Mechanical Engineering Commons^™

Tribological Performance Of Novel Nickel-Based Composite Coatings With Lubricant Particles, Ignacio Tudela, Andrew J. Cobley, Yi Zhang

Friction

The present study is focused on the evaluation of the tribological performance of novel Ni/hBN and Ni/WS2 composite coatings electrodeposited from an additive-free Watts bath with the assistance of ultrasound. Lubricated and non-lubricated scratch tests were performed on both novel composite coatings and on standard Ni deposits used as a benchmark coating to have an initial idea of the effect of the presence of particles within the Ni matrix. Under lubricated conditions, the performance of the Ni/hBN composite coating was very similar to the benchmark Ni coating, whereas the Ni/WS2 behaved quite differently, as the latter did not only show …

Numerical Analysis Of Time-Varying Wear With Elastic Deformation In Line Contact, Wanglong Zhan, Ping Huang

Friction

Wear is an important factor for failures of mechanical components. Current research on wear is mainly focused on experiments while the numerical simulation of wear is hardly used owing to the complexities of the wear process. Explaining the effect of friction on the wear process is important, as it will lead to a deeper understanding of the evolution of wear. This study proposed a numerical method to expound the wear process in the contact between an elastic cylinder and a half-space simulating the ring-block tester. There are two difficulties during the calculation; one is that the contact shapes vary with …

Optimal Control Of Active Nematics, Michael M. Norton, Piyush Grover, Michael F. Hagan, Seth Fraden

Department of Mechanical and Materials Engineering: Faculty Publications

In this work we present the first systematic framework to sculpt active nematic systems, using optimal control theory and a hydrodynamic model of active nematics. We demonstrate the use of two different control fields, (i) applied vorticity and (ii) activity strength, to shape the dynamics of an extensile active nematic that is confined to a disk. In the absence of control inputs, the system exhibits two attractors, clockwise and counterclockwise circulating states characterized by two co-rotating topological þ1 2 defects. We specifically seek spatiotemporal inputs that switch the system from one attractor to the other; we also examine phase-shifting perturbations. …

Microfluidic Systems With Embedded Cell Culture Chambers For High Throughput Biological Assays, Arian Jaberi, Amir Monemian Esfahani, Fariba Aghabaglou, Jae Sung Park, Sidy Ndao, Ali Tamayol, Ruiguo Yang

Department of Mechanical and Materials Engineering: Faculty Publications

The ability to generate chemical and mechanical gradients on chips is important both for creating biomimetic designs or enabling high-throughput assays. However, there is still a significant knowledge gap in the generation of mechanical and chemical gradients in a single device. In this study, we developed gradient-generating microfluidic circuits with integrated microchambers to allow cell culture and to introduce chemical and mechanical gradients to cultured cells. A chemical gradient is generated across the microchambers, exposing cells to a uniform concentration of drugs. The embedded microchamber also produces a mechanical gradient in the form of varied shear stresses induced upon cells …

Preparation Characterization And Tribological Behavior Of Lube Oil With Nanoparticles Additives, Waleed Alghani

Student Works (2020-2029)

There are many companies worldwide that would like to improve and upgrade the lube oil and enhance its performance. There is a big concern for the enhancement of lube oil by using nanotechnology and more precisely with using nanomaterial additives. Much work has made to explore and develop new sorts of lubricating oil nano-additives to diminish wear and friction in tribological configurations and to enhance surface morphology. It has noted that the use of dual nano-additives should examine the lubricating capacity and durability of lubricant. (TiO2 Anatase + Graphene) and (ZnO + Graphene) nanoparticles have selected to formulate nano-additives that …

Comparison Of Plantar Pressure Profile Of Young Adults During Training On Elliptical Devices And Overground Walking: A Pilot Study, Guilherme Manna Cesar, Thad W. Buster, Judith M. Burnfield

Department of Mechanical and Materials Engineering: Faculty Publications

Background: Elliptical training may offer advantages over other cardiorespiratory exercises for those requiring podiatric care, since its constant double-limb support diminishes recurring high-impact plantar forces while allowing exercise in a functional, upright posture. Unknown is the impact of distinct elliptical models, that can alter user’s body mechanics, on potential variations in plantar pressure patterns.

