Mechanical Engineering Commons^™

Impinging Jet Spray Formation Using Non-Newtonian Liquids, Neil S. Rodrigues

Open Access Theses

Over the past two decades there has been a heightened interest in implementing gelled propellants for rocket propulsion, especially for hypergolic bi-propellants such as monomethylhydrazine (MMH) and nitrogen tetroxide oxidizer (NTO). Due to the very high level of toxicity of hypergolic liquid rocket propellants, increasing safety is an important area of need for continued space exploration and defense operations. Gelled propellants provide an attractive solution to meeting the requirements for safety, while also potentially improving performance. ^ A gelling agent can be added to liquid propellants exhibiting Newtonian behavior to transform the liquid into a non-Newtonian fluid with some solid-like …

Design Of A High Performance Actuation System Enabled By Energy Coupling Actuation, Daniel Richard Skelton

Open Access Theses

The main goal of the research was to design, manufacture, and test a new linear actuation system. Research was conducted on several types of actuation methods applied to hydraulic valves. A literature review showed that most existing actuator systems have the actuator and control mass coupled together. There is a need for high speed actuation. The proposed idea is to have the actuation mass always moving while accelerating and decelerating the control mass. The decoupling of these two will allow for the actuation and control mechanism to be independent and only move the control mechanism when needed. Initial modeling, as …

Development, Numerical Demonstration And Experimental Verification Of A Method For Model Updating Of Boundary Conditions, Christian Eduardo Silva Salazar

Open Access Theses

The study of vibrations in beams has been largely addressed by authors and researchers. However, relatively few researchers have considered the case of unknown boundary conditions, as usually it is reasonable to assume the classical cases such as simply supported, clamped or free. Indeed, there are a wide variety of boundary-condition configurations, each one representing a whole different problem with its own modal characteristics. ^ A method for updating experimental beam models to specifically address the issue of unknown boundary conditions is proposed. This methodology takes advantage of vector comparison techniques such as the modal assurance criterion and the dot …

The Prediction Of Airborne And Structure-Borne Noise Potential For A Tire, Nicholas Sakamoto

Open Access Theses

Tire/pavement interaction noise is a major component of both exterior pass-by noise and vehicle interior noise. The current testing methods for ranking tires from loud to quiet require expensive equipment, multiple tires, and/or long experimental set-up and run times. If a laboratory based off-vehicle test could be used to identify the airborne and structure-borne potential of a tire from its dynamic characteristics, a relative ranking of a large group of tires could be performed at relatively modest expense. This would provide a smaller sample set of tires for follow-up testing and thus save expense for automobile OEMs. The focus of …

Design And Development Of A Novel Test Method To Measure The Slipper / Swashplate Interface Fluid Film In A Positive Displacement Machine, Natalie A. Spencer

Open Access Theses

Although robust models of fluid film behavior between the slipper / swashplate lubricating interface in positive displacement machines have been developed, measuring this same fluid film thickness to a highly accurate degree inside a relatively unaltered axial piston unit has never been accomplished until now. A test method was created to close this gap in available data by measuring fluid film thickness between the slipper and swashplate in a 130cc axial piston pump. Precise knowledge of the gap height between the slipper and swashplate at various shaft angle locations during operation provides critical insight into machine behavior. The design, validation, …

A Numerical Procedure To Design The Optimal Axial Balance In External Gear Machines And Its Potential In Formulating Novel Efficient Design Solutions, Divya Thiagarajan

Open Access Theses

A novel numerical procedure to design the optimal axial balance in external gear machines (EGMs) has been formulated and developed in the present study. Lateral lubricating interfaces exist between the lateral bushes and the rotating gears in pressure compensated designs of EGMs and play a significant role in minimizing power losses arising from fluid shear stress and leakages from the gap. Moreover, lateral bushes in pressure compensated designs of EGMs perform significant functions of sealing the tooth space volumes while they transfer fluid from the inlet to the outlet port. ^ The losses from the lateral gap from these two …

