Mechanical Engineering Commons^™

Magnetic Properties Study Of The Mn-Al System With Additions Of B Or C And Mechanical Milling Techniques, Timothy E. Prost

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Recently a shift in the focus of permanent magnetic research has moved from Rare Earth (RE)-based alloys to those made from more readily available elements. Because of their relatively large magnetocrystalline anisotropy, L1₀ compounds have the potential for use as permanent magnet materials. One particular alloy that is readily available and inexpensive is near equi-atomic manganese and aluminum (Mn₅₀-Al₅₀). First characterized in 1958, it did not receive much attention until more recently when RE supply chain issues made the alloy more attractive for commercial and research applications. The ferromagnetic (FM) τ-phase (L1₀) is …

Shear-Horizontal Vibration Modes Of An Oblate Elliptical Cylinder And Energy Trapping In Contoured Acoustic Wave Resonators, Huijing He, Jiashi Yang, John A. Kosinski

Department of Mechanical and Materials Engineering: Faculty Publications

We study shear-horizontal free vibrations of an elastic cylinder with an oblate elliptical cross section and a traction-free surface. Exact vibration modes and frequencies are obtained. The results show the existence of thickness-shear and thickness-twist modes. The energy-trapping behavior of these modes is examined. Trapped modes are found wherein the vibration energy is largely confined to the central portion of the cross section and little vibration energy is found at the edges. It is also shown that face-shear modes are not allowed in such a cylinder. The results are useful for the understanding of the energy trapping phenomenon in contoured …

Automated Resonant Wireless Power Transfer To Remote Sensors From An Unmanned Aerial Vehicle, Brent Griffin

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Wireless magnetic resonant power transfer is an emerging technology that has many advantages over other wireless power transfer methods due to its safety, lack of interference, and efficiency at medium ranges. In this thesis, we develop a wire- less magnetic resonant power transfer system that enables unmanned aerial vehicles (UAVs) to provide power to, and recharge batteries of, wireless sensors and other electronics far removed from the electric grid. We address the difficulties of implementing and outfitting this system on a UAV with limited payload capabilities and develop a controller that maximizes the received power as the UAV moves into …

Effects Of Acoustic Environments On Speech Comprehension By Native-English-Speaking Listeners, Zhao Peng, Lily M. Wang, Siu Kit Lau

Durham School of Architectural Engineering and Construction: Faculty Publications

This study investigates the effects of acoustic conditions on speech comprehension, rather than speech intelligibility as often reported in existing literature. Sets of 15-minute-long listening comprehension tests were developed based on the format of the Test of English for International Communication (TOEIC). Each test set includes four types of tasks: matching aural phrases to photographs, selecting appropriate responses to aural questions, and answering questions after listening to conversations (between two talkers) and talks (single talker). Within the Nebraska acoustics test chamber, native-English-speaking participants are asked to perform these tests under 15 acoustic conditions, from combinations of three background noise levels …

Design, Analysis And Testing Of Haptic Feedback System For Laparoscopic Graspers In In Vivo Surgical Robots, Nikhil Salvi

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Laparo-Endoscopic Single Site (LESS) Robotics Surgery is an advanced technology in the field of Minimally Invasive Surgery (MIS). The LESS surgical robots significantly improve the surgeon’s accuracy, dexterity and visualization, and reduce the invasiveness of surgical procedure results in faster recovery time and improved cosmetic results. In a standard robotic endosurgery, the palpation of tissues is performed by laparoscopic graspers located at the end effectors. The master-slave configuration in robotic surgery leads in remote access to the operation site. Therefore, surgeon’s ability to perceive valuable sensory information is severely diminished. Sensory information such as haptics, which is essential for safe …

Propagation Of Ultrasound Through Freshly Excised Human Calvarium, Armando Garcia Noguera

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

The propagation of ultrasound through complex biological media, such as the human calvarium, poses a great challenge for modern medicine. Several ultrasonic techniques commonly used for treatment and diagnosis in most of the human body are still difficult to apply to the human brain, in part, because of the properties of the skull. Moreover, an understanding of the biomechanics of transcranial ultrasound may provide needed insight into the problem of blast wave induced traumatic brain injury (TBI). In the present study, the spatial variability of ultrasonic properties was evaluated for relevant frequencies of 0.5, 1, and 2.25 MHz. A total …

Nonlinear Mechanical Behavior Of The Human Common, External And Internal Carotid Arteries In Vivo, Alexey Kamenskiy, Yuris A. Dzenis, Jason N. Mactaggart, Thomas G. Lynch, Syed A. Jaffar Kazmi, Iraklis I. Pipinos

Department of Mechanical and Materials Engineering: Faculty Publications

Introduction—The mechanical environment and properties of the carotid artery play an important role in the formation and progression of atherosclerosis in the carotid bifurcation. The purpose of this work was to measure and compare the range and variation of circumferential stress and tangent elastic moduli in the human common (CCA), external (ECA) and internal (ICA) carotid arteries over the cardiac cycle in vivo.