Purpose: To compare plantar pressure variables while exercising on four ellipticals and walking.

Methods: For this cross-sectional pilot study, plantar pressure data were recorded from ten young adults while exercising on four ellipticals (True, Octane, Life Fitness, SportsArt) and walking overground. One-way repeated measures ANOVA identified …

Magnetically Induced Carrier Distribution In A Composite Rod Of Piezoelectric Semiconductors And Piezomagnetics, Guolin Wang, Jinxi Liu, Wenjie Feng, Jiashi Yang

Department of Mechanical and Materials Engineering: Faculty Publications

In this work, we study the behavior of a composite rod consisting of a piezoelectric semiconductor layer and two piezomagnetic layers under an applied axial magnetic field. Based on the phenomenological theories of piezoelectric semiconductors and piezomagnetics, a one-dimensional model is developed from which an analytical solution is obtained. The explicit expressions of the coupled fields and the numerical results show that an axially applied magnetic field produces extensional deformation through piezomagnetic coupling, the extension then produces polarization through piezoelectric coupling, and the polarization then causes the redistribution of mobile charges. Thus, the composite rod exhibits a coupling between the …

Lstm-Based Anomaly Detection For Non-Linear Dynamical System, Yue Tan, Chungjing Hu, Kuan Zhang, Kan Zeng, Ethan A. Davis, Jae Sung Park

Department of Mechanical and Materials Engineering: Faculty Publications

Anomaly detection for non-linear dynamical system plays an important role in ensuring the system stability. However, it is usually complex and has to be solved by large-scale simulation which requires extensive computing resources. In this paper, we propose a novel anomaly detection scheme in non-linear dynamical system based on Long Short-Term Memory (LSTM) to capture complex temporal changes of the time sequence and make multi-step predictions. Specifically, we first present the framework of LSTM-based anomaly detection in non-linear dynamical system, including data preprocessing, multi-step prediction and anomaly detection. According to the prediction requirement, two types of training modes are explored …

The Development Of All Solid-State Optical Cryo-Cooler, Junwei Meng

Optical Science and Engineering ETDs

This dissertation describes the development of an all solid-state optical cryo-cooler. Crystals of 10% wt. ytterbium-doped yttrium lithium fluoride (Yb³⁺:YLF) are used to cool an infrared HgCdTe sensor payload to an absolute temperature below 135 K, equivalent to delta T equal 138 K below ambient. This record level of cooling is accomplished with a single stage, in a completely vibration-free environment, with a corresponding cooling power of 190 mW. This milestone is made possible by the design and fabrication of an undoped YLF thermal link that efficiently shields the payload with a non-right angle kink from intense anti-Stokes …

Spherical Cavity Expansion Approach For The Study Of Rigid-Penetrator’S Impact Problems, Mario Buchely, Alejandro Marañon

Materials Science and Engineering Faculty Research & Creative Works

In recent years, Spherical Cavity Expansion (SCE) theory has been extensively utilized to model dynamic deformation processes related to indentation and penetration problems in many fields. In this review, the SCE theory is introduced by explaining the different mathematical features of this theory, its solution, and a potential application to model the penetration of a rigid penetrator into a deformable target. First, a chronologically literature review of the most common models used to study this kind of penetration problems is introduced, focusing on the SCE theory. Then, the engineering model of penetration is presented using the SCE approach. The model …

Effects Of Polytetrafluoroethylenemicro–Particles On Mechanical Andtribological Properties Of Glass Fiberreinforced Polyoxymethylene, Kunnan Singh Jasbir Singh

Student Works (2020-2029)

