Mechanical Engineering Commons^™

H.F. Hauff Pruner Cutting Blades, Wyley Stewart

All Undergraduate Projects

Apple orchards are a critical component of agriculture in the United States, and keeping the apple trees in the best shape for optimum growth and production is hard work. Neil Hauff, an agriculture industry expert, challenged students at CWU to engineer a power assisted tree pruner. Across the country, apple orchards need pruned every season. The pruning of the trees is strenuous manual labor that requires many man hours. The proposed solution is to create a power assisted tree pruner that would minimize the amount of work needed to trim each tree branch. This project has been separated into three …

Enhancement Of Performance Of Micro Direct Ethanol Fuel Cells By Structural Modification, Sindhuja Valluri

Masters Theses

“Direct Ethanol Fuel Cells (DEFC’s) are becoming more important in current energy conversion devices because of their higher efficiency compared to other fuel cells. However, the performance of current DEFC’s is not efficient in providing energy to meet increasing energy demand. The objective of this work is to make the cell compact and at the same time improve performance. For this purpose, we have removed gasket and endplates to make structure compact and increased surface area by developing a new corrugated structure. This work also uses 3D printing technology Fused Deposition Modeling (FDM) to make pocket backing case to improve …

Stochastic Bi-Level Optimization Models For Efficient Operating Room Planning, Amin Abedini, Wei Li, Honghan Ye

Mechanical Engineering Faculty Publications

Within a hospital, the operating room (OR) department has the largest cost and revenue. Because of the aging population, the demand for surgical services has been increasing sharply in recent years. At the other hand, the rate of OR capacity expansion is lower than the rate of increasing demand. As a result, OR managers must leverage their resources by efficient OR planning. OR planning is challenging because of multiple competing\conflicting objectives such cost minimization and throughput maximization. Inherent uncertainty in the surgical procedures and patients arrivals complicate the decision making process. This increases the risk of non-realization of the system …

Damage Characterization Of Aircraft Fuselage Using Vibrothermography Technique-Review And Analysis, Abbasali Saboktakin

International Journal of Aviation, Aeronautics, and Aerospace

Vibrothermogrphy is a promising non-destructive technique that uses ultrasonic elastic waves to detect damages and is typically applied in the aerospace and automotive industries. This technique allows for defect selective imaging using thermal waves that are generated by ultrasound waves. In this paper, vibrothermography technique was applied to the aircraft fuselage to detect its damage. The influence of the damage on the temperature distribution at the damage region on the aluminum was investigated by finite element technique. Comprehensive understanding in edge crack in fuselage heating caused by local friction between crack surfaces was obtained.

Development Of Ceramic 3d Printer Using Cold-Based Extrusion, Noah Naden

Summer Community of Scholars Posters (RCEU and HCR Combined Programs)

No abstract provided.

Optimal Sintering Temperature Of Ceria-Doped Scandia Stabilized Zirconia For Use In Solid Oxide Fuel Cells, Amanda K. Assuncao

Honors Undergraduate Theses

Carbon emissions are known to cause decay of the Ozone layer in addition to creating pollutant, poisonous air. This has become a growing concern among scientists and engineers across the globe; if this issue is not addressed, it is likely that the Earth will suffer catastrophic consequences. One of the main culprits of these harmful carbon emissions is fuel combustion. Between vehicles, power plants, airplanes, and ships, the world consumes an extraordinary amount of oil and fuel which all contributes to the emissions problem. Therefore, it is crucial to develop alternative energy sources that minimize the impact on the environment. …

Regression Analysis Of Factors Impacting Problem Solving Engagement Within Lean Systems Implementation, David M. Parsley Ii

Theses and Dissertations--Mechanical and Aerospace Engineering

Organizations around the world have attempted to implement the concepts of the Toyota Production System (TPS), commonly referred to as Lean, with limited sustainable success. The central principles of TPS, continuous improvement and respect for people, are grounded in the Japanese values of Monozukuri and Hitozukuri. Monozukuri deals with creating or making a product, while Hitozukuri conveys the idea of developing people through learning. In order for organizations to adopt these values they must have a system that engages employees at all levels in applying problem solving to improve their work. This research uses organizational assessments obtained from a variety …

Bayesian-Integrated System Dynamics Modelling For Production Line Risk Assessment, Sudhir Punyamurthula

Theses and Dissertations--Mechanical and Aerospace Engineering

Companies, across the globe are concerned with risks that impair their ability to produce quality products at a low cost and deliver them to customers on time. Risk assessment, comprising of both external and internal elements, prepares companies to identify and manage the risks affecting them. Although both external/supply chain and internal/production line risk assessments are necessary, internal risk assessment is often ignored. Internal risk assessment helps companies recognize vulnerable sections of production operations and provide opportunities for risk mitigation.