Methods—Measurements were performed in the surgically exposed proximal cervical CCA, distal ECA and distal ICA of normotensive patients (n = 16) undergoing carotid endarterectomy. All measurements were completed in vivo over the cardiac cycle …

Analysis Of Mechanically Milled Exchange Coupled Nanocomposite Permanent Magnets, Santanu Mukherjee

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Nanocomposite permanent magnets have recently evoked wide interest because of their interesting properties. They usually consist of a hard magnetic phase having superior coercivities and a soft magnetic phase having improved values of magnetization and when they are coupled together, we get a permanent magnet with enhanced values of both the parameters and thus can be put to a lot of applications. Also to make this possible we can take advantage of the principle of exchange interaction which has been discussed subsequently in detail.

Also the microstructure plays a major role in obtaining good magnetic properties and the microstructure is …

Finite Element Analysis Of The Implantation Of A Self-Expanding Stent: Impact Of Lesion Calcification, Shijia Zhao, Linxia Gu, Stacey R. Froemming

Department of Mechanical and Materials Engineering: Faculty Publications

In this work, the deployment of a self-expanding stent in a stenosed artery was evaluated through finite element analysis. The three-layered structure of the artery and their material properties were measured and implemented in our computational models. The instant outcomes, including lumen gain, tissue prolapse, and stress distribution, were quantified, and the effect of plaque calcification was evaluated. Results showed that the peak wall stress occurred on the media layer regardless of plaque calcification. The calcified plaque mitigated the tissue prolapse and arterial wall stresses in general, compared with the soft plaque. However, the lesion calcification led to a more …

Three-Dimensional Geometry Of The Human Carotid Artery, Alexey Kamenskiy, Jason N. Mactaggart, Iraklis I. Pipinos, Jai Bikhchandani, Yuris A. Dzenis

Department of Mechanical and Materials Engineering: Faculty Publications

Accurate characterization of carotid artery geometry is vital to our understanding of the pathogenesis of atherosclerosis. Three-dimensional computer reconstructions based on medical imaging are now ubiquitous; however, mean carotid artery geometry has not yet been comprehensively characterized. The goal of this work was to build and study such geometry based on data from 16 male patients with severe carotid artery disease. Results of computerized tomography angiography were used to analyze the cross-sectional images implementing a semiautomated segmentation algorithm. Extracted data were used to reconstruct the mean three-dimensional geometry and to determine average values and variability of bifurcation and planarity angles, …

Three-Dimensional Modeling Of Carbon/Epoxy To Titanium Single-Lap Joints With Variable Adhesive Recess Length, Yi Hua, Linxia Gu, Michael Trogdon

Department of Mechanical and Materials Engineering: Faculty Publications

The objective of this paper was to investigate the performance of recessed single-lap joints with dissimilar adherends through the finite element method. The influence of material and geometric nonlinearity of the adhesive as well as the impact of the recess length was examined in terms of maximum principal stresses. The strength of the joint was obtained as the load to initiate the crack propagation. Results suggested that either adding a spew fillet or considering the adhesive plasticity led to reduced peak stresses at the edge of the adhesive layer. The presence of a spew fillet in the single-lap joint with …

Development And Validation Of A Model For Granular Material Volume Measurements, Pourya Fasounaki

Department of Industrial and Management Systems Engineering: Dissertations, Theses, and Student Research

Keeping inventory record of packed grains in silos poses challenges since the bulk material’s different segments do not discharge uniformly, leading to formation of random peaks and valleys on the surface. To facilitate obtaining accurate volume measurement of the grains by taking into account this non-linear behavior on the surface, laser or plumb-bob level-sensing devices are employed at different part of the surface to probe the level of material under those regions.

The main goals of this research is to study the behavior of granular material in silo while discharging downward and by doing so, differentiate certain flow patterns formed …

Identification Of A Maximum Guardrail Height For The Midwest Guardrail System Using Computer Simulation, Ramen D. Julin

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

W-beam guardrails are by far the most common restraint system used along both local and major roadways. Traditionally, these restraint systems have been full-scale crash tested with a rail height ranging between 27 in. and 32 in. However, the maximum rail height which allows for safe performance of guardrails, especially in impacts involving small vehicles, has never been identified.