Reinforcing polyoxymethylene (POM) with glass fibers (GF) enhances its mechanical properties, but at the expense of tribological performance. Formation of a transfer film to facilitate tribo–contact is compromised due to the abrasiveness of GF. As a solid lubricant, for example, polytetrafluoroethylene (PTFE) significantly improves friction and wear resistance. The effects of chemically etched PTFE micro–particles on the fiber– matrix interface of POM/GF/PTFE composites have not been systematically characterized. This research investigated the effects of PTFE micro–particles on mechanical and tribological properties of POM/GF/PTFE composites. Since PTFE is immiscible with most polymers, the surface was etched using sodium naphthalene salt dissolved …

Designing An Adjustable And Transportable Staircase, Allison Currey

Undergraduate Honors Thesis Projects

People climb stairs every day, whether it is at work, a store, or at home; however, there are populations such as people who are elderly, with pathologies, with Parkinson’s disease, or have suffered from a stroke that see climbing the stairs as a challenging task and it decreases their mobility and quality of life. Factors such as muscle weakness, strategy, and balance have been previously investigated in these populations during stair climbing. However, few studies have researched how stair climb ability, balance, and perception of difficulty are influenced by step height. The objective of this thesis is to design a …

Fatigue Damage Assessment Of Reinforced Concrete Slabs Using Integrated Dynamic Testing And Simulation, Jamadin Adiza

Student Works (2020-2029)

Assessment of existing fatigued structures is an important aspect of civil engineering infrastructure. This is critical in most loaded civil engineering structures such as bridges that are constantly subjected to dynamic loading, causing fatigue in the materials over time. Bridge deck slabs are one of the most structural elements susceptible to different cyclic loads, requiring regular checks for damage to fatigue. In order to understand the deterioration, fatigue carrying capacity and residual strength, the serviceability of the slab under the fatigue loads was not fully explored. Therefore, this research is designed to use vibration-based techniques to investigate the integrity of …

A Wirelessly Controlled Smart Bandage With 3d-Printed Miniaturized Needle Arrays, Hossein Derakhshandeh, Fariba Aghabaglou, Alec Mccarthy, Azadeh Mostafavi, Chris Wiseman, Zack Bonick, Ian Ghanavati, Seth Harris, Craig Kreikemeier-Bower, Seyed Masoud Moosavi Basri, Jordan Rosenbohm, Ruiguo Yang, Pooria Mostafalu, Dennis Orgill, Ali Tamayol

Department of Mechanical and Materials Engineering: Faculty Publications

PUBLIC ACCESS

A Novel Self-Healing System: Towards A Sustainable Porous Asphalt, Shi Xu, Xueyan Liu, Amir Tabakovic, Erik Schlangen

Articles

Self-healing asphalt, aimed to produce a sustainable asphalt pavement using green technology, has been studied in the past two decades. Technologies including encapsulated rejuvenator and induction heating have been proposed, demonstrated in the laboratory, and gradually evaluated in field application. This paper looks into the synergy effect of the above two technologies, where induction heating serves as the asphalt damage repair mechanism, requiring just 2 min heating time and encapsulated rejuvenator will replenish (rejuvenate) aged asphalt binder and reinstate bitumen’s healing ability. Moreover, the increased temperature from induction heating could in turn accelerate the diffusion process of rejuvenator into aged …

Cycle-To-Cycle Flow Variations In A Square Duct With A Symmetrically Oscillating Constriction, Erica Sherman, Lori M. Lambert, Bethany White, Michael H. Krane, Timothy Wei

Department of Mechanical and Materials Engineering: Faculty Publications

Spatially and temporally resolved Digital Particle Image Velocimetry (DPIV) measurements are presented of flow complexities in a nominally two-dimensional, symmetric, duct with an oscillating constriction. The motivation for this research lies in advancing the state-of-the-art in applying integral control volume analysis to modeling unsteady internal flows. The specific target is acoustic modeling of human phonation. The integral mass and momentum equations are directly coupled to the acoustic equations and provide quantitative insight into acoustic source strengths in addition to the dynamics of the fluid-structure interactions in the glottis. In this study, a square cross-section duct was constructed with symmetric, computer …

Electromechanics Modelling Of The Effects Of Myocardial Infarction On Left Ventricular Remodelling, Chin Neng Leong

Student Works (2020-2029)

