Mechanical Engineering Commons^™

Frontal Crash Analysis Of A Conformable Cng Tank Using Finite Element Analysis, Datta Sandesh Manjunath

Dissertations, Master's Theses and Master's Reports

The purpose of this study is to computationally model and analyze a Conformable Compressed Natural Gas (CNG) fuel tank for frontal crashes using Finite Element Analysis. Researchers have developed a CNG fuel tank, which is conformable, non-conventional and non-cylindrical. This tank increases cost efficiency, volumetric efficiency and cargo efficiency in CNG vehicle applications. A lightweight pickup truck (2015 Chevrolet Silverado) has been used to integrate the CNG tanks and field-testing has been conducted to demonstrate the application.

The report mainly focuses on the effective finite element modeling of the chassis, brackets and tanks using HYPERMESH and RADIOSS. The frontal crash …

Simulation Of Human Ankle Trajectory During Stance Phase Of Gait, Leslie Castelino

Dissertations, Master's Theses and Master's Reports

A simulation was developed which mimics the human gait characteristics based on the input of an individual’s gait trajectory. This simulation also estimates the impedance of the human ankle based on the ground reaction forces measured by the force plate. This simulation will accept alterations of the following parameters: total body weight, weight of the shank, weight of the foot, trajectories of the shank and foot of the individual and orientation of the force plate, which would generate a new gait trajectory for the ankle during the stance phase of gait. The goal of this simulation was to validate the …

Performance Of Hard Disk Drives In High Noise Environments, Trinoy Dutta

Dissertations, Master's Theses and Master's Reports

Digital information stored in rotational media, such as Hard Disk Drives (HDD) needs to be reliable and readily accessible. Various studies have been performed on the modal analysis of HDDs and the noise emitted during operation. Analysis performed by Siemens Corporation, IBM and Tyco Fire Protection Products show that HDDs are sensitive to noise. This report initially focusses on identifying the critical frequency ranges and the levels of noise where the performance of the drives reduces. A series of tests have been performed using pink noise at one-third octave frequency bands at sound pressure levels ranging from 80 dB to …

Gaskinetic Modeling On Dilute Gaseous Plume Impingement Flows, Chunpei Cai

Michigan Tech Publications, Part 1

This paper briefly reviews recent work on gaseous plume impingement flows. As the major part of this paper, also included are new comprehensive studies on high-speed, collisionless, gaseous, circular jet impinging on a three-dimensional, inclined, diffuse or specular flat plate. Gaskinetic theories are adopted to study the problems, and several crucial geometry-location and velocity-direction relations are used. The final complete results include impingement surface properties such as pressure, shear stress, and heat flux. From these surface properties, averaged coefficients of pressure, friction, heat flux, moment over the entire flat plate, and the distance from the moment center to the flat …

Energy Optimization And Fuel Economy Investigation Of A Series Hybrid Electric Vehicle Integrated With Diesel/Rcci Engines, Ali Solouk, Mahdi Shahbakhti

Michigan Tech Publications, Part 1

Among different types of low temperature combustion (LTC) regimes, eactively controlled compression ignition (RCCI) has received a lot of attention as a promising advanced combustion engine technology with high indicated thermal efficiency and low nitrogen oxides ( NOx" role="presentation" style="box-sizing: border-box; max-height: none; display: inline; line-height: normal; word-spacing: normal; overflow-wrap: normal; white-space: nowrap; float: none; direction: ltr; max-width: none; min-width: 0px; min-height: 0px; border: 0px; padding: 0px; margin: 0px; position: relative;">NOx ) and particulate matter (PM) emissions. In this study, an RCCI engine for the purpose of fuel economy investigation is incorporated in series hybrid electric vehicle (SHEV) architecture, …

Mitigation Of The Impact Of High Plug-In Electric Vehicle Penetration On Residential Distribution Grid Using Smart Charging Strategies, Chong Cao, Luting Wang, Bo Chen