The main concern associated with an increase of the rail height is that small vehicles, because of their low profile, may have a tendency to lift the rail and penetrate the barrier. The objective of this project was to determine the …

Rehabilitation And Exercise Machine, Judith M. Burnfield, Yu Shu, Thad W. Buster, Carl Nelson

Department of Mechanical and Materials Engineering: Faculty Publications

An improved rehabilitation and exercise machine is provided which allows a person with physical limitations, disabilities or chronic conditions to use the machine in order to rehabilitate their muscles, improve joint flexibility, and enhance cardiovascular fitness.

Study Of Grinding Burn Using Design Of Experiments Approach And Advanced Kaizen Methodology, Kiruthika Devi Sundarrajan

Department of Industrial and Management Systems Engineering: Dissertations, Theses, and Student Research

Grinding burn has been one of the re-occurring issues at a leading automotive manufacturer. Historically when grinding burn occurred, trial and error was used to delicately find a set up process settings that provided good-enough-to-get-by results, but not optimal. Some changes include changing the coolant manifold to improve the coolant flow and rate, changing the grinding wheel, changing the type of coolant. The experiments have proved to introduce some improvements, however the occurrence of grinding burns have not been reduced or quantified and the cause of the grinding burn has not been identified or quantified. Grinding is a complex phenomenon …

Improving Health Care Quality And Safety: The Development And Assessment Of Laparoscopic Surgery Instrumentation, Practices And Procedures, Bernadette Mccrory

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Adverse events due to medical errors are a leading cause of death in the United States exceeding the mortality rates of motor vehicle accidents, breast cancer and AIDS. Improvements can and should be made to reduce the rates of preventable surgical errors since they account for nearly half of all adverse events within hospitals. Although minimally invasive surgery has proven patient benefits such as reduced postoperative pain and hospital stay, its operative environment imposes substantial physical and cognitive strain on the surgeon increasing the risk of error. In order to mitigate errors and protect patients, a multidisciplinary approach was taken …

Material Handling System For Robotic Natural Orifice Surgery, Jeff Midday

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Natural Orifice Translumenal Endoscopic Surgery (NOTES) is a relatively new surgical approach which uses no external incisions, thereby improving cosmetic outcomes, decreasing overall recovery time and reducing the risk of external infection. In standard NOTES, flexible endoscopic tools have been used to carry out a variety of surgical procedures in the abdomen. As an alternative, miniature in vivo robots can be fully inserted into the peritoneal cavity and utilized to perform various surgical procedures. These in vivo robots eliminate tool triangulation issues, improve multi-tasking capabilities and greatly increase freedom and dexterity when compared to standard endoscopic and laparoscopic tools. One …

The Integration Of Propane Flaming And Mechanical Cultivation For Effective Weed Control In Agriculture, Brian D. Neilson

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Flaming is a thermal weed control method that can kill weeds within or between crop rows using heat. Mechanical cultivation is another weed control method which undercuts weeds between crop rows to kill them. A combination flamer/cultivator implement was designed to take advantage of the good qualities of both flaming and cultivation to provide excellent organic weed control.

Flaming hoods were designed in the spring of 2010 and retrofitted on an existing row crop cultivator. The hoods were tested in corn and soybean field studies in the summer of 2010. Of the seven treatments tested, a treatment of flaming combined …

A Conductivity Testing System Coupled With A Tensile Testing Machine To Measure The Surface Properties Of Polymer Specimens, Nguyen T. Nguyen

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Polymers play an essential role in our everyday life due to their employment in a widespread range of applications. Polymers are used in industries such as space, biomedical, electronics, etc. in which their electrical and mechanical properties are major aspects which need to be investigated prior to implementation. When subjected to mechanical stimulations, polymers may exhibit changes in electrical conductivity which can vary locally within the specimens, especially in those of conducting polymers. In mechanical investigations a tensile testing machine is used to understand polymers’ strength, elasticity or other mechanical properties. In electrical analysis, using a four-point probe to examine …

Effects Of Approach Techniques In Place Kicking: A 3d Analysis, Chase M. Pfeifer

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Various studies aim to understand the fundamentals of kicking, primarily the instep kick commonly used by soccer players. Of those studies, most are limited to a 2D analysis using high-speed cameras for position tracking and electromyography to observe muscle activity. The few studies that investigate a 3D model are limited in their position tracking capabilities and focus mainly on joint flexion potentials and foot speed. To the authors knowledge no study of this caliber has been performed on the kinematics and dynamics of place kicking in American football. This thesis uses a 12 camera high-speed motion tracking system to investigate …

Model-Based Systems And Methods For Analyzing And Predicting Outcomes Of Vascular Interventions And Reconstructions, Yuris A. Dzenis, Alexey Kamenskiy, Iraklis I. Pipinos, Jason N. Mactaggart

Department of Mechanical and Materials Engineering: Faculty Publications

Systems and methods for analyzing and predicting treatment outcomes of medical procedures such as vascular interventions and reconstructions are disclosed. An illustrative system for analyzing and predicting therapeutic outcomes of medical procedures comprises a relational database configured for classifying and storing patient specific input data for multiple patients, a fluid-solid interaction biomechanical model configured for performing a biomechanics simulation and generating biomechanics data, and a graphical user interface.