Myocardial infarction (MI) is one of the diseases with the highest mortality rate. Following MI, myocardium experiences abrupt changes in its loading condition due to the presence of infarct. In response to such changes, myocytes undergo adaptations to maintain homeostasis. However, maladaptation can happen and lead to remodelling, in which the left ventricle (LV) gradually loses its function and eventually turns into heart failure. Nevertheless, the mechanisms underlying LV remodelling are still poorly understood. In this study, a generic LV model was developed, incorporating realistic fibre orientation and excitable contracting myocardium. It was demonstrated that the developed model is capable …

Hierarchical Mechanisms Of Lateral Interactions In High- Performance Fibers, Taylor A, Stockdale, Daniel P. Cole, Jeffrey M. Staniszewski, Michael R. Roenbeck, Dimitry Papkov, Steve R. Lustig, Youris A. Dzenis, Kenneth E. Strawhecker

Department of Mechanical and Materials Engineering: Faculty Publications

The processing conditions used in the production of advanced polymer fibers facilitate the formation of an oriented fibrillar network that consists of structures spanning multiple length scales. The irregular nature of fiber tensile fracture surfaces suggests that their structural integrity is defined by the degree of lateral (interfacial) interactions that exist within the fiber microstructure. To date, experimental studies have quantified interfacial adhesion between nanoscale fibrils measuring 10−50 nm in width, and the global fracture energy through applying peel loads to fiber halves. However, a more in-depth evaluation of tensile fracture indicates that fiber failure typically occurs at an intermediate …

Cardiorespiratory Fitness, Balance And Walking Improvements In An Adolescent With Cerebral Palsy (Gmfcs Ii) And Autism After Motor-Assisted Elliptical Training, Guilherme Manna Cesar, Thad W. Buster, Judith M. Burnfield

Department of Mechanical and Materials Engineering: Faculty Publications

Purpose: To quantify the impact of motor-assisted elliptical (ICARE) training on cardiorespiratory fitness, balance and walking function of an adolescent with walking limitations due to cerebral palsy.

Materials and methods: A thirteen-year-old boy with hemiplegic cerebral palsy (Gross Motor Function Classification System II) and autism participated. Peak oxygen consumption (peak VO₂, primary outcome measure), oxygen cost of walking, Pediatric Balance Scale (PBS), modified Timed Up and Go (mTUG), 2-Minute Walk Test (2MWT), and gait characteristics (speed, cadence, step length, single support time) were assessed prior to and after completion of 24 sessions of moderate- to vigorous- intensity ICARE …

Three-Dimensional Characterization Of Peripapillary Retinal Pigment Epithelium-Basement Membrane Layer In Patients Following Lumbar Puncture, Junfei Tong, Pengfei Dong, Sachin Kedar, Deepta Ghate, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

Purpose: To develop and test an innovative semi-automatic method for quantifying the three-dimensional morphology of the peripapillary retinal pigment epithelium-basement membrane (ppRPE/BM) layer, with application to lumbar puncture (LP) patients. Methods: Nineteen patients undergoing LP were recruited. The optic nerve head images of both eyes were acquired in 12 radial directions using optical coherence tomography (OCT) before and after LP. For each OCT image, the ppRPE/BM layer was automatically segmented with manual corrections by independent graders when necessary. The linear regression model of the ppRPE/BM layer was fitted using the least squares approach, and the ppRPE/BM layer angle was measured …

Roboticdeviceswithonboard Control And Related Systems And Devices, Shane Michael Farritor, Erik Mumm, Philip Chu, Nishant Kumar, Jason Dumpert, Yutaka Tsutano

Department of Mechanical and Materials Engineering: Faculty Publications

The embodiments disclosed herein relate to various medical device components, including components that can be incorporated into robotic and/or in vivo medical devices. Certain embodiments include various modular medical devices for in vivo medical procedures.

