Mechanical Engineering Commons^™

Development Of A Low Cost Imaging System For A Laser Metal Deposition Process, Shyam Barua, Todd E. Sparks, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The size of the melt pool created by the laser is one of the most important quality characteristic in a laser metal deposition process. This paper discusses the development of a low-cost vision system to automatically determine the size of the melt pool for in-process control. To cope with the intense infrared signal from the laser and melt pool, external ultraviolet illumination is paired with narrow bandpass filters on a usb microscope to achieve a clear image of the melt pool. The sensitivity of the melt pool to changes in system parameters and various substrate materials are also evaluated.

Effect Of Different Graphite Materials On Electrical Conductivity And Flexural Strength Of Bipolar Plates Fabricated By Selective Laser Sintering, Nannan Guo, Ming-Chuan Leu

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Graphite is an excellent material for bipolar plates used in Proton Exchange Membrane (PEM) fuel cell due to its great chemical resistance, but the brittle nature makes it difficult to manufacture. Selective Laser Sintering (SLS) based on layer-by-layer manufacturing technology can fabricate graphite bipolar plates with complex gas flow channels. To improve the performance of bipolar plates including electrical conductivity and flexural strength, different graphite materials (natural graphite, synthetic graphite, carbon black, and carbon fiber) were investigated to fabricate test samples. These samples then went through post processing including carbonization and infiltration. The results show that bipolar plates with electrical …

Selective Laser Sintering And Freeze Extrusion Fabrication Of Scaffolds For Bone Repair Using 13-93 Bioactive Glass: A Comparison, Krishna C. R. Kolan, Nikhil P. Doiphode, Ming-Chuan Leu

Mechanical and Aerospace Engineering Faculty Research & Creative Works

13-93 glass is a third-generation bioactive material which accelerates the bone’s natural ability to heal by itself through bonding with surrounding tissues. It is an important requirement for synthetic scaffolds to maintain their bioactivity and mechanical strength with a porous internal architecture comparable to that of a human bone. Additive manufacturing technologies provide a better control over design and fabrication of porous structures than conventional methods. In this paper, we discuss and compare some of the common aspects in the scaffold fabrication using two such processes, viz. selective laser sintering (SLS) and freeze extrusion fabrication (FEF). Scaffolds fabricated using each …

Uncertainty Analysis In Laser Deposition Finish Machining Operations, Jomy Francis, Todd E. Sparks, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The Laser Aided Manufacturing Process (LAMP) from Missouri S&T is a laser based metals rapid manufacturing process that uses machining to improve the final part's surface finish. When free-form machining, the absence of enough deposited material results in inconsistent scallop heights which result in poor surface finish or incorrect geometry in the final part. This paper investigates a probabilistic approach to various uncertainties involved in the deposition and subsequent machining of an arbitrary part. Furthermore, this paper analyses the machine errors which makes the response of Scallop Height to exceed the predefined maximum scallop height when traveling along the tool …

Development Of A Task Assignment Tool To Customize Job Descriptions And Close Person-Job Fit Gaps, Bryan W. Booker

Dissertations

Does the knowledge worker fit the job or should the job fit the knowledge worker? This research developed a methodology and a tool to customize a knowledge worker’s job design to better fit their knowledge, skills, abilities and characteristics. The research outcomes support the customization of the job design to improve person-job fit, the documentation of the customized job design as a position description, and the use of a structured person-task assignment process. The recommended task assignment process includes a job aid that uses multivariate equations to predict expected task performance. Data were collected from two knowledge worker sub-groups: lean …

An Analytic Hierarchy Process Approach To Assess Health Service Quality, Yan Li

Theses and Dissertations - UTB/UTPA

While improving quality in health care is currently at the forefront of professional, political, and managerial attention, the key dimensions constituting health-care quality have not been fully understood. Also, few valid approaches have been proposed to the measurement of health-care quality. In this research, the Analytic Hierarchy Process (AHP) approach is applied to study the structure of health-care quality and deducted relative importance weights for each of the quality elements. A statistical quality model is derived to assess medical equipment quality which is an important part constituting the general health-care quality. Finally, the application of the AHP model to assess …

A Stochastic Product Priority Optimization Method For Remanufacturing System Based On Genetic Algorithm, Xiong Xiong

Theses and Dissertations - UTB/UTPA

Increasing number of manufacturers are developing remanufacturing facilities to recover end-of-life products for product/component reuse and material recycling while the high uncertainty pattern of returned products complicates the production planning. In this thesis a stochastic production priority optimization method, considering various priority concerns for remanufacturing systems is developed. Priority ranking and matching algorithm is developed to determine the priority rule, using thirteen weighting factors. Queueing models are developed to formulate the objective function, a genetic algorithm is then developed to search optimal solution under different business configurations. Result of this research will provide insights to priority assignment mechanism, which in …

