Mechanical Engineering Commons^™

Frequency Domain Measurements Of Melt Pool Recoil Pressure Using Modal Analysis And Prospects For In-Situ Non-Destructive Testing, Tristan Cullom, Nicholas Altese, Douglas A. Bristow, Robert G. Landers, Ben Brown, Troy Hartwig, David Soine, Aimee Allen, Andrew Barnard, Jason Blough, Kevin Johnson, Edward C. Kinzel

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Fielding Additively Manufactured (AM) parts requires evaluating both the part’s geometry and material state. This includes geometry that may be optically hidden. Both the geometry and material state affect the vibration response of the parts and modal analysis (identifying natural frequencies) has been shown to be effective for at least simple geometries using ex-situ methods (shaker table and impact hammer excitations). This paper investigates evaluation of the frequency response of metal parts inside the build chamber using the process laser to excite the parts during printing (Renishaw AM250). Vibrations in the part are measured with accelerometers connected to the build …

The Effect Of Cell Size And Surface Roughness On The Compressive Properties Of Abs Lattice Structures Fabricated By Fused Deposition Modeling, Leah Mason, Ming-Chuan Leu

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Researchers looking to improve the surface roughness of acrylonitrile butadiene styrene (ABS) parts fabricated by fused deposition modeling (FDM) have determined that acetone smoothing not only achieves improved surface roughness but increases compressive strength as well. However, the sensitivity of ABS parts to acetone smoothing has not been explored. In this study we investigated FDM-fabricated ABS lattice structures of various cell sizes subjected to cold acetone vapor smoothing to determine the combined effect of cell size and acetone smoothing on the compressive properties of the lattice structures. The acetone-smoothed specimens performed better than the as-built specimens in both compression modulus …

Application Of Schlieren Technique In Additive Manufacturing: A Review, R. Bharadwaja, Aravind Murugan, Yitao Chen, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Additive manufacturing has gained a lot of attention in the past few decades due to its significant advantages in terms of design freedom, lower lead time, and ability to produce complex shapes. One of the pivotal factors affecting the process stability and hence the part quality is the shielding gas flow in additive manufacturing. As extremely beneficial for the process, the shielding gas flow is often set at maximum supply to achieve enough gas cover over the substrate. This causes excessive quantity of shielding gas to be unutilized. Realizing the importance of shielding gas, various studies have been carried out …

Applications Of Supervised Machine Learning Algorithms In Additive Manufacturing: A Review, M. S. Joshi, Aaron Flood, Todd E. Sparks, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Additive Manufacturing (AM) simplifies the fabrication of complex geometries. Its scope has rapidly expanded from the fabrication of pre-production visualization models to the manufacturing of end use parts driving the need for better part quality assurance in the additively manufactured parts. Machine learning (ML) is one of the promising techniques that can be used to achieve this goal. Current research in this field includes the use of supervised and unsupervised ML algorithms for quality control and prediction of mechanical properties of AM parts. This paper explores the applications of supervised learning algorithms - Support Vector Machines and Random Forests. Support …

Part Remanufacturing Using Hybrid Manufacturing Processes, Xinchang Zhang, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Many users of high-performance metal parts, such as the aerospace industry, the mold/die casting industry, and heavy machinery consumers, extend the service of these damaged parts by employing remanufacturing technology. Additive manufacturing has unique capabilities, such as low heat input, a small heat-affected zone, free-form fabrication, and a near-net-shape. This paper summarizes the effort and the tested results to achieve an automated remanufacturing process using hybrid additive manufacturing and CNC machining processes. It will enable the robust remanufacturing-on-demand to significantly increase operational availability to reduce sustainment costs, thus will lead to robust and quality remanufacturing that is critical for remanufacturing …

Wetting Metamorphosis Of Hydrophobic Fluoropolymer Coatings Submerged In Water And Ultrasonically Vibrated, Matthew Trapuzzano, Nathan B. Crane, Rasim Guldiken, Andrés Tejada-Martínez

Faculty Publications

Many important processes, from manufacture of integrated circuit boards, to an insect’s ability to walk on water, depend on the wetting of liquids on surfaces. Wetting is commonly controlled through material selection, coatings, and/or surface texture. However, wetting is sensitive to environmental conditions. In particular, some hydrophobic fluoropolymer coatings are sensitive to extended water exposure as evidenced by a declining contact angle and increasing contact angle hysteresis. Understanding “degradation” of these coatings is critical to applications that employ them. The durability of a series of fluoropolymer coatings were tested by measuring the contact angle before, during, and after extended submersion …

