Mechanical Engineering Commons^™

Quasi-Static Compression Performance Of Three Subscale Origami-Inspired Carbon Fiber Reinforced Polymer, Chase Mortensen

Student Research Symposium

Sandwich-structured composites are made of a lightweight core material between two thin composite panels. Variants of the Ori-Miura folding pattern have been investigated and compared to both the traditional Miura folding pattern (Fig. 1) and the more commonly used core design, the honeycomb. While the honeycomb design is favored over the Miura folding pattern and its variants due to its simple shape and better performance in compression, honeycomb cores also present drawbacks that are detrimental to the integrity of the sandwich structure. These drawbacks include, but are not limited to:

• Honeycomb cores consist of closed channels trapping moisture and heat. …

The Aerodynamic Levitator Project, Noah Brown

Undergraduate Research Conference at Missouri S&T

After the development and successful demonstration of a hyperbaric aerodynamic levitator, work to redesign the nozzle was proposed for increasing levitation height and stability. The goal of this eight-week summer research project was to create a CFD model to aid in the optimization of this nozzle. This was to be accomplished by using ANSYS Fluent to first replicate experimental data found in a research paper to assess its validity. Next, the model was to be modified for use on the levitator project and then used to analyze the current nozzle design. Afterwards, Steps will be taken to make alterations to …

Globular Protein For Surface Modification Of Cellulosecontaining Materials, Nodira Saydaliyeva

Technical science and innovation

The purpose of this work is the chemical modification of cotton fabrics with natural globular protein. Modification was carried out in the process of finishing cotton fabrics, after decoction and bleaching in a continuous mode. The effect of modification on the strength, protein content and functional groups of cotton fabric has been studied. According to the results obtained using the AUTOGRAPH AGS-N machine, it was found that the modification of cotton fabrics with a solution of globular protein increases the strength of the treated fabrics, depending on the concentration of the modifier and the temperature regime. Treatment with a highly …

Thermo-Elasto-Plastic Stability Of Biaxially Loaded Hollow Rectangular Section Steel Beam-Columns With Applied Torsion, George Adomako Kumi

Civil & Environmental Engineering Theses & Dissertations

Presented herein is an experimental and theoretical study of biaxially loaded hollow rectangular section steel beam-columns with applied torsion at elevated temperatures. The theoretical analysis is based on a system of simultaneous materially nonlinear differential equations of equilibrium for which an iterative semi-analytic solution approach is formulated. Although the primary goal of this research is to study the influence of elevated temperatures on the steel member with the complex loading, rigorous analysis is also conducted of the member at ambient temperature for comparison. The experimental part of the study involves conducting tests on the members at both ambient and high …

Segregation And Heat Treatment Response Of Cast Quench And Partition Steels, Mujeeb Hussain Shaik

Masters Theses

Quench and partition (Q&P) steels have emerged as promising alternatives to traditional quenching and tempering methods, offering a superior balance of strength and ductility due to their unique microstructure of martensite, and retained austenite. This literature review examines the development and optimization of Q&P steels, focusing on their mechanical properties, heat treatment processes, and applications in various industries. This study explores the application and effectiveness of the Quench and Partition (Q&P) heat treatment process on cast steels and examines segregation phenomena in cast medium Mn steels. Medium Mn steels were employed for various Q&P cycles on cast specimens to investigate …

Safety Evaluation Of Hawaii Dot Modified Type A-1 Flared Buried In Backslope Guardrail End Terminal, Sina Changizian

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The Hawaii Department of Transportation (HDOT) desired to evaluate the crashworthiness of a guardrail end terminal design in which the upstream guardrail anchorage was connected to a block partially buried in a cut slope, known as a “Buried in Backslope” or BIB design. The HDOT BIB system used an upper W-beam with 8-in. deep blockouts attached to W6x9 steel posts and a lower W-beam rubrail located 3 in. below the upper rail. The system used two horizontal flares: 7.4:1 near the upstream anchor block and a 13:1 flare through the ditch.

