Mechanical Engineering Commons^™

Development Of Synthetic Coal Char Simulant For Microwave Conversion Studies: A Computationally-Driven Approach, Kevin A. Hager

Graduate Theses, Dissertations, and Problem Reports (ETD)

Recent experimental demonstration of new reaction windows for coal char/methane reactions that are less energy-intensive, provides innovation for modular reactors. However, the correlation of the exact mechanism for the enhancement of these reaction windows is not certain. This study investigates the simplification of these experimental studies by developing a well-characterized coal char simulant. The approach involves using a computational approach to screen macroscopic composition to replicate the dielectric and compositional response of actual char. This study is focused on PRB coal char. A discrete element method (DEM) technique was used to simulate the packing of coal chars to give the …

Dry Reforming Of Methane Using Microwave Irradiated Metal Oxide/Coal Char Catalysts, Anthony Carter

Graduate Theses, Dissertations, and Problem Reports (ETD)

This research focuses on the synthesis of both shaped and amorphous powder materials, the combination of these materials with dried Powder River Basin (PRB) coal char, and their reactionary properties with methane and carbon dioxide gasses with conventional and microwave (MW) heating. The first goal of this project was to synthesize shaped micro and nano sized particles with ideal dielectric properties for converting electromagnetic energy into heat and proven capabilities of activating methane. These particles were synthesized via solvothermal, hydrothermal, and co-preceptory treatments alone and onto the surface of dried PRB coal char. PRB is a sub-bituminous, low-ranking coal (LRC) …

Studying The Effects Of Initial Crack Angle On The Crack Propagation In Graphene Nano-Ribbon Through Molecular Dynamics Simulations, Vijay Kumar Pathak

Dissertations, Master's Theses and Master's Reports

In this research, we have worked on the brittle fracture of graphene nano-ribbon to explore the behavior of crack propagation at different crack angles. We have performed classical Molecular Dynamics simulations using LAMMPS at ten different crack angles between 0 degrees and 45 degrees, in an increment of 5 degrees to observe the parameters that dominate the crack path. The graphene nanoribbon is loaded in the zigzag direction by pulling it in the armchair direction with a pre-existing crack in the center. We have used OVITO for the visualization of the simulation. AIREBO potential is employed in this work because …

Thermomechanical Mechanisms That Cause Adhesion Of Aluminum High Pressure Die Castings To The Die, Alex Monroe

Dissertations, Master's Theses and Master's Reports

In high pressure die casting (HPDC) of aluminum, cast material adhering to die is a significant defect. Adhesion occurs in two primary ways. The casting may stick preventing its removal from the die. Aluminum can also adhere to the die and buildup in local areas on the die surface with additional casting cycles. This second form of adhesion is called soldering. Lubricant is the best technology to control all forms of adhesion, but it comes at the cost of casting porosity, blisters, reduced die life, and increased die casting machine wear. New strategies to prevent adhesion are desired to eliminate …

Experiments And Modeling Of The Chemo-Mechanically Coupled Behavior Of Polymeric Gels, Nikola Bosnjak

Dissertations

Polymeric materials consist of mutually entangled or chemically crosslinked long njitmolecular chains which form a polymer network. Due to their molecular structure, the njitpolymeric materials are known to undergo large deformation in response to various njitenvironmental stimuli, such as temperature, chemical potential and light.

When a polymer network is exposed to a suitable chemical solvent, the solvent molecules are able to diffuse inside the network, causing it to undergo a large volumetric deformation, known as swelling. In addition to volumetric deformation, this process involves the chemical mixing of the polymer network and solvent molecules, and is typically environmentally responsive. A …

Cooling Under Applied Stress Rejuvenates Amorphous Alloys And Enhances Their Ductility, Nikolai Priezjev

Mechanical and Materials Engineering Faculty Publications

The effect of tensile stress applied during cooling of binary glasses on the potential energy states and mechanical properties is investigated using molecular dynamics simulations. We study the three-dimensional binary mixture that was first annealed near the glass transition temperature and then rapidly cooled under tension into the glass phase. It is found that at larger values of applied stress, the liquid glass former freezes under higher strain and its potential energy is enhanced. For a fixed cooling rate, the maximum tensile stress that can be applied during cooling is reduced upon increasing initial temperature above the glass transition point. …

Detection Of Nucleotides In Hydrated Ssdna Via 2-D H-Bn Nanopore With Ionic-Liquid/Salt-Water Interface, Jungsoo Lee

