Mechanical Engineering Commons^™

Creep Behavior Of A Ti-Based Multi-Principal Element Alloy, Benjamin Elbrecht

All Theses

Abstract

The understanding of microstructural damage mechanisms is the foundation of better understanding existing materials and future material development. There are significant challenges to measuring these damage mechanisms in-situ as continuous observation of the state of the microstructure is difficult or impossible for many experimental setups. This thesis presents a method for measuring grain boundary sliding (GBS) and local strain concentrations in-situ via a Heaviside function based algorithm. GBS is the shearing of two grains along their shared grain boundary and is a common damage mechanism in creep which presents as a discontinuity that can be measured with a Heaviside …

Manufacturing And Characterization Of Continuous Nanofiber-Reinforced Composites, Lucas Barry

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Fiber-reinforced composite laminates are some of the most advanced structural materials available. However, delamination remains a critical challenge due to its prevalence in structures and ability to cause catastrophic failure. Recently, high-temperature composites are at the forefront of polymer-matrix composites research, but they are prone to microcracking followed by delamination. Nanoreinforcement of interfaces by continuous nanofibers has been proposed earlier at UNL and produced increased interlaminar fracture resistance in conventional advanced composites. However, no studies have yet been conducted on emerging high-temperature composites. Also, there is insufficient information on the translatability of observed modes I and II interlaminar fracture toughness …

Role Of Structural Hierarchy In Multiscale Material Systems, Siavash Sattar

Mechanical & Aerospace Engineering Theses & Dissertations

Multiscale material systems derive their effective mechanical properties through a hierarchical organization of their structural elements and components. The hierarchy of a material is related to its effective properties, material processing, and composition. The hierarchy can be defined as an identifiable structural component with a specific size scale, such as the individual fibers collimated into platelets arranged randomly and producing a complex composite system or the lamellar structure in freeze-casted ceramic with the variation of in-plane orientation. In this study, the role of the structural hierarchy on the effective mechanical response and failure behavior of three complex material systems was …

Passive Prosthetic Ankle Design Based On Indonesian Anthropometry, Wahyu Dwi Lestari

Journal of Mechanical Engineering Science and Technology (JMEST)

Foot prosthesis is a replacement for the foot to overcome activity limitations due to disease, birth defects, accidents, or amputations. Many foot prosthetics have been developed in recent years to treat patients. However, prostheses on the market today have drawbacks, including their high price, lack of comfort, stiff ankles, and low durability. The main objective of this study is to develop an existing ankle-foot prosthesis design that approximates the resemblance of a human foot according to the anthropometry of Asians, especially Indonesians. This study contains the design of a prosthetic foot with a skin design model and a support core. …

Surface Quality Of Fe, Ni And Cr Added Hyper-Eutectic Al-Si Automotive Alloys Under Up-Milling And Down-Milling Operation, Akib Abdullah Khan, Mashiur Rahman Shoummo, Mohammad Salim Kaiser

Journal of Mechanical Engineering Science and Technology (JMEST)

Effect of the elements Fe, Ni, and Cr on the surface quality under machining of hyper-eutectic aluminiumbased Al-Si automotive alloys has been carried out as the elements improve the properties of this alloy. Machining is done on a horizontal type milling machine using a high-speed steel slab milling cutter in dry condition. Only the cutting speed varies throughout the experiment, while the machining feed and depth of cut remain fixed. The experimental results show that the addition of these alloying elements increases the roughness and hardness specially due to formation of Fe-rich intermetallic ��-����5��������. However, the needle-like ��-����5�������� has been …

Effect Of Variation Of Sic Mass Fraction On Mechanical Properties Of Al-Sic Composite Using Stir Casting Method, Sumarji Sumarji, Naufal Fardio Albajili, Mahros Darsin, Rahma Rei Sakura, Andi Sanata

Journal of Mechanical Engineering Science and Technology (JMEST)

Al-SiC is a composite composed of AA6061 as a matrix and SiC as a reinforcement particle. The variation of mass added will affect the mechanical properties of the composite because Al-SiC is hardenable, which means that its mechanical properties can be improved by adding the reinforcement component. However, an excessive portion of SiC leads to a decrease in mechanical properties. The purpose of this study was to find the optimal composition of the addition of SiC into the aluminium matrix to gain maximum tensile strength and hardness. The mass fraction variation that would be used in this composite was the …

