Mechanical Engineering Commons^™

Assisted Development Of Mesophase Pitch With Dispersed Graphene And Its Resulting Carbon Fibers, Aaron Owen

Theses and Dissertations--Mechanical and Aerospace Engineering

The efficacy of dispersed reduced graphene oxide (rGO) as a nucleation site for the growth of mesophase in an isotropic pitch was investigated and quantified in this study. Concentrations of rGO were systematically tested in an isotropic petroleum and coal-tar pitch during thermal treatments and compared to pitch without rGO. The mesophase content of each thermally treated pitch was quantified by polarized light point counting. Further characterization of softening temperature and insolubles were quantified. Additionally, the pitches with and without rGO were melt spun, graphitized, and tensile tested to determine the effects of rGO on graphitized fiber mechanical properties and …

Design And Analysis Of A 3d-Printed, Thermoplastic Elastomer (Tpe) Spring Element For Use In Corrective Hand Orthotics, Kevin Thomas Richardson

Theses and Dissertations--Mechanical and Aerospace Engineering

This thesis proposes an algorithm that determine the geometry of 3D-printed, custom-designed spring element bands made of thermoplastic elastomer (TPE) for use in a wearable orthotic device to aid in the physical therapy of a human hand exhibiting spasticity after stroke. Each finger of the hand is modeled as a mechanical system consisting of a triple-rod pendulum with nonlinear stiffness at each joint and forces applied at the attachment point of each flexor muscle. The system is assumed quasi-static, which leads to a torque balance between the flexor tendons in the hand, joint stiffness and the design force applied to …

Designed Extrudate For Ceramic Additive Manufacturing, Devin Mcmillen

Masters Theses

"The objective of this thesis work was to design ceramic paste systems that assist in achieving a high theoretical density ( > 95%) after deposition by a novel additive manufacturing process, i.e. Ceramic On-Demand Extrusion (CODE). The work is encompassed in five main sections: Sections 1 and 2 provide an introduction and literature review of relevant topics for the following sections of experimentation. Section 3 provides an analysis of a reaction chemistry to identify three discrete materials that could be combined via CODE and result in zirconium diboride (ZrB₂) post-sintering. Section 4 describes the development of a high solids …

Tungsten Doping Induced Superior Mechanical Properties Of Hafnium Oxide For Energy Applications, Ann Marie Uribe

Open Access Theses & Dissertations

Hafnium oxide, or hafnia, is a high temperature refractory material with good electrical, chemical, optical, and thermodynamic properties. The effects of dopants have been widely studied, especially after the discovery of ferroelectricity induced in hafnia thin films. While attractive and used in the opto-electronic, memory devices, and semiconductor industries, there is a lack in the literature on enhancing the mechanical properties of hafnium oxide, specifically through doping it with tungsten, another material of interest particularly for future high temperature device applications. Thus, this work aimed to grow hafnia thin films doped with varying amounts of tungsten. The samples were grown …

Titanium Incorporated Gallium Oxide (Ga-Ti-O): Structure Property Relationship And Performance Evaluation For Extreme Environment Applications, Sandeep Manandhar

Open Access Theses & Dissertations

The existing power generation systems, which utilize fossil fuels, are in dire need of efficient, reliable chemical sensors that can operate safely at higher temperatures. These sensors control the combustion environment and the emissions during combustion. Several sensing materials such as SnO2, ZnO, TiO2, WO3, and Ga2O3 exhibit high sensitivity to certain type of chemical molecules and in a certain range of temperatures. Among these candidate materials, β-Ga2O3 is stable at very high temperatures and has shown functionality for oxygen sensing at higher temperatures (>700°C). However, the response time and sensitivity must be significantly improved in order to derive …

Design Of Shape-Conforming Nosecone For Optimal Fluid Flow From Transonic To Supersonic Range, Anna Tombazzi

Williams Honors College, Honors Research Projects

Modern flight vehicles, such as rockets, missiles, and airplanes, experience a force caused by forebody wave drag during the flight. This drag force is induced when the frontal point of each vehicle breaks the pressure wave during flight. Efforts to reduce this wave drag force to improve flight efficiency include modifying the nosecone profile of the flight vehicles to lower the drag force.