Role Of Interfacial Transition Zones In The Fracture Of Cu/V Nanolamellar Multilayers, Siyuan Wei, Shijian Zheng, Lifeng Zhang, Yue Liu, Jian Wang, Xianping Wang, Jiangwei Wang

Department of Mechanical and Materials Engineering: Faculty Publications

Plastic deformation and fracture behavior of Cu/V nanoscale metallic multilayers (NMMs) were systematically investigated through in situ transmission electron microscopy testing. Two different types of interfaces: sharp interfaces and interfacial transition zones (ITZs), formed in the as-fabricated Cu/V NMMs. Upon deformation, sharp interfaces and ITZs exert distinct influences on the fracture behavior of Cu/V NMMs. Sharp interfaces can impede the crack propagation by deflecting the crack propagation and blunting the crack tip, while the ITZs can induce microcracks and facilitate the fracture process. These findings shed light on the important roles of interface structures in the deformation of a broad …

Mechanical Footstep Power Generator, Mohammed Saleh Aljohani, Faisal Alonazi

All Undergraduate Projects

Mechanical Footstep Power generator

By Author: Mohammed Aljohani

Abstract

Modern technology is focusing on newer and better sources of energy. Among the important areas are power generation methods since electricity has become part of our lives. Various researchers have conducted surveys to find out the feasibility of converting renewable kinetic energy into electricity. Some of the works done in the past emphasized the selection of suitable materials and power generation systems designs that appear complicated and expensive. To ensure there is cost efficiency and energy efficiency better power generation systems need to be embraced.

The footstep power generator is a …

Low- And High-Drag Intermittencies In Turbulent Channel Flows, Rishav Agrawal, Henry C.-H. Ng, Ethan A. Davis, Jae Sung Park, Michael D. Graham, David J.C. Dennis, Robert J. Poole

Department of Mechanical and Materials Engineering: Faculty Publications

Recent direct numerical simulations (DNS) and experiments in turbulent channel flow have found intermittent low- and high-drag events in Newtonian fluid flows, at Reτ = uτh/ν between 70 and 100, where uτ, h and ν are the friction velocity, channel half-height and kinematic viscosity, respectively. These intervals of low-drag and high-drag have been termed “hibernating” and “hyperactive”, respectively, and in this paper, a further investigation of these intermittent events is conducted using experimental and numerical techniques. For experiments, simultaneous measurements of wall shear stress and velocity are carried out in a channel flow facility using hot-film anemometry (HFA) and laser …

Multi-Well Plate Channel Device With Reversible Seals, Haipeng Zhang, Timothy Wei, Sangjin Ryu

Department of Mechanical and Materials Engineering: Faculty Publications

Atherosclerosis is a cardiovascular disease which causes over 26,000 yearly deaths in the United States. This disease involves accumulation of substances in arterial walls (or plaques) that occurs frequently to arterial regions experiencing low shear stress, such as bends and bifurcations. A possible reason of plaque growth in arterial walls is the change of endothelial cell (EC)’s shape, which is related to fluid shear stresses tangentially acting on intimal layer (the EC surface) of the arterial wall. Lambert et al. studied the relationship between EC shape and shear stress (Lambert et al., 2019) using a BioFlux system (Fluxion Bioscienes) and …

Universal Mechanical Exfoliation Of Large-Area 2d Crystals, Yuan Huang, Yu-Hao Pan, Rong Yang, Li-Hong Bao, Lei Meng, Hai-Lan Luo, Yong-Qing Cai, Guo-Dong Liu, Wen-Juan Zhao, Zhang Zhou, Liang-Mei Wu, Zhi-Li- Zhu, Ming Huang, Li-Wei Liu, Lei Liu, Peng Cheng, Ke-Hui Wu, Shi-Bing Tian, Chang-Zhi Gu, You-Guo Shi, Yan-Feng Guo, Zhi Gang Cheng, Jiang-Ping Hu, Lin Zhao, Guan-Hua Yang, Eli Sutter, Peter Sutter, Ye-Liang Wang, Wei Ji, Xing-Jiang Zhou, Hong-Jun Gao