Development Of Smart Semiconductor Manufacturing: Operations Research And Data Science Perspectives, Marzieh Khakifirooz, Mahdi Fathi, Kan Wu

BCoE Publications

With advances in information and telecommunication technologies and data-enabled decision making, smart manufacturing can be an essential component of sustainable development. In the era of the smart world, semiconductor industry is one of the few global industries that are in a growth mode to smartness, due to worldwide demand. The important opportunities that can boost the cost reduction of productivity and improve quality in wafer fabrication are based on the simulations of actual environment in Cyber-Physical Space and integrate them with decentralized decision-making systems. However, this integration faced the industry with novel unique challenges. The stream of the data from …

Development Of Experimental And Finite Element Models To Show Size Effects In The Forming Of Thin Sheet Metals, Jeffrey D. Morris

LSU New Orleans Theses and Dissertations

Abstract

An experimental method was developed that demonstrated the size effects in forming thin sheet metals, and a finite element model was developed to predict the effects demonstrated by the experiment. A universal testing machine (UTM) was used to form aluminum and copper of varying thicknesses (less than 1mm) into a hemispherical dome. A stereolithography additive manufacturing technology was used to fabricate the punch and die from a UV curing resin. There was agreement between the experimental and numerical models. The results showed that geometric size effects were significant for both materials, and these effects increased as the thickness of …

Parametric Study Of Selective Laser Alloying Of Elemental Titanium And Boron Powders Using An Automated Deposition Mechanism, Julian V. Gonzalez

Theses and Dissertations

An automatic powder deposition and leveling mechanism was designed and constructed to assist in surface roughness experiments for titanium-boron samples. Previously developed energy models and x-ray diffraction analysis was used to confirm the creation of titanium diboride samples. To study TiB2 at different energy values, a 52 (2 factors, 5 levels) factorial design was used and carried out under an argon atmosphere, through the AM250 laser melting system. Two experimental runs were carried out and a total of 50 samples were assigned a surface roughness measurement through the Dektak XT profilometer. Graphically and with statistical analysis, the data was determined …

A Displacement Controlled Fatigue Test Method For Additively Manufactured Materials, Mohammad Masud Parvez, Yitao Chen, Sreekar Karnati, Connor Coward, Joseph William Newkirk, Frank W. Liou

Materials Science and Engineering Faculty Research & Creative Works

A novel adaptive displacement-controlled test setup was developed for fatigue testing on mini specimens. In property characterization of additive manufacturing materials, mini specimens are preferred due to the specimen preparation, and manufacturing cost but mini specimens demonstrate higher fatigue strength than standard specimens due to the lower probability of material defects resulting in fatigue. In this study, a dual gauge section Krouse type mini specimen was designed to conduct fatigue tests on additively manufactured materials. The large surface area of the specimen with a constant stress distribution and increased control volume as the gauge section may capture all different types …

A Study Of Human Balance And Coordination Using A Head Mounted Display, Daniel Gracia De Luna

Theses and Dissertations

Virtual Reality (VR) is growing with new technologies and applications. The new technologies help the user to feel more immersed in virtual environments, but interaction and immersion is an area that has not been well studied. Immersion is the feeling and reaction of users while they are in a virtual environment. This investigation is focused on the study of the human balance and coordination when human subjects are inside a virtual environment. Over 60 subjects are studied under an experiment, where their trajectory is captured and analyzed to identify possible differences or similitudes between male and female subjects.

Baja Sae Ecvt Mechanical Design, Tyler Lee Connel, Will Daniel Antes, Matt Stephen Balboni, Benjamin James Colard, Julian Edward Finburgh

Mechanical Engineering

This objective of this project was to design, manufacture, and test the mechanical systems of an electronically-controlled continuously variable transmission (eCVT) for the Cal Poly Baja SAE vehicle.