This project revolved around creating a design to make the transformation of nosecone shapes from a ¾ Parabolic profile to a ½ Power Series profile possible, mid-flight. Using a novel nosecone assembly, shape memory alloys (SMAs) and …

Galvanic And Pitting Corrosion Of A Fastener Assembly, Julie Shallman

Williams Honors College, Honors Research Projects

This research focuses on coupled galvanic/pitting corrosion of AA7075 when combined with stainless steel in a fastener assembly. A one-dimensional mathematical model of a well-mixed thin film electrolyte is developed to predict the damage profile of the AA7075 surface when its protective coating is damaged. The damage exposes the galvanic couple. A time dependent system of partial differential equations for potential, chloride concentration, aluminum ion concentration, and damage is developed and solved numerically. Two approaches to calculate the current density within aluminum pits are discussed. The first is a current balance between the cathodic, anodic and passive portions of the …

The Nakahara Effect And Its Influence On Solution-Based 3d Printed Films, Daryl Kwakye-Ackah

Graduate Theses, Dissertations, and Problem Reports (ETD)

Motivated by the Nakahara Effect, the influence of altering printing parameters on fragmentation mechanism(s) of directly written titanium dioxide(TiO₂) films is investigated. The Nakahara effect states that a long lasting memory can be introduced into a colloidal system prior to drying, affecting the type of crack pattern formed due to externally applied forces. TiO₂ has important applications due to its interesting semiconducting properties, tunable band gap, photocatalytic properties, biocompatibility, and relative abundance. This is the reason it is used in this project as a model printing ink system.

In this research, two deposition methods (i.e. direct-ink writing …

High Temperature Polymer Composites Using Out-Of-Autoclave Processing, Sudharshan Anandan

Doctoral Dissertations

"High performance polymer composites possess high strength-to-weight ratio, corrosion resistance, and have design flexibility. Carbon/epoxy composites are commonly used aerospace materials. Bismaleimide based composites are used as a replacement for epoxy systems at higher service temperatures. Aerospace composites are usually manufactured, under high pressure, in an autoclave which requires high capital investments and operating costs. In contrast, out-of-autoclave manufacturing, specifically vacuum-bag-only prepreg process, is capable of producing low cost and high performance composites. In the current study, out-of-autoclave processing of high temperature carbon/bismaleimide composites was evaluated. The cure and process parameters were optimized. The properties of out-of-autoclave cured laminates compared …

Quantitative Phase-Field Modeling Of Crack Propagation In Multi-Phase Materials, Arezoo Emdadi

Doctoral Dissertations

”Research presented in this dissertation is focused on developing and validating a computational framework for study of crack propagation in polycrystalline composite ceramics capable of designing micro-architectures of phases to improve fracture toughness and damage tolerance of ZrB₂-based ultra-high temperature ceramics (UHTCs). A quantitative phase-field model based on the regularized formulation of Griffith’s theory is presented for crack propagation in homogenous and heterogeneous brittle materials. This model utilizes correction parameters in the total free energy functional and mechanical equilibrium equation within the crack diffusive area to ensure that the maximum stress in front of the crack tip is …

Direct Printing Of Single-Crystal Silicon By Microscale Nanoparticle Printing And Confined Laser Melting And Crystallization, Wan Shou

Doctoral Dissertations

"The transport and interfacial phenomena in laser melting and crystallization of silicon in micro-/nano-scale confinement lacks sufficient understanding. Uncovering the underlying mechanisms, and hence harness the melting and crystallization processes can help the formation of controllable single-crystal structures or patterns. In this dissertation, a molecular dynamics (MD) simulation was conducted to calculate the interfacial free energy of the silicon system in contact with flat and structured walls. Then the calculated interfacial energies were employed to predict the nucleation mechanisms in a slab of liquid silicon confined by two walls and compared with MD simulation results. Further, in combination with a …

Thermal-Fatigue And Thermo-Mechanical Equivalence For Transverse Cracking Evolution In Laminated Composites, Javier Cabrera Barbero

Graduate Theses, Dissertations, and Problem Reports (ETD)

Carbon fiber reinforced plastics (CFRP) are potential materials for many aerospace and aeronautical applications due to their high specif strength/weight and a low coeffcient of thermal expansion (CTE) resulting in a high long-term stability. Among candidate structures, the re-entry reusable launch vehicles (RLV), the fuel oxidant storage and transportation at cryogenic temperature, space satellites, and aircraft structure (frame, wings, etc...) can be highlighted. However, CFRP are prone to internal damage as a result of high residual stresses and thermal fatigue loading. In this study, micro-cracking damage evolution in laminated composites subjected to monotonic cooling and thermal cyclic loads is developed …

The Effect Of Friction Stir Processing On The Microstructure And Tensile Behavior Of Aluminum Alloys, Nelson Gomes Affonseca Netto

UNF Graduate Theses and Dissertations

Friction Stir Processing (FSP) is a promising thermomechanical technique that is used to modify the microstructure of metals locally, and thereby locally improve mechanical properties of the material. FSP uses a simple and inexpensive tool, and has been shown to eliminate pores and also reduce the sizes of intermetallics in aluminum alloys. This is of great interest for research on solidification, production and performance of aluminum alloy castings because FSP can enhance the structural quality of aluminum casting significantly by minimizing the effect of those structural defects.