Critical impact points (CIPs) were identified and recommended for …

Finite Element Analysis Of Thermal-Mechanical Instabilities In Nonmetallic Friction Composite Material, Joseph-Shaahu Shaahu

Electronic Theses and Dissertations

Thermal-mechanical instability (TMI) has been a research topic of interest as it focuses a lot on transportation systems. Thermal-mechanical instability was first noticed in railway and experimentally studied with a pin-to-pin or pin-to-surface setup of sliding contact. The topic has been extended into brakes and clutches which are two of the most common sliding systems most susceptible to thermal buckling and thermoelastic instability (TEI), where thermal buckling and thermoelastic instability are two sub-categories of thermal-mechanical instability. Thermal-mechanical instability is an ongoing research to better understand the phenomenon and the limits at which such instability occurs. This work delved into the …

A Study On High-Frequency Bending Fatigue, Microhardness, Tensile Strength, And Microstructure Of Parts Made Using Atomic Diffusion Additive Manufacturing (Adam) And Additive Friction Stir Deposition (Afsd), Hamed Ghadimi

LSU Doctoral Dissertations

This dissertation reports the findings of several studies on the mechanical and microstructural properties of parts made using atomic diffusion additive manufacturing (ADAM) and additive friction stir deposition (AFSD). The design of a small-sized bending-fatigue test specimen for an ultrasonic fatigue testing system is reported in Chapter 1. The design was optimized based on the finite element analysis and analytical solution. The stress–life (S–N) curve is obtained for Inconel alloy 718. Chapter 2 presents the findings of ultrasonic bending-fatigue and tensile tests carried out on the ADAM test specimens. The S-N curves were created in the very high-cycle fatigue regime. …

A 3d Imaging-Based Critique Of Wire Arc Additive Manufacturing (Waam) Simulations, Omar Oraby

Theses and Dissertations

Residual stresses play a critical role in the mechanical behavior and structural integrity of engineered components. Understanding and quantifying these stresses are essential for ensuring the reliable performance and durability of materials and structures. Traditionally destructive methods are used that involve sample sectioning and material removal. However, non-destructive methods have gained popularity due to their advantages in preserving the specimen's integrity for further testing and material waste reduction. Among these techniques, Digital Image Correlation (DIC) stands out as a powerful non-contact and full-field measurement approach. DIC captures displacements and strain distributions by analyzing the deformation of speckle patterns on the …

Balsa Bridge, Caleb T. Lovett

All Undergraduate Projects

The problem presented throughout this report was to create a small-scale bridge made entirely out of balsa wood and glue, that could withstand substantial force, as well as perform a lifting/lowering cycle. Other requirements associated with the bridge were properties of weight, deflection, size, and shape. This problem presented a challenge that tested the mathematical side of engineering, being strongly reliant on statics, mechanics of materials, and mechanical design analyses.

To approach this problem, the first step was to complete in depth calculations of the chosen design. With this done, manufacturing and assembly was able to be completed. With a …

Deep Learning Based Optical Flow Analysis Of High-Speed Flows, Daniel H. Zhang, Zifeng Yang

Mechanical and Materials Engineering Faculty Publications

Two-dimensional Rayleigh scattering imaging is utilized to quantify the high-speed flow velocity by employing deep learning based optical flow analysis, along with density fields from Rayleigh scattering intensity profiles.

Kissing Bond Assessment In Adhesive Bonded Carbon Fiber Reinforced Composites Using Dielectric Spectroscopy, Minhazur Rahman

Mechanical and Aerospace Engineering Dissertations - Archive

The widespread use of fiber-reinforced composites in industries such as space, aviation, automobiles, and construction necessitates the formation of robust composite joints between critical structural components. Although adhesive-bonded joints are superior with improved load distribution and reduced weight, they are often overlooked in favor of bolted joints and mechanical fasteners due to the lack of reliable Non-Destructive Evaluation (NDE) techniques for adhesive-bonded composites. The anisotropic nature of the substrate and the intricate interfacial interactions between the adherend and adhesive material present significant challenges for conventional NDE methods. Moreover, weak adhesive bonds can result from uncontrolled manufacturing parameters, such as accidental …

Experimental Investigations And Optimization Of 3d Printed Cellular Structures For Protection Against Traumatic Brain Injury, Aaron R. Jackson

Mechanical and Aerospace Engineering Dissertations - Archive

Traumatic Brain Injury (TBI) disrupts brain function due to head impacts, blast exposures, and ballistic penetrations. It is a significant cause of mental health issues and disability, particularly among military personnel. Historically, combat helmets were designed primarily to protect against fragments. However, recent data highlights the need for helmets that also protect against blast and blunt impacts. Effective TBI prevention requires helmets that address various energy threats while remaining lightweight. A critical metric in this effort is head acceleration, which is closely linked to injury across different scales of brain damage.