Binder Jetting: A Review Of Process, Materials, And Methods, Mohsen Ziaee, Nathan B. Crane

Faculty Publications

Binder Jet printing is an additive manufacturing technique that dispenses liquid binding agent on powder. Layers are formed repeatedly to build up a physical article. Binder jetting (BJ) can be adapted to almost any powder with high production rates. The BJ process utilizes a broad range of technologies including printing methods, powder deposition, dynamic binder/powder interaction, and post-processing methods. A wide variety of materials have been demonstrated including polymers, metals, and ceramics, but a common challenge is developing printing and post-processing methods that maximize part performance. This article presents a broad review of technologies and approaches that have been applied …

System Integration Of C-Arm Robotic Prototype Using Motion Capture Guidance For Accurate Repositioning, Alireza Yazdanshenas

Mechanical Engineering Theses

One of the important surgical tools in spinal surgery is the C-Arm X-ray System. The C-Arm is a large “C” shaped and manually maneuvered arm that provides surgeons and X-ray technicians the ability to take quick quality X-rays during surgery. Because of its five degrees of freedom, the C-Arm can be manually maneuvered around the patient to provide many angles and perspectives, ensuring surgical success.

This system works fine for most surgical procedures but falls short when the C-Arm must be moved out of the way for complicated surgical procedures.

The aim of this thesis is to develop an accurate …

Stress Corrosion Cracking Resistance Of Cold-Sprayed Al 6061 Deposits Using A Newly Developed Test Fixture, Mala M. Sharma, Jeremy Schreiber, Timothy Eden, Victor Champagne

Faculty Journal Articles

The stress corrosion cracking (SCC) response of Al 6061 bulk deposits produced by high-pressure cold spray (HPCS) was investigated and compared to commercial wrought Al 6061-T6 material. Representative tensile coupons were stressed to 25%, 65% and 85% of their respective yield strength and exposed to ASTM B117 salt fog for 90 days. After exposure, the samples were mechanically tested to failure, and subsequently investigated for stress corrosion cracking via optical and scanning electron microscopy with energy-dispersive X-ray spectroscopy (EDS). The results were compared to the wrought Al 6061-T6 properties and correlated with the observed microstructures. Wrought samples showed the initiation …

Engineering Of Bio-Mimetic Substratum Topographies For Enhanced Early Colonization Of Filamentous Algae, Ali Khoshkhoo, Andres L. Carrano, David M. Blersch, Kamran Kardel

Manufacturing Engineering: Faculty Publications (2015-2023)

This work reveals a set of surface topography parameters that are significant for algal attachment to natural rock substrata. Topography analysis of rock surfaces from a stream identifies three descriptive areal parameters (Smr, Sv, and Sa) that correlate with the presence of natural periphyton community. A method was developed and validated to reverse engineer and manufacture artificial substrata with topographic complexity defined by these parameters, using computational modeling and additive manufacturing. Results from colonization experiments with filamentous algae show statistically significant increases in early biomass accrual rates on substrata with higher values of …

Maquiladoras In Central America: An Analysis Of Workforce Schedule, Productivity And Fatigue., Jose L. Barahona

Masters Theses & Specialist Projects

Textile factories or Maquiladoras are very abundant and predominant in Central American economies. However, they all do not have the same standardized work schedule or routines. Most of the Maquiladoras only follow schedules and regulations established by the current labor laws without taking into consideration many variables within their organization that could affect their overall performance. As a result, the purpose of the study is to analyze the current working structure of a textile Maquiladora and determine the most suitable schedule that will abide with the current working structure but also increase production levels, employee morale and decrease employee fatigue. …

Bioprinting With Human Stem Cell-Laden Alginate-Gelatin Bioink And Bioactive Glass For Tissue Engineering, Krishna C. R. Kolan, Julie A. Semon, Bradley Bromet, D. E. Day, Ming-Chuan Leu

Biological Sciences Faculty Research & Creative Works

Three-dimensional (3D) bioprinting technologies have shown great potential in the fabrication of 3D models for different human tissues. Stem cells are an attractive cell source in tissue engineering as they can be directed by material and environmental cues to differentiate into multiple cell types for tissue repair and regeneration. In this study, we investigate the viability of human adipose-derived mesenchymal stem cells (ASCs) in alginate-gelatin (Alg-Gel) hydrogel bioprinted with or without bioactive glass. Highly angiogenic borate bioactive glass (13-93B3) in 50 wt% is added to polycaprolactone (PCL) to fabricate scaffolds using a solvent-based extrusion 3D bioprinting technique. The fabricated scaffolds …