In the literature, there is evidence that the effectiveness of FSP can change …

Hydrophobicity Of Low Temperature Vibrating Surfaces, Christian Fergusson

Theses and Dissertations

This study proposes a method to enhance the anti-icing capabilities of superhydrophobic surfaces by utilizing vibration to further reduce contact time of an impacting droplet in addition to keeping the droplet in the Cassie-Baxter regime, where surface adhesion is lower than the opposing Wenzel regime. We tested this with two methods: by investigating the effects of vibration normal to the plane of a superhydrophobic surface being impacted by water droplets in a room temperature environment, with the surface horizontal in a room temperature environment and tiled in a subzero degree environment. The amplitude and frequency of the vibration were varied …

Liquid Interaction With Non-Wettable Surfaces Structured With Macroscopic Ridges, Mehran Abolghasemibizaki

Theses and Dissertations

Self-cleaning, anti-corrosion, anti-icing, dropwise-condensation, and drag-reduction are some applications in which superhydrophobic surfaces are implemented. To date, all the studies associated with superhydrophobic surfaces have been dedicated to understanding the liquid interaction with surfaces that are macroscopically smooth. The current study investigates the solid-liquid interaction of such surfaces which are fully decorated with macroscopic ridges (ribbed surfaces). In particular, the drop motion and impact on our newly designed non-wettable ribbed surface have been investigated in this work. Our experimental investigations have shown that liquid drops move faster on the ribbed surfaces due to lower friction induced by such a surface …

Consuming Digital Debris In The Plasticene, Stephen R. Parks

Theses and Dissertations

Claims of customization and control by socio-technical industries are altering the role of consumer and producer. These narratives are often misleading attempts to engage consumers with new forms of technology. By addressing capitalist intent, material, and the reproduction limits of 3-D printed objects’, I observe the aspirational promise of becoming a producer of my own belongings through new networks of production. I am interested in gaining a better understanding of the data consumed that perpetuates hyper-consumptive tendencies for new technological apparatuses. My role as a designer focuses on the resolution of not only the surface of the object through 3-D …

The Microstructural Annealing Response Of Cold Gas Dynamically Sprayed Al 6061, Clayton Andrew Cushway

UNF Graduate Theses and Dissertations

The Cold-Gas Dynamic-Spray process also known as Cold Spray (CS) has been researched for three decades. The CS process is a solid-state deposition technique via supersonic velocity of powder particles at a temperature significantly below the melting point of the spray material. This thesis presents background on the overall CS process parameters, and additional information on the microstructural and mechanical properties of typical Cold Sprayed materials.This Thesis primarily presents a study on the microstructural annealing response of CS Al 6061. It should be noted that for this study, the term “annealing” is used in the sense of the classical metallurgical …

A Scientific Approach To Understanding The Head Trauma Endured By A Mixed Martial Arts Fighter, John William Michael Sorbello

Mechanical & Aerospace Engineering Theses & Dissertations

The purpose of this research is to gain some insight on the type of head trauma an athlete may encounter during mixed martial arts (MMA) competition. These athletes endure continuous blows to the head throughout their training and fighting career. The knowledge obtained from this research may assist MMA athletes and trainers in assessing the way they train, how they compete and, more importantly, how long they choose to compete in their amateur or professional MMA career.

