Mechanical Engineering Commons^™

Test 1982: New Holland Ts6030, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Feasibility Study Of Solar Driven Underground Cooling System, Michel E. Shafik

Durham School of Architectural Engineering and Construction: Dissertations, Theses, and Student Research

In the United States the peak electrical use occurs during the summer. In addition, the building sector consumes a major portion of the annual electrical energy consumption. One of the main energy consuming components in the building sector is the Heating, Ventilation, and Air-Conditioning (HVAC) systems. This research studies the feasibility of implementing a solar driven underground cooling system that could contribute to reducing building cooling loads. The developed system consists of an Earth-to-Air Heat Exchanger (EAHE) coupled with a solar chimney that provides a natural cool draft to the test facility building at the Solar Energy Research Test Facility …

Dynamics Of Fibrillar Precursors Of Shishes As A Function Of Stress, Luigi Balzano, Dario Cavallo, Tim B. Van Erp, Zhe Ma, Jan-Willem Housmans, Lucia Fernandez-Ballester, Gerrit W. M. Peters

Department of Engineering Mechanics: Faculty Publications

Shishes are fibrillar crystallites that can be created by deforming a polymer melt. The formation of shishes takes place when flow is strong enough to stretch molecules. In the early stages, bundles of stretched molecules with pre-crystalline order form metastable precursors whose stability depends on their size and, hence, on the stress level. We find that for a specific isotactic polypropylene, close to the nominal melting point, a stress larger than 0.10 MPa leads to stable fibrillar precursors that are partially crystalline immediately after flow. On the other hand, below 0.10 MPa, the aspect ratio of precursors tends to unity …

Studies Of Dynamic Crack Propagation And Crack Branching With Peridynamics, Youn Doh Ha, Florin Bobaru

Department of Engineering Mechanics: Faculty Publications

In this paper we discuss the peridynamic analysis of dynamic crack branching in brittle materials and show results of convergence studies under uniform grid refinement (m-convergence) and under decreasing the peridynamic horizon (δ-convergence). Comparisons with experimentally obtained values are made for the crack-tip propagation speed with three different peridynamic horizons.We also analyze the influence of the particular shape of themicro-modulus function and of different materials (Duran 50 glass and soda-lime glass) on the crack propagation behavior. We show that the peridynamic solution for this problem captures all the main features, observed experimentally, of dynamic crack propagation and branching, as well …

Finite Element Analysis Of Cracks In Aging Aircraft Structures With Bonded Composite-Patch Repairs, Linxia Gu, Ananth Ram Mahanth Kasavajhala, Shijia Zhao

Department of Mechanical and Materials Engineering: Faculty Publications

Bonded composite-patch repair has been used to transfer load from cracked structures to the reinforcement such that subsequent crack propagation is reduced. In this study,the mechanical behavior of a single edge v-notch A17075-T6 plate repaired with 1-ply and 4-ply composite patches was investigated through the finite element method. Contour integral method was used to define and evaluate the stress intensity factors at the crack tip. The effect of the adhesive epoxy film, patch material, thickness and ply orientations on the evolution of the stress intensity factor (SIF) of the repaired structure was examined. The results indicated that the SIF of …

Thermal Models Of Railroad Wheels And Bearings, Kevin D. Cole, Constantine M. Tarawneh, Arturo A. Fuentes, B. M. Wilson, L. Navarro

Department of Mechanical and Materials Engineering: Faculty Publications

The rolling surface for railroad wheels can be a heat source that may have an impact on the performance of the wheel bearing. In this study, experimental data from an electrically-heated railroad wheel set is analyzed by constructing thermal models of the wheel set. A steady finite-element model, a steady-analytical model, and a transient lumped-parameter model are discussed. Model parameters are determined from careful comparisons with the experimental data. The lumped-parameter model given here is intended as a simple predictive tool for determining when wheel heating caused by rail operations will have an impact on bearing temperature. The model parameters …

Nonequilibrium Thermodynamics Modeling Of Coupled Biochemical Cycles In Living Cells, Yaşar Demirel

Yaşar Demirel Publications

Living cells represent open, nonequilibrium, self organizing, and dissipative systems maintained with the continuous supply of outside and inside material, energy, and information flows. The energy in the form of adenosine triphosphate is utilized in biochemical cycles, transport processes, protein synthesis, reproduction, and performing other biological work. The processes in molecular and cellular biological systems are stochastic in nature with varying spatial and time scales, and bounded with conservation laws, kinetic laws, and thermodynamic constraints, which should be taken into account by any approach for modeling biological systems. In component biology, this review focuses on the modeling of enzyme kinetics …