Department of Mechanical and Materials Engineering: Faculty Publications

Two-dimensional materials provide extraordinary opportunities for exploring phenomena arising in atomically thin crystals. Beginning with the first isolation of graphene, mechanical exfoliation has been a key to provide high-quality two-dimensional materials, but despite improvements it is still limited in yield, lateral size and contamination. Here we introduce a contamination-free, one-step and universal Au-assisted mechanical exfoliation method and demonstrate its effectiveness by isolating 40 types of single-crystalline monolayers, including elemental two-dimensional crystals, metal-dichalcogenides, magnets and superconductors. Most of them are of millimeter-size and high-quality, as shown by transfer-free measure- ments of electron microscopy, photo spectroscopies and electrical transport. Large sus- pended …

Benign Ferroelastic Twin Boundaries In Halide Perovskites For Charge Carrier Transport And Recombination, Xun Xiao, Wenhao Li, Yanjun Fang, Ye Liu, Yuchuan Shao, Shuang Yang, Jingjing Zhao, Xuezeng Dai, Rashid Zia, Jinsong Huang

Department of Mechanical and Materials Engineering: Faculty Publications

Grain boundaries have been established to impact charge transport, recombination and thus the power conversion efficiency of metal halide perovskite thin film solar cells. As a special category of grain boundaries, ferroelastic twin boundaries have been recently discovered to exist in both CH3NH3PbI3 thin films and single crystals. However, their impact on the carrier transport and recombination in perovskites remains unexplored. Here, using the scanning photocurrent microscopy, we find that twin boundaries have negligible influence on the carrier transport across them. Photoluminescence (PL) imaging and the spatial-resolved PL intensity and lifetime scanning confirm the electronically benign nature of the twin …

Variations In Plantar Pressure Variables Across Elliptical Trainers In Older Adults, Judith M. Burnfield, Guilherme Manna Cesar, Thad W. Buster

Department of Mechanical and Materials Engineering: Faculty Publications

Background: Ellipticals are used to address walking and cardiorespiratory training goals of older adults, some of whom are at risk for foot injuries. Variations in joint kinematics and muscle demands when using different ellipticals could lead to plantar pressure differences. This study explored plantar pressure variables during gait and use of four ellipticals.

Methods: Plantar pressures were recorded while 10 adults [68.1 (4.5) years] walked and used the True, Octane, Life Fitness, and SportsArt ellipticals. Repeated-measures ANOVAs (5 × 1) identified forefoot and heel differences across conditions.

Findings: Maximum forefoot forces and peak pressures were significantly lower than walking for …

Multiscale Modeling Of Carbon Fibers/Graphene Nanoplatelets/Epoxy Hybrid Composites For Aerospace Applications, Hashim Al Mahmud

Dissertations, Master's Theses and Master's Reports

Significant research effort has been dedicated for decades to improve the mechanical properties of aerospace polymer-based composite materials. Lightweight epoxy-based composite materials have increasingly replaced the comparatively heavy and expensive metal alloys used in aeronautical and aerospace structural components. In particular, carbon fibers (CF)/graphene nanoplatelets (GNP)/epoxy hybrid composites can be used for this purpose owing to their high specific stiffness and strength. Therefore, this work has been completed to design, predict, and optimize the effective mechanical properties of CF/GNP/epoxy composite materials at different length scales using a multiscale modeling approach. The work-flow of modeling involves a first step of using …

Increasing Access To Pv Technology Through Sustainable Racking: A Review Of Existing Literature And Ground Mounted Fixed Tilt Designs, And What Can Be Done Next, Parijata Prabhakara

Dissertations, Master's Theses and Master's Reports

There is a lack of literature on the structural balance of systems (BOS), also called racking, for ground mount, fixed-tilt solar PV systems. Literature that exists discusses mostly rooftop racking and installations, additional wind loading, and weight considerations imposed on roofs, and little guidance is provided in building codes. The lack of peer-reviewed guidance on design requirements for domestic and large-scale application solar PV racking systems leaves most consumers relying on expensive, patented, off-the-shelf hardware. As PV cell technology and module costs have improved, we can start to focus on PV BOS improvements (particularly racking) and move towards sustainable designs …