The analysis is performed by first creating a three-dimensional solid model of the human head based on geometric coordinates originally obtained from a …

Design, Manufacture, And Structural Dynamic Analysis Of A Biomimetic Insect-Sized Wing For Micro Air Vehicles, Jose Enrique Rubio

LSU New Orleans Theses and Dissertations

The exceptional flying characteristics of airborne insects motivates the design of biomimetic wing structures that can exhibit a similar structural dynamic behavior. For this purpose, this investigation describes a method for both manufacturing a biomimetic insect-sized wing using the photolithography technique and analyzing its structural dynamic response. The geometry of a crane fly forewing (family Tipulidae) is acquired using a micro-computed tomography scanner. A computer-aided design model is generated from the measurements of the reconstructed scanned model of the insect wing to design the photomasks of the membrane and the venation network required for the photolithography procedure. A composite …

Investigation Of 2195 And 2219 Post Weld Heat Treatments For Additive Friction Stir Lap Welds, Matthew Champagne

LSU New Orleans Theses and Dissertations

To evaluate potential uses for friction stir welding in additive manufacturing, two separate parts were fabricated, one of 2195-T84 and the other 2219-T87, utilizing fixed pin techniques and additive lap welds. The parts were cut into samples, artificially aged and subjected to Rockwell hardness (HRB), Vickers hardness, micrographic photography, and metallographic imaging on both pre- and post- heat treatment. Additionally, tensile testing was performed on the heat-treated samples. A comparisons of test results showed a minimal increase in the yield strength of the 2195-T84 samples compared to as-welded tensile results obtained from a previous project. The ultimate tensile strength was …

The Inter-Laminar Shearing Effect On Wrinkle Development In Composite Forming Processes, David Sundquist

McKelvey School of Engineering Graduate Student Theses & Dissertations

Composite materials are becoming prevalent in aerospace industries as the uniqueness of the composite structure allows the composite to be tailored specifically for individual applications. Many fabrication techniques produce defects in composite parts such as wrinkles, fiber waviness, fiber misalignment, and porosity. The driving mechanisms behind these defects occurring during forming processes are not fully understood and, thus, characterization formation of these defects in a uncured state is beneficial to optimize composite processing. This work primarily investigated the influence of how uncured pre-impregnated carbon ply properties affect the wrinkling behavior of a composite laminates. Several factors affecting composite ply forming …

Heterogeneous Anisotropy Index And Scaling In Multiphase Random Polycrystals, Muhammad Ridwan Murshed

Theses and Dissertations

Under consideration is the finite-size scaling of elastic properties in single and two-phase random polycrystals with individual grains belonging to any crystal class (from cubic to triclinic). These polycrystals are generated by Voronoi tessellations with varying grain sizes and volume fractions. By employing variational principles in elasticity, we introduce the notion of a 'Heterogeneous Anisotropy Index' and investigate its role in the scaling of elastic properties at finite mesoscales. The index turns out to be a function of 43 variables, 21 independent components for each phase and the volume fraction of either phase. Furthermore, the relationship between Heterogeneous Anisotropy Index …

Energy Potentials Of Briquette Produced From Tannery Solid Waste, Olatunde Ajani Oyelaran, Faralu Muhammed Sani, Olawale Monsur Sanusi, Olusegun Balogun, Adeyinka Okeowo Fagbemigun

Makara Journal of Technology

The vast quantity of waste generated from industries is one of the serious outcomes of unplanned development, resulting into quantum of hazardous organic and inorganic waste generating daily. Proper waste management is a challenging issue that must be addressed adequately. This is, therefore, carried out with a view of assessing the energy and combustion quality of tannery solid waste with a view of converting them into briquettes for cooking, heating and small home industries and reducing the menace caused by tannery waste disposal. The results of the experiments showed that the combustion rate ranged between 0.171 and 0.217 g/min, the …

Adsorption Of Cu(Ii) Ions In Aqueous Solution Onto Limonia Acidissima Shellbased Activated Carbon: Kinetic And Isotherm Studies, Abrar Muslim, Syahiddin Dahlan Said, Gita Suci Hariati, Siti Fajar Karina, Fauzi Muhammad Djuned, Rizka Mulyawan

Makara Journal of Technology

Adsorption of Cu(II) ions from aqueous solution using activated carbon prepared from Limonia acidissima fruit shell (LAFS-AC) was conducted in batch mode experiments at pH 5 (±0.15), 100 rpm and 1 atm. The effects of contact time, initial Cu(II) ions concentration, KOH concentration, and adsorption temperature on Cu(II) ions adsorption capacity were investigated. Fourier Transform Infrared Spectroscopy and Scanning Electron Microscopy analyses were performed to investigate the active site and surface morphology of the LAFS-AC, respectively. The Cu(II) ions adsorption was fitted very well (R2 = 0.94 on average) to the pseudo second-order adsorption kinetic with the adsorption capacity and …

Experimental Study On Automatic Control For Collision Avoidance Of Ships, Daeng Paroka, Muhammad Fahmi Kamil, Andi Haris Muhammad