Multidisciplinary Studies Theses and Dissertations

Accomplishing slow translocation speed with high sensitivity has been the greatest mission for solid-state nanopore (SSN) to electrically detect nucleobases in single-stranded DNA (ssDNA). In this study, a method to detect nucleobases in ssDNA using a SSN is introduced by considerably slowing down the translocation speed and effectively increasing its sensitivity. The ultra-thin titanium dioxide (TiO₂) coated hexagonal boron nitride (h-BN) nanopore was fabricated, along with an ionic-liquid [bmim][PF₆]/2.0 M KCl aqueous (cis/trans) interfacial system, to increase both the spatial and the temporal resolutions. As the ssDNA molecules entered the nanopore, a …

Thermo-Fluid Characterizations Of The Powder-Bed Fusion Additive Manufacturing Processes Using Laser And Electron Beam, M Shafiqur Rahman

LSU New Orleans Theses and Dissertations

The powder-bed fusion (PBF) process is a subdivision of Additive Manufacturing (AM) technology where a heat source at a controlled speed selectively fuses regions of a powder-bed material to form three-dimensional (3-D) parts. Two of the most effective PBF processes are selective laser melting (SLM) and electron beam additive manufacturing (EBAM), which can fabricate full-density metallic parts in a layer-by-layer fashion. In this study, thermal behavior and melt-pool dynamics in the PBF process are investigated by developing 3-D multiphysics-based thermo-fluid models for both SLM and EBAM, containing Ti-6Al-4V alloy as a powder-bed material. The laser and electron beams are modeled …

Interface Engineering Of Materials For Energy And Biological Applications, Ardalan Chaichi

LSU Doctoral Dissertations

Interface interactions are generally classified into solid-liquid, solid-gas, solid-vacuum, liquid-gas, light-matter and electron-matter categories. Surface morphological studies as well as surface chemical reactions can be studied in various types of complex systems thanks to technological advances in materials characterization methods. By employing interface engineering in different applications, it is possible to control electrical, chemical, mechanical, optical and biological properties of materials. Accordingly, we have applied interface engineering in three different areas of energy materials, biomaterials and surface imaging. As a result, firstly, we have introduced a high intensity light flash-based method on engineered substrates for delamination of reduced graphene oxide …

Numerical Evaluation Of Effective Thermal Response Of Heterogeneous Materials, Kevin W. Irick

Mechanical Engineering ETDs

Heterogeneity in materials leads to increased complication of physics, at the level or scale where heterogeneity exists, making analysis and material behavior predictions more difficult. As a result of the intricate descriptions or understanding of the physics required to determine the behavior of a heterogenous material or system, practitioners frequently prefer the use of effective properties or responses. This body of work is dedicated to performing computational analyses on the thermal behavior of heterogeneous materials and evaluating the corresponding analyses using formal verification approaches. Custom finite element method code was used for solving the heat equation in a variety of …

Influence Of The Shaping Process On The Tensile Properties Of Steel Reinforcement Bars Carbon Steel Grades Bjtp24 And Bjts40, Nuraziz Handika, Ridha Amalia Idhar, Jessica Sjah, Essy Arijoeni, Elly Tjahjono

Makara Journal of Technology

According to the current applicable national standard in Indonesia, i.e. SNI 07 2529 1991, in addition to the limitation on the loading rate, the steel bar must be reduced, formed, or lathed, as part of the shaping process of samples. This study determined and compared the effect of the shaping process on the yield strength, ultimate strength, and percent elongation by conducting tensile tests of steel bar grade BJTS40, i.e. deformed bar type of steel, and grade BJTP24, i.e., plain bar type of steel. Three diameters of the deformed bar (BJTS40) and one diameter of the plain bar (BJTP24) were …

A Density Functional Theory Study On Using Montmorillonite To Reduce Air Pollution, Triati Dewi Kencana Wungu, Meqorry Yusfi, Suprijadi Suprijadi

Makara Journal of Technology

In this study, density functional theory (DFT) method is used to investigate the possibility of using a smectite clay mineral called montmorillonite (MMT) in reducing heavy metals, such as Cd, through Cd adsorption. The mechanism of Cd adsorption in MMT is observed theoretically, and the tetrahedrally isomorphic substitution on the upper layer of MMT is considered to observe the role of Al and Fe in strengthening Cd adsorption. Two types of MMT are modeled in this study: Al-MMT and Fe-MMT. The Al-MMT means that Al substitutes one atom in the upper tetrahedral layer of MMT, while Fe-MMT means that Fe …