In this research, a novel production line risk assessment methodology is proposed. Traditional simulation techniques fail to capture the complex …

The Kentucky Re-Entry Universal Payload System (Krups): Sub-Orbital Flights, James Devin Sparks

Theses and Dissertations--Mechanical and Aerospace Engineering

The Kentucky Re-entry Universal Payload System (KRUPS) is an adaptable testbed for atmosphere entry science experiments, with an initial application to thermal protection systems (TPS). Because of the uniqueness of atmospheric entry conditions that ground testing is unable to replicate, scientists principally rely on numerical models for predicting entry conditions. The KRUPS spacecraft, developed at the University of Kentucky, provides an inexpensive means of obtaining validation data to verify and improve these models.

To increase the technology readiness level (TRL) of the spacecraft, two sub-orbital missions were developed. The first mission, KUDOS, launched August 13th, 2017 on a Terrier-Improved Malamute …

Sustainable Living Factories For Next Generation Manufacturing, Yoram Koren, Xi Gu, Fazleena Badurdeen, Ibrahim S. Jawahir

Mechanical Engineering Faculty Publications

To be profitable and to generate sustainable value for all stakeholders, next generation manufacturers must develop capabilities to rapidly and economically respond to changing market needs while at the same time minimizing adverse impacts on the environment and benefiting society. 6R-based (Reduce, Reuse, Recycle, Recover, Redesign and Remanufacturing) sustainable manufacturing practices enable closed-loop and multi-life cycle material flow; they facilitate producing more sustainable products using manufacturing processes and systems that are more sustainable. Reconfigurable Manufacturing Systems (RMS) and its characteristics of scalability, convertibility, diagnosability, customization, modularity and integrability have emerged as a basis for living factories for next generation manufacturing …

Towards Developing Sustainable Reconfigurable Manufacturing Systems, Aihua Huang, Fazleena Badurdeen, Ibrahim S. Jawahir

Mechanical Engineering Faculty Publications

This paper aims to examine the sustainable manufacturing performance of Reconfigurable Manufacturing Systems (RMSs) using existing sustainable manufacturing metrics. RMS has six key characteristics including modularity, integrability, customization, scalability, convertibility, and diagnosability. In this paper, ‘convertibility’ is quantified by considering configuration convertibility, machine convertibility, and material handling device convertibility from the RMS perspective. In addition, the performance of RMSs with different convertibility levels is also evaluated by using sustainable manufacturing metrics. A numerical example is used to demonstrate the computational approach. Results of the analysis are used to show how sustainable manufacturing performance of RMS changes as system convertibility varies. …

Advanced Process To Embed Optical Fiber Sensors Into Casting Mold For Smart Manufacturing, Raghavender Reddy Jakka

Masters Theses

"Optical fiber sensors embedded in metals with distributed sensing can sense temperature at multiple points with single fiber. This is useful for smart manufacturing like structural health monitoring in aerospace industry and smart molds in manufacturing plants. There is a huge difference in thermal coefficient of expansion for fiber and metal. This is the reason for the increase in sensitivity for embedded fiber sensors. However, at high temperatures, the stress on the fiber increases, eventually damaging the sensor. The fiber-metal interface determines the sensor performance. A tight interface results in high sensitivity and a gap in the interface enhances sensing …

Laser-Aided Additive Manufacturing Of Glass, John Michael Hostetler

Masters Theses

“This thesis presents various approaches for the laser-aided additive manufacturing of glass. First, a technique is investigated to create free-form, low to zero coefficient of thermal expansion structures out of silica-gel. A CO₂ laser was coupled through a gantry system and focused onto a binder-free silica-gel powder bed (15-40 μm particles). Prior to writing each layer, powder is dispensed by sifting it onto the build platform as opposed to a conventional wiper system, avoiding contacting and potentially damaging sensitive parts. After deposition, the parts are annealed in a furnace to increase their strength. The influence of various process parameters …

Investigation Of The Information Provided By Light Touch For Balance Improvement In Humans, Anirudh Saini

Masters Theses

"This study investigates the information provided by Light Touch (LT) in improving human postural stability without mechanical assistance. Light Touch, an interaction force with a magnitude about 1 N, is known to improve postural stability in humans during quiet standing. However, the nature of the information from LT that helped improve balance is yet unknown. In this work, we hypothesized that LT provides information about one's body kinematics. We used a haptic robot to provide modulated, measurable light interaction force on the high back haptic location of humans to provide body kinematics-dependent information through LT. Standing balance experiments were performed …

