Mechanical Engineering Commons^™

Nebraska Summary: S911 Massey Ferguson 7616, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2077: John Deere 6115m, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2076: John Deere 6105m, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2075: John Deere 5100e, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2074: John Deere 5085e, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2066: Versatile 375, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2054a: Case Ih Farmall 75c, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Binaural Room Impulse Response Database Acquired From A Variable Acoustics Classroom, Zhao Peng, Siu Kit Lau, Lily M. Wang, Sean Browne, Kenneth P. Roy

Durham School of Architectural Engineering and Construction: Faculty Publications

Room measurements were conducted in a variable acoustics classroom mockup space (epod) at Armstrong World Industries in Lancaster, Pennsylvania, USA. Binaural room impulse responses were measured in the epod using a head and torso simulator. Five reverberation time (RT) scenarios were achieved with various combinations of absorptive wall panels and acoustical ceiling tile. These provided a range of mid-frequency RTs from 0.4 to 1.1 seconds. Three of the five RT scenarios were achieved using two different material configurations to also consider material location effects. For each of the eight material configurations, two student-teacher orientations were tested. One orientation had all …

Nebraska Summary: S952 New Holland T5.95, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S946 New Holland T4.95, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Nebraska Summary: S919 Challenger Mt475d, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2073: Case Ih Steiger 500 Quadtrac, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2061: Challenger Mt755d, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Solution-Processed Nanoparticle Super-Float-Gated Organic Field-Effect Transistor As Un-Cooled Ultraviolet And Infrared Photon Counter, Yongbo Yuan, Qingfeng Dong, Bin Yang, Fawen Guo, Qi Zhang, Ming Han, Jinsong Huang

Department of Mechanical and Materials Engineering: Faculty Publications

High sensitivity photodetectors in ultraviolet (UV) and infrared (IR) range have broad civilian and military applications. Here we report on an un-cooled solution-processed UV-IR photon counter based on modified organic field-effect transistors. This type of UV detectors have light absorbing zinc oxide nanoparticles (NPs) sandwiched between two gate dielectric layers as a floating gate. The photon-generated charges on the floating gate cause high resistance regions in the transistor channel and tune the source-drain output current. This ‘‘super-float-gating’’ mechanism enables very high sensitivity photodetectors with a minimum detectable ultraviolet light intensity of 2.6 photons/µm²s at room temperature as well …

Analysis Of Electrically-Forced Vibrations Of Piezoelectric Mesa Resonators, Huijing He, Guo-Quan Nie, Jin-Xi Liu, Jiashi Yang

Department of Mechanical and Materials Engineering: Faculty Publications

We study the electrically forced thickness-shear and thickness-twist vibrations of stepped thickness piezoelectric plate mesa resonators made of polarized ceramics or 6-mm class crystals. A theoretical analysis based on the theory of piezoelectricity is performed, and an analytical solution is obtained using the trigonometric series. The electrical admittance, resonant frequencies, and mode shapes are calculated, and strong energy trapping of the modes is observed. Their dependence on the geometric parameters of the resonator is also examined.

Review Of Electrochemical And Electrodischarge Machining, Kamlakar P. Rajurkar, M. M. Sundaram, A. P. Malshe

Department of Mechanical and Materials Engineering: Faculty Publications

Electrochemical and electro-discharge machining processes are the two major electro-machining processes with unique capabilities. Electrical Discharge Machining (EDM) and Electrochemical Machining (ECM) offer a better alternative or sometimes the only alternative in generating accurate 3-D complex shaped macro, micro and nano features and components of difficult–to-machine materials. Technological advances reported in electrochemical and electro discharge machining processes, which reflect the state of the art in academic and industrial research and applications, are briefly reviewed in this paper.