Ionic Conductiviy Of Alginate-Nh4cl Polymer Electrolyte, Nurhasniza Mamajan Khan, Noor Saadiah Mohd Ali, Ahmad Faizrin Ahmad Fuzlin, Ahmad Salihin Samsudin

Makara Journal of Technology

This study aims to produce a solid biopolymer electrolyte (SBE) by doping ammonium chloride (NH4Cl) into alginate. Solution casting was used to prepare the alginate–NH4Cl SBE system. Electrical impedance spectroscopy was performed to analyze the electrical properties of the SBE under the applied frequency range of 50 Hz–1 MHz. The incorporation of 8 wt.% NH4Cl enhances the ionic conductivity of the SBE up to 3.18 × 10-7 S/cm at ambient room temperature. Fourier transform infrared spectroscopy shows that complexation occurs between the hydroxyl (-OH), carboxylate (COO-) and ether linkage (C-O-C) functional groups due to the formation of inter- and intra-molecular …

Use Of Viscoplastic Damper For Improving The Resistance Of Steel Frames To Blast Loading, Gholamreza Abdollahzadeh, Hadi Faghihmaleki, Hamed Hamidi Jamnani, Atefeh Ebrahimi Bardar

Makara Journal of Technology

In this paper, we evaluated the effect of viscoplastic dampers on the response of steel frames under blast loading. We used SAP2000 software and link elements to investigate the responses of nine-story steel frames with and without dampers. The proposed viscoplastic damper is a new type of viscous damper. The application of this damper is based on the availability of its constituent materials. The damper acts as a viscoelastic damper at low levels of vibration, but it acts as a combination of viscoelastic operator and metal-yielding device at extreme levels of vibration. With respect to the height of the structure, …

Influence Of Lithium Bromide On Electrical Properties In Bio-Based Polymer Electrolytes, Ahmad Faizrin Fuzlin, Bouchta Sahraoui, Ahmad Salihin Samsudin

Makara Journal of Technology

This research presents the influence of lithium bromide (LiBr) on the electrical properties of alginate in bio-based polymer electrolytes (BBPEs) system. Bio-based alginate was prepared using the solution casting technique with various LiBr compositions. The ionic conductivity and electrical properties of the prepared BBPEs samples were studied using electrical impedance spectroscopy over a frequency range of 50 Hz–1 MHz. A maximum ionic conductivity of 7.46 × 10−5 S cm-1 was obtained for a sample containing 15 wt. % lithium bromide-doped alginate BBPEs at ambient temperature (303 K). The electrical analysis revealed that the most conductive sample based on alginate-LiBr BBPEs …

Mechanical Alloying-Assisted Coating Of Fe–Al Powders On Steel Substrate, Alfian Noviyanto, Sri Harjanto, Wahyu Bambang Widayatno, Agus Sukarto Wismogroho, Muhamad Ikhlasul Amal, Nurul Taufiqu Rochman

Makara Journal of Technology

The coating layer of Fe–Al powders on the steel substrate was prepared by mechanical alloying at room temperature. Fe, Al, and the steel substrates were milled with high-energy ball milling for 32 h with a ball-to-powder ratio of 8 in an argon atmosphere to prevent oxidation during milling. Although mechanical alloying was performed for 32 h, no new phases were observed after mechanical alloying, as analyzed by X-ray diffraction. However, the crystallite size of the milled powders for 32 h decreased by factor two compared with the initial powders. Scanning electron micrographs showed that the coating layers formed >8 h …

Performance Of Free-Space Optical Communication Systems Using Optical Amplifiers Under Amplify-Forward And Amplify-Received Configurations, Ucuk Darusalam, Arockia Bazil Raj, Fitri Yuli Zulkifli, Purnomo Sidi Priambodo, Eko Tjipto Rahardjo

Makara Journal of Technology

With the growth of digital technology in the stage of industrial revolution 4.0, the demand for broadcasting large amounts of information to last mile users has increased. Free-space optical (FSO) communication is one of the telecommunication platforms that has shown immense potential in meeting the demand for information broadcasting. In this work, the performance of FSO communication based on wavelength division multiplexing with a data rate of 80 Gbps is investigated through simulations. The configuration of optical amplifiers in the FSO system is set up on the basis of the amplify-forward and amplify-received configurations to expand the network. The investigation …

Iso 9001:2015 Risk-Based Thinking: A Framework Using Fuzzy-Support Vector Machine, Ralph Sherwin A. Corpuz