Michigan Tech Publications, Part 1

Vehicle electrification presents a great opportunity to reduce transportation greenhouse gas emissions. The greater use of plug-in electric vehicles (PEVs), however, puts stress on local distribution networks. This paper presents an optimal PEV charging control method integrated with utility demand response (DR) signals to mitigate the impact of PEV charging to several aspects of a grid, including load surge, distribution accumulative voltage deviation, and transformer aging. To build a realistic PEV charging load model, the results of National Household Travel Survey (NHTS) have been analyzed and a stochastic PEV charging model has been defined based on survey results. The residential …

Mechanics Of Soft Polymers, Trisha Sain

TechTalks

Understanding the mechanics and physics of soft polymers are essential due to their widespread applications across disciplines. (e.g.-composite materials, bio mechanics, soft robotics etc.) The soft polymers in general inherent lightweight, high stretchability, extreme viscous damping and stimuli responsive behavior. Development of computational modeling strategy to predict their constitutive response, stimuli responsive behavior is indeed helpful for designing novel multifunctional soft composites, artificial mussels/tissues. In this talk I will briefly emphasize how we are developing multiscale-multiphysics based modeling methods for soft polymers to understand their macroscopic deformation mechanism, failure and other mechanical properties. The long term goal is to develop …

Aps Labs (Advanced Power Systems Research Center), Jeffrey D. Naber

TechTalks

Our mission is to promote & facilitate education and research in clean, efficient, and sustainable power and powertrain systems. The center was established in 2007 and in 2014 the 55,000 sq ft APSRC building located near the airport was denoted as a MTU core facility. Our new research contracts in FY2016 were over $2.5M. Our partners include automotive OEMs: GM, Ford, FCA, Toyota, Honda; Commercial OEMs: Cummins, Deere, Detroit, Isuzu, MHI; Suppliers: Delphi, Denso, Borg Warner, Hitachi; and DOE Labs: ANL, ORNL, PNNL, SNL, & INL. We have seven staff to assist in educational and R&D programs and facilities to …

Me-Em Enewsbrief, December 2016, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.

Two-Phase Transport In Proton Exchange Membrane Fuel Cells, Kazuya Tajiri

TechTalks

In Multiscale Transport Process Laboratory our research is focused on the experimental and computational analysis of transport phenomena in electrochemical devices and propulsion systems. In this talk our research activity on proton exchange membrane fuel cells (PEMFCs) for automotive application will be explained. Water management is one of the most critical issues in PEMFCs. The water generated in catalyst layer as a product of the electrochemical reaction needs to be removed through porous media by diffusion if it’s vapor, or by capillarity in case of liquid. In flow channels, the liquid water is removed primarily by inertial force of the …

Solid State Sound: A "Hot" Topic, Andrew Barnard

TechTalks

As seen with the latest iPhone 7 release, traditional audio components can now be a limiting factor in technology design. What if we could make a loudspeaker with no moving parts and virtually no weight? Carbon nanotube loudspeakers are such devices. They create sound using heat oscillations, as opposed to a moving diaphragm. They have the thickness of only a handful of carbon atoms, are flexible and stretchable. In this TechTalk I’ll discuss the carbon nanotube loudspeaker and the design challenges in maturing this intriguing technology.

Wearable Electronics, Human-Centered Monitoring, Ye Sarah Sun

TechTalks

Non-contact solution in wearable electronics: A conventional clinical system requires the use of wet electrodes that are in contact with skin using conductive gel to acquire physiological signals. Those systems can acquire high quality signals but may not be feasible for a long-term purpose due to the skin irritation and allergic contact dermatitis. The emerging of human-centered monitoring calls for alternative solutions. Recent technological advances enable capacitive measurement that can acquire signals through cloth or even with an air gap in wearable condition. In this TechTalk I will introduce the non-contact solution in wearable electronics.

