Mechanical Engineering Commons^™

Designing A Naabsa Class Tanker Ship With Bottom Protection From Ground, Victor A. Kulesh, Mathias B. Prasetio, Fam Chung Hiep

Journal of Mechanical Engineering Science and Technology (JMEST)

Indonesia is the world's largest archipelago country with a high potential for economic development and top producer and exporter of palm oil. As an archipelago country, the most efficient cargo transportation routes are through rivers and seas. Designing and building tankers, taking into account the specifics of the operation, are relevant. The paper considers the issues of designing a tanker for the transportation of crude palm oil with a defined operation area and route. The general concept of the vessel is proposed, taking into account the restrictions on the navigation area and draft for operation in the river. Particular attention …

Effect Of Grafting Nano-Tio2 On Sansevieria Cylindrica Fiber Properties, Chrisrulita Sekaradi Wiguna, Heru Suryanto, Aminuddin Aminuddin, Jibril Maulana, Joseph Selvi Binoj, Alamry Ali

Journal of Mechanical Engineering Science and Technology (JMEST)

Natural fibers, which are abundant, environmentally friendly, and biodegradable, are used as a replacement for synthetic fibers. The composite strength can be increased by treating the surfaces of natural fibers with suitable chemicals, which can also improve the interface interaction between fiber and matrix. Application of a coupling agent in chemical treatment is utilized to reinforce the bonding between fiber and matrix. The objective of the study is to determine the influence of silane concentration on the Sansevieria cylindrica fiber properties. The methods included fibers treatment using ethanol and coupling agent as dissolving and TiO2 with concentrations of 0%, 0.25%, …

The Combustion Characteristics Of Calophyllum Inophyllum Fuel In The Presence Of Magnetic Field, Imam Rudi Sugara, Nasrul Ilminnafik, Salahuddin Junus, Muh Nurkoyim Kustanto, Yuni Hermawan

Journal of Mechanical Engineering Science and Technology (JMEST)

The study objective is to investigate the combustion characteristics of Callophyllum inophyllum fuel in presence of a magnetic fields. To conduct the experiment, a bunsen burner was utilized, with fuel and air being dispensed via a syringe pump and compressor, both regulated by a flowmeter. The fuel and air pipes were heated to 532.15 (K) to facilitate fuel evaporation. The equivalent ratio of 0.5, 1, and 1.5 was adjusted to control air discharge and fuel. An 11,000 gausses artificial magnet was used, with N-S, N-S, N-N, and SS being the various magnetic pole configurations. The study found that the magnetic …

Effect Of Current And Pulse-On Time On Material Removal Rate And Surface Roughness Of Tungsten Carbide In Electric Discharge Machine Die-Sinking, Mochamad Deny Riyanto, Andoko Andoko, Heru Suryanto

Journal of Mechanical Engineering Science and Technology (JMEST)

The focus of manufacturing for tungsten carbide applications often demands a smooth surface quality as the result of the Electric Discharge Machine (EDM) die-sinking process, especially in the manufacture of die and mold with tungsten carbide material processed using a die-sinking EDM machine. The purpose of this study is to analyze the effect of electric current and pulse-on time on the Material Removal Rate (MRR) and surface roughness of tungsten carbide. Through the experimental method, the parameters varied, namely electric current 17 A, 20 A, 23 A, and pulse-on time 30 µs, 55 µs, and 80 µs. MRR was calculated …

Lap Joint On St.37 Steel Plate With Friction Welding Clamping Method, Widia Setiawan, Nugroho Santoso, Wiyadi Wiyadi, Muhammad Sulistiyo Aji, Rachmat Alamin, Achsan Tarmudi

Journal of Mechanical Engineering Science and Technology (JMEST)

Friction stir (FW) welding is a relatively fresh method that was created and has been continually refined and adapted to industrial applications due to its benefits. This approach for solid-state joining entails connecting the components at a temperature below their melting point and then heating them up. Clamp joint applications are widely used using external heating and hitting with high strength, but the clamped joints with the FW method are rarely done. The research studied the characteristic of clamped joints at various plate thicknesses using the FW method. In this study, 30 specimens were used in the form of a …

The Effect Of Cutting Speed Of Nitrogen Laser Cutting On The Surface Texture Of Sus 304 Plate, Yanuar Rohmat Aji Pradana, Raka Afrianto, Chandra Hairat Abdul Rahman, Andoko Andoko

Journal of Mechanical Engineering Science and Technology (JMEST)

