Mechanical Engineering Commons^™

Natural Convection From Circular Cylinders, Sandra K. S. Boetcher

Publications

Chapter 1

Natural convection heat transfer from circular cylinders in quiescent environments is a subject which has been studied extensively. Although a well-established topic, to the best knowledge of the author no single source of reference is found for natural convection from circular cylinders for varying orientations (horizontal, vertical, and inclined). This book attempts to be a reference for Nusselt number correlations for circular cylinders of all inclinations including horizontal and vertical.

Thermal Properties Of Soft Nanomaterials: Materials Synthesis And Fabrication, Meng Pan, Collier Miers, Amy Marconnet, Yu Han

The Summer Undergraduate Research Fellowship (SURF) Symposium

The properties of soft nanomaterials are hard to measure exactly due to their mechanical properties and unstable shape. In particular, hydrogels are a class of cross-linked polymers that can absorb large quantities of water changing their shape under the influence of various conditions such as humidity, temperature, and pH. This research addresses the fabrication of a material that has a significant contrast in properties under different conditions (e.g. temperature, wetting, and pH) and determine the physical mechanisms of heat transfer in this nanomaterial. The hydrogels are made using a several cycles of a freeze-thaw method. The method requires soluble material. …

Radiation Measurements And Data Analysis Of Turbulent Premixed Lean Flame, Yunzhe Yang, Dong Han, Jay P. Gore

The Summer Undergraduate Research Fellowship (SURF) Symposium

An accurate understanding of the radiation transfer in turbulent premixed lean flame is critical for improving energy efficiencies and reducing emissions such as nitric oxide and soot. Radiation measurement is an effective and nonintrusive way to study the radiation properties of turbulent premixed lean flames. In this study, a high-speed infrared camera was utilized to measure the planar radiation from turbulent premixed lean flames under different conditions. Time-dependent flame images were acquired and radiation statistics were calculated and compared to investigate the effects of equivalence ratio, heat release rate, hydrogen pilot flame rate, and co-flow rate on the radiation intensity …

The Role Of Surface Area In Catalytic Gasification Of Biomass, Elizabeth A. Wachs, Nitish Kumar, Indraneel Sircar, Prithviraja Basak, Jay P. Gore Phd

The Summer Undergraduate Research Fellowship (SURF) Symposium

Gasification of biomass has the potential to provide a carbon-negative source of liquid fuels. The current limited use of gasification is due in part to the high temperatures necessary to achieve high conversion levels. These temperatures can be lowered by the use of catalysts, but the mechanisms by which catalysts affect the reaction rate are not fully understood. Here, the structural component of potassium carbonate’s role in the gasification process was examined. Samples of pinewood sawdust were impregnated with potassium carbonate, then pyrolyzed with N2 in a fixed bed reactor at 750°C (heater thermocouple reading). Half of the char was …

Preliminary Testing Of Plasma-Induced Combustion, Ahmed Thalib Razi, Carson Slabaugh, Robert Lucht

The Summer Undergraduate Research Fellowship (SURF) Symposium

Plasma-induced combustion (PIC) has been shown to improve the reliability, efficiency, and delay time of ignition in flight systems like augmentors and scramjets. These high-velocity systems are mostly used in military applications, and improvement may help commercial viability. To understand this chemical process, the concentration of radicals, particularly H radicals, must be tracked through the flame using laser diagnostics. This requires a steady source of plasma-assisted combustion to be secured and well-understood. A plasma torch flowing partially premixed air and methane was installed and successfully operated, and preliminary testing was carried out. Primarily it was observed that PIC created stable …

Thermal Properties Of Soft Nanomaterials: Thermal Measurement Design, Yu Han, Meng Pan, Amy Marconnet, Collier Miers

The Summer Undergraduate Research Fellowship (SURF) Symposium

Soft materials like hydrogels have multiple tunable material properties because of their unique structures. Due to the ability to respond to stimuli like temperature or chemical environment, they have numerous applications in different fields like delivering drugs inside the human body and other medical uses. Details of the thermal transport mechanisms, as well as the overall thermal properties, are critical for a variety of applications. Multi-property measurements elucidate the underlying transport mechanisms in the soft materials. This research demonstrates a new methodology of measuring thermal properties of soft materials. This work uses the 3w method [1,2] for measuring the thermal …