Makara Journal of Technology

Risk-based thinking (RBT) is one of the distinct new features of the International Organization for Standardization 9001:2015. Interestingly, the standard does not prescribe any tools. Hence, organizations are puzzled as to the extent of conformance. Some organizations have adopted formal tools. However, these tools seem insufficient in linking the standard into an evidence-based decision support system. To resolve gaps in RBT implementation, this paper proposes a framework based on fuzzy inference system (FIS) and support vector machine (SVM) to automate risk analysis and evaluation, proposal and verification of action plans, and prediction of the feasibility of risks and opportunities according …

Practical Adhesion Measurements In Organic Coatings; Advancing Understanding And Mechanical Methods Development, Diana Gottschalk

Dissertations

“Adhesion” can be considered either a mechanical or chemical phenomenon. The mechanical interpretation describes the difficulty of separating surfaces and is useful for quantifying performance within applications that depend on bulk and interfacial properties. Chemical adhesion describes interfacial resistance to chemical attack and does not depend on bulk properties. Predicting chemical failure through mechanical measurement is confounded by the influence of bulk properties. However, the prospect is attractive because of the robust tolerance for sample geometries, allowing experiments to resemble an end-use system. The present work's primary goal was to elevate mechanical methods to provide a detailed interfacial characterization of …

Adhesion And Deformation Mechanisms Of Polydopamine And Polytetrafluoroethylene: A Multiscale Computational Study, Matthew Brownell

Graduate Theses and Dissertations

Polydopamine (PDA) has been shown to bond via covalent bonding, van der Waals forces, and hydrogen bonding and is known to adhere strongly to almost any material. The application of PDA between a substrate and a PTFE surface coating has resulted in low friction and a greatly reduced wear rate. Previous research probing the capabilities and limitations of PDA/PTFE films have studied the wear and mechanical properties of the film, but the overall adhesive and deformation mechanisms remain unclear.

In this research, we investigate the tribological properties of PDA and PTFE molecules and composites from the atomic to the microscale …

Design, Fabrication, And Reliability Effects Of Additively Manufactured First Level Compliant Interconnects For Microelectronics Application, Tumininu David Olatunji

Graduate Theses and Dissertations

Semiconductor packaging and development is greatly dependent on the magnitude of interconnect and on-chip stress that ultimately limits the reliability of electronic components. Thermomechanical related strains occur because of the coefficient of thermal expansion mismatch from different conjoined materials being assembled to manufacture a device. To curb the effect of thermal expansion mismatch between conjoined parts, studies have been done in integrating compliant structures between dies, solder balls, and substrates. Initial studies have enabled the design and manufacturing of these structures using a photolithography approach which involves a high number of fabrication steps depending on the complexity of the structures …

Mechanical And Frictional Behavior Of Textured And Non-Textured Surfaces, Raghuram R. Santhapuram

Graduate Theses and Dissertations

Tribology is the study of surfaces where two objects are sliding against another. Significant energy is lost due to friction between the sliding surfaces. Therefore, developing or designing surfaces to minimize friction is critical for the durability and reliability of the mechanical components. Several researchers have identified that surface texturing at the nanoscale (nanotexture) would reduce the friction between the contacting surfaces. The nanotextured surfaces have several applications in microelectromechanical systems and nanoelectromechanical systems. This dissertation employs molecular dynamics simulations to investigate the frictional and mechanical response of nanotextured aluminum (Al) and Al/amorphous silicon (a-Si) composite surfaces.

This study determines …

Fluid Modeling And Analysis Of A Mash Tl-6 Vehicle Model, Elisa Vasquez

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The objective of this research project was to replicate the dynamic behavior of a truck-tank trailer combination vehicle using representative dimensions, properties, and inertias of the trailer/fluid ballast combination. A literature review was completed describing techniques for modeling fluids and fluid-container interactions using finite element analysis. Various fluid modeling techniques were identified, and parameters associated with those models were archived. Next, researchers utilized the tank geometry of the elliptical straight-frame 5949 trailer produced by LBT Inc. to generate a finite element mesh using finite element analysis preprocessors HyperMesh and LS PrePost. Material properties were taken from reference guides, research papers, …

Modeling And Analysis For Unit Cell Size, Material Anisotropy And Material Imperfection Effects Of Cellular Structures Fabricated By Powder Bed Fusion Additive Manufacturing., Yan Wu

Electronic Theses and Dissertations

Cellular structures are networks of interconnected struts or walls with porosities and are widely found in many natural load-bearing structures such as plants and bones. Cellular structures offer unique functional characteristics such as high stiffness to weight ratio, tailorable heat transfer coefficient, and enhanced mechanical energy absorption, which makes them highly attractive in various engineering disciplines such as biomedical implants, electrodes, heat exchangers, and lightweight structures. There exists an abundance of literatures that have investigated various mechanical properties of various cellular structures such as Poisson’s ratio, elastic modulus, ultimate strength, yield strength, and failure characteristics. Based on the classic cellular …