Two-Temperature Dual-Phase-Lags Theory In A Thermoelastic Solid Half-Space Due To An Inclined Load, Ashraf M. Zenkour, Ahmed E. Abouelregal, Khaled A. Alnefaie, Nidal H. Abu-Hamdeh, Abdulmalik A. Aljinaidi, Elias C. Aifantis

Michigan Tech Publications, Part 1

This article addresses the thermoelastic interaction due to inclined load on a homogeneous isotropic half-space in context of two-temperature generalized theory of thermoelasticity with dual-phase-lags. It is assumed that the inclined load is a linear combination of both normal and tangential loads. The governing equations are solved by using the normal mode analysis. The variations of the displacement, stress, conductive temperature, and thermodynamic temperature distributions with the horizontal distance have been shown graphically. Results of some earlier workers have also been deduced from the present investigation as special cases. Some comparisons are graphically presented to estimate the effects of the …

Improving Automated Global Detection Of Volcanic So2 Plumes Using The Ozone Monitoring Instrument (Omi), Verity Flower, Thomas Oommen, Simon Carn

Michigan Tech Publications, Part 1

Volcanic eruptions pose an ever-present threat to human populations around the globe, but many active volcanoes remain poorly monitored. In regions where ground-based monitoring is present the effects of volcanic eruptions can be moderated through observational alerts to both local populations and service providers such as air traffic control. However, in regions where volcano monitoring is limited satellite-based remote sensing provides a global data source that can be utilized to provide near real time identification of volcanic activity. This paper details the development of an automated volcanic plume detection method utilizing daily, global observations of sulphur dioxide (SO2) by the …

Exergy Study On The Effect Of Material Parameters And Operating Conditions On The Anode Diffusion Polarization Of The Sofc, Khalid Zouhri, Seong Young Lee

Michigan Tech Publications, Part 1

In the presented work, a model is created in order to investigate the effect of different material parameters and operating conditions on the anode diffusion overpotential, which influence the exergy and energy efficiency of the solid oxide fuel cell (SOFC). In this research, it was demonstrated that the anode material parameters and operating conditions of the device components such as porosity, tortuosity, pore diameter, temperature, pressure and current density of the anode have various effects on the anode diffusion overpotential, which consequently affect the exergy and energy efficiency of the SOFC. The model has provided a strong direction on how …

Me-Em 2015-16 Annual Report, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering Annual Reports

Table of Contents

• Alumni: Leading with Simulation
• Education: Simulating the Future
• Faculty: Advancing Simulation
• Graduate Seminar Series
• Enrollment & Degrees
• Graduates
• Department News
• Faculty & Staff
• Alumni
• Donors
• Contracts & Grants
• Patents & Publications

Experimental Study Of The Flow Of Ferrofluid In A Porous Media Under A Magnetic Field, Muskaan Khurana

Dissertations, Master's Theses and Master's Reports

This research presents results from a laboratory-scale experimental setup that was designed to visualize the behavior of ferrofluid percolation through a porous media. Ferrofluids are colloidal suspensions made of magnetic particles of a few nanometers and stabilized in carrier liquids like water or mineral oil. Ferrofluids get magnetized and align themselves in the direction of a magnetic field when a field gradient is applied.

With the help of this experiment we investigate the viability of controlling fluid flow in porous medium by a magnetic field in vicinity. The experiments show that ferrofluids can be used as a transporting media to …

Shear Driven Suppressed Nucleation Annular Flow-Boiling In Millimeter-Scale Channels: Direct Numerical Simulations, Sharayu Bhasme

Dissertations, Master's Theses and Master's Reports

Many contemporary high heat-flux cooling applications are facilitated by mm-scale flow-boilers that operate in the steady annular suppressed nucleation regime (i.e., a thin evaporating liquid film flow covers the heated boiling-surface).

For such cases, this thesis presents a direct numerical simulation (DNS) approach. The steady algorithm and its accuracy are discussed. Representative detailed solutions for annular flow-boiling of FC-72 in a horizontal channel are presented.

