Mechanical Engineering Commons^™

Studying And Troubleshooting Lubricity Test On Pressure Wire X Proximal And Distal Coatings, Usama A. Khan

All Graduate Theses, Dissertations, and Other Capstone Projects

Coatings of guidewires used in medical device manufacturing industry are one of the most important element aspects. It defines its efficiency to penetrate through tightest of canals and curves. Guidewires are put through controlled environment to accelerate its age and tested for its mechanical features. Pressure Wire X failed the lubricity testing after being tested by multiple operators and at alternate sites. A cause-and-effect diagram shows all potential causes of test failure. The human factor involved in the test failure was investigated through multiple Gage R&R and training records. Calibration error with the lubricity tester DL1000 was identified and solved …

Design And Development Of Smart Wardrobe Technology, Mikhail Filatov

All Graduate Theses, Dissertations, and Other Capstone Projects

The increasing demand for online shopping in the 21st century is causing rapid growth in technology and methods in marketing and sales fields. Present thesis work scrutinizes the process of design and development of the device that simplifies the process of trying on and buying clothes in online retail stores, the development of which is based on the known basics of operational, mechanical, and electrical designs for computational systems, with account for ergonomics and manufacturing sustainability. The following research represents the market analysis for competition identification, description of all operational modes of the system, list of mechanical and electrical components …

A Semantic Web Approach To Fault Tolerant Autonomous Manufacturing, Fadi El Kalach, Ruwan Wickramarachchi, Ramy Harik, Amit Sheth

Publications

The next phase of manufacturing is centered on making the switch from traditional automated to autonomous systems. Future factories are required to be agile, allowing for more customized production, and resistance to disturbances. Such production lines would be able to reallocate resources as needed and minimize downtime while keeping up with market demands. These systems must be capable of complex decision-making based on parameters such as machine status, sensory/IoT data, and inspection results. Current manufacturing lines lack this complex capability and instead focus on low-level decision-making on the machine level without utilizing the generated data to its full extent. This …

Investigation Of Microstructurally Dependent Mechanical Properties Of Cold Sprayed Copper Using Correlative Microscopy, Quintin Otto

UNF Graduate Theses and Dissertations

This project employs multi-instrument materials characterization to analyze material made with the “Cold Spray” additive manufacturing process. Cold spray is an emerging additive manufacturing technique with unique benefits resulting from its low temperature adhesion process induced by plastic deformation. Metallic powder collides at high speeds creating three dimensional materials and coatings without the need for melting. Copper cold sprayed specimens were analyzed using a series of imaging techniques to characterize the microstructure at varying levels of detail and magnification. Scanning electron microscopy and electron back scattered diffraction were paired with microhardness testing to generate a correlative comparison between microstructure and …

Modified Reactive Sputter Deposition Of Titanium Nitride Thin Films Via Hipims With Kick-Pulse And Improvement Of The Structure-Zone Model, Andrew Miceli

UNF Graduate Theses and Dissertations

Direct current (DC) and radio frequency (RF) sputtering methods have been commonplace in industry for several decades and widely studied in literature. Hard films of nitrides, such as titanium nitride (TiN), have been deposited using reactive DC sputtering onto cutting tools and medical devices extensively as well. For these applications, the films require excellent adhesion, high density, and high hardness. High-Power Impulse Magnetron Sputtering (HIPIMS) has emerged over the last several years as a method to produce films with increased density and mechanical properties. Process-structure-property relationships for reactive HIPIMS are not yet well developed. Additionally, conventional HIPIMS suffers from relatively …

Urban Farming: Empowerment To Increase Economic, Education, And Nutritional Benefit For The Sub-Urban Community, Nasruddin Nasruddin, Yusuf Donner Dwiyantama, Banu Muhammad, Anom Bowalaksono, Dian Ayubi, Sarah Islamiati Pertiwi

ASEAN Journal of Community Engagement

This article discusses the urban farming program at Sekolah Master in Beji, Depok, Indonesia, which aims to provide the community with broader benefits, such as economy, education, and increased nutritional value. The project involves planting method that was introduced to this school community. The program itself consists of several stages, starting from the preparation—dissemination of the program and designing a plan for the greenhouse, the implementation—constructing the greenhouse and installing the automatic water system, planting the vegetation, and monitoring and evaluation of the program. Eventually, an evaluation of the successful program is required to determine whether the program can be …