Four lattice structures were 3D printed using Digital ABS …

Synthesis Of Ni-Based Intermetallics By Electrolytic Plasma Processing Of Ti And Ti-Based Alloys, Chuzhong Zhang

Material Science and Engineering Dissertations - Archive

EPP is an innovative surface modification technique that enables the deposition of metal ions from the electrolyte and their integration with substrate atoms to form intermetallic compound surface layers. EPP offers advantages such as high deposition rates, environmental cleanliness, and operational simplicity. In this study, Ni-Ti intermetallic layers were successfully synthesized on a Ti-6Al-4V substrate using EPP. The properties of the resulting Ni-Ti intermetallic layers were characterized using SEM, EDS, XRD, TEM, nanoindentation, and tribology tests.

This work aims to understand the fabrication mechanism and investigate the effects of various processing parameters on the EPP process. Key factors such as …

Generalizable Fugitive Carrier Method For 3d Printing Of Hydrogels, Hakan Arslan

Mechanical and Aerospace Engineering Dissertations - Archive

Hydrogels, with physical characteristics resembling biological soft tissues, hold great potential for bioinspired and biomedical applications. However, using them in additive manufacturing systems has challenges because of their poor mechanical and rheological properties. In response to these challenges, we introduce a fugitive carrier method, a novel and generalizable approach for materials incompatible with pneumatic-based extrusion three-dimensional (3D) printers. Our developed fugitive carrier method allows the 3D printing of a broad spectrum of hydrogel precursors with low viscosity while retaining their inherent properties. This technique has been successfully demonstrated by creating biomimetic structures with anisotropic and programmable systems utilizing temperature-sensitive hydrogel …

Generating Blood Analog For Laser Induced Fluorescent Particle Image Velocimetry, Chungyiu Ma, Jared Chong, Hang Yi, Zifeng Yang, Luke Bramlage, Bryan Ludwig

Mechanical and Materials Engineering Faculty Publications

To mimic blood non-Newtonian viscosity features under designated temperatures from 305 to 315 K, transparent blood analogs were generated by the mixture of xanthan gum and deionized water with fluorescent particles for laser induced fluorescent particle image velocimetry.

Graphene Reinforced Polymer Composite For Small-Scale Vertical Axis Wind Turbine Rotors, Kunal A. Bachim

Mechanical and Aerospace Engineering Theses - Archive

Polymers have evolved as an indispensable asset in various sectors ranging from packaging and construction to energy and aerospace. However, the accumulation of polymer waste poses a necessity to shift toward sustainable waste management processes. Mechanical recycling is a primary method in establishing a circular economy approach for polymers. However, a fundamental challenge arises in this process: a decrease in the mechanical performance of the recycled product compared to that of its pristine counterpart.

This project addresses the challenge of enhancing the recyclability of polyethylene terephthalate (PET) from discarded polymer material by incorporating graphene nanoparticles into the polymer matrix during …

3d Flow Field Quantification In An Artery Model Using Optical Flow Method Based On Simulated Multi-Angle Angiography, Zifeng Yang, Hang Yi, Luke Bramlage, Bryan Ludwig

Mechanical and Materials Engineering Faculty Publications

3D flow field in a numerically simulated arterial model is quantified using the three-dimensional optical flow method based on simulated simultaneous multi-angle X-ray angiography of the blood flow with contrast agent perfusions.

Strategies To Mitigate Efflorescence In Walls Constructed Using Clays Bricks; A Review Article, Marwa Abdulkareem. Anber, Soran Abdulrahman Ahmad, Naros Rahman Mahmoud, Kawan Fuoad. Kayani, Mohammed Ali Abdulrehman

Al-Esraa University College Journal for Engineering Sciences

_{The construction of buildings, especially residential housing for communities, is a significant industry on a global scale. Masonry units such as bricks, blocks, and stones are often utilized materials. Bricks are highly regarded because to their widespread availability, cost-effectiveness, and excellent insulating capabilities. Nevertheless, the presence of efflorescence presents a difficulty in the construction of brick walls. Efflorescence refers to the process in which salts move to the outer layer of the brick, resulting in the formation of white deposits and negatively impacting its visual appeal. Efflorescence is caused by various circumstances, such as the existence of salts in bricks, …}

The Importance Of Cryptography In Cloud Computing, Saja Alaam Talib

Al-Esraa University College Journal for Engineering Sciences

Cloud computing has grown as a widely accepted concept simultaneously, as the alarms for the security of data and information. This paper seeks to establish the comprehensive roles of cryptography in tackling these issues in the Cloud environment. The study begins with the historical background of cryptography and then moves on to analyze trends in information technology before discussing on the challenges to security in cloud computing. The goal of its publication is to highlight the importance of using cryptographic technologies for the protection of information confidentiality, its integrity and compliance. The combination of literature review and the case study …