Zinc Ferrite Based Gas Sensors: A Review, Kaidi Wu, Jianzhi Li, Chao Zhang

Manufacturing & Industrial Engineering Faculty Publications

Flammable, explosive and toxic gases, such as hydrogen, hydrogen sulfide and volatile organic compounds vapor, are major threats to the ecological environment safety and human health. Among the available technologies, gas sensing is a vital component, and has been widely studied in literature for early detection and warning. As a metal oxide semiconductor, zinc ferrite (ZnFe2O4) represents a kind of promising gas sensing material with a spinel structure, which also shows a fine gas sensing performance to reducing gases. Due to its great potentials and widespread applications, this article is intended to provide a review on the latest development in …

Micro-Ct Evaluation Of Defects In Ti-6al-4v Parts Fabricated By Metal Additive Manufacturing, Haijun Gong, Venkata Karthik Nadimpalli, Khalid Rafi, Thomas Starr, Brent Stucker

Manufacturing Engineering: Faculty Publications (2015-2023)

In this study, micro-computed tomography (CT) is utilized to detect defects of Ti-6Al-4V specimens fabricated by selective laser melting (SLM) and electron beam melting (EBM), which are two popular metal additive manufacturing methods. SLM and EBM specimens were fabricated with random defects at a specific porosity. The capability of micro-CT to evaluate inclusion defects in the SLM and EBM specimens is discussed. The porosity of EBM specimens was analyzed through image processing of CT single slices. An empirical method is also proposed to estimate the porosity of reconstructed models of the CT scan.

Cisco Nexus 9200 Robustness Redesign, Colin Berge, Ethan Gold, Cole Christopherson, Rahul Makhijani

Industrial and Manufacturing Engineering

Certain configurations of Cisco's Nexus 9200 product experienced issues with bending during shipping. Two solutions were developed to eliminate this problem: an external brace that could quickly address the problem yet was expensive and unsustainable, and a redesigned chassis, which was more economical but came with a longer time to implement. Real world packaging and shipping conditions were simulated in SolidWorks and Finite Element Analysis was used to model the stresses experienced when the product is dropped. Both designs were found to significantly reduce stress in critical areas, thus reducing the chance of failure and the cost of the problem. …

Fluid Power Vehicle Challenge - The Incompressibles - Final Design Report, Nicholas Gholdoian, Russell Posin, David Vitt, Alex Knickerbocker, Kyle Franck, Julian Rodkiewicz

Mechanical Engineering

This report provides a comprehensive description of the research, analysis and design work that The Incompressibles have completed thus far in the senior project process. This document includes all the work that The Incompressibles have completed for the team’s Preliminary Design Review (PDR), Critical Design Review (CDR), the work leading up to the 2019 FPVC competiton and the competition results. This report includes the initial research that the team completed for the fluid power competition, first iterations of designs, final iterations of designs, manufacturing results and processes, and finally testing and results from competition. With a new design for the …

Insulated Solar Electric Cooker Immersion Heater, Emily Burnside, Kaeley Dicks, Joshua R. Stevens, Brady Banks

Mechanical Engineering

This report is the final design review (FDR) report for our team completing the Insulated Solar Electric Cooker (ISEC) Immersion Heater mechanical engineering senior project. The goal of this project is to standardize and perform analysis on a preexisting, inexpensive solar-powered immersion heater for cooking use in developing countries, reducing the adverse effects presented by traditional biomass cooking fires. We also designed a manufacturing process to improve repeatability and to reduce labor investment of heater production. The ISEC research team from the California Polytechnic State University Physics Department have been working on the development of this immersion heater and have …

Bulk-Explosion-Induced Metal Spattering During Laser Processing, Cang Zhao, Qilin Guo, Xuxiao Li, Niranjan Parab, Kamel Fezzaa, Wenda Tan, Lianyi Chen, Tao Sun

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Spattering has been a problem in metal processing involving high-power lasers, like laser welding, machining, and recently, additive manufacturing. Limited by the capabilities of in situ diagnostic techniques, typically imaging with visible light or laboratory x-ray sources, a comprehensive understanding of the laser-spattering phenomenon, particularly the extremely fast spatters, has not been achieved yet. Here, using MHz single-pulse synchrotron-x-ray imaging, we probe the spattering behavior of Ti-6Al-4V with micrometer spatial resolution and subnanosecond temporal resolution. Combining direct experimental observations, quantitative image analysis, as well as numerical simulations, our study unravels a novel mechanism of laser spattering: The bulk explosion of …