Experimental And Numerical Studies On Laser Hot Wire Cladding By A High-Power Direct Diode Laser, Mingpu Yao

Mechanical Engineering Research Theses and Dissertations

Laser hot wire cladding is an advanced surface modification technology. It has been extensively growing during the last decades due to its high deposition rate, good metallurgical bonding between the substrate and clad layer, low dilution ratio, and small heat-affected zone. There are many kinds of lasers widely used in the laser cladding process. The high-power direct diode laser is widely welcomed because of its high energy efficiency, high electro-optic conversion efficiency, low cost, and high reliability. A rectangular-shaped direct diode laser beam combined with hot wire feeding can achieve a lower dilution depth with a uniform fusion line compared …

Multiple Objective Function Optimization And Trade Space Analysis, Yifan Xu

All Theses

Optimization can assist in obtaining the best possible solution to a design problem by varying related variables under given constraints. It can be applied in many practical applications, including engineering, during the design process. The design time can be further reduced by the application of automated optimization methods. Since the required resource and desired benefit can be translated to a function of variables, optimization can be viewed as the process of finding the variable values to reach the function maxima or minima. A Multiple Objective Optimization (MOO) problem is when there is more than one desired function that needs to …

Callaway Measurement Device, Andre S. Fisher, Roman Hays, Blake Sousa, Grant Gabrielson

Mechanical Engineering

The purpose of this document is to illustrate the Callaway Measurement Device senior project from start to finish. The challenge given to the team was to update and improve a gauge used by Callaway employees to measure the loft, lie, and face angle of their full spectrum of golf clubs. Once the team understood how the pre-existing gauge operates, the team conducted background research into other technologies that could improve the gauge. The team decided to digitalize the device amongst other tweaks to reduce error. Because the CAD files were not available for the pre-existing device, the team began reverse …

Novel Hitch Cargo Cart, Cesilio Sanchez Ramirez, Lance Haidet, Richard Lontoc, Tyler Selinka

Mechanical Engineering

This document presents the engineering design process used to develop, manufacture, and test a new and improved iteration of a hitch cart prototype. This process was performed by a team of four mechanical engineering seniors as part of California Polytechnic State University, San Luis Obispo’s senior design pathway. The goal of this project was to develop a sturdy and reliable iteration of our sponsor’s hitch cart prototype, that integrated the functionality of a vehicle hitch cargo platform and that of a height adjustable cargo cart into a single streamlined and easy to use product. This design could be used by …

The Deflection And Heat Transfer Analysis Of Injection Mold Cavity With Sla Cooling Channel Insert, Olumide Temidayo Aladesiun

Theses and Dissertations

Fast cooling in injection molding is the critical in the process economy. Among many different cooling channel designs available, conformal cooling offers the best and the most efficient cooling. However, limited awareness, accessibility, complexity, cost, knowledge, and experience limit the use of conformal cooling channels to be used into the mold in a molding process.

Typically, SLM(Selective Laser Melting) method is used to create cavity inserts with conformal cooling channels, however, due to the difficulties listed above, applications of conformal cooling channels are very limited. For an inexpensive alternative SLA (Stereolithography Apparatus) can print cavity inserts with conformal cooling channels. …

Novelty Ice Cream Assembly Prototype, Mason Sylvester, Logan Williamson, Alvaro Martinez, Adin Gilman-Cohen

Mechanical Engineering

Cool Beans USA is a novelty ice cream startup company founded by Keith Zachow. In the winter of 2022, our team began working with Mr. Zachow to develop a machine to automate parts of the production process for his product. This product consists of two hemispherical ice-cream cone shell halves filled with soft serve ice cream and pressed together. The assembled pods are around the size and shape of a small walnut and are intended to be sold in stores as a frozen finger food. At the time of project inception, this product was in its early stages and was …