Effect Of Homogenization Pressure On Bacterial Cellulose Membrane Characteristic Made From Pineapple Peel Waste, Muhamad Muhajir, Heru Suryanto, Yanuar Rohmat Aji Pradana, Uun Yanuhar

Journal of Mechanical Engineering Science and Technology (JMEST)

Many studies were conducted to maintain the environment by reducing the waste, especially pineapple peel waste. This study aims to explore the effect of various pressure of the homogenization process on bacterial cellulose membrane surface morphology and structure produced using extract of pineapple peel waste. The methods include the preparation of pellicle samples from the product of the fermentation process of Acetobacter xylinum using a medium from the extract of pineapple peel waste. Bacterial cellulose pellicles were crushed using a blender. Mashed bacterial cellulose pellicle was homogenized in High-Pressure Homogenizer with pressure variation of 150 bar, 300 bar, 450 bar, …

Machine Vision For The Various Road Surface Type Classification Based On Texture Feature, Susi Marianingsih, Widodo Widodo, Marla Sheilamita S. Pieter, Evanita Veronica Manullang, Hendry Y. Nanlohy

Journal of Mechanical Engineering Science and Technology (JMEST)

The mechanized ability to specify the way surface type is a piece of key enlightenment for autonomous transportation machine navigation like wheelchairs and smart cars. In the present work, the extracted features from the object are getting based on structure and surface evidence using Gray Level Co-occurrence Matrix (GLCM). Furthermore, K-Nearest Neighbor (K-NN) Classifier was built to classify the road surface image into three classes, asphalt, gravel, and pavement. A comparison of KNN and Naïve Bayes (NB) was used in present study. We have constructed a road image dataset of 450 samples from real-world road images in the asphalt, gravel, …

Gasohol Engine Performance With Various Ignition Timing, Hendry Y. Nanlohy, Suyatno Suyatno, Helen Riupassa, Marthina Mini, Trismawati Trismawati, Mebin Panithasan

Journal of Mechanical Engineering Science and Technology (JMEST)

Experimental research has been conducted on the effect of ignition timings on the characteristics and performance of gasohol engines such as power, torque, specific fuel consumption, and thermal efficiency. The fuel used in this research is pure gasoline and a mixture of 50% bioethanol (BE50). The results show that the ignition timing that gives the maximum effect occurs at the top and bottom dead points of 9 degrees for gasoline and 12 degrees for BE50 fuel. Furthermore, the maximum power is obtained at 6,500 rpm, and at an ignition time of 12 degrees BTDC the maximum power generated is 4.63 …

Bbt Acoustic Alternative Top Bracing Cadd Data Set-Norev-2022jun28, Bill Hemphill

STEM Guitar Project’s BBT Acoustic Kit

This electronic document file set consists of an overview presentation (PDF-formatted) file and companion video (MP4) and CADD files (DWG & DXF) for laser cutting the ETSU-developed alternate top bracing designs and marking templates for the STEM Guitar Project’s BBT (OM-sized) standard acoustic guitar kit. The three (3) alternative BBT top bracing designs in this release are
(a) a one-piece base for the standard kit's (Martin-style) bracing,
(b) 277 Ladder-style bracing, and
(c) an X-braced fan-style bracing similar to traditional European or so-called 'classical' acoustic guitars.

The CADD data set for each of the three (3) top bracing designs includes …

Predictive Thermal Modeling And Characterization Of Ultrasonic Consolidation Process For Thermoplastic Composites, Madeline Kirby

LSU Master's Theses

Ultrasonic consolidation (USC) of thermoplastic composites (TPCs) is a highly attractive and promising method to manufacture high-performance composites. This work focuses on USC of dry carbon fiber (CF) fabrics with high-temperature polyphenylene sulfide (PPS) films. Experimental trials to assess feasibility of the process are time-consuming. Consequently, a predictive thermal model would facilitate process parameters selection to reduce expensive trial-and-error approaches. This paper presents a 2D finite element model of samples under consolidation, incorporating equations for viscoelastic heating, matrix phase change, and material properties. Theoretical temperature profiles for nodes of interest were compared to the corresponding experimental temperature curves for various …

Effects Of Pulsatile Flow Rate And Shunt Ratio In Bifurcated Distal Arteries On Hemodynamic Characteristics Involved In Two Patient-Specific Internal Carotid Artery Sidewall Aneurysms: A Numerical Study, Hang Yi, Mark Johnson, Luke C. Bramlage, Bryan Ludwig, Zifeng Yang