Microstructure Selection Of Sm–Co–Al Alloys To Increase Magnetization, Brian Dick

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

An ever increasing demand for higher performing magnets drives the need for new and innovative methods to achieve this goal. Sm-Co rare earth permanent magnets have a unique eutectic microstructure that, through refinement, could become a two-phase magnet which would significantly increase their energy product. The eutectic structure of Sm₈Co₉₂ is comprised of αCo rods embedded within a Sm₂Co₁₇ matrix. If the rods are small enough to encourage exchange coupling and the matrix is smaller than the single domain limit, then an efficient two-phase magnet is created.

Refining the Co rods and matrix size …

Error Reduction And Effect Of Step Size In Adjustment Calculus For Cam Applications, Sai Siddhartha Nudurupati

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Any measurement, however carefully done, will never be free from errors. Similarly, machining of cams for automobiles is prone to contain errors. These errors are naturally a part and parcel of cam manufacturing. The nature of deviations of the manufactured cam profile from the theoretical cam determines its usability. Sometimes, allowable deviations in high speed cams may be in the order of 2540 µm. Larger deviations will disqualify the cams for applications.

Velocity and acceleration of the cam are estimated from the measured displacement of the cam follower during quality control implementation. This data helps in eliminating the unfit cams. …

Development And Recommendations For A Non-Proprietary, High-Tension, Cable End Terminal System, Ryan J. Terpsma

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Cable guardrail systems have been increasing in popularity in recent years due to several perceived benefits over the commonly used W-beam guardrail. A non-proprietary design was desired as an alternative to the many proprietary designs available. A non-proprietary, high-tension cable end terminal was necessary to accompany the non-proprietary, high-tension cable guardrail system under development.

The objective of this research project was to develop design recommendations for a non-proprietary, high-tension cable end terminal. An analysis of several cable guardrail end terminals was undertaken to identify any common features that may prove to be beneficial or detrimental to end terminal designs. Next, …

Peridynamic Models For Dynamic Brittle Fracture, Wenke Hu

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Damage and failure in composite materials under dynamic loading has been extensively studied in experiments for several decades. Composite materials exhibit various damage and failure patterns under different loading rates, such as splitting and branching. Classical models cannot directly be applied to problems with discontinuous fields. A new nonlocal continuum model, peridynamics, has been proposed with the goal of solving dynamic fracture problems.

The J-integral has the physical significance of energy flow into the crack tip region. We present a rigorous derivation for the formulation of the J-integral in peridynamics using the crack infinitesimal virtual extension approach. We …

Effects Of Mismatched Electrodes On An At-Cut Quartz Resonator, Huijing He, Jinxi Liu, Jiashi Yang

Department of Mechanical and Materials Engineering: Faculty Publications

We study thickness-shear and thickness-twist free vibrations of a finite AT-cut quartz resonator with mismatched electrodes. The equations of anisotropic elasticity are used with the omission of the small elastic constant c56. An analytical solution is obtained using Fourier series from which the resonant frequencies, mode shapes, and vibration confinement resulting from the electrode inertia are calculated and examined.

Nebraska Summary: S861 New Holland T6 175, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S901 Massey Ferguson 7620, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Mountain Bike Wheel Endurance Testing And Modeling, Robin C. Redfield, Cory Sutela

United States Air Force: Publications

Mountain bike wheels may be evaluated for durability and mode of failure using bump drum test machines that subject wheels to simulated rider loads and uneven terrain. These machines may operate at high speeds in order to accelerate failures, particularly during the design and prototype phase of wheel development. This paper describes a mathematical model of the dynamics of a wheel test drum assembly, and the validation of the model using data recorded during a wheel test. This model will subsequently be applied to better understand the key test operating parameters that must be controlled in order to produce repeatable …

Numerical Simulation Of Buoyancy-Driven Turbulent Ventilation In Attic Space Under Winter Conditions, Shimin Wang, Zhigang Shen, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

Attic design and construction have significant impacts on residential buildings’ energy performance. In order to understand how passive ventilation rates affect ridge-vent attic’s performance, a two-dimensional steady-state finite volume model is employed to simulate the buoyancy-driven turbulent ventilation and heat transfer in a triangular attic space of a gable-roof residential building under winter conditions. The modeled attic has a pitch of 5/12 and a passive ventilation system, consisting of continuous ridge and soffit vents. The v2f model is used to analyze the turbulent air flow and natural convection heat transfer inside the attic. The effects of ambient air temperature, vent …