Rotating Backing Brush, Caleb Savard, David Dalal, Max Allred, Mathis Weyrich

Mechanical Engineering

In the final steps of GAF’s shingle production process, small asphalt particles called fines are applied. Some fines adhere well to the shingle sheet, while others temporarily stick only to fall off the sheet further down the manufacturing line. As a result, the shingle plant floor is covered in fines that have fallen due to vibrations and gravity. The technicians and engineers at GAF want a cleaner working environment and to potentially reuse the loose fines. We are a senior project team that solved this problem by designing a system to remove and collect loose fines. In this document, the …

Baby Soothing Device, Grace Kalene Mekrut, Matteo Gozzini, Miles Angel Ibarra, Christian Joel Roberts

Mechanical Engineering

This document is the official final design review for the Baby Soothing Device. This product is intended to help families sleep throughout the night by allowing a baby to be soothed back to sleep without constant and direct parental interaction. It is maintained by Mechanical Engineering students at California Polytechnic State University, San Luis Obispo for Dustin Yoder, the project sponsor. The purpose of this document is to present the design process from ideation to finished design in great enough detail that its manufacturing procedure may be replicated if desired. This document further explains all the research, testing, and benchmarks …

Fabrication Of Solar Absorber Tube With Internal Fin Structure With In718 And Effect Of Boron With In718 For Solar Absorber Tube Using Selective Laser Melting 3d Printing Technology, Naznin Nuria Afrin

Theses and Dissertations

This research aimed to fabricate Solar Absorber Tubes for Solar-Thermal Power Plant with internal fin structures using Selective Laser Melting (SLM) technology. In this study, we investigated the effect of B with IN718 in 3D printing using SLM for solar absorber tubes. The objective was to study the material-process-properties relationship with goal to identify and validate the optimal parameters for the SLM process. Material selected for this study was IN718 with 0.5% and 1% B particle mixed using a V-shape mixing machine. The flowability test was conducted using the Angle of Repose (AOR) method. 3D printed samples …

A Numerical Simulation Of The Powder Bed Additive Manufacturing Process With Molecular Dynamics Simulation, Yeasir Mohammad Akib

Theses and Dissertations

Many manufacturing industries utilize powder bed fusion (PBF) since it can produce microscale precision 3D parts. During PBF, powder particles are selectively fused layer by layer using thermal energy. The build quality in the PBF process relies heavily on powder bed properties and thermal energy deposition. Powder flowability, spreadability, and packing fraction are some of the insightful factors that determine the quality of the powder bed. In this study, a two-dimensional powder bed is developed using the LAMMPS package. A cloud-based pouring of powders with varying volumes and initialization is adopted for the work. A blade-type and circular recoater is …

Ultrafast Laser Direct Writing Of Conductive Patterns On Modified Polyimide Film For Flexible Electronic Applications, Ishrat Jahan Biswas

Theses and Dissertations

Conductive patterns can be printed on a flexible polymer substrate using the direct laser writing (DLW) method. In order to write conductive circuits in such polymer using a laser, polyimide (PI) is a desirable material choice due to its electrical, chemical, and mechanical properties. Electrically non-conductive PI has shown great potential for flexible printed electronics as LDW enables selective carbonization in the bulk of such material leading to the formation of conductive lines. The technique is shown to be a rapid and minimal cost method for printing electrodes to nanoscale devices. However, investigations in this field show several limitations to …

A Study Of The Surface Properties Of Additive Manufactured Inconel 718 After Laser Surface Treatment And Cnc Grinding, Sampson K. Canacoo

Theses and Dissertations

This study investigated the surface properties of additive manufactured Inconel 718 produced through selective laser melting, and the effects of laser ablation and CNC grinding on the surface finish. The objectives were to investigate the effects of the various parameters of laser ablation and CNC grinding on the Inconel 718 surface. The parameters used for the laser experiments were pulse energy (4, 20, and 30 µJ), scanning speed (5, 10, and 15 mm/s), and hatch distance (10, 30, and 50 µm). For the grinding experiments, the wheel speed was kept constant at 20.3 m/sec, however, two different workpiece speed (8.6 …

Investigation Of Process Parameters To Fabricate Refractory Medium-Entropy Alloy By Selective Laser Melting Process, Abdullah Al Masum Jabir

