Mechanical Engineering Commons^™

An Analytical Model To Predict The Length Of Oxygen-Assisted, Swirled, Coal And Biomass Flames, David Arthur Ashworth

Theses and Dissertations

Government regulations to reduce pollutants and increasing environmental awareness in the power generation industry have encouraged coal power plants to begin firing biomass in their boilers. Biomass generally consists of larger particles which produce longer flames than coal for a given burner. The length of the flame is important in fixed-volume boilers because of its influence on heat transfer, corrosion, deposition, and pollutant formation. Many pulverized fuel burners employ a series of co-annular tubes with various flows of fuel and air to produce a stabilized flame. A variable swirl burner with three co-annular tubes, each of variable diameter, has been …

Binder-Jet Printing Of Fine Stainless Steel Powder With Varied Final Density, Mohsen Ziaee, Eric M. Tridas, Nathan B. Crane

Faculty Publications

Binder jetting is an additive manufacturing process that produces relatively weak porous parts that are strengthened through sintering and/or infiltration. This paper reports on two different methods of preparing fine 316 stainless steel powder and their impact on the final sintered density and dimensions relative to direct printing into -22 micron powder. The first method uses agglomerates of fine powder. In the second, nylon 12 powders are mixed with the steel powder as a fugitive space holder to increase porosity. Sintered density and sintering shrinkage of agglomerate material are shown to vary with the density of the spread powder bed. …

The Development Of A Vertical-Axis Wind Turbine Wake Model For Use In Wind Farm Layout Optimization With Noise Level Constraints, Eric Blaine Tingey

Theses and Dissertations

This thesis focuses on providing the means to use vertical-axis wind turbines (VAWTs) in wind farms as an alternative form of harnessing wind energy in offshore and urban environments where both wake and acoustic effects of turbines are important considerations. In order for VAWTs to be used in wind farm layout analysis and optimization, a reduced-order wake model is needed to calculate velocities around a turbine quickly and accurately. However, a VAWT wake model has not been available to accomplish this task. Using vorticity data from computational fluid dynamic (CFD) simulations of VAWTs and cross-validated Gaussian distribution and polynomial surface …

Skin Strain Measurement To Predict Knee Joint Angles Through Nanocomposite Stain Gauges, Adin Martineau, James Tracy, Gavin Collins, Parker Rosquist, Dustin A. Bruening, Matt K. Seeley, David T. Fullwood, Anton E. Bowden

Biomedical Engineering Western Regional Conference

Explores the possibility of using high deflection nanocomposite strain gauges as knee joint angle sensor.

Redesign Of Computer Keyboards For Hospital And Consumer Use, Kent Williams, Brian Jensen, Anton Bowden

Biomedical Engineering Western Regional Conference

Application of carbon nanotube coatings to computer keyboards in order to reduce the spread of bacteria in hospitals and homes.

Keywords: carbon nanotube, bacteria, antimicrobial, keyboard, design, MRSA, biofilm

Soft-Tissue Artifact Compensation For Electromagnetic Motion Capture, George T. Dickinson, Steven K. Charles

Biomedical Engineering Western Regional Conference

This purpose of this study is to develop a soft-tissue artifact compensation algorithm for the upper arm using electromagnetic motion capture systems that can be implemented in a wide range of applications. This study focuses on compensation of humeral axial rotation and forearm axial rotation.

Characterization Of Essential Tremor In The Major Degrees Of Freedom Of The Upper Limb, Adam Pigg, David Standring, Steven Charles

Biomedical Engineering Western Regional Conference

No abstract provided.

Simulation Of Tremor Propagation In The Upper Limb, Thomas Corie, Steven K. Charles Dr

Biomedical Engineering Western Regional Conference

Essential tremor (ET) is the most common movement disorder and is estimated to affect between 1 and 12 million people in the US. Our long-term goal is to develop effective wearable tremor-suppressing devices. To reach this goal, we must first understand how tremor propagates from its mechanical origin (muscle) to the hand, where it matters most. The purpose of the current work is to characterize the extent to which tremor in different muscles or muscle groups contributes to tremor at the hand.

Computational Characterization Of Blood Vessel Strain In Wire Myography, Sameer S. Nandikar, M Converse, K L. Monson

Biomedical Engineering Western Regional Conference

Blood vessels, and the mechanical forces that act on them, play a key role in both health and disease. As a consequence, the mechanical properties of vessels have been under study for over a century. A variety of approaches have been used to define vessel properties, including stretching of vessel rings to study circumferential behavior, a configuration commonly used in wire myography. The objective of the present study was to develop a finite element model to quantify strains throughout a vessel ring during such loading.

