Mechanical Engineering Commons^™

Nanomechanics Of Cellulose Crystals And Cellulose-Based Polymer Composites, Anahita Pakzad

Dissertations, Master's Theses and Master's Reports - Open

Cellulose-polymer composites have potential applications in aerospace and transportation areas where lightweight materials with high mechanical properties are needed. In addition, these economical and biodegradable composites have been shown to be useful as polymer electrolytes, packaging structures, optoelectronic devices, and medical implants such as wound dressing and bone scaffolds.

In spite of the above mentioned advantages and potential applications, due to the difficulties associated with synthesis and processing techniques, application of cellulose crystals (micro and nano sized) for preparation of new composite systems is limited. Cellulose is hydrophilic and polar as opposed to most of common thermoplastics, which are non-polar. …

Numerical Modeling Of The Failure Mechanisms In Si Thin Film Anode For Li-Ion Batteries, Siddharth H. Patel

Dissertations, Master's Theses and Master's Reports - Open

In recent times, the demand for the storage of electrical energy has grown rapidly for both static applications and the portable electronics enforcing the substantial improvement in battery systems, and Li-ion batteries have been proven to have maximum energy storage density in all rechargeable batteries. However, major breakthroughs are required to consummate the requirement of higher energy density with lower cost to penetrate new markets. Graphite anode having limited capacity has become a bottle neck in the process of developing next generation batteries and can be replaced by higher capacity metals such as Silicon. In the present study we are …

Comparison Of Modal Analysis Results Of Laser Vibrometry And Nearfield Acoustical Holography Measurements Of An Aluminum Plate, Jennifer L. Potter

Dissertations, Master's Theses and Master's Reports - Open

Noise and vibration has long been sought to be reduced in major industries: automotive, aerospace and marine to name a few. Products must be tested and pass certain levels of federally regulated standards before entering the market. Vibration measurements are commonly acquired using accelerometers; however limitations of this method create a need for alternative solutions.

Two methods for non-contact vibration measurements are compared: Laser Vibrometry, which directly measures the surface velocity of the aluminum plate, and Nearfield Acoustic Holography (NAH), which measures sound pressure in the nearfield, and using Green’s Functions, reconstructs the surface velocity at the plate. The surface …

Dynamic Modeling, Simulation And Control Design Of A Parafoil-Payload System For Ship Launched Aerial Delivery System (Slads), Anand S. Puranik

Dissertations, Master's Theses and Master's Reports - Open

The objective of this research was to develop a high-fidelity dynamic model of a parafoilpayload system with respect to its application for the Ship Launched Aerial Delivery System (SLADS). SLADS is a concept in which cargo can be transfered from ship to shore using a parafoil-payload system. It is accomplished in two phases: An initial towing phase when the glider follows the towing vessel in a passive lift mode and an autonomous gliding phase when the system is guided to the desired point. While many previous researchers have analyzed the parafoil-payload system when it is released from another airborne vehicle, …

Dynamic Modeling Of Active Regeneration In Catalyzed And Non-Catalyzed Diesel Particulate Filters, Aamod Pethe

Dissertations, Master's Theses and Master's Reports - Open

Particulate matter (PM) emissions standards set by the US Environmental Protection Agency (EPA) have become increasingly stringent over the years. The EPA regulation for PM in heavy duty diesel engines has been reduced to 0.01 g/bhp-hr for the year 2010. Heavy duty diesel engines make use of an aftertreatment filtration device, the Diesel Particulate Filter (DPF). DPFs are highly efficient in filtering PM (known as soot) and are an integral part of 2010 heavy duty diesel aftertreatment system.

PM is accumulated in the DPF as the exhaust gas flows through it. This PM needs to be removed by oxidation periodically …

Topological Changes In 2d Simplicial Meshes For The Simulation Of Fractures, James R. Thunes

Dissertations, Master's Theses and Master's Reports - Open

A method for the introduction of strong discontinuities into a mesh will be developed. This method, applicable to a number of eXtended Finite Element Methods (XFEM) with intra-element strong discontinuities will be demonstrated with one specific method: the Generalized Cohesive Element (GCE) method. The algorithm utilizes a subgraph mesh representation which may insert the GCE either adaptively during the course of the analysis or a priori. Using this subgraphing algorithm, the insertion time is O(n) to the number of insertions. Numerical examples are presented demonstrating the advantages of the subgraph insertion method.