Minimization Of The Effects Of Secondary Reactions On Turbine Film Cooling In A Fuel Rich Environment, Andrew T. Shewhart

Theses and Dissertations

The demand for increased thrust, higher engine efficiency, and reduced fuel consumption has increased the turbine inlet temperature and pressure in modern gas turbine engines. The outcome of these higher temperatures and pressures is the potential for unconsumed radical species to enter the turbine. Because modern cooling schemes for turbine blades involve injecting cool, oxygen rich air adjacent to the surface, the potential for reaction with radicals in the mainstream flow and augmented heat transfer to the blade arises. This study evaluated various configurations of multiple cylindrical rows of cooling holes in terms of both heat release and effective downstream …

Formula Sae Cooling System Design, Lisa Van Den Berg, Brandon Lofaro

Mechanical Engineering

The overall objective of this senior project is to develop, via testing and analysis, a guided process that will aid the Cal Poly Formula SAE team in designing their cooling system. More specifically, a set of designed tests will yield the results necessary in determining a combination of fan and radiator that will achieve appropriate cooling.

A test section that has the capability of interfacing with both the wind tunnel in the Thermal Science Lab and a radiator will be used to facilitate the necessary experiments. The wind tunnel is powered by fan controlled by a variable frequency drive that …

Economic, Energy And Ghg Emissions Performance Evaluation Of A Whispergen Mk Iv Stirling Engine Μ-Chp Unit In A Domestic Dwelling, Gerry Conroy, Aidan Duffy, Lacour Ayompe

Articles

This paper presents an assessment of the energy, economic and greenhouse gas emissions performances of a WhisperGen Mk IV Stirling engine μ-CHP unit for use in a conventional house in the Republic of Ireland. The energy performance data used in this study was obtained from a field trial carried out in Belfast, Northern Ireland during the period June 2004 - July 2005 by Northern Ireland Electricity and Phoenix Gas working in collaboration with Whispertech UK. A comparative performance analysis between the µ-CHP unit and a condensing gas boiler revealed that the µ-CHP unit resulted in an annual cost saving of …

Investigation Of Boiling Performance Of Graphene-Coated Surfaces, Daniel C. Stack

Renée Crown University Honors Thesis Projects - All

In this Capstone Project, I sought to investigate the boiling performance of graphene-coated surfaces. Boiling was accomplished in a pool boiling chamber, with samples of graphene-coating SiO₂ wafers. I developed a procedure for graphene transfer for sample fabrication. Samples were prepared with graphene grown on copper substrates by chemical vapor deposition (CVD). Graphene was transferred from copper substrates to SiO­₂ wafers by a thermal release transfer tape. Copper was etched away from the tape-graphene combination by ferric chloride, and the tape was peeled away after heating, leaving graphene on the SiO₂ substrate. Contact angles were measured to …

High Temperature Ltcc Based Sic Double-Sided Cooling Power Electronic Module, Hao Zhang

Graduate Theses and Dissertations

This objective of this dissertation research is to investigate a module packaging technology for high temperature double-sided cooling power electronic module application. A high-temperature wire-bondless low-temperature co-fired ceramic (LTCC) based double-sided cooling power electronic module was designed, simulated and fabricated. In this module, the conventional copper base plate is removed to reduce the thermal resistance between the device junctions to the heat sink and to improve the reliability of the module by eliminating the large area solder joint between the power substrate and the copper base plate. A low-temperature co-fired ceramic (LTCC) substrate with cavities and vias is used as …

Simulation Of An Intake Manifold Pre-Heater For Cold Diesel Engine Startup, Patrick K. Kreun

Masters Theses

Ensuring consistent, reliable diesel engine startups in cold temperatures is of utmost importance in a number of applications. Under extreme temperatures, the use of glow plugs is complemented by intake manifold heaters. In these, the energy released from combustion increases the intake air temperature before the air enters the main combustion chamber. Since the process also alters the stoichiometry of the fuel-air mixture at the intake ports, the preheater operation must be optimized in order to guarantee successful and reliable in-cylinder combustion during engine startups. This paper describes the development of an intake manifold model incorporating an air pre-heater for …