The focus of today’s machining industry is on how to maintain high productivity and low cost achieved by high tool life during the operation. Laser cutting is considered the right solution because it offers cutting speeds of up to 170000 mm/min through a non-contact process regardless of the workpiece material hardness. The aim of this study is to analyze the effect of cutting speed on the surface texture aspects namely surface roughness, kerf shape, and dross height on the stainless steel 304 plate after laser cutting. The nitrogen laser was utilized with the cutting speed of 400, 1700, and 2000 …

Analysis Of Fire And Smoke Spread In Ki Hajar Dewantara Auditorium, State University Of Jakarta, Using Fire Dynamics Simulator, Pratomo Setyadi, Ariq Harits Arrizq

Journal of Mechanical Engineering Science and Technology (JMEST)

Fire behavior and smoke spread are influenced by various factors, including the amount and condition of combustible material, ventilation openings, and ceiling height. A high amount of combustible material in the auditorium poses a significant fire hazard, hence, efforts need to be made to minimize the risk. One approach is to use Computational Fluid Dynamic software, such as Fire Dynamics Simulator (FDS), to model fire combustion. In this research, it provides an overview of the heat release rate (HRR) of fires that occur as well as the effect of differences in ceiling height and the effect of ventilation on fire …

Effect Of Temperature Variations Of Corn (Maize) Oil Biodiesel On Torque Values And Thermal Efficiency Of Diesel Engines, Suardi Suardi, Rodlian Jamal Ikhwani, Ade Putri Rezki Aulia

Journal of Mechanical Engineering Science and Technology (JMEST)

The trend of consumption of hydrocarbon fuels in Indonesia, which is increasing every year, is not accompanied by the amount of production, which is decreasing. Alternative fuels to reduce dependence on hydrocarbon fuels. One form of alternative fuel is biodiesel, which is made from corn (maize) oil. Corn oil itself, if processed, can be an option for clean and environmentally friendly energy option and that is the main objective of this research is to determine the performance of biodiesel corn oil on diesel engines. The method used in this study is an experimental method where corn oil biodiesel is tested …

Twin-Solute, Twin-Dislocation And Twin-Twin Interactions In Magnesium, Materials Yue, Jian Wang, Jian-Feng Nie

Department of Mechanical and Materials Engineering: Faculty Publications

Magnesium alloys have received considerable research interest due to their lightweight, high specific strength and excellent castability. However, their plastic deformation is more complicated compared to cubic materials, primarily because their low-symmetry hexagonal closepacked (hcp) crystal structure. Deformation twinning is a crucial plastic deformation mechanism in magnesium, and twins can affect the evolution of microstructure by interacting with other lattice defects, thereby affecting the mechanical properties. This paper provides a review of the interactions between deformation twins and lattice defects, such as solute atoms, dislocations and twins, in magnesium and its alloys. This review starts with interactions between twin boundaries …

Atomistic Simulations Of Twin Facets Associated With Three-Dimensional { []011 } Twins In Magnesium, Qiyu Zeng, Mingyu Gong, Houyu Ma, Yao Shen, Jian-Feng Nie, Jian Wang, Yue Liu

Department of Mechanical and Materials Engineering: Faculty Publications

Twinning is a deformation mechanism that creates three-dimensional (3D) twin domains through the migration of twin facets. This occurs via the nucleation and glide of twinning disconnections (TDs), which can pile up to create twin facets. A comprehensive under- standing of twin facets associated with 3D twins, including their atomic structures and energies, is crucial for understanding deformation twinning. In this study, we propose a molecular statics/dynamics (MS/MD) approach to determine characteristic twin facets enclosing 3D non-equilibrium/equilibrium { [] 011 } twin domains, which has been much less studied than the counterpart { [] 012 } twin domains. The stability …

The Essential Work Of Fracture In Peridynamics, Christer Stenström, Kjell Eriksson, Florin Bobaru, Stefan Golling, Pär Jonsén

Department of Mechanical and Materials Engineering: Faculty Publications

In this work, the essential work of fracture (EWF) method is introduced for a peridynamic (PD) material model to characterize fracture toughness of ductile materials. First, an analytical derivation for the path-independence of the PD J -integral is provided. Thereafter, the classical J -integral and PD J-integral are computed on a number of analytical crack problems, for subsequent investigation on how it performs under large scale yielding of thin sheets. To represent a highly nonlinear elastic behavior, a new adaptive bond stiffness calibration and a modified bonddamage model with gradual softening are proposed. The model is employed for two …

Mesoporous Particle Embedded Nanofibrous Scaffolds Sustain Biological Factors For Tendon Tissue Engineering, Chiara Rinoldi, Ewa KijeńSka-GawrońSka, Marcin Heljak, Jakub Jaroszewicz, Artur KamińSki, Ali Khademhosseini, Ali Tamayol, Wojciech Swieszkowski