Mechanical Testing Of Fused Filament 3-D Printed Components For Distributed Manufacturing, Nagendra Gautam Tanikella

Dissertations, Master's Theses and Master's Reports

Fused filament fabrication (FFF)-based open-source 3-D printers offer the potential of decentralized manufacturing both in developing and developed countries. Unfortunately, a severe lack of data and standards relating to material properties and printed components limit this potential. This thesis first investigates the mechanical properties of a wide-range of FFF materials and provides a database of mechanical strength of the materials tested. The results demonstrate that the tensile strength of a 3-D printed specimen depends largely on the mass of the specimen, which provides a means to estimate the strength of 3-D printed components. Then this information is used to evaluate …

Predictive Control Of Power Grid-Connected Energy Systems Based On Energy And Exergy Metrics, Meysam Razmara

Dissertations, Master's Theses and Master's Reports

Building and transportation sectors account for 41% and 27% of total energy consumption in the US, respectively. Designing smart controllers for Heating, Ventilation and Air-Conditioning (HVAC) systems and Internal Combustion Engines (ICEs) can play a key role in reducing energy consumption. Exergy or availability is based on the First and Second Laws of Thermodynamics and is a more precise metric to evaluate energy systems including HVAC and ICE systems. This dissertation centers on development of exergy models and design of model-based controllers based on exergy and energy metrics for grid-connected energy systems including HVAC and ICEs.

In this PhD dissertation, …

Experimental Investigation Of Fast Pyrolysis Of Arundo Donax In A Novel Paddle Reactor, Chintan Desai

Dissertations, Master's Theses and Master's Reports

The main objective of this research was to show the effectiveness of a novel paddle reactor for fast pyrolysis and study the effect of biomass particle size and reaction temperature of Arundo Donax a type of energy crop on the bio-oil yields. The novel paddle reactor showed effective mixing and heat transfer which were proved with the help of studying the residence time and the heating characteristics of the system respectively. The effect of different biomass particle sizes on the bio-oil yield was not significant, the bio-oil yield was approximately 50% for all the sizes. For Arundo Donax particle sizes …

Low Temperature Split Injection Spray Combustion: Ignition, Flame Stabilization And Soot Formation Characteristics In Diesel Engine Conditions, Ahmed Abdul Moiz

Dissertations, Master's Theses and Master's Reports

The aim of the PhD work is to investigate the fundamental differences in combustion behavior when split injections are used in low temperature combustion regime. In this thesis, the first injection is also called as pilot injection and second injection is also called as main injection. The broad aspects which are studied encompassing the investigation is to study the ignition delay, lift-off and soot formation of such a double split spray combustion. The mechanisms of ignition, lift-off and soot production are to be studied since the main ignition and lift-off were found to differ from the pilot which effect net …

A Nocsae Drop Test/ 3d-Fem Study On The Relationship Between Kinematic Response Of The Head, Head Impact Contact Pressure (Hicp) And Kinetic Response Of The Brain To Delineate The Risk Of Traumatic Brain Injuries (Tbi)., Raghavendra Krishna Tej Bhamidipati

Dissertations, Master's Theses and Master's Reports

How many times have you seen a person slip and fall down and had a good laugh about it? How many times we slip and fall down on the floor and got up and walked away thinking everything is normal? Probably we might wonder “Are drops which occur at a small height dangerous?” Yes, they can be. Brain injuries are main reason for the fatality in youth [1], and low level falls are one of the most neglected and understated injuries.

The main objective of this study is to study the response of the brain for low level falls from …

Incorporating Driver’S Behavior Into Predictive Powertrain Energy Management For A Power-Split Hybrid Electric Vehicle, Lei Feng

Dissertations, Master's Theses and Master's Reports

The goal of this series of research is to advance hybrid electric vehicle (HEV) energy management by incorporating driver’s driving behavior and driving cycle information. To reduce HEV fuel consumption, the objectives of this research are divided into the following three parts.