Theses and Dissertations

This thesis proposal investigates the synthesis of TiWMo refractory medium entropy alloy (RMEA) by selective laser melting process from elemental powder. Steel, titanium and tungsten substrates were used to study the impact on the formation of TiWMo RMEA. Different process parameters were applied to investigate the effects on melting, diffusion and formation of RMEA. The microstructure of TiWMo and elemental distribution were observed by scanning electron microscope (SEM) and energy dispersive X-ray spectroscopy (EDS). SEM analysis revealed that with higher energy density the pores and microcracks were improved. EDS data validated the composition is homogenized and stable after few layers …

Femtosecond Pulse Filamentation In Dielectric Media Toward Photonics Sensor Fabrication, Anitha Narayanan

Theses and Dissertations

Through pulse filamentation, femtosecond laser pulses have been utilized to modify the refractive indices of dielectric materials such as glass, A-plane sapphire crystal, and Cplane sapphire crystal. The 10x Infinity Corrected Lens was used, and the focusing condition was tuned as being the same and fixed to both glass and sapphire crystals. First, 8uJ of laser energy was optimized to produce controlled pulse filamentation voids in the glass. The laser intensity was then optimized to 2-3.5 uJ, 1.5 uJ, & 2.5 uJ, respectively, for the controlled pulse filamentation in A and C plane sapphire crystals. Due to the different crystal …

Feasibility Analysis Of Embedding Optical Fiber Sensor Into Additively Manufactured Part, Mahmudul Hasan Porag

Theses and Dissertations

The research tried to examine the viability of the embedment of optical fiber sensors in Additively built components, packaging the sensors within the components, and characterizing the sensors for sensing a specified measurement. Optical fiber sensors are popular due to their small size, resilience against electromagnetic radiation, and reliability in potentially dangerous conditions. Embedding fibers inside a product allows for the monitoring of critical areas, allowing for preemptive action in the case of a breakdown. Coupons of Inconel 718 were made using laser powder-bed fusion (LPBF), with the fabrication settings tuned to determine whether such a development was possible. After …

Performance Comparison Of Several Control Algorithms For Tracking Control Of Pantograph Mechanism, Laylaa Mahmoud Eng, Mohamed Shamseldin Dr, Mohamed Sallam Dr, Abdelghany Mohamed Prof

Future Engineering Journal

A sort of parallel manipulator known as a pantograph robot mechanism was created primarily for industrial requests that required high precision and satisfied speed. While tracking a chosen trajectory profile requires a powerful controller. Because it has four active robot links and one robot passive link in place of just two links like the open chain does, it can carry more loads than the open chain robot mechanism while maintaining accuracy and stability. The calculated model for a closed chain pantograph robot mechanism presented in this paper takes into account the boundary conditions. For the purpose of simulating the dynamics …

Characterization Of Materials Properties In Additively Manufactured Aisi-420 Martensitic Steel Deposited By Laser Engineered Net Shaping, Md Mehadi Hassan

Nanoscience and Microsystems ETDs

Metal additive manufacturing (AM) is a disruptive technology enabling the fabrication of complex and near-net-shaped parts by adding material layer-wise. It offers reduced lead production time. AM processes are finding applications in many industrial sectors such as aerospace, automotive, biomedical, and mold tooling. Despite the tremendous advantages of AM, some challenges still prevent this technology's adoption in high-standard applications. Anisotropy and inhomogeneity in the mechanical properties of the as-built parts and the existence of pores and lack-of-fusion defects are considered the main issues in directed energy deposition (L-DED) parts. Laser-engineered net shaping LENS® offers excellent possibilities to fabricate metal tools …

Biomass Characterization And Insulation Optimization Studies, Hussein Awad Kurdi Saad

Doctoral Dissertations and Master's Theses

This study indicates how biomass materials can be effectively used as naturally sustainable alternatives to insulation materials. Barley grains and oak leaves, straw, and jute are collected, and crushed into powders/ chopped pieces. The physical characteristics are measured to characterize each powder. The biomass powder reinforced composites are manufactured in varying weight ratios. The density and thermal conductivity of composite materials are measured. The properties of composites compared to those of commercial insulation materials are found to be close to them. Furthermore, genetic algorithms (GA) can be used to achieve multi-objective optimization entailing maximizing insulation (minimizing heat transfer) and simultaneously …

A Machine Learning Approach To Robotic Additive Manufacturing Of Uv-Curable Polymers Using Direct Ink Writing, Luis A. Velazquez

LSU Master's Theses

This thesis presents the design and implementation of a robotic additive manufacturing system that uses ultraviolet (UV)-curable thermoset polymers. Its design considers future applications involving free-standing 3D printing by means of partial UV curing and the fabrication of samples that are reinforced with fillers or fibers to manufacture complex-shape objects.