An Experimental Investigation Of Friction Bit Joining In Az31 Magnesium And Advanced High-Strength Automotive Sheet Steel, Rebecca Gardner

Theses and Dissertations

Friction Bit Joining (FBJ) is a recently developed spot joining technology capable of joining dissimilar metals. A consumable bit cuts through the upper layer of metal to be joined, then friction welds to the lower layer. The bit then snaps off, leaving a flange. This research focuses on FBJ using DP980 or DP590 steel as the lower layer, AZ31 magnesium alloy as the top layer, and 4140 or 4130 steel as the bit material. In order to determine optimal settings for the magnesium/steel joints, experimentation was performed using a purpose-built computer controlled welding machine, varying factors such as rotational speeds, …

Testing The Test: Validity And Reliability Of Senior Exit Exam, Lizabeth Schlemer, Daniel Waldorf

Industrial and Manufacturing Engineering

A senior exit exam is considered an excellent direct measure of student learning for ABET assessment, but the usefulness of the information gathered is related to the validity and reliability of the test itself. The Industrial and Manufacturing Engineering Department at California Polytechnic State University, San Luis Obispo has used a content exam for several years. This paper will discuss test development, administration, and the role it plays in the assessment process. In addition, the test is evaluated using the standard psychometric techniques of reliability and validity. The results of the evaluation are used to refine the test. The importance …

Natural Fibers And Fiberglass: A Technical And Economic Comparison, Justin Andrew Zsiros

Theses and Dissertations

Natural fibers have received attention in recent years because of their minimal environmental impact, reasonably good properties, and low cost. There is a wide variety of natural fibers suitable for composite applications, the most common of which is flax. Flax has advantages in tensile strength, light weight, and low cost over other natural fibers. As with other natural and synthetic fibers, flax is used to reinforce both thermoset and thermoplastic matrices. When flax is used in thermoplastic matrices, polypropylene and polyethylene are the main resins used. Although at first glance flax may seem to be a cheaper alternative to fiberglass, …

Testing Guidelines For New Product Development, Derek W. Egbert

Theses and Dissertations

While many literary sources outline the product development process, few make mention of the prototyping and testing stage. This thesis suggests that because of its importance in the product development process, "Testing" should be documented as a major step and not just listed as a side note. As part of the testing step, it is suggested that standardized, in-use, and market tests be used to properly evaluate a product. While many rely solely on standardized tests to validate their products, effective in-use tests can be another vital tool that can prove the performance of the product in more specific and …

Development And Assessment Of A Pcb Layout And Manufacturong Laboratory Module In Introductory Electric Circuits For Ee And Non-Ee Majors, Albert Liddicoat, Jianbiao Pan, James G. Harris, Gary Perks, Linda Shepherd

Industrial and Manufacturing Engineering

In standard introductory electric circuits laboratories for electrical engineering (EE) majors and non-EE majors, prototype boards are typically used to construct and test electric circuits. Students typically do not learn how to design and manufacture Printed Circuit Boards (PCB) that are commonly used in more sophisticated design projects and other engineering applications. This paper will present the development and assessment of a PCB layout and manufacturing laboratory module that has been used in introductory electric circuits laboratories for EE and non-EE majors. The feasibility of integrating the new PCB layout and manufacturing module into the electric circuit course will be …

Assessing Curriculum Improvement Through Senior Projects, Jianbiao Pan, Albert Liddicoat, James G. Harris, Linda Shepherd

Industrial and Manufacturing Engineering

Senior project and/or capstone design courses are intended to provide a culminating design experience for students and to demonstrate their understanding of engineering knowledge and their ability to apply that knowledge to practical problems. It is expected that the quality and attributes of students’ senior design projects can be used as a good measure of determining how well the curriculum prepares students to engage in engineering design as well as a measure of faculty teaching and student learning. This paper reports the results of a study designed to assess whether the new computer engineering curriculum implemented at Cal Poly over …

Ground Support Equipment For Northrop Grumman Massive Heat Transfer Experiment, Michael A. Manuel, Christopher J. Sparber, Greg A. Trent

Aerospace Engineering

California Polytechnic State University students designed, built, and certified ground support equipment for the Northrop Grumman Massive Heat Transfer Experiment. The Cal Poly design team built the 10000, 20000, and 30000 assemblies to meet Northrop Grumman requirements. The requirements included interface limitations, design load factors, delivery, and testing specifications. The design process consists of requirements generation, conceptual design, preliminary design, design reviews, manufacturing, and certification. The hardware was successfully completed and is used at the Johnson Space and Kennedy Space Center.

