Mechanical Engineering Commons^™

Research Of Energy Indicators Of Electric Drives With Frequency Converters (Frequency Converters) On The Operating Equipment Of Cotton Cleaning Plants, A.J. Isakov, B.K. Tukhtamishev, J.N. Tolipov

Irrigation and Melioration

The article deals with the theoretical and practical substantiation of the replacement of an unregulated electric drive of the main technological equipment of cotton refineries with a frequency-controlled electric drive. The influence of a change in the load on the motor shaft on the main parameters of the steady state is considered. In an asynchronous motor, with an increase in the load, slip increases to such a value at which the torque of the motor balances the increased moment of resistance. Considering that when the stator slip resistance is less than the critical one is a small fraction of the …

Stabilization Of Discharge Processes Involved In Electrical Fields Of Electrostatic Precipitators, Sh.M. Muzafarov, B.N. Erkinov, A.I. Pardaev, V.E. Baliskiy, B.К. Tаgaev

Irrigation and Melioration

The article provides information on achievements in the field of electrical gas cleaning. A critical analysis of the principle of operation of the electrostatic precipitators developed and currently in operation is carried out. The possibility of increasing the efficiency of electrical gas cleaning using unipolar voltage pulses is analyzed. A theoretical analysis of the processes in the discharge gap was carried out using the existing theory of electric discharges in gases. Based on the analysis of the data, the discharge mechanism is established in a sharply inhomogeneous electric field at a pulsed voltage. It is established that when using voltage …

Determination Of The Rational Values Of The Parameters Of The Disc Rollers Of The Combined Unit, A.K. Igamberdiev, D.K. Muqimova

Irrigation and Melioration

In our country, repeated crops are sown in newly plowed lands. In such conditions, the use of combined units that perform several technological operations simultaneously in one pass is considered effective. However, due to the inadequacy and validity of the parameters of the working bodies for the quality of pre-sowing tillage in newly plowed lands, there is an increase in the number of passes, fuel consumption, loss of soil moisture and other costs and, as a result, the possibility of timely sowing and friendly germination of repeated crops is reduced . The rational parameters of the new design of disk …

Autonomous Photovoltaic System For Year-Round Guarantee Supply Of Electricity To Rural Facilities, M.N. Tursunov, Х. Sabirov, U.R. Kholov, Т.Z. Аkhtamov

Irrigation and Melioration

The article discusses the physical and technical features of the experimental results of studying the parameters of an autonomous photovoltaic station (AFES) with a power of 2600 W designed and manufactured on the basis of 16 photovoltaic batteries made of polycrystalline silicon with an efficiency of 15.6 %. It is shown that an autonomous photovoltaic efficiently and reliably provides electric energy a lighting system for car parking in the winter season (January and February) and it is planned to lift water from a well with a depth of 70-80 m for irrigation and maintenance of the Heliopoligon from April 2020. …

Preparation Characterization And Tribological Behavior Of Lube Oil With Nanoparticles Additives, Waleed Alghani

Student Works (2020-2029)

There are many companies worldwide that would like to improve and upgrade the lube oil and enhance its performance. There is a big concern for the enhancement of lube oil by using nanotechnology and more precisely with using nanomaterial additives. Much work has made to explore and develop new sorts of lubricating oil nano-additives to diminish wear and friction in tribological configurations and to enhance surface morphology. It has noted that the use of dual nano-additives should examine the lubricating capacity and durability of lubricant. (TiO2 Anatase + Graphene) and (ZnO + Graphene) nanoparticles have selected to formulate nano-additives that …

An Affordable And Portable Palpable System For Sensing Breast Tissue Abnormalities, Cody J. Clarke

Montview Journal of Research & Scholarship

Due to the high cost of equipment and lack of trained personnel, manual palpation is a preferred alternative breast examination technique over mammography. The process involves a thorough search pattern using trained fingers and applying adequate pressure, with the objective of identifying solid masses from the surrounding breast tissue. However, palpation requires skills that must be obtained through adequate training in order to ensure proper diagnosis. Consequently, palpation performance and reporting techniques have been inconsistent. Automating the palpation technique would optimize the performance of self-breast examination, optimize clinical breast examinations (CBE), and enable the visualization of breast abnormalities as well …

Me-Em 2019-20 Annual Report, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering Annual Reports

Table of Contents

• Element 1
• Element 2
• Element 3
• Element 4
• Enrollment & Degrees
• Graduates
• Department
• Alumni
• Donors

Effect Of Motor-Assisted Elliptical Training Speed And Body Weight Support On Center Of Pressure Movement Variability, Farahnaz Fallahtafti, Chase M. Pfeifer, Thad W. Buster, Judith M. Burnfield

Department of Mechanical and Materials Engineering: Faculty Publications

Background: A motor-assisted elliptical trainer is being used clinically to help individuals with physical disabilities regain and/or retain walking ability and cardiorespiratory fitness. Unknown is how the device’s training parameters can be used to optimize movement variability and regularity. This study examined the effect of motor-assisted elliptical training speed as well as body weight support (BWS) on center of pressure (CoP) movement variability and regularity during training. Methods: CoP was recorded using in-shoe pressure insoles as participants motor-assisted elliptical trained at three speeds (20, 40, and 60 cycles per minute) each performed at four BWS levels (0%, 20%, 40%, and …

Me-Em Enewsbrief, September 2020, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.

Physical Behavior Of Thermally Affected Bronze And Brass, Samiul Kaiser, Mohammad Salim Kaiser

Journal of Mechanical Engineering Science and Technology (JMEST)

The physical behavior of thermally affected cast copper, aluminum bronze and brass has been studied by subjecting to heating isochronally for one hour at a range of 600°C. It shows that solid-solution hardening takes place into the Al added bronze and Zn added brass metal. Due to heating Al forms hard and brittle intermetallic of copper aluminates into the bronze metal which responses some age-hardening effects. The electrical conductivity of the metals increases initially through heat treatment due to stress relieving and finally decreases due to formation of intermetallic precipitates. The color of the heated samples are also studied through …

The Influence Of The Reference Area Of Aileron On The N2xx Aircraft Using Computational Fluid Dynamics, Siti Nur Rahmah, Gaguk Jatisukamto, Hary Sutjahjono

Journal of Mechanical Engineering Science and Technology (JMEST)

Aileron is a control surface that functions as a regulator of roll motion. The movements of the ailerons are opposite to the left and right sides. Previous studies have shown that graphs of hinge moment coefficient (Chm) values increases with increasing angle of attack. This study is to determine the aerodynamic characteristics of aileron by combining the surface area of the vane into the aileron by varying the aileron’s deflection. The calculation is performed using a numerical method in two dimensions (2D) commercial CFD simulation software. The results of the study concluded that the hinge moment coefficient for modified airfoil …

Hardness Evaluation On Ss 316l Joined With Gas Tungsten Arc Welding Under Constant Heat Treatment, Duwi Leksono, Imam Sudjono

Journal of Mechanical Engineering Science and Technology (JMEST)

The purpose of this study is to show the hardness of the GTAW welding results on SS 316L metal with surface heating during the welding process. Observations in this study used SS 316L material with heat temperature regulation on the metal surface of the welding process using heating variations of 100 ℃, 120 ℃ and 140 ℃. The welding process of SS 316L material used a welding joint model uses single V-type welding joint with an angle of 60°, a spacing of 2 mm, a root surface of 1 mm and a thickness of 5 mm. Vickers hardness test was …

The Effect Of Heat Treatment To The Erosion Rate Of Brass Composite, Aminnudin Aminnudin, Solichin Solichin

Journal of Mechanical Engineering Science and Technology (JMEST)

Brass composites can be improved their mechanical properties by the heat treatment process. The improvement of the mechanical properties of this technique is expected to increase the resistance of the composite to erosion that occurs in the environment of flow water. Brass composites used are compositeswith fly ash 5, 10, 15, and 20%. The heat treatment process was carried out using electric furnace withoutprotective gas. Composite heat up to 350°C and 400°C for 30 min. and quenching with water. Before and after the erosion test, the weight of the test specimen was weighed with analytical scales. The treatment process affects …

Performance Enhancement Of Shell And Tube Heat Exchanger On Parallel Flow With Single Segmental Baffle, Avita Ayu Permanasari, Poppy Puspitasari, Sukarni Sukarni, Retno Wulandari

Journal of Mechanical Engineering Science and Technology (JMEST)

The shell and tube heat exchanger was a tool to exchange the heat energy between fluids with different temperatures that occurred through direct or indirect contact. The energy exchange in fluids could be occurred with the same phase (liquid to liquid or gas to gas) or two fluids with different phase. To date, the process of heat transfer in the industrial field was crucial in machine work. Therefore, there were studies directed to optimize and develop the function and thermal performance of a heat exchanger by adding Baffles to the side of the shell. Vortex flow that occurs with the …

The Effect Of Solution Treatment Temperature And Quenching Media Variation In Heat Treatment Process Cu-Zn-Al Shape Memory Alloys On Shape Memory Effect And Microstructures, Wikan Jatimurti, Monica Gayatri K, Mavindra Ramadhani, Rochman Rochiem

Journal of Mechanical Engineering Science and Technology (JMEST)

Shape memory alloys (SMAs) are metal alloys with a reversible ability to recover their shape at a certain temperature after being deformed. This ability referred to as Shape Memory Effect (SME). The application of SMAs such as Ni-Ti and Cu-Zn-Al alloys usually used on automotive, biomedical, etc. The commonly used SMA is Ni-Ti because of its superior SME properties than Cu-Zn-Al, even though the price is quite higher. The SME of Cu-Zn-Al might be improved by increasing the presence of the martensite phase in its microstructure by heat treatment. The heat treatment process given to Cu-21Zn-5Al alloy is a homogenizing, …

Comparison Of Plantar Pressure Profile Of Young Adults During Training On Elliptical Devices And Overground Walking: A Pilot Study, Guilherme Manna Cesar, Thad W. Buster, Judith M. Burnfield

Department of Mechanical and Materials Engineering: Faculty Publications

Background: Elliptical training may offer advantages over other cardiorespiratory exercises for those requiring podiatric care, since its constant double-limb support diminishes recurring high-impact plantar forces while allowing exercise in a functional, upright posture. Unknown is the impact of distinct elliptical models, that can alter user’s body mechanics, on potential variations in plantar pressure patterns.

Purpose: To compare plantar pressure variables while exercising on four ellipticals and walking.

Methods: For this cross-sectional pilot study, plantar pressure data were recorded from ten young adults while exercising on four ellipticals (True, Octane, Life Fitness, SportsArt) and walking overground. One-way repeated measures ANOVA identified …

Magnetically Induced Carrier Distribution In A Composite Rod Of Piezoelectric Semiconductors And Piezomagnetics, Guolin Wang, Jinxi Liu, Wenjie Feng, Jiashi Yang

Department of Mechanical and Materials Engineering: Faculty Publications

In this work, we study the behavior of a composite rod consisting of a piezoelectric semiconductor layer and two piezomagnetic layers under an applied axial magnetic field. Based on the phenomenological theories of piezoelectric semiconductors and piezomagnetics, a one-dimensional model is developed from which an analytical solution is obtained. The explicit expressions of the coupled fields and the numerical results show that an axially applied magnetic field produces extensional deformation through piezomagnetic coupling, the extension then produces polarization through piezoelectric coupling, and the polarization then causes the redistribution of mobile charges. Thus, the composite rod exhibits a coupling between the …

Open-Source Digitally Replicable Lab-Grade Scales, Benjamin R. Hubbard, Joshua M. Pearce

Michigan Tech Publications, Part 1

This study provides designs for a low-cost, easily replicable open-source lab-grade digital scale that can be used as a precision balance. The design is such that it can be manufactured for use in most labs throughout the world with open-source RepRap-class material extrusion-based 3-D printers for the mechanical components and readily available open-source electronics including the Arduino Nano. Several versions of the design were fabricated and tested for precision and accuracy for a range of load cells. The results showed the open-source scale was found to be repeatable within 0.05 g with multiple load cells, with even better precision (0.005 …

Influence Of Elements Of Irrigation Equipment On Irrigation Erosion, M.M. Sarimsakov, O.S. Abdisamatov, Z.T. Umarova

Irrigation and Melioration

Irrigation erosion is a process that has a significant negative impact on agricultural production, which leads to a sharp decrease in soil fertility and productivity. The costs associated with growing crops will increase. Today, more than 720,000 irrigated lands in the country suffer from irrigation erosion. Studies have shown that in typical gray soils with a slope of more than 0.30, intensive irrigation of apple orchards leaches 24.6 tons of soil particles per hectare per season. Improved irrigation, that is, a decrease in the leaching of soil particles during irrigation using transverse barriers, was achieved by 6–12%. Irrigation reduces the …

Research Of Water Flow Motion In The Channel Of Amu-Bukhara Machine Channel, D.R. Bazarov, F. Artikbekova, M.P. Tashkhanova, B.M. Norkulov

Irrigation and Melioration

The article considers a numerical study of the movement of a water stream in the channel of the Amu Bukhara Machine Channel (ABMK). Water intake to the inlet canal is carried out from the Amu Darya river in a damless manner, therefore, ensuring the flow of clarified water into the anterior chambers of pumping stations is an urgent task. According to the developed model, consisting of hydrodynamic equations based on the laws of conservation of momentum and mass, data on the dynamics of velocities in the channel of the supply channel ABMK are obtained and zones of uneven flow in …

Irrigation Value The Mechanical Composition River Springs, A.M. Arifjanov, L.N. Samiev, F.K. Babajanov

Irrigation and Melioration

The article studies the influence of the fractional composition of river sediments on the soil structure of irrigated lands and on the process of soil formation. According to surveys in the Mirishkor canal, sediments formed in the river are distinguished by the distribution type in the main canal. The fractional composition of sediments mainly consists of particles of fine sand (0.1-0.05 mm) and coarse dust (0.05-0.001 mm).According to the results of surveys, by studying the mechanical composition of sediment in the channel, it will be possible to observe changes in the amount of composition, such as N-NH4, P2O5, K2O chemicals. …

Monitoring System For Electricity Consumption At Pumping Stations, N. Ikramov, T. Majidov, A. Mukhammadjonov

Irrigation and Melioration

Currently, in Uzbekistan, of 4.3 million hectares of irrigated land, 2.3 million hectares are provided with water supplied by pumping stations that are on the balance of the Ministry of water management of the Republic of Uzbekistan. In total, 1693 pumping stations with 5301 pumping units are operated, and the number of pumping stations ' personnel is about 16,000 people. The total capacity of these pumping stations is about 7000 m3/s. the Total annual energy consumption of these pumping stations is about 8.0 billion kW·h or about 12.5% of the annual electricity generation of the entire energy sector of Uzbekistan. …

Irrigation Value The Mechanical Composition River Spring The Effect Of The Inhomogeneity Of Elastic Medium On The Initiation Of Resonant Waves Under Moving Load, S.A. Abdukadirov, Z.S. Shаdmаnova, B.Sh. Yuldoshev

Irrigation and Melioration

investigated. The waveguide properties of the system are preliminarily studied. The multiple roots of the dispersion equations are revealed and the critical load velocities leading to the formation of resonance processes are determined. The solutions of the dispersion equations make it possible to determine the additional critical velocities in the mid-wave spectrum depending on the structure parameters. For simple models, analytical solutions of the development of resonance processes are obtained that are asymptotically correct for relatively large values of time. The computer simulations allow us to analyze the quantitative features of the process over the entire time period of the …

Substantiation Of Sprayers Installed To A Universal Mounted Sprayer, D. Dzhuraev, M.S. Halilov, S.M. Badalov, I.Zh. Toirov, A.E. Urishev

Irrigation and Melioration

The article presents the results of theoretical and experimental studies on the creation of primary sprayers for sprayers. The flow diagrams of the atomizers that were produced on the territory of the former Soviet Union are given. Currently, various types of spray guns are manufactured in America, Germany, France, Italy, Bulgaria and other countries. Based on the set requirements for sprayers, to ensure fluid flow and spraying when deployed 90-110 degrees on a plane, a slotted sprayer is selected - manufacturer Lechler of the brand ST-110-05 Germany, for installation on a universal mounted sprayer. The results of fluid flow by …