Method Of Transferring Strained Semiconductor Structure, Michael Nastasi

Department of Mechanical and Materials Engineering: Faculty Publications

The transfer of strained semiconductor layers from one substrate to another substrate involves depositing a multilayer structure on a substrate having surface contaminants. An interface that includes the contaminants if formed in between the deposited layer and the substrate. Hydrogen atoms are introduced into the structure and allowed to diffuse to the interface. Afterward, the deposited multilayer structure is bonded to a second substrate and is separated away at the interface, which results in transferring a multilayer structure from one substrate at least one strained semiconductor layer and at least one strain-induced seed layer. The strain-induced seed layer can be …

Self-Organized Nanolayers Of Organosilane Molecules, Ocelio V. Lima

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

There is a high degree of interest in organic thin films for lightweight, low power, rugged and flexible electronics. Conjugated organic molecules with polycyclic rings are being considered a major enabler of such applications. Due to a surface tension mismatch between the organic molecule with the inorganic support (mainly silicon oxides), molecular packing inside these thin films is often disordered, which suppresses the device performance. There are major efforts focused on modifying the bulk properties, for instance, maximizing orbital overlaps in the solid state, little attention was paid to receive long-range ordered thin films. A novel approach to afford conjugated …

Optical Properties Of Semiconducting Boron Carbide For Neutron Detection Applications, Ravi B. Billa

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Solid state neutron detection devices based on semiconducting boron carbide have the potential for nearly ideal neutron detection effciency for thermal neutrons. The present work is focused on characterizing optical properties of this semiconducting boron carbide material as a step in further development of the material for neutron detection and other applications.

Semiconducting boron carbide films were grown on silicon substrates using plasma enhanced chemical vapor deposition and their optical properties were characterized using variable angle spectroscopic ellipsometry over a wide spectral range, from mid-infrared to vacuum-ultraviolet wavelengths. The effects of deposition substrate temperature and of post-deposition heat treatments on …

Thermodynamically Consistent Large Deformation Constitutive Model For Glassy Polymers, Ashwani Kumar Goel

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Polycarbonate(PC), like most glassy polymers when undergoing large deformations exhibits a very complex thermo-mechanical response. We look at PC as a model glassy polymer and examine its response to changes in loading rate, loading direction and temperature. We show that plastic flow in compression is accompanied by a change in the elastic response of PC from isotropic to anisotropic. This provides the necessity to introduce a new modeling method that can capture these changes. A finite deformation plasticity like thermodynamically consistent model is developed to capture this and the observed rate and temperature dependence. For this modeling method, we need …

Imprinting Polymerfilm On Patterned Substrate, Li Tan, Yen-Peng Kong, Stella W. Pang, Albert F. Yee

Department of Mechanical and Materials Engineering: Faculty Publications

A method of applying a pattern on a topography includes first applying a polymer film to an elastormer member, such as PDMS, to form a pad. The pad is then applied to a substrate having a varying topography under pressure. The polymer film is transferred to the substrate due to the plastic deformation of the polymer film under pressure compared to the elastic deformation of the PDMS member pulls away from the polymer layer, thereby depositing the polymer layer, thereby depositing the polymer layer upon the substrate.

Modeling And Simulation Of Interactions Between Blast Waves And Structures For Blast Wave Mitigation, Wen Peng

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Explosions occur in military conflicts as well as in various industrial applications. Air blast waves generated by large explosions move outward with high velocity, pressure and temperature. The blast waves not only incapacitate military and civilian personnel, but also damages buildings, vehicles, and other properties. Hence, there has been extensive research on how to mitigate blast wave effects. Understanding the interactions between blast waves and structures is a very important step in the development of devices for blast wave mitigation. The objective of this dissertation is to explore the complicated physical problem of blast waves impacting structures. The structures comprise …

October 2009, Tractor Museum

Lester F. Larsen Tractor Museum: Planning and Development Documents

Agenda, minutes, treasurer report, director report, docent report, associate report, activities report, test lab report

Towards Supervised Autonomous Task Completion Using An In Vivo Surgical Robot, Jason J. Dumpert

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Laparoscopy is a minimally invasive alternative to traditional abdominal surgery. Unlike traditional surgery, a laparoscopic procedure can be completed using small incisions. The use of these small incision results in reduced pain to the patient, shorter recovery times, and less trauma to skin, muscle and other tissues. However, these benefits to the patient are offset by the increased difficulty to the surgeon performing the procedure. These difficulties include reduced dexterity, reduced perception, and longer procedure times. The use of small in vivo robotic devices in minimally invasive surgery is one possible solution to these problems. The movement of these devices …