Inspection Process Flow Development For A Warehouse, Pahalawaththage Perera

All Graduate Theses, Dissertations, and Other Capstone Projects

The project is based on a medical device outsourcing company in the US. In 2018 the company added a 44,000 sq ft new warehouse. With the scales of growth and market competition, it has come to a need to optimize production capacity to achieve 98% monthly on time delivery target. Optimizing production capacity comes with efficiently managing operations that impact overall product lead time. A primary factor that impacts the overall product lead time is production preparation time. Production preparation time is impacted by lead times of 3 operations managed by the new warehouse - Receiving Inspection, Incoming Inspection, and …

Battery Test Chamber, Olivia Cole, Noah Purdy, Jacob Happ

Williams Honors College, Honors Research Projects

A battery test chamber was designed for temperature-controlled experiments on batteries. The apparatus is a standalone desktop unit capable of testing a battery of maximum size 2.25” x 2.25” x 2”. There are two separate chambers divided by a rotating, 90° door. The chamber halves are used for heating and cooling the battery, respectively. An adjustable mount for the battery allows for variation in sample size and securely holds the battery throughout the experiment. The operator can twist a knob on top of the box to spin the battery between the hot and cold chambers. The hot side is equipped …

Guardian Condor, Kevin Bayonnet

Williams Honors College, Honors Research Projects

Our group has teamed up with Dr. Williams from Discovery Lab Global to research the capabilities of 3D printed Unmanned Aerial Vehicles (UAVs). The goal of our project is to deliver a 3D printed glider prototype which can later be fitted with electronics for controlled flight. The glider must also carry a payload of 2 to 3 pounds in addition to the electronics. These requirements must be met all while using a basic 3D printer with low cost plastic

Throughout the Fall 2017 semester, our group made a significant amount of progress by completing the conceptual design portion of the …

Human Powered Vehicle Design Team: Speed Variable Steering Stabilizer, Eric Miller, Matt Kraml

Williams Honors College, Honors Research Projects

The Human Powered Vehicle Competition (HPVC) is held annually by ASME at a few locations. The University of Akron has competed in the ASME-East and ASME-West competitions over the past handful of years against universities from all over the world. Objectives of each team for the competition are three-fold: vehicle design, racing performance, and innovation. Our senior design project involved working on the innovation concept for ASME-East 2018 held at Penn State University during the weekend of 4/13. Speed variable steering was decided upon by the entire HPVC team early in the design process as the innovation choice for this …

Indicator-Supporting Fixture Based On A Time And Motion Study, James Anthony

Williams Honors College, Honors Research Projects

The design goal of this project was proposed by the sponsor company, Jay-Em Aerospace in Cuyahoga Falls, Ohio. I was tasked with observing a process carried out in the Assembly department by multiple people and charged with coming up with a fixture to improve safety, speed, and accuracy of this task. To determine how to make the process safer, interviews were conducted with the people who would usually be carrying out this process and determined their top concerns and issues with how it is carried out currently. To improve the speed and accuracy of the process, a "time and motion …

Human Powered Vehicle Frame Design, Analysis, Manufacturing, And Testing, Christopher Reed, Kole W. Williams

Williams Honors College, Honors Research Projects

The University of Akron Human Powered Vehicle Design Team began this academic year with a mission to create a practical, lightweight, safe, and efficient human powered vehicle. The main objectives of ZC18 were inspired by competition in the 2018 Human Powered Vehicle Challenge at ASME E-Fest East. In addition to adhering to the rules of this competition, scoring high on the submitted reports, and competing well in the racing events, the team set a goal to assist in furthering knowledge related to the topic of human powered vehicles.

ZC18 was constructed nearly completely in the University of Akron’s Design Center …

Swagelok Adjustable Check Valve Setting Device, Brandon Sours, Paul Olson, David Race, Nick Rimpf

Williams Honors College, Honors Research Projects

Check valves are used to control the amount of flow through a valve and only open when a certain pressure is reached. The path of the fluid is strictly in one direction, which allows the valve to prevent any back flow within a system. They are also one of few self-automated piping system components that do not require assistance to open or close. Some check valves use a combination spring-and-nut compression assembly to set an opening pressure. As the nut is used to set the spring compression, and by extension the opening pressure, problems tend to arise when adjusting the …

Mht Assembly Line, Sean Lundholm

Williams Honors College, Honors Research Projects

The purpose of this report is to record the process followed and steps taken to design and implement a new product assembly line. While the implementation of the line required more than what is in this report, the projects outlined are those I was personally involved in and responsible for. This report will outline why the project was required, the steps taken to complete the project, and the challenges faced. Throughout the progression of the project, many different parts and areas were considered. As each of these was brought into focus, new challenges presented themselves and were dealt with accordingly. …