A Web-Based Online Collaboration Platform For Formulating Engineering Design Projects, Sainath Varikuti

Open Access Theses

Effective communication and collaboration among students, faculty and industrial sponsors play a vital role while formulating and solving engineering design projects. With the advent in the web technology, online platforms and systems have been proposed to facilitate interactions and collaboration among different stakeholders in the context of senior design projects. However, there are noticeable gaps in the literature with respect to understanding the effects of online collaboration platforms for formulating engineering design projects. Most of the existing literature is focused on exploring the utility of online platforms on activities after the problem is defined and teams are formed. Also, there …

Optical Direct-Write Nanolithography Based On Self-Assembled Resist, Meghana Akella

Open Access Theses

Holographic display is being developed for next generation mobile phones. However, manufacturing of miniature gratings for the holographic projectors cost a few thousand dollars today, not making the concept practical for commercial purposes. In this thesis, we discuss the feasibility of self-assembled nanoparticles to manufacture holographic gratings cost-effectively and at the nanoscale. Using our approach, the gratings can be manufactured at the scale of 20nm and the cost per chip is expected to cost a few dollars.^ In this thesis, a hydrophobic SAM was used to modify the surface of silicon. Direct-write UV laser lithography was used for photothermal patterning …

Transverse Compression Of High-Performance Ballistic Fibers, Zherui Guo

Open Access Theses

High performance ballistic fibers have been in use for decades, specifically in protective applications against ballistic impact such as bulletproof vest layers and aircraft turbine engine fragmentation barriers. These high performance fibers have extremely high strength-to-weight ratios and high moduli of elasticity in the axial direction, making them extremely suitable for high impact situations. In particular, para-phenyleneterephthalamide (PPTA for short) fibers such as Kevlar^® and ultra-high-molecular-weight polyethylene fibers such as Dyneema^® are amongst the more popular high performance fibers in today's world. While the longitudinal mechanical response of these fibers have been extensively researched, their transverse mechanical response …

Cylinder Block / Valve Plate Interface Performance Investigation Through The Introduction Of Micro-Surface Shaping, Rene Chacon Portillo

Open Access Theses

Swash plate type axial piston machines are widely used positive displacement machines in different fields of industry ranging from aerospace, agriculture, automotive, heavy machinery, etc. Lubricating gaps are the main source of energy dissipation in axial piston machines. This type of machines have three lubricating interfaces: slipper/swash plate interface, piston cylinder and the cylinder block/valve plate interface. The cylinder block/valve plate interface being one of the most critical design elements of the machine. Extensive research has been done at Maha Fluid Power Research Center in Purdue University both to model this interface and to study the effects of micro-surface shaping …

Design, Development And Testing Of A Balance Board With Variable Torsional Stiffness And Time Delay, Denise Renee Cruise

Open Access Theses

The ability to balance and maintain upright posture can decline for a variety of reasons, such as aging and neuromuscular impairment. As the ability to balance declines, the risk of falling increases. Falls are a major cause of injury, and often lead to a dramatic decline in quality of life. Currently, to alleviate balance deficiencies, people participate in balance training, which most commonly refers to standing on an unstable balance board; the most common boards used are either passive wobble boards, or more advanced commercial systems such as the Biodex System SD ® or the Neurocom SMART Balance Master® . …

Laboratory Apparatus For Gas Turbine Combustion Development, Dustin Lee Cruise

Open Access Theses

The next generation of combustor technology will be required to meet the demands of a world more focused on greenhouse gases and global warming. Due to this new focus on emission control, combustors must produce less NO x , while operating in a higher pressure environment that is more prone to combustion instabilities.

This work focuses on the development of a lab and combustor that will be used for the next generation combustor development. The lab development includes layout and organization, facilities, measurement and instrumentation, automation of the testing process, and an imaging tool for diagnostics.