Toward Understanding Underlying Mechanisms Of Drag Reduction In Turbulent Flow Control, Alex Rogge

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The underlying mechanisms of three different flow-control strategies on drag reduction in a turbulent channel flow are investigated by direct numerical simulations. These strategies include the addition of a small concentration of long-chain polymers into a fluid, the incorporation of slip surfaces, and the application of an external body force. While it has been believed that such methods lead to a skin-friction reduction by controlling near-wall flow structures, the underlying mechanisms at play are still not as clear. In this study, a temporal analysis is employed to elucidate underlying drag-reduction mechanisms among these methods. The analysis is based on the …

Numerical Analysis Of A Roadway Piezoelectric Harvesting System, Abdul Rahman Badawi

Mechanical & Aerospace Engineering Theses & Dissertations

Highways, streets, bridges, and sidewalks with heavy traffic dissipate a considerable amount of waste mechanical energy every day. Piezoelectric energy harvesting devices are a very promising technology that can convert the waste mechanical energy to clean and renewable energy to enhance the sustainability of infrastructures. Research efforts in large-scale energy harvesting have led to the advancement of piezoelectric devices to the point that large-scale implementation is starting to become more feasible. The energy harvested by these devices can be used in many ways such as providing heating or cooling, melting ice, monitoring structural conditions in bridges and tunnels, and powering …

The Effect Of Compaction Temperature And Pressure On Mechanical Properties Of 3d Printed Short Glass Fiber Composites, Pushpashree Jain Ajith Kumar Jain

Mechanical & Aerospace Engineering Theses & Dissertations

Among many thermoplastics that are used in engineering, polyamide 6 (nylon 6) is an extremely versatile engineering thermoplastic. Nylon filled with glass fibers has higher mechanical strength and high wear resistance than general purpose nylon. 3D printed composites, based on fused filament modeling, typically suffer from poor bead-to-bead bonding and relatively high void content, limiting their mechanical properties

This thesis explores the effect of compaction pressure and temperature on improving the mechanical properties of 3D printed composites. Engineering moduli in the printing and transverse to printing direction, as well as ultimate strength were measured using the tensile testing with Digital …

Direct Solar Absorption Nanoparticle Doped Membranes For A Hybrid Membrane Distillation And Photovoltaic Cell, Alejandro Espejo Sanchez

Boise State University Theses and Dissertations

The growing demand for clean water supplies is driving the need for an innovative approach of water desalination. Developing a method for treating water with high salinities is possible with membrane distillation (MD). Additionally, MD is very attractive for pairing with solar energy due to the low temperature requirements. The integration of a membrane distillation system with a photovoltaic (PV) system will result in the co-production of electricity and clean water, thereby improving the economics of MD. Such a hybrid system will directly absorb thermal energy in the membrane for desalination while taking advantage of the spectrally selective nature of …

Large Displacement J-Integral Double Cantilever Beam (Dcb) Test Method For Mode I Fracture Toughness, Joshua Gunderson

Boise State University Theses and Dissertations

The J-integral is used to develop an alternative double cantilever beam (DCB) test method for the Mode I fracture toughness suitable for both small and large displacements. The current focus is the experimental determination of the Mode I interlaminar fracture toughness of composite materials, but the method is generally applicable to other similar tests and material systems, such as to the Mode I fracture toughness of adhesives. A series of five identical specimens are tested to compare the linear-elastic fracture mechanics method recommended by ASTM, which makes use of linear beam theory with root rotation, large displacement, and end …

The Effect Of Guide Vane Opening Variations And Total Blades On Cross Flow Turbine Performance Using Computational Fluid Dynamic, Muhamad Akbar Navis, Heru Suryanto, Putut Murdanto

Journal of Mechanical Engineering Science and Technology (JMEST)

Indonesia is an agrarian country that continuously produces water, so it has the potential to develop a hydroelectric power plant. Computational Fluid Dynamic (CFD) application could be used to be an economical, quick, and efficient approach to improve the engineering design and turbine performance. This research aimed to find the effect of guide vane opening variations and total blades on cross-flow turbine performance using CFD simulation. This research used experimental modelling method with ANSYS program for turbine design with 22, 24, and 26 turbine blades and guide vane opening variations of 12°, 16°, 20°, 24°, and 36°. The data were …