Mechanical and Materials Engineering Faculty Publications

The pulsatile flow rate (PFR) in the cerebral artery system and shunt ratios in bifurcated arteries are two patient-specific parameters that may affect the hemodynamic characteristics in the pathobiology of cerebral aneurysms, which needs to be identified comprehensively. Accordingly, a systematic study was employed to study the effects of pulsatile flow rate (i.e., PFR−I, PFR−II, and PFR−III) and shunt ratio (i.e., 75:25 and 64:36) in bifurcated distal arteries, and transient cardiac pulsatile waveform on hemodynamic patterns in two internal carotid artery sidewall aneurysm models using computational fluid dynamics (CFD) modeling. Numerical results indicate that larger PFRs can cause higher wall …

Large Area Projection Sintering Of Semicrystalline Polymers And Part Analysis Of The Printed Specimens, Taranjot Kaur

USF Tampa Graduate Theses and Dissertations

As the requirements posed to products have increased in recent years. The trend towards individualized serial products steps up the need for respective manufacturing techniques to be more and more flexible. Conventional techniques of serial production, such as injection molding, are unable to fully meet the requirements of this trend. Additive manufacturing techniques generate components directly from a CAD data set while requiring no specific mold, producing minimal waste, and reaching satisfactory geometric accuracy. This is how, as opposed to conventional techniques, they comply with these increased demands to processing technology. Over the last two decades, the research community has …

Effect Of Dispersions Of Al2o3 On The Physical And Mechanical Properties Of Pure Copper And Copper-Nickel Alloy, Samah El-Khatib, A. H. Elsayed, A. Y. Shash, A. El-Habak

Future Engineering Journal

This paper illustrates the mechanical and physical properties of pure Cu and Cu-Ni (50-50 wt. %) alloy mixed with Al₂O₃ (1-4 wt. %) as micro-particles reinforcement materials. The attained composite alloy specimens' characteristics were estimated such as microstructure, relative density, electrical and thermal conductivity, hardness, and compression yield stress properties to adjust the suitable optimum percentage of reinforcing material which has the best physical and mechanical properties with different main matrix materials whether pure Cu powder or Cu-Ni mechanical alloy. The micron-sized Al₂O₃ was added to enhance the mechanical and physical properties of the …

Bbt Side Mold Assy, Bill Hemphill

STEM Guitar Project’s BBT Acoustic Kit

This electronic document file set covers the design and fabrication information of the ETSU Guitar Building Project’s BBT (OM-sized) Side Mold Assy for use with the STEM Guitar Project’s standard acoustic guitar kit. The extended 'as built' data set contains an overview file and companion video, the 'parent' CADD drawing, CADD data for laser etching and cutting a drill &/or layout template, CADD drawings in AutoCAD .DWG and .DXF R12 formats of the centerline tool paths for creating the mold assembly pieces on an AXYZ CNC router, and support documentation for CAM applications including router bit specifications, feeds, speed, multi-pass …

New Advances In Fluid–Structure Interaction, Wenli Chen, Zifeng Yang, Gang Hu, Haiquan Jing, Junlei Wang

Mechanical and Materials Engineering Faculty Publications

Fluid–structure interactions (FSI) play a crucial role in the design, construction, service and maintenance of many engineering applications, e.g., aircraft, towers, pipes, offshore platforms and long-span bridges. The old Tacoma Narrows Bridge (1940) is probably one of the most infamous examples of serious accidents due to the action of FSI. Aircraft wings and wind-turbine blades can break because of FSI-induced oscillations. To alleviate or eliminate these unfavorable effects, FSI must be dealt with in ocean, coastal, offshore and marine engineering to design safe and sustainable engineering structures. In addition, the act of wind on plants and its resultant wind-induced motions …

Tini-Based Bi-Metallic Shape-Memory Alloy By Laser-Directed Energy Deposition, Yitao Chen, Cesar Ortiz Rios, Braden Mclain, Joseph William Newkirk, Frank W. Liou