A Lean Direction Injection …

Design Of Optical Access For The Application Of Laser Doppler Velocimetry In A Low Specific Speed Centrifugal Compressor, Bryce Ashton Heckaman

Open Access Theses

The objective of this research has been to design optical access for the application of laser Doppler velocimetry (LDV) in a low specific speed centrifugal compressor. The ability to acquire non-intrusive flow measurements will provide valuable insight into tip leakage flow, secondary flow, and impeller/diffuser interactions within the centrifugal compressor. The current research facility houses a new low specific speed centrifugal compressor which design is based off a compressor that would be installed as the last stage of a high-pressure compressor.

The LDV optical access has been designed and includes two fused silica windows that are housed in stainless steel …

Optimal Control Of Unknown Nonlinear System From Inputoutput Data, Xin Jin

Open Access Theses

Optimal control designers usually require a plant model to design a controller. The problem is the controller's performance heavily depends on the accuracy of the plant model. However, in many situations, it is very time-consuming to implement the system identification procedure and an accurate structure of a plant model is very difficult to obtain. On the other hand, neuro-fuzzy models with product inference engine, singleton fuzzifier, center average defuzzifier, and Gaussian membership functions can be easily trained by many well-established learning algorithms based on given input-output data pairs. Therefore, this kind of model is used in the current optimal controller …

High Temperature Flooded Expansion For Solar Thermal Power Generation, Nelson Alexander James

Open Access Theses

Even though solar power usage has seen rapid growth over the past decade, fossil fuel generation sources are still generally a less expensive means of producing power. The Liquid-Flooded Ericsson Cycle (LFEC) was investigated as a high efficiency power cycle for reducing the cost of concentrated solar power (CSP) plants and helping to address this cost disparity. High temperature flooded expansion was identified as one of the main challenges in regards to utilizing the LFEC as a power cycle. Thermodynamic models were developed to help assess the performance of the LFEC and a load stand was constructed to test a …

Integration And Implementation Of High-Voltage Energy Storage Sub-System For A Parallel-Through-The-Road Plug-In Hybrid Electric Vehicle, Bilwa A. Jadhav

Open Access Theses

With research showing an alarming rate of increase in global warming and thus causing dangerous instabilities in the weather, a strong push has been initiated to reduce greenhouse gas emissions. Transportation being one of the top offenders in greenhouse gas emissions, has led the drive for improving the efficiency of the modern automobile. One of the current strategies for reducing the emissions produced by the transportation sector is hybrid vehicles powered from both a fuel such as gasoline, diesel, or hydrogen; and electricity. This merger has proven to be effective at decreasing harmful emissions including, carbon dioxide (CO 2 ) …

Fundamental Design Principles Of Novel Mems Based "Landau" Switches, Sensors, And Actuators : Role Of Electrode Geometry And Operation Regime, Ankit Jain

Open Access Dissertations

Microelectromechanical systems (MEMS) are considered as potential candidates for "More-Moore" and "More-than-Moore" applications due to their versatile use as sensors, switches, and actuators. Examples include accelerometers for sensing, RF-MEMS capacitive switches in communication, suspended-gate (SG) FETs in computation, and deformable mirrors in optics. In spite of the wide range of applications of MEMS in diverse fields, one of the major challenges for MEMS is their instability. Instability divides the operation into stable and unstable regimes and poses fundamental challenges for several applications. For example: Tuning range of deformable mirrors is fundamentally limited by pull-in instability, RF-MEMS capacitive switches suffer from …

High Fidelity Simulations Of Electrokinetic Phenomena In Microfluidic Devices, Qian Li

Open Access Dissertations

Electroosmotic flow with electrokinetic effects is the primary method of fluid handling in micro-total analysis systems. Under external applied electric fields, electrokinetic micro-devices allow for innovative functionality in a wide range of microfluidic applications including sample injection, separation, rapid micromixing, and miniaturized chemical and biochemical analysis and detection. This dissertation focuses on simulations of two electrokinetic phenomena, isotachophoresis (ITP) and electrokinetic instability (EKI). A set of coupled governing equations including the incompressible Naiver-Stokes equations, Nernst-Planck transport equations and a charge conservation equation are solved in the simulation. A multiblock in-house solver based on high-order finite difference schemes is developed to …