A Concept Of Producing Aluminum In-Situ On The Moon Through Molten Salt Electrolysis, Jacob N. Ortega, Jeffrey Smith, Fateme Rezaei, David Bayless, William Schonberg, Daniel Stutts, Daoru Han

Materials Science and Engineering Faculty Research & Creative Works

This paper presents a concept of producing aluminum in-situ on the lunar surface, namely, the Lunar In-Situ Aluminum Production through Molten Salt Electrolysis (LISAP-MSE) method developed at Missouri University of Science and Technology. This paper aims to demonstrate the use of electro-deoxidation to reduce aluminum oxide (i.e., alumina) into aluminum and oxygen gas via electrolysis in a molten salt bath for the production of aluminum on the Moon. It is shown that with a steady supply of hydrogen chloride, this in-situ resource utilization (ISRU) method could supply several necessary materials consumed in the electro-deoxidation process except hydrogen chloride to produce …

Phenolic Polymer Infiltration And Pyrolysis Process For Additively Manufactured Carbon/Peek Composites To Produce Carbon–Carbon Composites, S. Weiler, H. A. Haffner, K. Chandrashekhara, J. Watts, G. E. Hilmas, J. Bayldon, L. M. Rueschhoff

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Carbon–carbon composites are carbon fibers reinforced with carbon matrix and are classified as advanced materials well suited for high-temperature structural applications. Carbon–carbon composites are characterized by maintaining excellent mechanical properties and structural stability at high temperatures and have been used in aerospace application as nozzles, heatshields, and leading edge. However, conventional methods to manufacture carbon–carbon composites are costly and time-consuming. the aim of this work is to develop a method for creating additively manufactured (AM) carbon–carbon composites using a high-pressure re-infiltration process. in doing so, less infiltration cycles are required compared to a low-pressure re-infiltration, reducing the total manufacture time. …

Damage Initiation Of 15v38 Steel Bar During Square-To-Round Hot Rolling Process, Siva Sai Krishna Dasari, Henry Adekola Haffner, K. Chandrashekhara, Mario F. Buchley, Simon N. Lekakh, Ronald J. O'Malley

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Hot rolling processes have been extensively used to produce round bars by reducing the cross-sectional area of continuously cast steel. The current trend toward increasing productivity often requires a more aggressive reduction per pass. Establishing safe and optimized hot rolling parameters must be determined to avoid damage while deforming the specific steel composition. Understanding the damage mechanism during the metal forming process is vital for product quality. Herein, a combined experimental and simulation approach is developed to track the evolution potential damage during hot bar rolling. Hot tension tests are conducted on as-cast vanadium micro alloyed 15V38 steel at different …

Electrostatic Sorting Of Lunar Regolith Simulants For Sustainable Resource Utilization: Modeling And Characterization Of Particle Size Distribution, Abdullah Al Moinee, Peter Bachle, Kyle Newport, William Schonberg, David Bayless, Jeffrey Smith, Daoru Han, Fateme Rezaei

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In pursuit of sustainable resource utilization on the Moon, this paper delves into modeling and characterization of particle size distribution (PSD) of lunar regolith simulants in an electrostatic system. A prototype electrostatic sieve was built and tested with four sample simulants mirroring properties of lunar mare and highland regolith. An alternating four-phase (90 degrees, 180 degrees, 270 degrees, 360 degrees) traveling square-wave was utilized for particle-directed transport to model the diverse trajectories of the particles. Numerically, we scrutinized how the distribution functions of the particles are manifested as the electrostatic field propagates, with a focus on three distinct particle ranges …

Restoration Of Strength In Polyamide Woven Glass Fiber Organosheets By Hot Pressing, Mohammad Nazmus Saquib, Edwing Chaparro-Chavez, Christopher Morris, Kuthan Çelebi, Diego Pedrazzoli, Mingfu Zhang, Sergii G. Kravchenko, Oleksandr G. Kravchenko