The first part of the research investigates the impact of driver’s behavior on the overall fuel efficiency of a hybrid electric vehicle and the energy efficiency of individual powertrain components under various driving cycles. Between the sticker number fuel economy and actual fuel economy, it is well known that a noticeable difference occur when a driver drives aggressively. …

Restraint System Design And Evaluation For Military Specific Applications, Sebastian Karwaczynski

Dissertations, Master's Theses and Master's Reports

This research focuses on designing an optimal restraint system for usage in a military vehicle applications. The designed restraint system must accommodate a wide range of DHM’s and ATD’s with and without PPE such as: helmet, boots, and body armor. The evaluation of the restraint systems were conducted in a simulated vehicle environment, which was utilized to downselect the ideal restraint system for this program.

In December of 2011 the OCP TECD program was formulated to increase occupant protection. To do this, 3D computer models were created to accommodate the entire Soldier population in the Army. These models included the …

Simulation Of Scalability For Autonomous Mobile Microgrids, Nathan Beyers

Dissertations, Master's Theses and Master's Reports

Microgrids are small-scale, decentralized systems for generation, storage, and management of electricity to provide power within a local area. By establishing these microgrids using autonomous robots, they can be made safer and more easily reconfigurable. This thesis presents a plan and outlines the infrastructure needed for scaling up previous experimental work on such systems. This work brings together a variety of tools in the form of both software and hardware to set the stage for how further development can be completed. An architecture for physical testing has been built to validate the full potential of navigation and making electrical connections …

Design Of Real-Time Combustion Feedback System And Experimental Study Of An Rcci Engine For Control, Jayant Kumar Arora

Dissertations, Master's Theses and Master's Reports

Premixed compression ignition (PCI) technologies offer high efficiency and low emissions but are usually confined by limited operation range as well as high pressure rise and heat release rate. In this work, a more recently developed PCI mode is explored where in-cylinder blending of two fuels with different auto-ignition characteristics (diesel and gasoline) is utilized to create reactivity stratification such that heat release rate and combustion timing can be controlled. This mode has been defined as Reactivity Controlled Compression Ignition (RCCI).

As part of this thesis, the main aim is to study various parameters that can be used to control …

Design Features And Optimization Of Profile Extrusion Dies, Abhishek Sai Erri Pradeep

Dissertations, Master's Theses and Master's Reports

This report deals with design of dies used in the plastic extrusion industry. The design methodology for extrusion dies has evolved over the years with advancement of computing technology. However, the design process is still heavily dependent on the experience of the die designer, and hence is still considered to be more of an art than science. Even for an experienced designer, the time required to design the die and perform consecutive fine tuning iterations is high. In this report, a proprietary optimization code for extrusion dies, .developed by Plastic Flow LLC, was tested and shown to be advantageous over …

Integration And Testing Of An Advanced Conformable Cng Tank In A Full-Sized Light-Duty Pickup, Abayomi Famuyiwa

Dissertations, Master's Theses and Master's Reports

Michigan Technological University is collaborating with Southwestern Energy and REL Inc. to develop and integrate a compressed natural gas (CNG) matrix tank that enables efficient packaging, increases range, and reduced cost for CNG vehicle applications. The vehicle being used in this project is a light-duty pickup truck to take advantage of the open space underneath the body and bed of the vehicle. With today’s cylindrical CNG tanks consuming cargo space, a solution is to develop a tank capable of being shaping to the underbody of the truck to free cargo space. University faculty and graduate students utilizes Finite Element Analysis …

An Experimental Investigation Of Low Temperature Combustion Regimes In A Light Duty Engine, Kaushik Kannan

Dissertations, Master's Theses and Master's Reports

A continuous investigation on the improvement of internal combustion engines is necessary due to the stringent emission and fuel economy regulations. Low Temperature Combustion (LTC) is a promising field of research since it can simultaneously reduce NOx and soot while attaining high thermal efficiencies in automotive engines. A thorough study of several LTC regimes is necessary to understand the quantitative comparison and the extent of feasibility of these regimes functioning on an automotive engine. This thesis concentrates on an experimental investigation of three different LTC modes namely Homogeneously Charged Compression Ignition (HCCI), Partially Premixed Compression Ignition (PPCI) and Reactivity Controlled …