The Applications And Limitations Of Printable Batteries, Matthew Delmanowski

Graphic Communication

This study focuses on the potential applications for printed batteries and how they could affect the printing industry. It also analyzes the main problems associated with manufacturing this technology and what needs to be done to overcome these issues. To find the answers to these questions, two methods of research were used. The first was through the elite and specialized interviewing of Dr. Scott Williams of Rochester Institute of Technology and Professor Nancy Cullins from Cal Poly. The second form of research was a common, yet useful, method called secondary research. This entailed looking at recent written research papers about …

Laser Clean Room Re-Design: A Manufacturing Facility Re-Layout, Jennifer J. Siu

Industrial and Manufacturing Engineering

Alcon’s Laser Clean Room fosters inefficient production practices, is outdated for its current process, and lacking in clear process/product flow. A facility re-design is applied to bring order, efficiency, and optimize flow in the laser production lines.

Deliverables include a new layout that decreases product travel distances and increases productivity as well as an implementation plan and cost/savings analysis. Major design decisions include downsizing the clean room, sorting to find waste and establishing clear process/product flows. The design was implemented within three weeks and results yield 29% reduction of product travel distance, 10.4 hrs/day saved from eliminated gowning time and …

Gas-Assisted Powder Injection Molding: A Comparison Of Residual Wall Thickness Between Metal Cavity Vs. Sla Cavity And Effect Of Mold Temperature On Residual Wall Thickness, Donghan Kim

Theses and Dissertations - UTB/UTPA

The effects of processing variables on gas penetration depth and Residual Wall Thickness (RWT) in an aluminum (Al) cavity of Gas-Assisted Injection Molding (GAIM) were investigated with Polypropylene (PP) and Stainless Steel Powder Feedstock (SSPF). The selected processing variables were melt temperature, shot size, gas pressure, and gas delay time. By using a Taguchi L9 array, the results were compared with previous work. For PP, there were no significant differences on gas penetration depth. However, the significance of gas delay time was relatively higher in an Al cavity as compared to a Stereolithography (SLA) cavity from previous work with SSPF. …

An Information Technology Suitability Index For Mass Customization, Oscar Leonardo Barrenechea

Theses and Dissertations - UTB/UTPA

In today’s manufacturing world, high competitive markets are pushing companies to find better ways to satisfy their customer’s needs using several Mass Customization (MC) approaches. Consequently, new Information Technologies (IT) have taken a very important role in order to manage the increasing amount of data generated from those customers. The purpose of this thesis is to develop an IT suitability index for MC that would help to identify the critical IT factors to be addressed in order to efficiently support MC. A linear programming regression model was utilized to generate index values. Finally, the results of this model could be …

Adaptive Cutting Force Control For Process Stability Of Micro Ultrasonic Machining, Ala'a M. Al-Okaily

Department of Industrial and Management Systems Engineering: Dissertations, Theses, and Student Research

The growing demand for miniaturized products motivates the advancement in micromanufacturing processes research and development. Micro Ultrasonic Machining (Micro USM) is a downscaled version of a macro USM process that is developed to fabricate complex features in chemically inert, nonconductive, hard, brittle materials such as quartz, glass, and ceramics. These materials have many applications in various fields such as optics, electronics, MEMS, and biotechnology. The micro USM process stability is hard to accomplish, because it is highly influenced by the accuracy of the machining system and the variation of the process control parameters. The repeatability of micro USM machined features …

Online Real-Time Water Quality Monitoring And Control System, Paul Duffy, Gerard Woods, James Walsh, Michael Kane

Conference Papers

No abstract provided.

Using Sports Coaching Techniques To Enhance Project Based Learning Instruction, Lizabeth Schlemer, Faith Mimnaugh

Industrial and Manufacturing Engineering

As instructors attempt to apply project based learning as a preferred pedagogy for many aspects of engineering education, countless questions are raised. For instance, how do instructors assess individual performance in a team based environment? How do instructors prepare students for the culminating presentation or report? How do instructors develop the students individually? After reviewing literature on both project based learning and exceptional coaching, we have found that much can be learned from John Wooden, Phil Jackson and other coaches. This paper will organize some of the best practices in sports coaching and draw parallels that will enhance student learning …

Investigation Of Rf Curing Parameters In Resin Infusion Molding, Christopher K. Love

Theses and Dissertations

The purpose of this study is to investigate RF or Radio Frequency energy as a viable alternative to traditional heating methods for the purpose of curing resins used in resin infusion molding, a molding system for polymeric composites. Traditional heating/curing methods include technologies such as room temperature, oven, microwave, infrared, and ultraviolet. Although RF curing provides far more advantages than disadvantages, its implementation into a manufacturing process can be challenging. Specifically, three critical elements must be present in order for RF to function in a manner that is profitable to the manufacturer. Those elements are: (1) the proper generator (voltage …

Building A Successful Transatlantic Collaboration In Engineering/Technological Education; Lessons From A Six Year Journey, Donal Mchale, Mark Mcgrath, John Lawlor

Conference Papers

This paper reflects on key learning’s from the first six-years (2004-2010) of the development of a collaborative journey of two trans-Atlantic higher-educational institutions. It describes the progress towards building a sustainable and innovative international educational partnership in Engineering/Technological education between the Technological University Dublin,DublinIrelandandPurdue University,Indiana,USA.