Mechanical & Aerospace Engineering Faculty Publications

Thermoplastic composite organosheets (OSs) are increasingly recognized as a viable solution for automotive and aerospace structures, offering a range of benefits including cost-effectiveness through high-rate production, lightweight design, impact resistance, formability, and recyclability. This study examines the impact response, post-impact strength evaluation, and hot-pressing repair effectiveness of woven glass fiber nylon composite OSs across varying impact energy levels. Experimental investigations involved subjecting composite specimens to impact at varying energy levels using a drop-tower test rig, followed by compression-after-impact (CAI) tests. The results underscore the exceptional damage tolerance and improved residual compressive strength of the OSs compared to traditional thermoset composites. …

Insights Into The Characterization And Degradation Of Electrospun Polycaprolactone Scaffolds For Tissue Engineering Applications, Caleb B. Wells

Theses and Dissertations

Electrospun polymeric biodegradable scaffolds are essential in tissue engineering, particularly for Engineered Tissue Vascular Grafts (ETVGs), which promise advancements in treating coronary artery disease, peripheral arterial disease, congenital cardiovascular defects, and renal disease. These scaffolds present a solution to issues with autologous graft availability and durability. While large-diameter grafts in low-pressure environments have seen success, small-diameter grafts in high-flow scenarios remain challenging. Understanding polymeric scaffold degradation and behavior during incubation, especially under dynamic mechanical loading, is vital for clinical translation of small-caliber ETVGs.

This research focuses on characterizing the mechanical and microstructural properties of electrospun polycaprolactone (PCL) scaffolds and their …

Kinetic Modeling Of Electrostatic Sieving For Lunar Regolith Beneficiation: Case Studies, Easton Ingram, Emmanuela Amen Eze, Jeffrey Smith, Fateme Rezaei, David Bayless, William Schonberg, Daoru Han

Materials Science and Engineering Faculty Research & Creative Works

A new kinetic particle modeling framework was developed to investigate electrostatic transport of lunar regolith particles with applications to the concept of electrostatic sieving. the new approach is based on kinetic particle dynamics and includes major modules of sampling the particle size distribution, solving electric fields, and tracking motion of charged dust grains. Case studies for a concept of electrostatic sieving were chosen to validate the new model. the simulation achieved similar yields reported in previous works, which served as validation of the model. the new model is computationally efficient and could serve as a design, analysis, and optimization tool.

Progress Of Lisap-Mse: A Concept Of Producing Aluminum In-Situ On The Moon Through Molten Salt Electrolysis, Jacob N. Ortega, David Bayless, Daniel Stutts, Daoru Han, Todd P. Sander, Jeffrey Smith, Fateme Rezaei, William Schonberg

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper presents a concept of producing aluminum in-situ on the lunar surface, namely, the Lunar In-Situ Aluminum Production through Molten Salt Electrolysis (LISAP-MSE) method developed at Missouri University of Science and Technology. This paper aims to demonstrate the use of electro-deoxidation to reduce aluminum oxide (i.e., alumina) into aluminum and oxygen gas via electrolysis in a molten salt bath for the production of aluminum on the Moon. It is shown that with a steady supply of hydrogen chloride, this in-situ resource utilization (ISRU) method could supply several necessary materials consumed in the electro-deoxidation process except hydrogen chloride to produce …

Dual Airfoil Testing System, Zifeng Yang, Collin Charvat, Jack Stafford, Kyle Mathews, Logan Kelly

Mechanical and Materials Engineering Faculty Publications

A dual airfoil testing system includes a platform including a frame defining a chamber that is configured to receive a horizontal flow of air for testing a first airfoil and a second airfoil contained in the chamber and a control system including a controller to control a first attack angle stepper motor, a second attack angle stepper motor, at least one gap stepper motor, and at least one stagger stepper motor. The controller is configured to automatically control and adjust the stepper motors to control and adjust the attack angle of the first airfoil, the attack angle of the second …

Fabrication Of Smooth Sac305 Thin Film Via Magnetron Sputtering, M. Ojha, A. A. Elmustafa

Mechanical & Aerospace Engineering Faculty Publications

SAC305 (96.5 wt% Sn, 3 wt% Ag, 0.5 wt%Cu) solder is increasingly becoming popular due to its reliability good characteristics and performance in addition to the environmental concerns and regulations that restrict the use of lead in nano/microelectronic products. In nano/microelectronics, manufacturing smooth solder coatings free of defects such as voids and cracks, which can compromise joint reliability is crucial. Magnetron sputtering offers a high degree of control over film thickness and composition, resulting in films with excellent uniformity and adhesion. Despite these advantages, fabricating continuous and robust SAC305 films using magnetron sputtering remains a difficult task with limited research …