Wire Electro-Discharge Machining Of Titanium Alloy, Farnaz Nourbakhsh, Kamlakar P. Rajurkar, Ajay P. Malshe, Jian Cao

Department of Mechanical and Materials Engineering: Faculty Publications

This paper presents an experimental investigation of wire electro-discharge machining (WEDM) of titanium alloy. The objective is to investigate the effect of seven process parameters including pulse width, servo reference voltage, pulse current, and wire tension on process performance parameters (such as cutting speed, wire rupture and surface integrity). A Taguchi L18 design of experiment (DOE) has been applied. All experiments have been conducted using Charmilles WEDM. It was also found that the cutting speed increases with peak current and pulse interval. Surface roughness was found to increase with pulse width and decrease with pulse interval. The Analysis of Variance …

Selective Detection And Automated Counting Of Fluorescently-Labeled Chrysotile Asbestos Using A Dual-Mode High-Throughput Microscopy (Dm-Htm) Method, Myoung-Ock Cho, Hyo Mi Chang, Donghee Lee, Yeon Gyu Yu, Hwataik Han, Jung Kyung Kim

Department of Mechanical and Materials Engineering: Faculty Publications

Phase contrast microscopy (PCM) is a widely used analytical method for airborne asbestos, but it is unable to distinguish asbestos from non-asbestos fibers and requires time-consuming and laborious manual counting of fibers. Previously, we developed a high-throughput microscopy (HTM) method that could greatly reduce human intervention and analysis time through automated image acquisition and counting of fibers. In this study, we designed a dual-mode HTM (DM-HTM) device for the combined reflection and fluorescence imaging of asbestos, and automated a series of built-in image processing commands of ImageJ software to test its capabilities. We used DksA, a chrysotile-adhesive protein, for selective …

Photovoltaic Device, Jinsong Huang, Bin Yang, Yongbo Yuan

Department of Mechanical and Materials Engineering: Faculty Publications

An apparatus includes a substrate; and a photoactive layer disposed on the substrate. The photoactive layer includes an electron acceptor material; an electron donor material; and a material having dipoles.

Testing The Fuel Efficiency Of Tractors With Continuously Variable And Standard Geared Transmissions, Christopher N. Howard, Michael F. Kocher, Roger M. Hoy, Erin E. Blankenship

Department of Agricultural and Biological Systems Engineering: Faculty Publications

A John Deere 8295R IVT tractor with a continuously variable transmission (CVT) and a John Deere 8295R PowerShift (PST) tractor with a standard geared transmission (GT) were tested for fuel consumption at three different travel speeds with six different load levels applied per speed. The JD 8295R PST tractor was tested both at full throttle (FT) and shifted up two gears and throttled back (SUTB) to achieve the same travel speed as at full throttle. For each travel speed with each transmission mode, fuel consumption was determined to be linearly related to drawbar power. Linear regression analyses were performed, and …

Energy Trapping Of Thickness-Shear And Thickness-Twist Modes In A Partially Electroded At-Cut Quartz Resonator, Huijing He, Guoquan Nie, Jinxi Liu, Jiashi Yang

Department of Mechanical and Materials Engineering: Faculty Publications

The thickness-shear and thickness-twist vibrations of a finite and partially electroded AT-cut quartz resonator are investigated. The equations of anisotropic elasticity are used with the omission of the small elastic constant c56 . An analytical solution is obtained using Fourier series from which the free vibration resonant frequencies, mode shapes, and energy trapping are calculated and examined.

Sustainability For Die Manufacturing: Comparative Study Of Wedm And Milling, Matthew S. Kalus

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Sustainability is more important in today's culture due to the increasing demand for a more eco-friendly society. Concentrations in minimizing and reducing environmental impacts, energy and natural resources have been forthcoming in industry. The tool, mold and die industries are the most well known industries that machine harder materials using mills and WEDM. The objective of this thesis was to compare the sustainability differences in both of these machines utilizing the accepted standards for evaluating the manufacturing process performance for sustainability. These standards include the evaluation of the process parameters, raw materials, power, tools and fluids which all contribute to …

Implementation Of Magnetic Resonance Elastography For The Investigation Of Traumatic Brain Injuries, Thomas Boulet

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Magnetic resonance elastography (MRE) is a potentially transformative imaging modality allowing local and non-invasive measurement of biological tissue mechanical properties. It uses a specific phase contrast MR pulse sequence to measure induced vibratory motion in soft material, from which material properties can be estimated. Compared to other imaging techniques, MRE is able to detect tissue pathology at early stages by quantifying the changes in tissue stiffness associated with diseases. In an effort to develop the technique and improve its capabilities, two inversion algorithms were written to evaluate viscoelastic properties from the measured displacements fields. The first one was based on …

A Study Of Hdpe In High Pressure Of Hydrogen Gas: Measurement Of Permeation Parameters And Fracture Criteria, Sompong Prachumchon