Makara Journal of Technology

Automatic control system is widely applied to control the ship direction or heading angle in accordance with the decided trajectory. Several methods for improving performance of control system have been developed such as Proportional-Integral-Derivative (PID) control and fuzzy logic based control. Within the last decade, application of automatic control system is not only for ship navigation but also for avoiding collision risk of ships in seaways. This paper discusses the application of automatic control system for avoiding ship collision by free running experiment. Fuzzy logic based control was developed using Mamdani Centroid method to estimate the necessary rudder angle in …

Indonesia’S Municipal Solid Waste 3r And Waste To Energy Programs, Farizal Farizal, Radityo Aji, Amar Rachman, Nasruddin Nasruddin, Teuku Meurah Indra Mahlia

Makara Journal of Technology

Like most cities in the world, population in Indonesia continues to grow every year. Problems that can arise from this are the increasing amount of municipal solid waste (MSW) production and the growing demand for electricity. To deal with the problems, Indonesian government runs 3R (Reduce, Reuse and Recycle) and WTE (Waste to Energy) Programs simultaneously. 3R program aims to reduce the number of waste, while WTE program aims to generate electricity as an alternative energy source. This study aims to find out the optimal proportion of MSW treated through the 3R and WTE programs. For the purpose, a goal …

Study On Semiconductor Properties Of Acetylide-Thiourea Fabricated Onto Interdigitated Electrodes (Ides) Platform Towards Application In Gas Sensing Technology, Adibah Izzati Daud, Wan M. Khairul, M. I. N. Isa, Khairul Anuar Abdul Wahid

Makara Journal of Technology

In the past few decades, the unique properties of acetylide and thiourea moieties individually have attracted great attention from researchers in various fields to be developed in numerous applications in advanced materials technology, especially as an active layer in gas sensing devices. The molecular systems of acetylide and thiourea provide a wide range of electronic properties as they possess rigid π-systems in their designated structures. In this study, a derivative of acetylide-thiourea featuring N-(4[4-aminophenyl] ethynyl benzonitrile)-N’-(4-ethyl benzoyl) thiourea (TCN) has been synthesised with the general formula of ArC(O)NHC(S)NHC≡C)Ar adopted the system of D-π-A for the significant development of conductive materials. …

Experimental Study Of The Chimney Height Variation Against Double Pots Biomass Stove Performance, Faisal Faisal, Adi Setiawan, Wusnah Wusnah, Khairil Khairil, Luthfi Luthfi, Mona Fajriana

Makara Journal of Technology

This research aims to get optimal chimneys height of double pots biomass stove. Optimal chimneys height needs to provide best performance of the stove. Experimental study was done by varied the chimney heights. Water boiling test as the standard method was used to obtained stove performance for each chimney height variation. The results showed that best performance stove was the one with 1.65 cm chimney height, with thermal efficiency at 37.66%.

Assessment On Heck-Immine Derivatives As Organic Semiconductor Materials, Rafizah Rahamathullah, Lim Keemi, Wan M. Khairul

Makara Journal of Technology

This paper reports the synthetic, characterization and theoretical evaluation of new class of hybrid Heck-immine system involving mixed moieties of vinylene (C=C) and azomethines (CH=N) which has been successfully integrated into an addition of organic semiconducting materials. The assessment of 4-[(hexyloxyphenyl)methylene]amino)-4’-chloro-stilbene (HEXCS) based on Donor (D)-π-Acceptor (A) was evaluated as active semiconductor material candidates via several spectroscopic and analytical techniques. In turn, the investigation of its potential as dopant system in conductive film was successfully deposited on indium tin oxide (ITO) coated substrate via spin coating method. The relationship between electronic and optical properties, chemical modelling at molecular interactions and …

Innovation Of Hydrocarbon Investigation Using Audio-Magnetotelluric In Cepu Field, Indonesia, Iqbal Fauzi Aditama, Widodo Widodo

Makara Journal of Technology

An audio-magnetotelluric (AMT) survey has been performed at Cepu oil field located in Indonesia. The objective of this research is to detect resistivity structures of this important hydrocarbon rock. This research can be classified as an innovation in application of the AMT method for hydrocarbon exploration. The lack of seismic resolution has been provided by the AMT method, especially in the location of sub-basalt and sub-salt plays. In additional, the cost of AMT survey is quite low compared to seismic. The forward modelling is included in this research to understand the measurement data response from a mathematical model. In the …