravity Surges On Horizontal Surfaces: Effect Of The Initial Shape, ‪Nadim Zgheib, T. Bonometti, S. Balachandar

Mechanical Engineering Faculty Publications

We present results from highly resolved direct numerical simulations of canonical (axisymmetric and planar) and non-canonical (rectangular) configurations of horizontal suspension-driven gravity surges. We show that the dynamics along the initial minor and major axis of a rectangular release are roughly similar to that of a planar and axisymmetric current, respectively. However, contrary to expectation, we observe under certain conditions the final extent of the deposit from finite releases to surpass that from an equivalent planar current. This is attributed to a converging flow of the particle-laden mixture toward the initial minor axis, a behaviour that was previously reported for …

Polyethylene Oxide—Fullerene Nanocomposites, Nasar Ali, Dorina M. Chipara, Karen Lozano, James R. Hinthorne, Mircea Chipara

Mechanical Engineering Faculty Publications

Polyethylene oxide – fullerene nanocomposites have been prepared by using the solution path with water as solvent (only for the polymer). The dispersion of C60 within the polymer solution was achieved by high power sonication. The study aims to a better understanding on the effect of C60 nanoparticles on the macromolecular chains. Raman Wide Angle X Ray spectroscopy, Differential Scanning Calorimetry, and Thermogravimetric Analysis were used to inspect the interactions between the nanofiller and macromolecular chains. The experimental results revealed a completely different behavior of fullerene dispersed within polymeric matrices than using carbon nanotubes or nanofibers as nanofiller. …

A Vertical Axis Rotor For Wave Energy Conversion, Yingchen Yang, Joab Soto, Francisco Salazar

Mechanical Engineering Faculty Publications

The present work augments vertical-axis unidirectional wave energy converter (WEC) designs with a new approach. The enabling technique is the hydrodynamic design of a special rotor, which consists of a series of uniquely shaped blades in a certain formation. Specifically, individual blades are realized by revolving a two-dimensional symmetric hydrofoil about its chord line. Then the blades are arranged around a vertical shaft in a desired formation to form the rotor. When driven by an approaching flow through interaction, the rotor naturally rotates about the vertical shaft in a predefined direction. The approaching flow could be from any spatial direction, …

Past, Present And Future Of Surgical Meshes: A Review, Karen Baylón, Perla Rodríguez-Camarillo, Alex Elías-Zúñiga, Jose Antonio Díaz-Elizondo, Robert Gilkerson, Karen Lozano

Mechanical Engineering Faculty Publications

Surgical meshes, in particular those used to repair hernias, have been in use since 1891. Since then, research in the area has expanded, given the vast number of post-surgery complications such as infection, fibrosis, adhesions, mesh rejection, and hernia recurrence. Researchers have focused on the analysis and implementation of a wide range of materials: meshes with different fiber size and porosity, a variety of manufacturing methods, and certainly a variety of surgical and implantation procedures. Currently, surface modification methods and development of nanofiber based systems are actively being explored as areas of opportunity to retain material strength and increase biocompatibility …

Characterization Of Lift And Drag On Two Dimensional Airfoils With And Without Sinusoidal Leading Edges, Gregorio I. Acosta

Theses and Dissertations

An experimental investigation was taken on a 63-021 NACA airfoil, to characterize lift and drag and how the effects of sinusoidal leading edges affect the aerodynamic properties. A theoretical model is also purposed by implementing a perturbation on thin-airfoil theory.

Two sets of airfoils were machined and tested inside a low-speed open circuit wind tunnel. Data from a pressure scanner and particle image velocity will give an insight of how the modified leading edges affect the aerodynamic properties. A Fourier series expansion was used to solve for the lifting-line model, by use of thin-airfoil theory and complex number theory.

Radiative Heat Transfer Analysis Of Railroad Bearings For Wayside Hot-Box Detector Optimization, Arthur Mealer, Constantine Tarawneh, Stephen Crown

Mechanical Engineering Faculty Publications

The railroad industry utilizes wayside detection systems to monitor the temperature of freight railcar bearings in service. The wayside hot-box detector (HBD) is a device that sits on the side of the tracks and uses a non-contact infrared sensor to determine the temperature of the train bearings as they roll over the detector. Various factors can affect the temperature measurements of these wayside detection systems. The class of the railroad bearing and its position on the axle relative to the position of the wayside detector can affect the temperature measurement. That is, the location on the bearing cup where the …

Hysteresis Heating Of Railroad Bearing Thermoplastic Elastomer Suspension Element, Oscar O. Rodriguez, Arturo A. Fuentes, Constantine Tarawneh, Robert E. Jones

Mechanical Engineering Faculty Publications

Thermoplastic elastomers (TPE’s) are increasingly being used in rail service in load damping applications. They are superior to traditional elastomers primarily in their ease of fabrication. Like traditional elastomers they offer benefits including reduction in noise emissions and improved wear resistance in metal components that are in contact with such parts in the railcar suspension system. However, viscoelastic materials, such as the railroad bearing thermoplastic elastomer suspension element (or elastomeric pad), are known to develop self-heating (hysteresis) under cyclic loading, which can lead to undesirable consequences. Quantifying the hysteresis heating of the pad during operation is therefore essential to predict …

Front Dynamics Of Elliptical Gravity Currents On A Uniform Slope, S. J. Zhu, ‪Nadim Zgheib, S. Balachandar, A. Ooi

Mechanical Engineering Faculty Publications

In the present investigation, we report data from direct numerical simulations of elliptical, finite release, Boussinesq gravity currents propagating down a uniform slope. The study comprises a series of simulations of elliptical gravity currents on a range of slope angles. The shape parameters are varied to study the effects of the initial cross-sectional aspect ratio (Λ0) and mean height to lock radius ratio (Γ) on the dynamics of the gravity current. It is found that the long-time development of the current spatial mass distribution is influenced by its initial shape at smaller slope angles (θ=5∘ and 10∘) whereas the long-time …

Discrete Element Analysis Of Scb Variability: Asphalt Mixtures, David Saul Renteria

Theses and Dissertations

The Semi-Circular Bending (SCB) test was modeled using the Discrete Element Method (DEM) implemented in numerical software Particle Flow Code (PFC). The fracture analysis of the SCB was studied using two mixtures gradation, Superpave and Coarse Matrix High Binder. The aggregate phase in the model was achieved by using two-dimensional aggregate images with different angularity indexes. The study of the variability of the SCB extends to the random generation of aggregate particles and air voids in the model, in addition to changing the properties at the interface between the aggregate and mastic phases. Results indicate the strong influence of the …

Casimir And Van Der Waals Effects On Electrostatically Actuated Nems Resonator Sensors, Christian Reyes

Theses and Dissertations

The behavior of nano and micro-electromechanical systems (N/MEMS) cantilever beams under electrostatic actuation is studied. The cantilever system is actuated by soft AC voltage that is set to a frequency of near half natural and near natural frequency of the beam. These actuating frequencies result in primary and parametric resonances, respectively. Two methods are used to analytically model the behavior of the cantilever. The first method is Method of Multiple Scales (MMS), which is a perturbation method that works for small parameters. The second method is the Reduced Order Method (ROM), which is a Galerkin method that works for large …