In particular, the paper provides insight into the iterative stages of development of this relationship. It reflects on some of the key challenges and it recognises the critical enablers of success. It focuses on challenges and solutions in the following six important areas

(i) The partnership initiation stage. Key considerations and important enablers of future …

Functionally Graded Materials By Laser Metal Deposition (Preprint), Syamala R. Pulugurtha, Joseph William Newkirk, Frank W. Liou, Hsin-Nan Chou

Materials Science and Engineering Faculty Research & Creative Works

Fabrication of functionally graded materials (FGMs) by laser metal deposition (LMD) has the potential to offer solutions to key engineering problems over the traditional metalworking techniques. But the issues that need to be addressed while building FGMs are intermixing in the layers and cracking due to the residual stresses. This paper is to present the study of the effect of process parameters (laser power and travel speed) on the degree of dilution between the substrate (or, previous layer) and powder material for few metallurgical systems.

Process Design For Aeration Of Facial Prosthetic, Nathaniel J. Urciuoli

Industrial and Manufacturing Engineering

Facial prosthetics are becoming a necessary step for the recovery of injured veterans and civilians who have suffered severe facial burning. Current users of such prosthetics are not able to wear the prosthetic for an extended period of time due to uncomfortable conditions created by the silicone material. A solution for this problem was to develop a process for creating small holes similar to skin pores that will both ventilate and aid in the evaporation of accumulated sweat under the prosthetic.

The main steps of this process were to create a flexible fixture capable of supporting and securing the prosthetic …

Design Of A Low Cost Powered R/C Combat Airplane And Manufacturing Plan, Jonathan N. Bailey

Industrial and Manufacturing Engineering

The goals of this project are to design a low cost powered remote control combat airplane capable of outdoor flight, named the Aero EX and to develop a manufacturing plan to produce each unit at a selling price of $200, while operating at a 25 vehicle batch rate inside a 1,000 square foot facility. These goals are achieved using: Aerospace fundamentals to design the vehicle, Design for Manufacturability to optimize the design for minimal use of labor, Design for Assembly to give consumers the ability to build the vehicle without fixtures, Pull production to eliminate scheduling and match customer demand. …

Design For Manufacturing Of Sports Equipment, Cedrick Bit, Christopher L. Head

Industrial and Manufacturing Engineering

The purpose of this project was to validate industrial designs for a product in its conceptual stage and suggest/implement design changes that suit the contracting company’s needs while assuring the product maintains its basic functional requirements. Techniques and methods used to validate the design include 3‐D solid modeling, physical product application using rapid prototyping to produce the product. Methods of design for manufacturing were analyzed in the design. Processes used in the validation and verification of the design include solid modeling design, methods of measurements, fixture design and manufacturing processes. Full design specifications and solid model files were finalized and …

Dual Axis Solar Tracker, Weston Sapia, Jason Birnie

Electrical Engineering

No abstract provided.

Maskless Additive Manufacturing Of Micro Structures By Laser Sintering Of Nanoparticles, Vivekram Ramanathan

Masters Theses

"The focus of this study was to investigate an alternate microfabrication process of sintering nanoparticles using a patterned laser light to generate two dimensional (2D) and three dimensional (3D) geometries. With trends of producing electronic and medical devices using cheaper and faster technologies, a new procedure was developed to deposit and bond miniature patterns of silver nanoparticles onto silicon substrates.

The process consists of spraying silver nanoparticles onto the substrate while a patterned or modulated laser beam is focused onto the sprayed nanoparticles. These nanoparticles exposed under the modulated laser light undergo partial melting or sintering and adhere to the …

Quantification Of Product Color Preference In A Utility Function, Hannah L. Turner

Masters Theses

"Currently, many marketing and engineering tools exist to help a designer optimize quantitative attributes of a product, such as height, weight, volume, or cost. However, these methods cannot effectively take into consideration aesthetic attributes of a product, or any other attributes for which there is no understood functional relationship between the attribute's potential values and the consumer's preference. This research has begun the work of developing this necessary functional relationship for the aesthetic attribute of color and has created a methodology for further research. To do this, colors were represented by their red, green, and blue light components, and preference …