Consuming Digital Debris In The Plasticene, Stephen R. Parks

Theses and Dissertations

Claims of customization and control by socio-technical industries are altering the role of consumer and producer. These narratives are often misleading attempts to engage consumers with new forms of technology. By addressing capitalist intent, material, and the reproduction limits of 3-D printed objects’, I observe the aspirational promise of becoming a producer of my own belongings through new networks of production. I am interested in gaining a better understanding of the data consumed that perpetuates hyper-consumptive tendencies for new technological apparatuses. My role as a designer focuses on the resolution of not only the surface of the object through 3-D …

Task Complexity, And Operators’ Capabilities As Predictor Of Human Error: Modeling Framework And An Example Of Application, Maria Chiara Leva, Alberto Caimo, Rebecca Duane, Micaela Demichela, Lorenzo Comberti

Conference Papers

This paper presents the initial framework adopted to assess human error in assembly tasks at a large manufacturing company in Ireland. The model to characterize and predict human error presented in this paper is linked conceptually to the model introduced by Rasch (1980), where the probability of a specified outcome is modelled as a logistic function of the difference between the person capacity and item difficulty. The model needs to be modified to take into account an outcome that is not dichotomous and feed into the interaction between two macro factors: (a) Task complexity: that sum-marises all factors contributing to …

Capillary-Assisted Enhanced Condensation Heat Transfer For Low Surface Tension Liquids, Gnana Vishnu Durgam

Dissertations, Master's Theses and Master's Reports

Extensive research has been carried out over the course of the last few decades to induce dropwise condensation as it offers 5 - 7 times better heat transfer performance compared to filmwise condensation process. A number of methods such as low surface energy hydrophobic coatings, surface modification of hydrophobic surfaces to fabricate micro, nano and hierarchical structures, and the recent incorporation of jumping droplet phenomenon have provided effective means to further enhance the condensation heat transfer. However, existing methods to enhance condensation heat transfer rate fail in the case of low surface tension, highly wetting liquids such as hydrocarbons, cryogens, …

Investigation Of 2195 And 2219 Post Weld Heat Treatments For Additive Friction Stir Lap Welds, Matthew Champagne

LSU New Orleans Theses and Dissertations

To evaluate potential uses for friction stir welding in additive manufacturing, two separate parts were fabricated, one of 2195-T84 and the other 2219-T87, utilizing fixed pin techniques and additive lap welds. The parts were cut into samples, artificially aged and subjected to Rockwell hardness (HRB), Vickers hardness, micrographic photography, and metallographic imaging on both pre- and post- heat treatment. Additionally, tensile testing was performed on the heat-treated samples. A comparisons of test results showed a minimal increase in the yield strength of the 2195-T84 samples compared to as-welded tensile results obtained from a previous project. The ultimate tensile strength was …

The Vibe, Sarah P. Douglass

Capstones

The Vibe is a long-form narrative about where tech is taking the female orgasm. The piece concludes that physiological research is a required next step when creating the climax of the future.

http://sarahpdouglass.com

A Framework Towards Technology Creation In Africa: Focusing On Ghana, Martin Yao Donani, Hannatu Abue Kugblenu, Azindow Bawa Fuseini

International Journal of African Development

Underdevelopment in Africa has been historical and a global concern coupled with the quest for good governance. Several efforts have been made in academia, national governments, the international community, and other institutional arrangements to reverse the trend. These efforts however are yet to produce a lasting result as Africa is still characterized by low productivity output, poverty and a widening technology gap when compared to other developing regions of the world. Conventional approaches used to address the African problem have consistently been devoid of indigenous technology development. Technology is here seen as paramount to every form of production on which …

Usa Boccia Ball Ramp For Athletes With Quadriplegia, Alissa A. Koukourikos, Matthew Lee, Nathan Bernards

Mechanical Engineering

In this report, the design process in creating an assistive device for Boccia Classification 3 (BC3) players is outlined. The initial research steps, including research into the rules of the game, capabilities of the players, and existing products is documented to show where ideas for the product stemmed from. This transitions into requirements that the sponsor requested, and preliminary designs and ideas for the product. Finally, this report explains the details of the final design, which has been analyzed for safety, ease of use, and ability to function under different conditions. The processes of manufacturing and testing will also be …

Real Time And High Fidelity Quadcopter Tracking System, Tyler Mckay Hall

Computer Engineering

This project was conceived as a desired to have an affordable, flexible and physically compact tracking system for high accuracy spatial and orientation tracking. Specifically, this implementation is focused on providing a low cost motion capture system for future research. It is a tool to enable the further creation of systems that would require the use of accurate placement of landing pads, payload acquires and delivery. This system will provide the quadcopter platform a coordinate system that can be used in addition to GPS.

Field research with quadcopter manufacturers, photographers, agriculture and research organizations were contact and interviewed for information …