Novel Energy Efficient Electrohydraulic Steer-By-Wire Technology, Naseem Daher

Open Access Dissertations

Improving energy efficiency, productivity, safety, and comfort of mobile machines is of utmost priority to original equipment manufacturers, suppliers, and consumers given the escalating fuel prices and increased awareness to the environment and workplace hazards. A major breakthrough in the realm of high power motion control is pump displacement controlled (DC) actuation, which does away with hydraulic valves for motion control and uses a variable displacement pump as both a flow source and final control element, thus eliminating throttling losses associated with hydraulic control valves. This work deals with researching and implementing DC technology for realizing the steering function of …

Autonomous Indoor Localization For Fire Safety And Resource Location Via Field Mapping Techniques, Jaeyoung Kim, Kartik Ariyur, Yan Cui, Benjamin D. Branch, Joshua Ebung Umo

Libraries Faculty and Staff Presentations

An overall result of this collaboration between the Mechanical Engineering Dept. and the Purdue University Libraries (PUL) should result in building a big data framework that make have knowledge transfer for similar large scale geospatial data implementations. Such may promote best practices of data management where the library skill sets may aid faculty research and student learning. Here, the PUL is concerned with advancing the Mechanical Engineering‘s STEM pipeline capacity with this type of research, collaboration and data management engagement.

Autonomous Indoor Localization For Fire Safety And Resource Location Via Field Mapping Techniques (Android Version), Joshua Ebung Umo, Yan Cui, Kartik Ariyur, Benjamin D. Branch, Jaeyoung Kim

Libraries Faculty and Staff Presentations

An overall result of this collaboration between the Mechanical Engineering Dept. and the Purdue University Libraries (PUL) should result in building a big data framework that make have knowledge transfer for similar large scale geospatial data implementations. Such may promote best practices of data management where the library skill sets may aid faculty research and student learning. Here, the PUL is concerned with advancing the Mechanical Engineering‘s STEM pipeline capacity with this type of research, collaboration and data management engagement.

Phase Field Modeling Of Shear Yielding And Crazing In Glassy Polymer, Yunzhe Mao

Open Access Theses

Glassy polymers are very important in industrial and commercial components manufacturing. For instance, it is used to manufacture polymer-matrix composites, the type of composite used in the Dreamliner 787. But this kind of material is also limited by its tendency to fail in brittle manner. In this study, we use phase field model to characterize the yielding condition of glassy amorphous polymer under a wide range of loading conditions. The main failure mechanisms in amorphous glassy polymers, such as poly-methyl-methacrylate (PMMA), are crazing and shear yielding. Crazing is formed because of the nucleation of micro-voids in the location of stress …

Particle Deposition On Superhydrophobic Surfaces By Sessile Droplet Evaporation, Mercy G. Dicuangco

Open Access Theses

Prediction and active control of the spatial distribution of particulate deposits obtained from sessile droplet evaporation is essential in ink-jet printing, nanostructure assembly, biotechnology, and other applications that require localized deposits. In recent years, sessile droplet evaporation on bio-inspired superhydrophobic surfaces has become an attractive method for depositing materials on a site-specific, localized region, but is less explored compared to evaporative deposition on hydrophilic surfaces. It is therefore of interest to understand particle deposition during droplet evaporation on superhydrophobic surfaces to enable accurate prediction and tunable control of localized deposits on such surfaces. The purpose of the present work is …

Study Of Aluminum Honeycomb Sandwich Composite Structure For Increased Specific Damping, Aditi S. Joshi

Open Access Theses

The aluminum honeycomb sandwich composite structure is commonly used in the aerospace and automotive applications where high strength to weight ratio is desirable. However the poor performance of the aluminum honeycomb sandwich composite structure in terms of the vibration damping and the sound transmission makes their applications limited. Studying the effect of different structural modifications on the damping has become an interesting area of research in past few decades. The present study addresses the effect of adding a mass on the composite beam at various locations on the damping loss factors for the modes of vibration present in the frequency …