Effects Of Hibernation On Bone In Yellow-Bellied Marmots, Samantha J. Wojda

Dissertations, Master's Theses and Master's Reports - Open

Disuse osteoporosis is a problem for people with spinal cord injury or stroke, patients confined to bed rest, and astronauts exposed to microgravity. Unlike most mammals however, bears have been shown to prevent bone loss during hibernation, a seasonal period of disuse. Similarly, studies in ground squirrels indicate preservation of whole bone strength during hibernation, though evidence suggests there may be some increased osteocytic osteolysis. Uncovering the mechanism by which these animals prevent bone loss during hibernation could lead to an improved treatment for osteoporosis in humans. Marmots are a good animal model for these studies because they are small …

Development Of An Optimization Model For Biofuel Facility Size And Location And A Simulation Model For Design Of A Biofuel Supply Chain, Fengli Zhang

Dissertations, Master's Theses and Master's Reports - Open

To mitigate greenhouse gas (GHG) emissions and reduce U.S. dependence on imported oil, the United States (U.S.) is pursuing several options to create biofuels from renewable woody biomass (hereafter referred to as “biomass”). Because of the distributed nature of biomass feedstock, the cost and complexity of biomass recovery operations has significant challenges that hinder increased biomass utilization for energy production. To facilitate the exploration of a wide variety of conditions that promise profitable biomass utilization and tapping unused forest residues, it is proposed to develop biofuel supply chain models based on optimization and simulation approaches. The biofuel supply chain is …

Micro Combined Heat And Power Laboratory Development, Thomson Varghese

Dissertations, Master's Theses and Master's Reports - Open

Micro Combined Heat and Power (Micro-CHP) system produces both electricity and heat required for residential or small business applications. Use of Micro-CHP in a residential application not only creates energy and economic savings but also reduces the carbon foot print of the house or small business. Additionally, micro-CHP can subsidize its cost of operation by selling excess electricity produced back to the grid. Even though Micro-CHP remains attractive on paper, high initial cost and optimization issues in residential scale heat and electrical requirement has kept this technology from becoming a success. To understand and overcome all disadvantages posed my Micro-CHP …

Probe Studies Of A Hall Thruster At Low Voltages, Jerry L. Ross

Dissertations, Master's Theses and Master's Reports - Open

No abstract provided.

Post Processing Of Multiple Gps Receivers To Enhance Baseline Accuracy, Eddy H. Trinklein

Dissertations, Master's Theses and Master's Reports - Open

Inexpensive, commercial available off-the-shelf (COTS) Global Positioning Receivers (GPS) have typical accuracy of ±3 meters when augmented by the Wide Areas Augmentation System (WAAS). There exist applications that require position measurements between two moving targets. The focus of this work is to explore the viability of using clusters of COTS GPS receivers for relative position measurements to improve their accuracy. An experimental study was performed using two clusters, each with five GPS receivers, with a fixed distance of 4.5 m between the clusters. Although the relative position was fixed, the entire system of ten GPS receivers was on a mobile …

Development Of A Technique For Achieving An Optimum Bsfc For Laf Engine, Shreyash S. Ukidave

Dissertations, Master's Theses and Master's Reports - Open

The reserves of gasoline and diesel fuels are ever decreasing, which plays an important role in the technological development of automobiles. Numerous countries, especially the United States, wish to slowly decrease their fuel dependence on other countries by producing in house renewable fuels like biodiesels or ethanol. Therefore, the new automobile engines have to successfully run on a variety of fuels without significant changes to their designs. The current study focuses on assessing the potential of ethanol fuels to improve the performance of 'flex-fuel SI engines,' which literally means 'engines that are flexible in their fuel requirement.'

Another important area …

Implementation Of The Conjugate Heat Transfer Code In Kiva-4, Edward Ng

Dissertations, Master's Theses and Master's Reports - Open

KIVA is an open Computational Fluid Dynamics (CFD) source code that is capable to compute the transient two and three-dimensional chemically reactive fluid flows with spray. The latest version in the family of KIVA codes is the KIVA-4 which is capable of handling the unstructured mesh. This project focuses on the implementation of the Conjugate Heat Transfer code (CHT) in KIVA-4. The previous version of KIVA code with conjugate heat transfer code has been developed at Michigan Technological University by Egel Urip and is be used in this project. During the first phase of the project, the difference in the …