The proposed setup integrates a custom-built extruder with a UR5e collaborative manipulator. The capabilities of the system were demonstrated using Anycubic resin formulations containing fumed silica (FS) at varying weight fractions from 2.8 to 8 wt%. To fully cure the specimens after fabrication, a UV chamber was used. Then, measurements …

Hypoxic Incubation Chamber, Simone Lisette Helfrich, Makenzie Nicole Jones

Biomedical Engineering: Graduate Reports and Projects

This paper describes the design, manufacturing, and testing of a novel controllable hypoxic incubator with fully functional oxygen gas control and temperature control in a humid environment. On the current market, a majority of the few hypoxic incubators use pre-mixed gas that does not offer precise control over gas concentration. The objective for this project was to create a chamber that allows the user to set the O2 concentration to varying set points of % O2 while maintaining the chamber at a constant body temperature, CO2 level, humidity, and sterility. To start the project, multiple concepts were developed for the …

Hypoxic Incubation Chamber, Simone Lisette Helfrich, Makenzie Nicole Jones

Master's Theses

This paper describes the design, manufacturing, and testing of a novel controllable hypoxic incubator with fully functional oxygen gas control and temperature control in a humid environment. On the current market, a majority of the few hypoxic incubators use pre-mixed gas that does not offer precise control over gas concentration. The objective for this project was to create a chamber that allows the user to set the O2 concentration to varying set points of % O2 while maintaining the chamber at a constant body temperature, CO2 level, humidity, and sterility. To start the project, multiple concepts were developed for the …

A Benchtop Robotic Automation Approach For Manufacturing Prefilled Syringes, Yehua Zhong

All Theses

Automation and robotics have become a staple in the biological manufacturing sector due to their ability to efficiently work without operator inputs, with a high degree of accuracy and repeatability. Industrial robotic arms, in particular, present themselves as valuable tools for biological manufacturing scenarios that require customized solutions due to their ease of programming and flexibility. The traditional hospital-focused healthcare system was organically developed to address acute conditions, however, in recent years, due to the unprecedented occurrence of emergencies happening more frequently, fast and efficient drug production becomes important [17]. This thesis represents the use of a benchtop robot and …

A Survey Of Smart Manufacturing For High-Mix Low-Volume Production In Defense And Aerospace Industries, Tanjida Tahmina, Mauro Garcia, Zhaohui Geng, Bopaya Bidanda

Manufacturing & Industrial Engineering Faculty Publications

Defense and aerospace industries usually possess unique high-mix low-volume production characteristics. This uniqueness generally calls for prohibitive production costs and long production lead-time. One of the major trends in advanced, smart manufacturing is to be more responsive and better readiness while ensuring the same or higher production quality and lower cost. This study reviews the state-of-the-art manufacturing technologies to solve these issues and previews two levels of flexibility, i.e., system and process, that could potentially reduce the costs while increasing the production volume in such a scenario. The main contribution of the work includes an assessment of the current solutions …

Reliability Study Of A New Electromechanical Device Designed To Measure The Relative Dorsal Mobility Of The First Ray Of The Foot, Philippe Passeraub

Faculty Publications

Introduction: A new electromechanical instrument has been developed to measure relative dorsal mobility of the first ray in an objective and reliable way by simulating ground reaction forces during gait. This device equally applies a standardized, electronically controlled, and precise force under the first metatarsal head M1 as well as under the heads of the lesser metatarsals M2 to M5. The relative dorsal mobility between these two bearings is then measured. The purpose of this study is to assess the intra- and inter-examiners reliabilities of the measurements obtained with this device. Methods: The protocol included two examiners and 36 feet …