Analytical Performance Evaluation Of Thermoelectric Modules Using Effective Material Properties, Sean Lwe Leslie Weera

Masters Theses

Designers often face the predicament of non-standardized forms of performance data provided by thermoelectric module manufacturers. Other than experimental means the only method to evaluate the performance of a product would be through analytical modeling using material properties that are usually undisclosed and unknown. This work studies the theoretical approach of obtaining such material properties using the maximum operating parameters reported by the manufacturers. These values are then analytically employed to evaluate the performances of these thermoelectric modules. Experimental means are also devised and carried out on these test samples to validate the integrity of the results. Three-way comparisons between …

Operational Characteristics Of An Ultra Compact Combustor, Christopher J. Damele

Theses and Dissertations

Ultra Compact Combustors offer unique solutions to minimize engine size and weight. They accomplish this by reducing the number of components in the engine core and perform the combustion in a circumferential cavity that encircles the core flow. Within this cavity, the fuel is injected rich. Burning continues to occur in the vane passage beneath the circumferential cavity which must be completed in a controlled manner prior to the inlet plane of the turbine rotor. Furthermore, the temperature distribution at the exit of the vane passage must be controlled to generate high work extraction from the turbine. The primary metrics …

High-Efficiency Thermodynamic Power Cycles For Concentrated Solar Power Systems, Marc T. Dunham, Brian Iverson

Faculty Publications

This paper provides a review of high-efficiency thermodynamic cycles and their applicability to concentrating solar power systems, primarily focusing on high-efficiency single and combined cycles. Novel approaches to power generation proposed in the literature are also highlighted. The review is followed by analyses of promising candidates, including regenerated He-Brayton, regenerated CO2-Brayton, CO2 recompression Brayton, steam Rankine, and CO2-ORC combined cycle. Steam Rankine is shown to offer higher thermal efficiencies at temperatures up to about 600 ˚C but requires a change in materials for components above this temperature. Above this temperature, CO2 recompression Brayton cycles are shown to have very high …

Thermal Conductivity Of Alumina And Silica Nanofluids, Julian Bernal Castellanos

All Graduate Theses, Dissertations, and Other Capstone Projects

This thesis studies the effects of the base fluid, particle type/size, and volumetric concentration on the thermal conductivity of Alumina and Silica nanofluids. The effects of base fluid were observed by preparing samples using ethylene glycol (EG), water, and mixtures of EG/water as the base fluid and Al2O3 (10 nm) nanoparticles. The particles type/size and volumetric concentration effects were tested by preparing samples of nanofluids using Al2O3 (10nm), Al2O3 (150nm), SiO2 (15 nm), and SiO2 (80 nm) nanoparticles and ionized water as base fluid at different volumetric concentrations. All samples were mixed using a sonicator for 30 minutes and a …

Theoretical Study Of Thermal Analysis Kinetics, Yunqing Han

Theses and Dissertations--Mechanical and Aerospace Engineering

In the past decades, a great variety of model fitting and model free (isoconversional) methods have been developed for extracting kinetic parameters for solid state reactions from thermally stimulated experimental data (TGA, DSC, DTA etc.). However, these methods have met with significant controversies about their methodologies. Firstly, model-fitting methods have been strongly criticized because almost any reaction mechanism can be used to fit the experimental data satisfactorily with drastic variations of the kinetic parameters, and no good criterion exists to tell which mechanism is the best choice. Secondly, previous model free methods originated from the isoconversional principle, which is often …

A Metrics-Based Sustainability Assessment Of Cryogenic Machining Using Modeling And Optimization Of Process Performance, Tao Lu

Theses and Dissertations--Mechanical and Aerospace Engineering

The development of a sustainable manufacturing process requires a comprehensive evaluation method and fundamental understanding of the processes. Coolant application is a critical sustainability concern in the widely used machining process. Cryogenic machining is considered a candidate for sustainable coolant application. However, the lack of comprehensive evaluation methods leaves significant uncertainties about the overall sustainability performance of cryogenic machining. Also, the lack of practical application guidelines based on scientific understanding of the heat transfer mechanism in cryogenic machining limits the process optimization from achieving the most sustainable performance.