A Nanocomposite Sensor Neck Sleeve For Tracking In Vivo Spine Kinematics In The Alpaca, Colton Porter Graham, Anton Bowden

Biomedical Engineering Western Regional Conference

Chronic low back pain in the US is often attributed to intervertebral disc degeneration. Camelids, particularly alpacas, pose a potential model for spinal treatment due to similarity of the spinal structure and vertical loading. Alpacas also exhibit a high rate of natural disc degeneration. To gain more understanding about how disc degeneration is caused in alpacas it is necessary to understand the loading and motion of the alpaca cervical spine. The goal of the present work was to incorporate nanocomposite sensors into a custom-designed neck sleeve to track the daily in-vivo neck motion of an alpaca in its natural environment.

Using Optimization To Determine Tremor Propagation, Paul Curtis, Steven K. Charles

Biomedical Engineering Western Regional Conference

: Essential Tremor (ET) is one of the most common movement disorders, with millions affected in the US. Currently there are two main treatment options: medication and deep brain stimulation (DBS). Available medications are only 50% effective, and in only 50% of patients, and many patients consider DBS too invasive. The purpose of our research is to determine the origin and propagation of tremor throughout the upper limb.

Portable, Powerless Automation Of Valve Actuation For Microfluidic Large-Scale Integration Technology, Andrew Schmidt Mr., Matt Fitzgerald Mr., Emre Araci Mr., Connor Mcloughlin Mr.

Biomedical Engineering Western Regional Conference

Portable, powerless automation of valve actuation for microfluidic large-scale integration technology

Analysis Of Rigid Extended Object Co-Manipulation By Human Dyads: Lateral Movement Characterization, Erich Mielke, Eric Townsend, Marc D. Killpack

Faculty Publications

During co-manipulation involving humans and robots, it is necessary to base robot controllers on human behaviors to achieve comfortable and coordinated movement between the human-robot dyad. In this paper, we describe an experiment between human-human dyads and we record the force and motion data as the leader-follower dyads moved in translation and rotation. The force/motion data was then analyzed for patterns found during lateral translation only. For extended objects, lateral translation and in-place rotation are ambiguous, but this paper determines a way to characterize lateral translation triggers for future use in human-robot interaction. The study has 4 main results. First, …

A Well Clear Recommendation For Small Uas In High-Density, Ads-B-Enabled Airspace, Timothy Mclain, Matthew O. Duffield

Faculty Publications

With the growing popularity of small unmanned aircraft systems (UAS), there is a significant need to enable small UAS to detect and avoid collisions with both manned and unmanned aircraft. The capabilities of ADS-B make it an attractive sensor for detect and avoid (DAA), but it is susceptible to frequency congestion. This paper quantitatively analyzes the frequency limitations of 978 MHz ADS-B. It then uses these limitations to make a recommendation for well clear in ADS-B-equipped airspace that has a high density of small UAS operations.

Hybrid Concentrated Solar Thermal Power Systems: A Review, Kody M. Powell, Khalid Rashid, Kevin Ellingwood, Jake Tuttle, Brian D. Iverson

Faculty Publications

Concentrated solar power (CSP), or solar thermal power, is an ideal technology to hybridize with other energy technologies for power generation. CSP shares technology with conventional power generation and can be readily integrated with other energy types into a synergistic system, which has many potential benefits including increased dispatchability and reliability, improved efficiency, reduced capital costs through equipment sharing, and the opportunity for flexible operation by alternating between energy sources. Another advantage of CSP technology is the ability to readily store via thermal energy storage (TES), making the intermittent solar resource dispatchable. A review of CSP hybridization strategies with coal, …

Controlled Manipulation Of Floating Objects On Deformed Fluid Interfaces And Conditions For Stable Equilibria, Jose M. Carballo, Qi Ni, Jose Vasquez, Nathan B. Crane

Faculty Publications

At the millimeter scale, interactions between floating and semi-immersed objects are significant. The local curvature of the interface is modified by the weight/buoyancy forces of floating objects, and by the surface properties of semi-immersed objects. The curvature changes generate attractive (or repulsive) interactions between floating parts, and semi-immersed objects. This work demonstrates how electrowetting can manipulate these interactions in order to position, align, assemble and transport parts attached to the fluid interface. This demonstrates one way in which fluid interfaces can provide an alternative to standard pick and place technology for part positioning/assembly. Typically, the part/rod forces are purely attractive …

Improving Sensitivity Of Electrochemical Sensors With Convective Transport In Free-Standing, Carbon Nanotube Structures, Benjamin J. Brownlee, Kevin M. Marr, Jonathan C. Claussen, Brian D. Iverson

Faculty Publications

High-aspect-ratio, porous membrane of vertically-aligned carbon nanotubes (CNTs) were developed through a templated microfabrication approach for electrochemical sensing. Nanostructured platinum (Pt) catalyst was deposited onto the CNTs with a facile, electroless deposition method, resulting in a Pt-nanowire-coated, CNT sensor (PN-CNT). Convection mass transfer enhancement was shown to improve PN-CNT sensor performance in the non-enzymatic, amperometric sensing of hydrogen peroxide (H₂O₂). In particular, convective enhancement was achieved through the use of high surface area to fluid volume structures and concentration boundary layer confinement in a channel. Stir speed and sensor orientation especially influenced the measured current in …

Fundamental Principles Of Tremor Propagation In The Upper Limb, Andrew D. Davidson, Steven Knight Charles

Faculty Publications

Although tremor is the most common movement disorder, there exist few effective tremor-suppressing devices, in part because the characteristics of tremor throughout the upper limb are unknown. To clarify, optimally suppressing tremor requires a knowledge of the mechanical origin, propagation, and distribution of tremor throughout the upper limb. Here we present the first systematic investigation of how tremor propagates between the shoulder, elbow, forearm, and wrist. We simulated tremor propagation using a linear, time-invariant, lumped-parameter model relating joint torques and the resulting joint displacements. The model focused on the seven main degrees of freedom from the shoulder to the wrist …

Extending The Upper Temperature Range Of Microchip Gas Chromatography Using A Heater/Clamp Assembly, Abhijit Ghosh, Jacob E. Johnson, Johnathan G. Nuss, Brittany A. Stark, Aaron R. Hawkins, Luke T. Tolley, Brian D. Iverson, H. Dennis Tolley, Milton L. Lee

Faculty Publications

Miniaturization of gas chromatography (GC) instrumentation is of interest because it addresses current and future issues relating to compactness, portability and field application. While incremental advancements continue to be reported in microchip GC, the current performance is far from acceptable. This lower performance compared to conventional GC is due to factors such as pooling of the stationary phase in corners of non-cylindrical channels, adsorption of sensitive compounds on incompletely deactivated surfaces, shorter column lengths and less than optimum interfacing to injector and detector. In this work, a microchip GC system was developed that solves the latter challenge, i.e. microchip interfacing …

Gradient-Based Optimization Of Wind Farms With Different Turbine Heights, Andrew P.J. Stanley, Jared Thomas, Andrew Ning, Jennifer Annoni, Katherine Dykes, Paul Fleming

Faculty Publications

Turbine wakes reduce power production in a wind farm. Current wind farms are gen- erally built with turbines that are all the same height, but if wind farms included turbines with different tower heights, the cost of energy (COE) may be reduced. We used gradient-based optimization to demonstrate a method to optimize wind farms with varied hub heights. Our study includes a modified version of the FLORIS wake model that accommodates three-dimensional wakes integrated with a tower structural model. Our purpose was to design a process to minimize the COE of a wind farm through layout optimization and varying turbine …

Eliminating The Illusion Of Learning From Engineering Courses, Jason Weaver

Faculty Publications

This paper describes the efforts of the author to incorporate tools into an undergraduate engineering course to help facilitate better learning and assess proficiency more effectively by avoiding the illusion of learning. Several techniques are used, including suggestions from the recent book Make It Stick by Brown, Roediger, and McDaniel. Student feedback and instructor observations are discussed, and future recommendations for the course are given

Design And Frequency Characterization Of Dual-Piezoresponsive Foam Sensors, Cory Nelson Newton

Theses and Dissertations

Multifunctional "self-sensing" materials at the frontiers of current research are generally designed to gather only a single type of information (such as quasi-static strain data). This project introduces a new sensor that is both multifunctional and dual-response, indicating its ability to not only perform in mechanical and sensing functions but also in its ability to sense multiple types of response. The proposed new class of sensing materials, comprised of nanocomposite polymer foams, exhibits measurable piezoresistive and quasi-piezoelectric phenomena in the form of change in resistance and voltage generation in response to deformation, respectively. An initial sampling of the envelope of …

Feasibility Of Friction Stir Processing (Fsp) As A Method Of Healing Cracks In Irradiated 304l Stainless Steels, Cameron Cornelius Gunter

Theses and Dissertations

The current US fleet of nuclear reactors has been in service for three decades. Over this period, existing welds in stainless steel (SS) shrouds have sustained stress corrosion cracking (SCC) and are in need of repair. Additionally, helium has formed interstitially as a byproduct of proton bombardment. Current repair technology, such as TIG welding, puts extreme amounts of heat into the material and allows for interstitial helium atoms to aggregate and form bubbles/voids at grain boundaries. This significantly weakens the material, proving to be a very counterproductive and ineffective repair technique. Much study has been done on friction stir processing …

Autonomous Goal-Based Mapping And Navigation Using A Ground Robot, Jeffrey L. Ferrin

Theses and Dissertations

Ground robotic vehicles are used in many different applications. Many of these uses include tele-operation of the robot. This allows the robot to be deployed in locations that are too difficult or are unsafe for human access. The ability of a ground robot to autonomously navigate to a desired location without a-priori map information and without using GPS would allow robotic vehicles to be used in many of these situations and would free the operator to focus on other more important tasks. The purpose of this research is to develop algorithms that enable a ground robot to autonomously navigate to …

Evolvability And Excess Capability As A Response To Uncertain And Future Requirements, Jeffrey Douglas Allen

Theses and Dissertations

Product and system designers face many challenges in the modern world. Designing products that will be subject to emerging or uncertain requirements can be one of the most significant of these challenges. A major risk associated with emerging or uncertain requirements is premature obsolescence. Large-scale, complex engineered systems, such as, aircraft, spacecraft, large seagoing vessels, communication and power systems are especially susceptible to this issue. However, this challenge is not limited to only large-scale complex systems. Even relatively simple products can suffer from premature obsolescence and even failure to be initially accepted, due to inadequately understood or changing requirements. One …

Extending Time Until Failure During Leaking In Inflatable, Pneumatically Actuated Soft Robots, Joshua Parker Wilson

Theses and Dissertations

Soft robots and particularly inflatable robots are of interest because they are lightweight, compact, robust to impact, and can interact with humans and their environment relatively safely compared to rigid and heavy traditional robots. Improved safety is due to their low mass that results in low-energy collisions and their compliant, soft construction. Inflatable robots (which are a type of soft robot) are also robust to impact and have a high torque to weight ratio. As a result inflatable robots may be used for many applications such as space exploration, search and rescue, and human-robot interaction. One of the potential problems …

Integrated Design Of Downwind Land-Based Wind Turbines Using Analytic Gradients, Andrew Ning, Derek Petch

Faculty Publications

Wind turbines are complex systems where component-level changes can have significant system-level effects. Effective wind turbine optimization generally requires an integrated analysis approach with a large number of design variables. Optimizing across large variable sets is orders of magnitude more efficient with gradient-based methods as compared to gradient-free method, particularly when using exact gradients. We have developed a wind turbine analysis set of over 100 components where 90% of the models provide numerically exact gradients through symbolic differentiation, automatic differentiation, and adjoint methods. This framework is applied to a specific design study focused on downwind land-based wind turbines.

Downwind machines …

The Feasibility Of Using A Markerless Motion Capture Sensor (Leap MotionTm Controller) Forquantitative Motor Assessment Intended For A Clinical Setting, Clay Jordan Kincaid

Theses and Dissertations

Although upper limb motor impairments are common, the primary tools for assessing and tracking these impairments in a clinical setting are subjective, qualitative rating scales that lack resolution and repeatability. Markerless motion capture technology has the potential to greatly improve clinical assessment by providing quick, low-cost, and accurate tools to objectively quantify motor deficits. Here we lay some of the groundwork necessary to enable markerless motion capture systems to be used in clinical settings. First, we adapted five motor tests common in clinical assessments so they can be administered via markerless motion capture. We implemented these modified tests using a …

Material Selection Shape Factors For Compliant Arrays In Bending, David T. Fullwood, Todd G. Nelson, Jared T. Bruton, Nathan E. Rieske, M. Patrick Walton, Larry L. Howell

Faculty Publications

Similar to the general class of metamaterials, compliant arrays (CAs) are engineered from an array of subelements that combine to produce a response that is typically not available from a at panel made of a single material. As such, analysis and design of CA systems requires the integration of both the material and geometrical properties of the array. This paper proposes a convenient and efficient method of combining these essential elements using analytically derived shape factors for bending modes. The approach is validated experimentally, and used to demonstrate large regions of previously inaccessible property combinations in material selection charts that …

Vibration Monitoring Via Nano-Composite Piezoelectric Foam Bushings, David T. Fullwood, Evan T. Bird, A Jake Merrell, Brady K. Anderson, Cory N. Newton, Parker G. Rosquist, Anton E. Bowden, Matthew K. Seeley

Faculty Publications

Most mechanical systems produce vibrations as an inherent side effect of operation. Though some vibrations are acceptable in operation, others can cause damage or signal a machine’s imminent failure. These vibrations would optimally be monitored in real-time, without human supervision to prevent failure and excessive wear in machinery. This paper explores a new alternative to currently-used machine-monitoring equipment, namely a piezoelectric foam sensor system. These sensors are made of a silicone-based foam embedded with nano- and micro-scale conductive particles. Upon impact, they emit an electric response that is directly correlated with impact energy, with no electrical power input. In the …