Local Degradation Of Structural, Mechanical, Electrical And Chemical Properties Of Membrane Electrode Assembly In Polymer Electrolyte Fuel Cell, Nishith Parikh

Dissertations, Master's Theses and Master's Reports - Open

Polymer electrolyte fuel cell (PEMFC) is promising source of clean power in many applications ranging from portable electronics to automotive and land-based power generation. However, widespread commercialization of PEMFC is primarily challenged by degradation. The mechanisms of fuel cell degradation are not well understood. Even though the numbers of installed units around the world continue to increase and dominate the pre-markets, the present lifetime requirements for fuel cells cannot be guarantee, creating the need for a more comprehensive knowledge of material’s ageing mechanism. The objective of this project is to conduct experiments on membrane electrode assembly (MEA) components of PEMFC …

Simulation Of Four Stroke Engine Cycle For A 4 - Valve Pentroof Engine In Kiva 3vr2, Yu Chen

Dissertations, Master's Theses and Master's Reports - Open

The main purpose of this project is to understand the process of engine simulation using the open source CFD code called KIVA. This report mainly discusses the simulation of the 4-valve Pentroof engine through KIVA 3VR2. KIVA is an open source FORTRAN code which is used to solve the fluid flow field in the engines with the transient 2D and 3D chemically reactive flow with spray. It also focuses on the complete procedure to simulate an engine cycle starting from pre- processing until the final results. This report will serve a handbook for the using the KIVA code.

Stochastic Knock Detection Model For Spark Ignited Engines, Yashodeep Lonari

Dissertations, Master's Theses and Master's Reports - Open

This report presents the development of a Stochastic Knock Detection (SKD) method for combustion knock detection in a spark-ignition engine using a model based design approach. Knock Signal Simulator (KSS) was developed as the plant model for the engine. The KSS as the plant model for the engine generates cycle-to-cycle accelerometer knock intensities following a stochastic approach with intensities that are generated using a Monte Carlo method from a lognormal distribution whose parameters have been predetermined from engine tests and dependent upon spark-timing, engine speed and load. The lognormal distribution has been shown to be a good approximation to the …

Synthesis Of Computations And Experiments For Obtaining Pulsatile Gas Flow Rates From Dynamic Pressure Difference Measurements Across An Orifice-Plate Meter, Nikhil Ajotikar

Dissertations, Master's Theses and Master's Reports - Open

The use of conventional orifice-plate meter is typically restricted to measurements of steady flows. This study proposes a new and effective computational-experimental approach for measuring the time-varying (but steady-in-the-mean) nature of turbulent pulsatile gas flows. Low Mach number (effectively constant density) steady-in-the-mean gas flows with large amplitude fluctuations (whose highest significant frequency is characterized by the value f_F) are termed pulsatile if the fluctuations have a direct correlation with the time-varying signature of the imposed dynamic pressure difference and, furthermore, they have fluctuation amplitudes that are significantly larger than those associated with turbulence or random acoustic wave signatures. …

Optimization Strategy For Resonant Mass Sensor Design In The Presence Of Squeeze Film Damping, Chengzhang Li, Michele H. Miller

Michigan Tech Publications, Part 1

This paper investigates the design optimization of an electrostatically actuated microcantilever resonator that operates in air. The nonlinear effects of electrostatic actuation and air damping make the structural dynamics modeling more complex. There is a need for an efficient way to simulate the system behavior so that the design can be more readily optimized. This paper describes an efficient analytical approach for determining the optimum design for a microcantilever resonant mass sensor. One simple case is described. The sensor design is a square plate that is coated with a functional polymer and attached to the substrate with folded leg springs. …

Me-Em Enewsbrief, December 2010, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.

Cutting Tool Insert Having Internal Microduct For Coolant, William J. Endres

Michigan Tech Patents

A cutting tool insert includes: a body defining a rake face, a flank face, and a cutting edge at an intersection of the rake and flank faces; and a cooling microduct within the body. A portion of the microduct extends along the cutting edge not more than 0.5 millimeter from the rake face, and not more than 0.5 millimeter from the flank face. The microduct has a cross-sectional area of not more than 1.0 square millimeter. The microduct is adapted to permit the flow of a coolant therethrough to transfer heat away from the cutting edge and extend the useful …

Me-Em Enewsbrief, September 2010, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.

Me-Em Enewsbrief, June 2010, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.

Me-Em Enewsbrief, March 2010, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.