Materials Science and Engineering Faculty Research & Creative Works

In this study, laser-directed energy deposition was applied to build a Ti-rich ternary Ti–Ni–Cu shape-memory alloy onto a TiNi shape-memory alloy substrate to realize the joining of the multifunctional bi-metallic shape-memory alloy structure. The cost-effective Ti, Ni, and Cu elemental powder blend was used for raw materials. Various material characterization approaches were applied to reveal different material properties in two sections. The as-fabricated Ti–Ni–Cu alloy microstructure has the TiNi phase as the matrix with Ti2Ni secondary precipitates. The hardness shows no high values indicating that the major phase is not hard intermetallic. A bonding strength of 569.1 MPa was obtained …

Evaluating The Effects Of Granulated Rubber And Glass Fibers In Polymer Concrete As A Structural Material For Wafer Grinding Machines, Kevin Gabriel Kuehn, Philip Randall Streeter

Materials Engineering

Polymer concrete is a composite material used to replace cast iron and steel in wafer grinding machines for vibration damping. During the grinding and lapping processes of manufacturing silicon wafers, excessive vibrations may cause subsurface damage which requires additional polishing and reduces yield. Nine compositions containing various levels of granulated rubber and glass fibers were manufactured. CRM WRF-10 granulated rubber was examined at 0%, 5%, and 10% and Corning Cem-Fil glass fibers were added at 0%, 0.5%, and 1% by weight. Smooth-On EpoxAcast 690 epoxy resin was held constant at 16% for each composition. Crushed granite aggregate from Martin Marietta, …

Model-Based Design Of An Optimal Lqg Regulator For A Piezoelectric Actuated Smart Structure Using A High-Precision Laser Interferometry Measurement System, Grant P. Gallagher

Master's Theses

Smart structure control systems commonly use piezoceramic sensors or accelerometers as vibration measurement devices. These measurement devices often produce noisy and/or low-precision signals, which makes it difficult to measure small-amplitude vibrations. Laser interferometry devices pose as an alternative high-precision position measurement method, capable of nanometer-scale resolution. The aim of this research is to utilize a model-based design approach to develop and implement a real-time Linear Quadratic Gaussian (LQG) regulator for a piezoelectric actuated smart structure using a high-precision laser interferometry measurement system to suppress the excitation of vibratory modes.

The analytical model of the smart structure is derived using the …

Ecological Risk Assessment For Coal Combustion Residuals And Herrington Lake Adjacent To The Kentucky Utilities E.W. Brown Generating Station, Mary Sorensen, Alex Smith, Mark Nielsen

World of Coal Ash Proceedings

No abstract provided.

Epri Research On Groundwater-Surface Water Interactions Near Coal Combustion Product Sites, Bruce Hensel, Jeff Thomas, Tim Towey, Anthony Aufdenkampe

World of Coal Ash Proceedings

No abstract provided.

Cqa - A Common Sense Approach At Becoming The Mvp On Your Next Project, James Price, Michael Fisher, John Metcalf

World of Coal Ash Proceedings

No abstract provided.

Challenges & Pragmatic Solutions For The Design And Construction Of A 300-Acre Ccr Landfill Located In The Southwestern Us - A Case Study, Andy Lucas, Jason Pokorny

World of Coal Ash Proceedings

No abstract provided.

State Of The Practice For Compaction Quality Of Dry Stack Ccr Storage Facilities, Bruce Cunningham, Pavana Vennapusa, David J. White, Robert Eric Hageman

World of Coal Ash Proceedings

No abstract provided.

Groundwater Compliance & Strategy Insights For Ccr Rule Stakeholders, Sheryl Smith, Mark Johnson

World of Coal Ash Proceedings

No abstract provided.

Hybrid Closure Approach: Constructing Bidding Lessons Learned, Brian Harthun, P.E.

World of Coal Ash Proceedings

No abstract provided.

Ccr Landfill Construction & Operation Under Subtitle D, Thomas R. Gredell

World of Coal Ash Proceedings

No abstract provided.

Hybrid Closure Approach: Design Investigation Review, Brian Sperrazza, P.E., P.G.

World of Coal Ash Proceedings

No abstract provided.

Geochemical Explanations For Strong Natural Attenuation Of Molybdenum, Selenium, And Lithium In A Groundwater Plume, Jacob Chu, J. P. Brandenburg

World of Coal Ash Proceedings

No abstract provided.

Construction Risk Management Considerations For Ccr Surface Impoundment Closures, John P. Seymour, Chris Robb

World of Coal Ash Proceedings

No abstract provided.