C6 Wheels, Samuel L. Pizot, Luke Martin, Josh Warner, Jonah Levis

Mechanical Engineering

This document details the C6 Wheels project being undertaken for senior design. The objective is to design and manufacture carbon fiber reinforced polymer wheels for the Cal Poly Formula Society of Automotive Engineers (FSAE) team. The wheel shells will be used on FSAE’s competition vehicles. FSAE requested the wheels to improve the handling characteristics of their vehicles by reducing the unsprung and rotational mass. They have attempted carbon fiber wheels previously but have not yet run any on their vehicles. FSAE specifically proposed the design of carbon fiber shells with an aluminum center as opposed to full carbon fiber wheels …

Nano Fab Lab 63, Brian K. Deemer, Josh Clemons, Nick Brodine, Delaney Fitzsimmons

Mechanical Engineering

Lawrence Livermore National Laboratories (LLNL) has several steps in the production process for ceramic nanofiber tubes that they would like to improve - electrospinning, cutting, rolling, sealing and heat treating. We undertook the challenge to deliver LLNL with a semi-automated process that efficiently integrates the steps of cutting, rolling, and sealing to save time and improve control over end dimensions. In this document, we discuss the technical background of the manufacturing steps currently followed to create nanofiber tubes, identify which steps are incorporated in our prototype and explain how they will interface with one another, define the design requirements, present …

Evaluation Of Tensile Properties For Selective Laser Melted 316l Stainless Steel And The Influence Of Inherent Process Features, Paul Swartz

Master's Theses

Optimal print parameters for additively manufacturing 316L stainless steel using selective laser melting (SLM) at Cal Poly had previously been identified. In order to further support the viability of the current settings, tensile material characteristics were needed. Furthermore, reliable performance of the as-printed material had to be demonstrated. Any influence on the static performance of parts in the as-printed condition inherent to the SLM manufacturing process itself needed to be identified. Tensile testing was conducted to determine the properties of material in the as-printed condition. So as to have confidence in the experimental results, other investigations were also conducted to …

Adapted Trailer Hitching System, Joseph Neil Hearn, Maxwell M. Selna, Maximilian D. Cossalter, Eric B. Ringsrud

Mechanical Engineering

This report highlights the entire design process of an adapted trailer hitching system for Taylor Morris: a navy veteran and quadruple amputee. This begins with problem definition through customer and product research. Objectives are generated after the problem is defined and the boundary of the project is set. This outcome of the project focuses on modifications/improvements to the vehicle side of the problem and leaves the trailers untouched. Engineering specifications are developed to constrain the concept design direction, which ultimately dictates the outcome of the final design. The final design is used as a basis to manufacture a structural prototype …

Modifying Casting Parameters To Improve The High Temperature Ductility Of Investment Cast Nickel-Based Superalloy Pwa 1455, Lars Alexander Hedin, Cole Magnum Introligator

Materials Engineering

PCC Structurals, an industry leader in superalloy investment castings, has observed inconsistencies in the stress rupture performance of polycrystalline nickel-based superalloy PWA 1455. PCC has changed their casting parameters to reduce the thermal gradient during cooling but have been unable to correlate these changes with an increase in stress rupture elongation. Metallographic examination of past samples indicated microstructures composed of non- equiaxed dendritic grains with mean diameter of .021 inches along the test axis. A similar study on polycrystalline superalloys has indicated that excessive superheat temperatures above the liquidus can result in large grains identical to those observed, limiting the …

Redesign Of Cubesat For Beam Charging, Kuba Preis

Industrial and Manufacturing Engineering

This paper is intended to be a study in the applications of the design freedom granted by additive manufacture in the design of a 1U CubeSat frame. The main loads experienced by a CubeSat are structural (during launch) and thermal (solar radiation). Beam charging is an emerging technology which involves charging a CubeSat using a laser beam. In this paper, a CubeSat frame was redesigned to account for the structural loads induced during launch and the thermal loads induced when beam charging. The thermal, weight, design, and structural requirements for a new CubeSat design were derived. The 1U CubeSat frame …