Static And Dynamic Contact Angle Measurement On Rough Surfaces Using Sessile Drop Profile Analysis With Application To Water Management In Low Temperature Fuel Cells, Vinaykumar Konduru

Dissertations, Master's Theses and Master's Reports - Open

Fuel Cells are a promising alternative energy technology. One of the biggest problems that exists in fuel cell is that of water management. A better understanding of wettability characteristics in the fuel cells is needed to alleviate the problem of water management. Contact angle data on gas diffusion layers (GDL) of the fuel cells can be used to characterize the wettability of GDL in fuel cells. A contact angle measurement program has been developed to measure the contact angle of sessile drops from drop images. Digitization of drop images induces pixel errors in the contact angle measurement process. The resulting …

Vibro-Acoustical Analysis And Design Of A Multiple-Layer Constrained Viscoelastic Damping Structure, Fei Lin

Dissertations, Master's Theses and Master's Reports - Open

The goal of this research is to provide a framework for vibro-acoustical analysis and design of a multiple-layer constrained damping structure. The existing research on damping and viscoelastic damping mechanism is limited to the following four mainstream approaches: modeling techniques of damping treatments/materials; control through the electrical-mechanical effect using the piezoelectric layer; optimization by adjusting the parameters of the structure to meet the design requirements; and identification of the damping material’s properties through the response of the structure. This research proposes a systematic design methodology for the multiple-layer constrained damping beam giving consideration to vibro-acoustics.

A modeling technique to study …

Me-Em 2010 Annual Report, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering Annual Reports

Table of Contents

• First Year to First Career
• Faculty & Staff
• Alumni
• Resources
• Graduates
• Publications

Computational Study Of Internal And External Condensing Flows And Experimental Synthesis To Investigate Their Attainability And Stability In Ground-Based And Space-Based Environments, Shantanu Kulkarni

Dissertations, Master's Theses and Master's Reports - Open

This doctoral thesis presents the computational work and synthesis with experiments for internal (tube and channel geometries) as well as external (flow of a pure vapor over a horizontal plate) condensing flows. The computational work obtains accurate numerical simulations of the full two dimensional governing equations for steady and unsteady condensing flows in gravity/0g environments.

This doctoral work investigates flow features, flow regimes, attainability issues, stability issues, and responses to boundary fluctuations for condensing flows in different flow situations. This research finds new features of unsteady solutions of condensing flows; reveals interesting differences in gravity and shear driven situations; and …

Mathematical Analysis For Perceived Annoyance Of Impulsive Sounds In Terms Of Physical Factors, Gayatri S. Kadlaskar

Dissertations, Master's Theses and Master's Reports - Open

From the customer satisfaction point of view, sound quality of any product has become one of the important factors these days. The primary objective of this research is to determine factors which affect the acceptability of impulse noise. Though the analysis is based on a sample impulse sound file of a Commercial printer, the results can be applied to other similar impulsive noise.

It is assumed that impulsive noise can be tuned to meet the accepTable criteria. Thus it is necessary to find the most significant factors which can be controlled physically. This analysis is based on a single impulse. …

Three Dimensional Finite Element Simulation Of Polymer Melting And Flow In A Single-Screw Extruder : Optimization Of Screw Channel Geometry, Atakan Altinkaynak

Dissertations, Master's Theses and Master's Reports - Open

Single-screw extrusion is one of the widely used processing methods in plastics industry, which was the third largest manufacturing industry in the United States in 2007 [5]. In order to optimize the single-screw extrusion process, tremendous efforts have been devoted for development of accurate models in the last fifty years, especially for polymer melting in screw extruders. This has led to a good qualitative understanding of the melting process; however, quantitative predictions of melting from various models often have a large error in comparison to the experimental data. Thus, even nowadays, process parameters and the geometry of the extruder channel …

Advanced Mechanics Of Materials With Microstructure, Shreehari Elangovan

Dissertations, Master's Theses and Master's Reports - Open

The study of advanced materials aimed at improving human life has been performed since time immemorial. Such studies have created everlasting and greatly revered monuments and have helped revolutionize transportation by ushering the age of lighter–than–air flying machines. Hence a study of the mechanical behavior of advanced materials can pave way for their use for mankind’s benefit. In this school of thought, the aim of this dissertation is to broadly perform two investigations. First, an efficient modeling approach is established to predict the elastic response of cellular materials with distributions of cell geometries. Cellular materials find important applications in structural …