Steady-Periodic Heating Of A Cylinder, Kevin D. Cole, Paul E. Crittenden

Department of Mechanical and Materials Engineering: Faculty Publications

Steady periodic heating is an important experimental technique for measurement of thermal properties. In these methods the thermal properties are deduced from a systematic comparison between the data (such as temperature) and a detailed thermal model. This paper addresses steady-periodic heat transfer on cylindrical geometries with application to thermal-property measurements. The method of Green’s functions is used to provide a comprehensive collection of exact analytical expressions for temperature in cylinders. Five kinds of boundary conditions are treated for one-, two-, and three-dimensional geometries. For some geometries an alternate form of the Green’s function is given, which can be used for …

Development Of Guidelines For Deformable And Rigid Switch In Ls-Dyna Simulation, Ling Zhu

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

LS-Dyna simulations have been widely used in research and design to reduce fiscal and time costs. In order to improve the simulation’s efficiency, the components which experience negligible deformations are usually modeled as rigid bodies. However, the use of rigid bodies is always restricted. Though the use of more rigid bodies can save computing resources for a particular simulation, less rigid bodies are preferred for building a model in order to broaden its applications. Meanwhile, if a simulation task has multiple events, the application of rigid bodies in the particular simulation is always minimized so that it can satisfy all …

The Effects Of Combined Compression And Aging On The Properties Of Glassy Polycarbonate, Kyle W. Strabala

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Physical aging and plastic flow are known to cause changes in the properties of glassy polycarbonate (PC). Although the individual effects of physical aging and plastic flow have been studied, the combined mechanical and thermal effects have yet to be evaluated for PC at large plastic strains. This work is the first characterization of the combined effects in PC of large plastic flow followed by thermal (physical) aging. To conduct this study, samples were prepared with different extents of plastic compressive strain, up to approximately 50% engineering strain, followed by thermal aging up to 135 °C, with various …

Multiscale Modeling Of Glass Fiber Reinforced Viscoelastic Polymers Subjected To Impact Loads, Victor Ferreira Teixeira

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

New applications for polymer composite materials are occurring at a rapid pace today. These include structural components in the energy, transportation, and biomedical fields.  Many if not all of these new applications will require that part performance is insured with some degree of sustainable damage.  With the growth in the use of composite structures comes the necessity of improved methodologies that can predict more accurately the life and serviceability conditions of composite parts. Damage mechanics in two-phase composite materials is a very complex problem that has challenged researchers for many years. However, most of the available models perform only a …

Flexible Electronics Using Ion Implantation To Adhere Polymer Substrate To Single Crystal Silicon Substrate, Terry L. Alford, Douglas C. Thompson Jr., Hyunchul Kim, Michael A. Nastasi, James W. Mayer, Daniel Adams

Department of Mechanical and Materials Engineering: Faculty Publications

An electronic apparatus uses a single crystalline silicon Substrate disposed adjacent to a flexible substrate. The electronic apparatus may be a flexible flat panel display, or a flexible printed circuit board. The flexible substrate can be made from polymer, plastic, paper, flexible glass, and stainless steel. The flexible substrate is bonded to the single crystalline substrate using an ion implantation process. The ion implantation process involves the use of a noble gas Such as hydrogen, helium, Xenon, and krypton. A plurality of semiconductor devices are formed on the single crystalline silicon Substrate. The semi conductor devices may be thin film …

Force Chains And Resonant Behavior In Bending Of A Granular Layer On An Elastic Support, Kitti Rattanadit, Florin Bobaru, Konlayut Promratana, Joseph A. Turner

Department of Engineering Mechanics: Faculty Publications

In this paper we investigate the interaction between a granular layer and an elastic foundation using a coupled Discrete Element Method-Finite Element Method (DEM–FEM) computational model. We use this dynamics code to simulate quasi-static bending of the granular layer and we observe the changes taking place in the structure of the force chains for two cases: with and without rolling resistance. A reversal of the arches formed in the force chains leads to a bending resistance similar to that observed in dynamic experiments on resonant behavior under bending of a layer of sand in a container with an elastic bottom. …

Editorial: Advances In The Dynamics Of Granular Materials, Florin Bobaru, J. S. Chen, Joseph A. Turner

Department of Engineering Mechanics: Faculty Publications

Granular materials exhibit a complex array of phenomena which makes the prediction of their behavior extremely difficult. Granular materials are strongly dissipative and show collective (heap formation, jamming) and size segregation phenomena, and can propagate surface waves. They display fluidization and convective motion, and under certain vibration regimes, they tend to mix when they would otherwise segregate, and segregate when they might otherwise mix. The wide range of behaviors that granular materials can display has been one of the main factors for which the development of predictive models has continued to remain an open problem.
The papers in this Special …