Department of Mechanical and Materials Engineering: Faculty Publications

In recent years, fiber-based systems have been explored in the frame of tissue engineering due to their robustness in recapitulating the architecture and mechanical properties of native tissues. Such scaffolds offer anisotropic architecture capable of reproducing the native collagen fibers’ orientation and distribution. Moreover, fibrous constructs might provide a biomimetic environment for cell encapsulation and proliferation as well as influence their orientation and distribution. In this work, we combine two fiber fabrication techniques, such as electrospinning and wet-spinning, in order to obtain novel cell-laden 3D fibrous layered scaffolds which can simultaneously provide: (i) mechanical support; (ii) suitable microenvironment for 3D …

A Strong And Ductile Cobalt-Free Solid-Solution Fe30ni30mn30cr10 Multi-Principal Element Alloy From Hot Rolling, Hans Pommerenke, Jiaqi Duan, Nathan Curtis, Victor Delibera, Adam Bratten, Andrew Hoffman, Mario Buchely, Ronald O'Malley, Haiming Wen

Materials Science and Engineering Faculty Research & Creative Works

Most of the face-centered cubic (FCC) multi-principal element alloys (MPEAs) developed thus far contain cobalt. for many applications, it is either required or beneficial to avoid cobalt, since cobalt has long-term activation issue (for nuclear applications), is expensive, and is considered a critical material. in addition, FCC structured solid-solution MPEAs tend to have relatively low strength. an FCC solid-solution Fe30Ni30Mn30Cr10 (at %) MPEA was fabricated via arc melting, followed by homogenization at 1100 °C for 12 h. the alloy was hot rolled at 1100 °C with a total reduction of up to 97 %. the microstructure was characterized, and mechanical …

The Plastics Collection Reference Packet, Special Collections Research Center

Special Collections Research Center

This reference packet is an informational tool to support further research into the history of plastics—whether interested in companies, individuals within the plastics industry's history, historical plastics materials, essays, and more. All content featured within this packet was previously published on the former plastics.syr.edu website as part of a Syracuse University Libraries and Special Collections Research Center (SCRC) partnership established in 2007 with the Plastics Pioneers Association (PPA)—an association of plastics industry professionals interested in preserving the plastics industry's past.

Nitric Oxide: Physiological Functions, Delivery, And Biomedical Applications, Syed Muntazir Andrabi, Navatha Shree Sharma, Anik Karan, S. M. Shatil Shahriar, Brent Cordon, Bing Ma, Jingwei Xie

Department of Mechanical and Materials Engineering: Faculty Publications

Nitric oxide (NO) is a gaseous molecule that has a central role in signaling pathways involved in numerous physiological processes (e.g., vasodilation, neurotransmission, inflammation, apoptosis, and tumor growth). Due to its gaseous form, NO has a short half-life, and its physiology role is concentration dependent, often restricting its function to a target site. Providing NO from an external source is beneficial in promoting cellular functions and treatment of different pathological conditions. Hence, the multifaceted role of NO in physiology and pathology has garnered massive interest in developing strategies to deliver exogenous NO for the treatment of various regenerative and biomedical …

Design And Development Of Ultrabroadband, High-Gain, And High-Isolation Thz Mimo Antenna With A Complementary Split-Ring Resonator Metamaterial, Ammar Armghan, Khaled Aliqab, Meshari Alsharari, Osamah Alsalman, Juveriya Parmar, Shobhit K. Patel

Department of Mechanical and Materials Engineering: Faculty Publications

The need for high-speed communication has created a way to design THz antennas that operate at high frequencies, speeds, and data rates. In this manuscript, a THz MIMO antenna is designed using a metamaterial. The two-port antenna design proposed uses a complementary splitring resonator patch. The design results are also compared with a simple patch antenna to show the improvement. The design shows a better isolation of 50 dB. A broadband width of 8.3 THz is achieved using this complementary split-ring resonator design. The percentage bandwidth is 90%, showing an ultrabroadband response. The highest gain of 10.34 dB is achieved …

Restoration Of Normal Blood Flow In Atherosclerotic Arteries Promotes Plaque Stabilization, Morgan A. Schake, Ian Mccue, Evan T. Curtis, Thomas J. Ripperda Jr., Samuel Harvey, Bryan T. Hackfort, Anna Fitzwater, Yiannis S. Chatzizisis, Forrest Kievit, Ryan M. Pedrigi