In this dissertation, based on a proposed Process Sustainability Index (ProcSI …

Multidimensional Modeling Of Pyrolysis Gas Transport Inside Orthotropic Charring Ablators, Haoyue Weng

Theses and Dissertations--Mechanical and Aerospace Engineering

During hypersonic atmospheric entry, spacecraft are exposed to enormous aerodynamic heat. To prevent the payload from overheating, charring ablative materials are favored to be applied as the heat shield at the exposing surface of the vehicle. Accurate modeling not only prevents mission failures, but also helps reduce cost. Existing models were mostly limited to one-dimensional and discrepancies were shown against measured experiments and flight-data. To help improve the models and analyze the charring ablation problems, a multidimensional material response module is developed, based on a finite volume method framework. The developed computer program is verified through a series of test-cases, …

Heat Transfer Characteristics In Wildland Fuelbeds, Justin English

Theses and Dissertations--Mechanical and Aerospace Engineering

The fundamental physics governing wildland fire spread are still largely misunderstood. This thesis was motivated by the need to better understand the role of radiative and convective heat transfer in the ignition and spread of wildland fires. The focus of this work incorporated the use of infrared thermographic imaging techniques to investigate fuel particle response from three different heating sources: convective dominated heating from an air torch, radiative dominated heating from a crib fire, and an advancing flame front in a laboratory wind tunnel test. The series of experiments demonstrated the uniqueness and valuable characteristics of infrared thermography to reveal …

Pitting Corrosion And Corrosion Fatigue Crack Growth Behavior Of Oil-Grade Alloy 718 In Sodium Chloride Solution, Ting Chen

Graduate Theses, Dissertations, and Problem Reports (ETD)

Oil-grade nickel-base alloy 718 has been recently used in the oil and gas industry for downhole drilling components especially for the parts of the bottom hole assembly (BHA) due to its superior mechanical properties, good corrosion resistance, non-magnetic properties and ability to be heat treated to various strength levels. As the modern oil and gas industry explored into coastal and marine locations, deeper and deeper wells have been drilled with high pressure high temperature, making the demand for increased strength and good toughness super critical for alloys used in ultra-deep wells drilling. Moreover, the existence of high concentrations of chloride …

Experimental Investigation Of Mist Film Cooling And Feasibility Study Of Mist Transport In Gas Turbines, Reda M. Ragab

LSU New Orleans Theses and Dissertations

In the modern advanced gas turbines, the turbine inlet temperature may exceed 1500°C as a requirement to increase power output and thermal efficiency. Therefore, it is imperative that the blades and vanes are cooled so they can withstand these extreme temperatures. Film cooling is a cooling technique widely used in high-performance gas turbines. However, the film cooling effectiveness has almost reached plateau, resulting in a bottleneck for continuous improvement of gas turbines' efficiency.

In this study, an innovative cooling scheme, mist film cooling is investigated through experiments. A small amount of tiny water droplets with an average diameter about 10-15 …

A Study On The Integration Of A Novel Absorption Chiller Into A Microscale Combined Cooling, Heating, And Power (Micro-Cchp) System, Scott J. Richard

LSU New Orleans Theses and Dissertations

This study explores the application of micro-CCHP systems that utilize a 30 kW gas microturbine and an absorption chiller. Engineering Equation Solver (EES) is used to model a novel single-effect and double-effect water-lithium bromide absorption chiller that integrates the heat recovery unit and cooling tower of a conventional CCHP system into the chiller’s design, reducing the cost and footprint of the system. The results of the EES model are used to perform heat and material balances for the micro-CCHP systems employing the novel integrated chillers, and energy budgets for these systems are developed. While the thermal performance of existing CCHP …

A Numerical Study Of High Temperature And High Velocity Gaseous Hydrogen Flow In A Cooling Channel Of A Ntr Core, Sajan B. Singh

LSU New Orleans Theses and Dissertations

Two mathematical models (a one and a three-dimensional) were adopted to study, numerically, the thermal hydrodynamic behavior of flow inside a single cooling channel of a Nuclear Thermal Rocket (NTR) engine. The first model assumes the flow in the cooling channel to be one-dimensional, unsteady, compressible, turbulent, and subsonic. The working fluid (GH₂) is assumed to be compressible. The governing equations of the 1-D model are discretized using a second order accurate finite difference scheme. Also, a commercial CFD code is used to study the same problem. Numerical experiments, using both codes, simulated the flow and heat transfer …

Sodhana Environmental - Final Design Report, Eric Taylor, Corissa Bellis, Cody Perez, Cameron Zeller

Mechanical Engineering

A fully designed cost-effective, sustainable, toilet for the developing world.