Guidance Directrix Generation Using Laser Sensors, Santosh Pitla, Joe D. Luck, Scott A. Shearer

Department of Agricultural and Biological Systems Engineering: Presentations and White Papers

A sensor array consisting of two laser sensors was utilized to determine the guidance directrix (offset distance-d, heading angle-ø) that are required as reference inputs for an automated guidance system. The sensor array was evaluated in both laboratory and field conditions. Under laboratory conditions the sensor array replicated the physical profile of the target surface with a 4% error in determining the heading angle. Field tests were conducted in two types of crops; corn and alfalfa. The sensor array identified the cut-crop edge profile ahead of the tractor and replicated distinct shapes of the cut-crop edge. RMSE values in determining …

Multiscale Modeling Of Impact On Heterogeneous Viscoelastic Solids With Evolving Microcracks, Flavio V. Souza

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Multiscale computational techniques play a major role in solving problems related to viscoelastic composite materials due to the complexities inherent to these materials. In the present work, a numerical procedure for multiscale modeling of impact on heterogeneous viscoelastic solids containing evolving microcracks is proposed in which the (global scale) homogenized viscoelastic incremental constitutive equations have the same form as the local scale viscoelastic incremental constitutive equations, but the homogenized tangent constitutive tensor and the homogenized incremental history dependent stress tensor depend on the amount of damage accumulated at the local scale. Furthermore, the developed technique allows the computation of the …

A Model For Predicting The Multiscale Crack Growth Due To An Impact In Heterogeneous Viscoelastic Solids, Flavio V. Souza, David H. Allen

Department of Engineering Mechanics: Faculty Publications

A two-scale model for predicting the multiple crack growth in viscoelastic solids due to an impact is presented. The cracks are considered only at the local scale through the use of a micromechanical viscoelastic cohesive zone model. The multiscale model has been implemented in a finite-element code. In order to minimize the computation time, the local finite-element meshes are solved in parallel by multiple processors. An example problem is given in order to demonstrate the capabilities of the model.

Thermodynamically Coupled Heat And Mass Flows In A Reaction-Transport System With External Resistances, Yaşar Demirel

Yaşar Demirel Publications

Considerable work has been published on mathematically coupled nonlinear differential equations by neglecting thermodynamic coupling between heat and mass flows in reaction-transport systems. The thermodynamic coupling refers that a flow occurs without or against its primary thermodynamic driving force, which may be a gradient of temperature, or chemical potential, or reaction affinity. This study presents the modeling of thermodynamically coupled heat and mass flows of two components in a reaction-transport system with external heat and mass transfer resistances. The modeling equations are based on the linear nonequilibrium thermodynamics approach by assuming that the system is in the vicinity of global …

Analysis Of Flux-Base Fins For Estimation Of Heat Transfer Coefficient, Kevin D. Cole, C. Tarawneh, B. Wilson

Department of Mechanical and Materials Engineering: Faculty Publications

Exact solutions are given for the transient temperature in flux-base fins with the method of Green’s functions (GF) in the form of infinite series for three different tip conditions. The speed of convergence is improved by replacing the steady part by a closed-form steady solution. For the insulated-tip case, a quasi-steady solution is presented. Numerical values are presented and the conditions under which the quasi-steady solution is accurate are determined. An experimental example is given for estimation of the heat transfer coefficient (HTC) on a non-rotating roller bearing, in which the outer bearing race is treated as a transient fin.

Newsletters Of First 10 Years, Tractor Museum

Friends of the Larsen Tractor Museum

Newsletters distributed to supporters of the Larsen Tractor Museum.

1998 Spring Newsletter 1 - Non-profit Status, Dedication of Museum, Nebraska Tractor Test Law Beginnings

1998 Winter Newsletter 2 - First Annual Meeting, Library Established, State Fair Report, Winnepeg Plowing Contests

1999 Spring Newsletter 3 - Nebraska State Museum Affiliation, Fundraising Goals, Fuel Saving Devices in the 1920s

1999 Fall Newsletter 4 - Museum Studies Luis Vasquez, Tractor Raffle, Renovation Goals, Fundraising Goals, Annalyzing Tractor Test Results

1999 Winter Newsletter 5 - Mission Statement, Logo and Letterhead, Tractor Storage Facility, Bylaw Amendments, Hand Tool History, The Davidson Traction Dynamometer

2000 Spring …

Co-Op E3 Cockshutt 30 Restoration, Tractor Museum

Tractor Maintenance, Repair, and Restoration

Larsen Tractor Museum 2009 Restoration Project

Nebraska Summary: S695 Agco Rt155a, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …