Mechanical Engineering Commons^™

Hydrogen Embrittlement In Shot-Peened Steel, Jia-Huei Tien, David R. Johnson, David Bahr

15th International Conference on Shot Peening

This work investigates the role of shot peening on hydrogen embrittlement resistance in quenched and tempered 1070 steel. Thermal desorption spectroscopy results revealed that shot-peened specimens contained nearly twice the hydrogen (H) content of unpeened samples when charged under the same electrochemical conditions, suggesting the introduction of additional trapping sites occur during peening. The mechanism underlying this behavior can be associated with increased dislocation density and is more consistent with the HELP mechanism. Residual stress measurements show a significant relaxation of compressive stresses in shot-peened specimen after H charging, indicating H enhanced dislocation rearrangement. Both unpeened and peened specimens exhibited …

Investigations On The Fatigue Strength Of Threads Produced By Different Fabrication Techniques, Philippe Du Maire, Jürgen Hoffmeister, Andreas Öchsner, Michael Johlitz

15th International Conference on Shot Peening

The increasing importance of sustainability in engineering demands the development of long-lasting, high-performance components that reduce material and energy consumption over time. This study investigates how different thread manufacturing processes, i.e., cutting, rolling, and deep rolling, affect the fatigue strength of bolts made from 42CrMo4+QT steel. Cylindrical specimens with M12 threads were subjected to cyclic tensile loading with constant mean stress. Fatigue strength was evaluated using the staircase method, and supporting analyses included X-ray diffraction for residual stress, and full width half maximum examination and Vickers microhardness measurements. Results show that thread rolling significantly improves fatigue strength, achieving 113.8 MPa …

Effect Of Fine Particle Peening Induced Material Transfer On The Initial Deposition Behavior Of Nickel Electroplating On Aluminum Substrate, Kazuki Iijima, Yutaka Kameyama, Hideaki Sato, Shuhei Kodama

15th International Conference on Shot Peening

Plating on aluminum requires a complex zincate pretreatment. Fine Particle Peening (FPP), using particles ≤200 µm, has gained attention as an alternative due to its ability to transfer particle components onto the surface, potentially improving deposition and adhesion. Previous studies showed enhanced plating on aluminum treated with steel particles. This study investigates the effectiveness of FPP as a pretreatment for nickel electroplating by examining initial deposition behavior. A1050-H24 aluminum was treated using FPP with either steel or glass particles, compared to an untreated specimen. Steel particle FPP created a lamellar microstructure with alternating iron and aluminum phases. EBSD revealed that …

Effects Of Laser Peening On Fatigue Properties Of Welded Aluminum Thin Plates, Kiyotaka Masaki, Yoshio Mizuta, Satoshi Tamaki, Yuji Sano

15th International Conference on Shot Peening

To improve the fatigue properties of welded aluminum alloy thin plates used in transportation machinery, handheld laser peening (HH-LP) was applied to 2 mm-thick A5083-O specimens prepared by bead-on TIG welding. Conventional laser peening often causes warping in thin plates, but the HH-LP treatment using low-energy laser pulses avoids this problem. The HH-LP treatment introduced compressive residual stresses of over 200 MPa on the heat-affected zone (HAZ) of the welded specimens. Fatigue tests under plane bending conditions revealed that the HH-LP treatment significantly improved the fatigue strength of the welded specimens, achieving a level comparable to that of the base …

Microstructural Changes And Residual Stress Generation On The Periodically Patterned Surface Texture Fabricated By Angled Fine Particle Peening, Yutaka Kameyama, Hideaki Sato, Ryokichi Shimpo

15th International Conference on Shot Peening

Focusing on the potential of peening technology as a surface texturing technique, angled fine particle peening (angled-FPP) has been proposed to fabricate a specific periodical surface structure, which possibly provides various surface functions. It is necessary to further characterize the textured surface to earn more advantages from angled-FPP. Thus, in this paper, texture formation phenomena, residual stress, and microstructural changes were investigated on the angled-FPP specimens.

Improving Fatigue Strength And Life Of Single Crystal Cmsx-4, Jochen Peter Fuhr, Lloyd Hackel, Nicolau I. Morar, Noah Holtham, Keivan Davami, Montu Sharma, Rajkumar Roy

15th International Conference on Shot Peening

The deep penetration of laser peening (LP) and retention of residual stress at high temperature by LP is significant in improving fatigue life and strength of superalloys exposed to high temperature and corrosion. Single crystal CMSX-4, was evaluated for stress relaxation and both fatigue life and fatigue strength of material that was LP-treated compared to non-LP and shot-peened (SP) specimens. LP was done with multiple layers using a 20 J/pulse laser where the laser high energy enabled using a 5 mm spot size on the metal surface. Stress measurements by the slitting technique showed the plastic penetration depth exceeded SP …

Recent Progress And Scientific Challenges In Wire-Arc Additive Manufacturing Of Metallic Multi-Material Structures, Sainand M. Jadhav, Sambhaji Kusekar, Akash Belure, Satyavan Digole, Abhijeet Mali, Muralimohan Cheepu, Manoj Mugale, Suhas Alkunte, Duckbong Kim

Faculty Articles

Metallic multi-material structures are heterogeneous structures characterized by changing composition, microstructures, and site-specific characteristics, advantageous for numerous applications where multifunctionality is desired. Metallic multi-material structures are known as bimetallic structures (BSs), which are functionally graded materials (FGMs). In recent years, wire-arc additive manufacturing (WAAM) advanced as a promising additive manufacturing process to realize the fabrication of these structures due to its high deposition rate, cost-effectiveness, and material utilization efficiency. This review presents a comprehensive overview of the recent progress, processing strategies, and scientific challenges in WAAM of multi-material structures. The paper begins with an introduction to multi-material structures, followed by …

Shape Memory Behavior In Medium To High Entropy Shape Memory Alloys: Design, Prediction, And Experimental Analysis, Hatim Raji

Theses and Dissertations

This dissertation provides a data-driven system integrating synthetic data generation and machine learning (ML) techniques to create multicomponent SMA compositions with specific transformation temperatures (TTs). Models were trained to represent the nonlinear dependencies influencing martensitic transformation behavior by using elemental, thermodynamic, and process-related aspects. The capacity of the ML models on medium entropy NiTiHfPd and high entropy NiTiHfZrCu systems accuracy was confirmed by experimental validation showing TTs closely matched with model outputs.

Material Extrusion 3d Printing Of Metal Alloy: Material, Methods And Application., Sihan Zhang

Electronic Theses and Dissertations

Material extrusion (MEX) additive manufacturing presents a promising pathway for producing metal components with complex geometries while avoiding the safety hazards associated with loose powder handling in conventional metal additive manufacturing processes. This dissertation investigates the development and optimization of MEX processes for aluminum alloys, addressing critical challenges in feedstock formulation, printing parameter optimization, and post-processing strategies. Three distinct approaches were explored to advance the capabilities of aluminum MEX: filament-based processing of 6061 aluminum, paste-based extrusion of 6061 aluminum, and development of a novel aluminum-magnesium-tin alloy system for space manufacturing applications. The filament-based approach successfully demonstrated the production of 6061 …

Effect Of Manufacturing And Machining Process On Recycled Composite Connecting Rods Under Tension And Compression, Walter W. Oppelt

Master's Theses

Carbon fiber reinforced polymer (CFRP) is an engineering material renowned for its high-strength and low-density material properties. Such properties make CFRPs especially useful for applications across many industries, including aerospace, automotive, marine, sporting goods, oil and gas, and more. However, with such favorable material properties comes the cost of high energy usage required to produce raw carbon fiber. Recycled carbon fiber (rCF) has emerged as a promising alternative, offering a significant reduction in energy usage. This research explores the viability of applying recycled CFRPs to internal combustion engines to both reduce energy costs during manufacturing and while in use. Mechanical …

Comparative Study Of Experimental And Fea Strain Data For Cnt-Coated Fiberglass Sensors, Extensometers, And Metal Foil Strain Gauges, Omar Dwidar

Master's Theses

Material testing is essential across industries such as aerospace, automotive, and construction, playing a critical role in verifying material selection, diagnosing failures, and understanding the development of flaws in structures. These insights are key to designing successful, reliable systems. Conventional metal foil strain gauges are low cost and reliable but provide limited sensitivity with a typical gauge factor around 2. Extensometers provide highly sensitive strain measurements with the disadvantage of a bulky form factor. With advanced materials such as carbon nanotubes, it is possible to manufacture a sensor with the sensitivity closer to that of an extensometer with the small …

Model-Based Design Of Compressed Lithium-Metal Pouch Cell Battery Modules For Evtol Applications, Scott J. Stirling

Master's Theses

Batteries with higher specific energy and power are essential for extending the range and performance of electric vertical takeoff and landing aircraft (eVTOLs). Anode-free lithium-metal pouch cells offer strong potential at the cell-level but require high compressive pressures to enhance cycle life and discharge performance. These pressures necessitate heavier structural components, reducing packaging efficiency at the module level.

To evaluate this tradeoff, a full-factorial enumeration model was developed to explore viable module designs within a constrained packaging volume. The model scales subsystem masses, enforces design rules and material limits, and accounts for large (~20%) cell thickness changes during cycling.

Results …

Fire Fossils: Biomineral Infrastructures In Untangling Climates, Tanmayee More

Masters Theses

Diatoms drift, sediments sink, wildfires generate their own weather. Lightning strikes can blast sand into glass, and microscopic organisms do the same in the cold recesses of the ocean. What alchemies and metabolisms catalyze space, time, and energy? What are the thermodynamics of infrastructure in Climate Change?

Places, materials, and beings are afterimages. Through alchemical experiments, and multi-scalar imaging, I develop simulations of wildfires, and their profound, reverberating effects. In this thesis, a glass-meets-landscape experimental process enters these obscured conditions and renders new material relations for the built environment.

Adjustable Dynamometer Motor Mount, Garrett Carson Ng, Elijah Siegel Reuven, Ethan Fong, Daniel Larimer

Mechanical Engineering

The Cal Poly Electrical Engineering Department and sponsor Dr. Dolan needs a manufacturable motor fixture that securely aligns motors of various sizes with dynamometers. Previous lab motor fixtures could not accommodate motors of different sizes, making precise alignment between motors and dynamometers time-consuming and unreliable. Our team developed a modular, manufacturable fixture capable of aligning various motor sizes quickly, accurately, and securely, enhancing lab consistency and usability.

Exploring Metal Additive Manufacturing In Martian Atmospheric Environments, Zane Mebruer

Mechanical Engineering Undergraduate Honors Theses

On-surface manufacturing is key to the success of a planetary colonization, especially that of Mars. However, traditional subtractive manufacturing processes are equipment, energy, and material intensive, meaning novel additive manufacturing (AM) processes must be pursued for this end. Selective laser melting, one of the most effective and versatile AM methods, would be incredibly beneficial to a Martian mission but requires an artificial argon atmosphere to create effective parts. The purpose of this study was to examine if carbon dioxide, the gas that makes up over 95% of Mars’ surface atmosphere, would be a sufficient substitute for argon in SLM fabrication. …

Advanced Manufacturing Of Multifunctional Shape Memory Polymer Composites And Self-Healing Systems, John B. Konlan

LSU Doctoral Dissertations

The need for multifunctional light weight structures for engineering applications is on the rise. Multifunctional composites are desired because of their ability to combine multiple functionalities into one structure. The advantages of a high strength-to-weight ratio of multifunctional composites make them desirable and suitable for use in energy-efficient applications. Shape-memory polymers (SMPs) have attracted interest over the past several decades because of their multifunctional nature. They have found use in many applications such as aerospace, satellites, automobiles, textiles, and biomedical devices, where lightweight and multifunctionality are key. The self-healing nature of most SMPs makes them suitable for use in lightweight …

Intelligent Turning Cyber-Physical Systems Modeling Using Sysml, Prithbey Raj Dey, David Lee Enke, Mario F. Buchely

Engineering Management and Systems Engineering Faculty Research & Creative Works

Cyber-Physical Systems (CPS) support industrial automation that incorporates people, hardware, signal, computation, and control using networking to achieve desired results. The complex automated CPS design demands a standard and comprehensive approach to appropriately identify the system requirements, define the architecture, and model the relationships among the software and hardware components. Systems Modeling Language (SysML) provides the capability for a comprehensive modeling to capture the desired design requirements in the systems architecture. SysML enables performance estimation of the model by analyzing constraints while identifying interactions among the components through various behavioral diagrams. In this paper, SysML is applied to the design …

Controlling Nitrogen Pickup During Induction Melting Of Ultrahigh-Strength Cr-Ni-Mo-V Steels, Kingsley T. Amatanweze, Viraj A. Athavale, Mario F. Buchely, Laura N. Bartlett, Ronald J. O'Malley, Daniel M. Field

Materials Science and Engineering Faculty Research & Creative Works

Nitrogen pickup during air induction melting can result in porosity and a loss of fracture toughness in ultrahigh-strength quenched and tempered steel castings. Nitrogen atoms are easily adsorbed into liquid steel upon exposure to the air, and argon shrouding alone has limited effectiveness. Previous studies have shown that proper charge sequencing and maintaining a high amount of dissolved oxygen in the melt prior to tapping and deoxidation can limit nitrogen pickup in the melt. In the current study, the effect of melt practice and charging procedure on nitrogen pickup was studied as a function of hold time in a series …

Effect Of Gating Design On Filling And Inclusion Control In An Al-Killed Cr-Mo-Ni Steel, Kingsley T. Amatanweze, Koushik Balasubramanian, Soumava Chakraborty, Viraj A. Athavale, Mario F. Buchely, Laura N. Bartlett, Ronald J. O'Malley, Daniel M. Field, Krista R. Limmer, Katherine M. Sebeck

Materials Science and Engineering Faculty Research & Creative Works

The effect of gating system design on the inclusion population and size distribution in an aluminum-killed low-alloy advanced high strength steel casting was studied. A mold with four different gating systems: pressurized and non-pressurized with side risers, naturally pressurized with a side riser, and naturally pressurized with a top riser, was designed using computational fluid dynamics and solidification software. The design allowed inclusion populations in castings produced with each gating system to be compared during the same pouring event. Samples taken from different positions just below the top surface of each casting were analyzed using an SEM/EDS system with automated …

Parametric Analysis Of Water Jet Descaling Efficiency Of Reheated Continuously Cast Thin Slab, Tochukwu P. Ojiako, Mario F. Buchely, Simon Lekakh, Ronald J. O'Malley, Richard Osei, Taha Tayebali

Materials Science and Engineering Faculty Research & Creative Works

Efficient oxide scale removal is critical for maintaining surface quality and process efficiency in steel manufacturing. This study optimizes water jet descaling by evaluating the performance of flat and rotary jet nozzles under varying process parameters. Using a combined approach of experimental analysis and computational fluid dynamics, it investigates the influence of pressure (138–275 bar), lead angle (0°, 15°, 25°), working distance (50–100 mm), and spray angle (15°–25°) on descaling efficiency. Findings indicate that flat jet nozzles achieve superior performance at short working distances due to concentrated impact forces, while rotary jet nozzles sustain efficiency over extended distances through dynamic …

Rheology Of Alumina Suspensions Subjected To Alternating Current Electric Fields For Freeze-Casting, Sivakumar Chithamallu, Ruksana Baby, Jacob L. Jones, Dipankar Ghosh

Mechanical & Aerospace Engineering Faculty Publications

Alternating current (AC) electric field can extrinsically tune freeze‐cast microstructure, originating from field‐induced increase in viscosity of ceramic suspensions. However, the changes that occur in a ceramic suspension and rheological behavior, ultimately affecting freeze‐cast microstructure, are not well understood. Moreover, the effects of AC electrokinetic forces and temperature on viscosity need to be decoupled. The viscosity and temperature of ceramic suspensions subjected to AC field and direct heating were measured, revealing that the increase in viscosity is due to AC dielectrophoretic forces rather than field‐induced heating of suspension. The shear thinning behavior of suspensions characterized using a power‐law model reveals …

Design And Development Of A Rapid Tensile Quench Rig, Tyler Jewell, Justin Naylor

Williams Honors College, Honors Research Projects

This report outlines the design process and implantation of a tensile quenching rig that incorporated forced convection and a frequency generator. When any metal is quenched, a vapor barrier forms around it. When this happens, it limits the heat flux that may occur until the barrier turns into just nucleate boiling. The vapor barrier acts as an insulator and causes the heat flux to fluctuate, causing uneven hardening which would limit the use of some materials. To combat this effect, we are trying to use forced convection, and something new, which is adding high frequency waves into the quenching process. …

Morphing Shape Metastructures Using The Hybrid Position Feedback Control And Bistable Structural Elements, Mehmet Simsek, Thomas E. Alberts, Onur Bilgen

Mechanical & Aerospace Engineering Faculty Publications

This research introduces a new multi-degree-of-freedom metastructure concept utilizing a hybrid position feedback controller. An arbitrary number of bistable segments, or structural elements, are connected serially or in parallel to form a distributed bistable structure, or a so-called metastructure. The hybrid controller, an unstable-then-stable second-order single-degree-of-freedom system, leverages the resonant mode of a bistable system to destabilize it and dynamically induce snap-through between equilibria. The metastructure inherits multiple bistable positions, maintaining equilibrium shapes without consuming power and enabling many equilibrium configurations. Two geometric configurations are proposed and analyzed using a modified hybrid feedback control approach, which rejects forces from neighboring …

Characterization Of The Solid-State Bonding For Simulated Charge And Seam Welds In The Porthole Die Extrusion Process, Randall L. Bowers

Theses and Dissertations--Chemical and Materials Engineering

The isothermal (ISO-T) compression configuration is ideal for utilizing as a material input of flow stress at temperature and strain rate in models of the porthole die extrusion process due to the isothermal nature of the test. Micro-tensile testing was conducted to validate the solid-state welding integrity of the ISO-T samples at various temperatures and strain rates. Results of the mechanical testing were correlated with fractography and microstructural evaluations of the welds to confirm bonding behavior. Both clean interface conditions and oxidation and lubrication layers were evaluated to simulate the difference of seam and charge welds in the process. Results …

Pulsed Arc Additive Manufacturing Of A Functionally Graded Er2209 Duplex Stainless Steel And Hsla-100 Structure: Morphology, Characterization, And Mechanical Performance, Stevens G. Hill Jr

College of Graduate Studies: Theses & Dissertations

Wire arc additive manufacturing is a process well suited to the efficient production of large structures. Duplex stainless steel exhibits high corrosion resistance and good strength which can be highly beneficial for industrial use. However, its use is limited due to its cost and complexity in controlling microstructure to achieve desired properties. In many cases, it can be highly beneficial to manufacture a component which uses specialty steel grades such as duplex stainless steel only where necessary, and utilizes more affordable, commonly available steels for reinforcement or bulk structural support. A functionally graded material satisfies these requirements by providing a …

Neural Operator And Physics-Informed Deep Learning Approaches For Inverse Design Of Composites And Manufacturing Processes, Minglei Lu

All Dissertations

In this dissertation, artificial intelligence (AI) models are designed and used to accelerate inverse design of composites and manufacturing processes. The critical bottlenecks in machine learning (ML) including data availability, data quality, model generalization and adaptation, interpretability, physical consistency, and the ’black box’ nature of models for the inverse design are addressed. And the proposed AI models are tested under different engineering scenarios. Firstly, a fast deep neural operator (DNO) structure was developed to significantly reduce training time. This model was tested in the context of additive manufacturing, a transformative industrial technology that allows for the creation of materials with …

Development Of Multifunctional Wood Composites With Integrated Phase Change Materials For Enhanced Thermal Management, Self-Healing, And Sustainability., Emmanuel Igbokwe

LSU Master's Theses

Abstract

This study focused on incorporating self-healing, flame retardancy, and energy harvesting capabilities into the wood composite to contribute to more sustainable and energy-efficient building practices. Oriented strand board has been widely used as sheath for roofing or dry walls in residential buildings. Residential buildings account for a large portion of energy consumption. Therefore, an oriented strand board with energy harvesting capability is highly desired. Additionally, flame retardancy and damage self-healing and end-of-life recycling are also critical features for buildings.

In this study, we prepared a novel oriented strand board by constructing sandwich structures. The face sheets of the sandwich …

An In-Situ Method For Quantifying Entropy Generation In Fatigue Via A Novel Thermographic Approach, Peyton J. Wilson

LSU Master's Theses

This work features a new approach that is used to measure the rate of plastic work during a cyclic fatigue test, based on the first and second laws of thermodynamics. Using the one-dimensional Fourier heat equation coupled with the concept of fracture fatigue entropy, the rate of plastic work during fatigue can be measured without the need to interrupt a fatigue test, and the accumulated entropy to failure can be quantified. Experimental fatigue tests are conducted on Aluminum 6061-T6 specimens under cyclic axial loading and Carbon Steel 1018 specimens under fully reversed cyclic bending loading. The obtained results in addition …

Utilization Of Sodium Flame Synthesis For The Formation And Deposition Of Pure Metal Materials For Applications In Additive Manufacturing, Zachariah Wargel

McKelvey School of Engineering Graduate Student Theses & Dissertations

Advanced material classes, such as high temperature alloys, ceramics, and refractory materials have become a key area of focus for expansion in the realm of additive manufacturing. Factors such as high melting points, material homogeneity, and physical properties such as ductility limit the application of popular additive manufacturing methods to these material classes. By utilizing sodium flame synthesis and deposition (SFD) technology, nanoparticle materials can be synthesized via combustion in a laminar co-flow diffusion burner and impacted such that the deposits can be used to manufacture designed components. By using the applicable precursor materials of metal chlorides and elemental sodium …

On The Structure, Energy, And Segregation Behavior Of Grain Boundaries In Metallic Systems, Yasir Mahmood

All Dissertations

Nearly all structural metallic systems are multi-component polycrystalline aggregates; their microstructures are composed of crystalline grains that are internally joined at grain boundaries (GBs). This thesis focuses on GB structure, energy, and chemistry, as these greatly influence many material properties and processes, including boundary dynamics during processing treatments or under operating conditions.

Using atomistic simulations, we examine the impact of metastable GB structures on solute segregation. A wide range of GB geometries and metastable structures are used in our study. The Al-Mg alloy is used because it is of interest for light weighting. The atomistic simulation results are used to …