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The permeation parameters of hydrogen gas in high density polyethylene (HDPE) system are sought by comparison with a diffusion model. The method of Green’s functions is used to obtain solutions for the diffusion model. Permeation parameters are found from transient experimented data during two processes; pressurization followed by depressurization. The mechanical compression of HDPE during the pressurization process resulted in lower diffusivity coefficient values and higher solubility values. The results show that the diffusivity coefficient value in the pressurization process is 37% of that during the depressurization process. At the start of the depressurization process, a short-duration fast flow rate …

Cable Median Barrier Failure Analysis And Remediation, Cody S.. Stolle

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

On divided roadways, cross-median fatalities are disproportionately overrepresented in fatal and serious injury crashes. Many state DOTs sought to mitigate cross-median crash risk by installing cable median barriers. Despite increased crash rates, studies evaluating crash rates before and after cable median barriers were installed indicated excellent improvement in overall safety.

Although cable median barriers are intended to prevent serious cross-median crashes, cable barriers can also contribute to serious injury and fatality crashes which would not have otherwise occurred, including penetration and rollover crashes. In order to reduce the frequency of undesirable penetration and rollover crashes occurring with cable median barriers …

Predicting Vehicle Dynamics For Roadside Safety Using Multibody Systems Simulations, Brett D. Schlueter

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Accurate means for predicting vehicle dynamics is required in the design and testing of roadside safety hardware. Past research has used finite element (FE) modeling to this end, but multibody systems (MBS) modeling may provide a more efficient way to solve these problems. MBS modeling using Adams/Car was investigated by first compiling an introduction to the program, then performing basic vehicle dynamics simulations using a supplied model. Next, a model of a 2270 kg pickup was created and validated against physical test data involving impact with a speed bump. Finally, pickup trajectories in 4H:1V and 6H:1V V-ditches were predicted for …

Modular Joystick Design For Virtual Reality Surgical Skills Training, Michael Head

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

A modular control interface and simulated virtual reality environment was designed and created in order to determine how the kinematic architecture of a control interface affects minimally invasive surgery. A user is able to selectively determine how many, the type, and location of degrees of freedom they require for the specific surgical simulation through the use of modular joints and constraint components. Furthermore, passive locking was designed and implemented through the use of inflated latex tubing around rotational degree of freedom joints. It is believed these features will have the ability to effectively simulate a variety of surgical simulations and …

Maximal Force Characteristics Of The Ca2+-Powered Actuator Of Vorticella Convallaria, Sangjin Ryu, Matthew J. Lang, Paul Matsudaira

Department of Mechanical and Materials Engineering: Faculty Publications

The millisecond stalk contraction of the sessile ciliate Vorticella convallaria is powered by energy from Ca²⁺ binding to generate contractile forces of ~10 nN. Its contractile organelle, the spasmoneme, generates higher contractile force under increased stall resistances. By applying viscous drag force to contracting V. convallaria in a microfluidic channel, we observed that the mechanical force and work of the spasmoneme depended on the stalk length, i.e., the maximum tension (150–350 nN) and work linearly depended on the stalk length (~2.5 nN and ~30 fJ per 1 mm of the stalk). This stalk-length dependency suggests that motor units of …

Optimal Reduction Of Electrical Energy Consumption By Supply Air Ac Motors, Keyhan Rafiee

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The Nebraska Center for Energy Sciences Research (NCER) at the University of Nebraska-Lincoln (UNL) strives to be energy efficient through Green Energy. Of course, in meeting some of the requirements for different types of Leadership in Energy and Environmental Design (LEED) certification, certain minimum levels of energy efficiency practices must be met. One such level of energy efficiency, in particular, is reduction in the consumption of electrical energy in buildings. This thesis is a study of methods of reducing the consumption of electrical energy (measured in kW of electrical power) in the UNL Jorgensen Hall (JH) air handling unit 2 …

Fabrication And Characterization Of Biocomposites From Polylactic Acid And Bamboo Fibers, Sarah E. Royse

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Environmental concerns have been motivating research in the field of biodegradable materials, especially those from biological sources. Polylactic acid (PLA) is one biopolymer with the potential to replace some standard synthetic polymers. PLA is currently used for fibers, medical sutures, and some packaging, but is still used very little compared with synthetic polymers. One thing that can be done to expand the potential applications of PLA is to add fibers to create composite materials. Bamboo is a good choice for these fibers because it is abundant in many parts of the world, grows very quickly, and is widely unused. Composites …