Heat Transfer Experiment: Energy Conservation, Ben Ward, Brett Wallace, Ryan Waltman

Mechanical Engineering

This proposal, prepared for the Mechanical Engineering Department by the HTEC design team will redesign and replace the current energy conversion lab that is inaccurate and out of date. The team will evaluate methods of energy conversion, specifically using braking systems, as well as existing labs in order to design an accurate and relatable experiment for this lab. The project team will work with Professor Kim Shollenberger in order to design an experiment that demonstrates energy conversion through the first law of thermodynamics while utilizing a common device that is practical in student’s lives. The final result of this project …

Investigation Of Thermal Cycle And Hardness Distribution In The Laser Cladding Of Aisi H13 Tool Steel Produced By A High Power Direct Diode Laser, Parisa Farahmand, Prabu Balu, Fanrong Kong, Radovan Kovacevic

Mechanical Engineering Research

Laser cladding (LC) of tool steel has significant application in rapid tooling, and surface coating for worn-out components in different industries. During the LC process, several phase transformations influence the microstructural and mechanical properties of the deposited layer. In order to successfully implement the LC process, it is essential to understand the relationship between the thermal cycle (heating and cooling), phase transformations, and the output quantities of the deposited layer. In this study a direct diode laser with a power of up to 8 kW was used to deposit AISI H13 tool steel on mild steel grade A36 substrate to …

Radiation Intensity Of A Turbulent Sooting Ethylene Flame, Ryan M. Hartman, Jay P. Gore

The Summer Undergraduate Research Fellowship (SURF) Symposium

Turbulent sooting flame radiation is relevant to applications ranging from fire safety to gas turbine engines. The complex direct interactions of soot and radiation intensity are of particular importance when creating accurate soot prediction models. Previous studies have measured gas-band and broadband radiation intensity from turbulent sooting flames. The focus of the current study is the characterization of radiation intensity emanating from soot. A high-speed infrared camera (FLIR Phoenix) was used to acquire time-dependent quantitative images of radiation intensity of a turbulent sooting ethylene flame. The flame had a Reynolds number of 15,200 and was stabilized on a burner with …

Advanced Visualization Techniques Of Hot-Jet Combustion Of Lean And Ultra-Lean Substances, Timothy I. Machin, Li Qiao

The Summer Undergraduate Research Fellowship (SURF) Symposium

Research has been conducted on ignition of natural gas as a potential replacement for fossil fuels. A reason natural gas is not widely used and adapted is because of the harmful emissions created when combusted in rich mixtures, but if the gas can be burned at a lean or ultra-lean equivalence ratio, these emissions can be reduced or even eliminated. One method of burning lean and ultra-lean substances is by use of hot-jet ignition. This method ignites the substance near its combustion temperature, reducing the harmful emissions. This method is not yet fully understood, and so research must be done …

Experimental Study Of Co2 Recycling Using Metal-Oxide Enhanced Coconut Char Gasification: Catalytic Effect Of Potassium Carbonate On Gasification, Mengqi Gao, Indraneel Sircar, Jay P. Gore

The Summer Undergraduate Research Fellowship (SURF) Symposium

Biomass gasification is an important process in the production of bio-derived fuels and renewable energy. Biomass gasification with CO₂ is an endothermic process requiring high temperatures, resulting in low process-efficiency. Metals found in the ash in biomass feedstock have shown rate-promoting effects on the C-CO₂ reaction and have motivated the study of low-temperature catalytic gasification. The present study investigates the catalytic effects of potassium (K) on the biomass gasification reactivity of a coconut-derived char (>99.9% carbon) within the temperature range of 600 – 1000 ^oC. A wet-impregnation technique is used to prepare K-treated chars. Gasification of …