Experimental Investigation Of A Forced Response Condition In A Multistage Compressor, William Louis Murray

Open Access Theses

The objective of this research is twofold. Firstly, the design, development, and construction of a test facility for a Honeywell APU-style centrifugal compressor was implemented, as well as the design and construction of an inlet flow experiment. Secondly, the aeromechanical response of an embedded stage in the Purdue 3-Stage axial research compressor was analyzed through a suite of different measurement techniques in the fulfillment of the end of the GUIde IV Consortium contract. ^ The purpose of the first phase of Honeywell work was to comprehensively measure the flow field of an APU-style centrifugal compressor inlet through the use of …

Unsteady Forces On A Spherical Particle Accelerating Or Decelerating In An Initially Stagnant Fluid, Yashas Mudlapur Phaneesh Keshav

Open Access Theses

Flows with particles play an important role in a number of engineering applications. These include trajectories of droplets in sprays in fuel-injected-reciprocating-piston and gas-turbine engines, erosion of materials due to particle impact on a surface, and deposition of materials on surfaces by impinging droplets or particles that could solidify or bond on impact. For these applications, it is important to understand the forces that act on the particles so that their trajectories could be predicted.

Considerable work has been done on understanding the forces acting on spherical particles, where the Reynolds numbers (Rep ) based on the particle …

Probabilistic Fault Detection And Diagnostics For Packaged Air-Conditioner Outdoor-Air Economizers, Andrew L. Hjortland

Open Access Theses

Poor economizer control, economizer damper failure, and excess outdoor-air contribute to these performance degradations. In order to promote optimal rooftop air-conditioner (RTU) performance and reduce operating costs, an automated fault detection and diagnostics (AFDD) tool has been designed for RTUs with integrated economizers. Based on previously proposed methods, the proposed method advances the economizer fault detection and diagnosis components by using statistical classifiers in order to provide more robust, probabilistic fault outputs. A set of air-side virtual sensors has also been added to the method in order to expand the applicable range of conditions fault detection and diagnostics can be …

Quantitative Imaging Of Radiation Intensity From A Turbulent Sooting Flame, Robert Kapaku

Open Access Theses

Quantitative imaging of radiation intensity (QIRI) is a method of investigating temporally and spatially resolved radiation from species and particulates in turbulent flames. The current study reports quantitative images of radiation intensity from a turbulent ethylene flame that matches the Reynolds number (15,200) of a non-sooting flame from the International Workshop on Measurement and Computation of Turbulent Non-premixed Flames. A calibrated high-speed infrared camera with four band-pass filters was used to acquire images of radiation intensity in wavelengths corresponding to carbon dioxide, water vapor, and soot. The luminous flame measurements show thin radiating structures corresponding to soot layers and higher …

An Algorithm For Impacting Soft Structures, Tengfei Long

Open Access Theses

Impact among soft structures is often difficult to model because of the geometrical non-linearity involved. There are a number of previous studies of the contact dynamics of rigid bodies, but few has focused on soft structures so far.

This thesis models impact between soft structures without any restraint on their geometries. The goal is to simulate the dynamics involved among soft structures during an impact process. This has been done through designing and implementing an contact algorithm that uses the finite element method along with a three-dimensional solid element to solve the fundamental time integration problem. Modeling of the contact …

Experimental And Numerical Study Of The Air Distribution In An Airliner Cabin, Wei Liu

Open Access Theses

Nowadays, more people, including those with impaired health or who are otherwise potentially sensitive to the cabin environment, are traveling by air than ever before. The flying public demands a higher comfort level and a cleaner environment because they encounter a combination of environmental factors including low humidity, low air pressure, and sometimes, exposure to air contaminants such as ozone, carbon monoxide, various organic chemicals, and biological agents. Moreover, international air travel has increased the potential risks associated with airborne disease transmission and the release, whether accidentally or intentionally, of noxious substances during flight. Many studies suggest that the risk …