Technological Features Of Moistening Of Technical Seeds, O. Matchanov, B. Tuxtamishev

Irrigation and Melioration

This article describes the technological features of the reduction of technical varieties of cotton. Requirements for technical seeds in the processing of raw cotton are technical specifications and quality indicators. Seeds of technical cotton with quality indicators and adapted technical seeds must meet the requirements of technical conditions. The technical need for coated seeds should correspond to technical characteristics, such as reducing production costs, reducing moisture, long-term storage, improving quality, thermal conductivity, aerodynamic resistance, and heat resistance. From the point of view of heat treatment of seeds, parameters taking into account their thermophysical properties should be used to justify the …

Regulations Of Hydraulic Resistance Of Machine Channels Of Pumping Stations, D.R. Bazarov, B.R. Uralov, M.P. Tashkhanova

Irrigation and Melioration

The paper considers the general equation of fluid motion in the channels and the functional dependences of the hydraulic friction coefficient on the Reynolds number, relative roughness, and on the shape of the live section of the channel. Resistance formulas are given for the simplest cross-sectional shapes of channels and for channels with a more complex cross-sectional shape. To take into account the effect (on the pressure loss) of the channel cross-sectional shape and the presence of a flow with a free surface in it, additional correction factors are introduced (using the hydraulic radius concept) and be clarified as a …

Studying The Movement Of Crop Drined Seeds Of Cottage On A Slope Tray In A Protective Machine, R.K. Djamolov, A.A. Akrаmov, K. Djamolov

Irrigation and Melioration

The article presents the results of a theoretical study of the movement of pubescent cotton seeds along an inclined guide in a pickling machine. Equations are obtained that describe the movement of the seed along the inclined tray of the dresser. A formula is derived for determining the time of movement of the seed on an inclined one to the dressing agent. A plot of the change in the speed of the seed in the tray on the change in the angle of inclination and on the value of the movement of the seed. To increase the feed rate of …

Modernization Of Functions Of Management Of Land Use In The Conditions Of Innovative Economy, Sh.K. Narbaev

Irrigation and Melioration

Land use management, as a complex material-abstract system, is carried out through a number of its functions. The article provides an analysis of the functions of land management, improved the content of some functions and introduced additional new functions in the context of the development of an innovative economy. It is noted that improving the management system will increase the efficiency of land use, improve their environmental status, preserve landscape ecosystems based on the accelerated development of innovative activities. New land management functions are recommended: innovative land use development, territory development, land use technical support, remote study of land properties …

Combined Installation Photo Thermal Battery - Electric Water Heater To Provide Electricity And Water To Rural Households, R.A. Muminov, M.N. Tursunov, Х. Sabirov, U.R. Kholov, Т.Z. Аkhtamov, М. Eshmuradova

Irrigation and Melioration

The article presents the experimental results of the study of the parameters of a combined installation photo thermal battery – electric heater, used to provide electric energy and water to rural households. Photo thermal battery is made on the basis of photovoltaic batteries of crystalline silicon with an efficiency of ~ 20 %. Cellular polycarbonate was used as a heat sink. When creating the KU based on photo thermal battery EVN, modern efficient batteries, controllers, inverters and consumers of electric energy were used, and Ariston was chosen as the EVN. KU is adapted to climatic conditions, effectively and reliably provides …

Modeling The Movement Of A Heap In A Dielectric Sorting Device For Alfalfa Seeds, A. Lee, Z. Sharipov, M.N. Sattarov

Irrigation and Melioration

This article presents a theoretical study of modeling the movement of a mixture in a dielectric sorting plant for alfalfa seeds. Theoretical studies were carried out using the general laws of mechanics and mathematical modeling of alfalfa seeds, taking into account their physical and mechanical properties. The results of a theoretical study on modeling the detachment conditions of alfalfa seed heap particles and particle dynamics along the casing and pitched boards of a dielectric sorting device are presented. The differential equation with the initial conditions was solved by numerical methods of "Runge-Kutta-Felberg" with automatic step selection. The components of a …