Department of Mechanical and Materials Engineering: Faculty Publications

Blood flow is a key regulator of atherosclerosis. Disturbed blood flow promotes atherosclerotic plaque development, whereas normal blood flow protects against plaque development. We hypothesized that normal blood flow is also therapeutic, if it were able to be restored within atherosclerotic arteries. Apolipoprotein E-deficient (ApoE^-/-) mice were initially instrumented with a blood flow-modifying cuff to induce plaque development and then five weeks later the cuffwas removed to allowrestoration of normal blood flow. Plaques in decuffed mice exhibited compositional changes that indicated increased stability compared to plaques in mice with the cuff maintained. The therapeutic benefit of decuffingwas comparable …

Comparative Cutting Fluid Study On Optimum Grinding Parameters Of Ti-6al-4v Alloy Using Flood, Minimum Quantity Lubrication (Mql), And Nanofluid Mql (Nmql), Jaime Taha-Tijerina, Immanuel A. Edinbarough

Informatics and Engineering Systems Faculty Publications

Titanium alloys have been of paramount interest to the aerospace industry due to their attractive characteristics. However, these alloys are difficult to machine and require grinding post-processes for quality assurance of the products. Conventional grinding takes a long time and uses a flood coolant-lubrication technique, which is not cost effective nor environmentally friendly. Several studies have been performed to prove the viability and benefit of using Minimum Quantity Lubrication (MQL) with vegetable or synthetic-ester fluids. This work aims to find the optimum grinding parameters of creep feed grinding Ti-6Al-4V with a green silicon carbide wheel, using a flood lubrication system …

Morphology And Hemodynamics Of Cerebral Arteries And Aneurysms In A Rare Pair Of Monozygotic Twins, Hang Yi, Zifeng Yang, Luke C. Bramlage, Bryan R. Ludwig

Mechanical and Materials Engineering Faculty Publications

In this preliminary study, the underlying pathophysiology mechanisms of cerebral aneurysms (CAs) in monozygotic twins (MTs) were investigated via a rare pair of MTs (twin A and twin B) involving four reconstructed arterial models using preclinical information. First, dimensions and configurated outlines of three-perspective geometries were compared. Adopting an in-vitro validated numerical CA model, hemodynamic characteristics were investigated in the MTs, respectively. Despite expected genetic similarities, morphological comparisons show that configurations of cerebral arteries exhibit significant differences between the twins. The ICA size of twin A is larger than that in twin B (2.23~25.86%), varying with specific locations, attributing to …

The Center For Centering Dome, Olek Piechaczek, Ryan M. Scharf

Architectural Engineering

The Center for Centering seeks to create a large-scale healing center, conducive to individual centering of the mind and body. This mobile installation provides a relaxing, enclosed space while still maintaining a connection to the outdoors. The clients liked the idea of having a pop-up installation that could be easily set up as a touring display. With a deadline for installation looming in June 2022, a team of students had five months to design and manufacture the structure.

In winter 2022, the students developed custom geometry to minimize the number of individual parts and built a ¼ scale model of …

Exploring The Intersection Of Biology And Design For Product Innovations, Ajay P. Malshe, Salil Bapat, Kamlakar Rajurkar, Ang Ang, Jean-Marc Linares

Department of Mechanical and Materials Engineering: Faculty Publications

Design, development, productization, and applications of advanced product concepts are pressing for higher multifunctionality, resilience, and maximization of available resources equitably to meet the growing and continuing demands of global customers. These demands have further accelerated during the recent COVID- 19 pandemic and are continuing to be a challenge. Engineering designs are one of the most effective ways to endow products with functions, resilience, and sustainability. Biology, through millions of years of evolution, has met these acute requirements under severe resource and environmental constraints. As the manufacturing of products is reaching the fundamental limits of raw materials, labor, and resource …

Self-Assembly Of Exfoliated Graphene Flakes As Anticorrosive Coatings For Additive Manufactured Steels, Kaleb Hood, Wen Qian, Yi Xia, Savannah Krupa, Annie Dao, Sarah Ahmed, Samuel Olson, Nam Nguyen, Joseph A. Turner, Jun Jiao

Department of Mechanical and Materials Engineering: Faculty Publications

This study demonstrates the feasibility of using liquid exfoliation of expandable graphite into multilayer exfoliated graphene flakes (EGFs) to form a self-assembled thin film on an air–water interface. The film can coat the surface of additive manufactured (AM) steel substrates to enhance surface properties, specifically AM 316 stainless-steel (AM316), AM 8620 steel (AM8620), and samples of the same alloys made by conventional manufacturing (CM) processes. Liquid exfoliation offers a high yield route for an EGF coating that can cover up to 95% of the sample surface with a single application. The thin, flexible EGFs can coat a rough AM metal …

Exploring Methods For Recycling Filament Waste In 3d Printing, Max Rios Carballo

Publications and Research

The goal of the current study is to investigate cutting-edge techniques for recycling filament waste from 3D printing procedures. Appropriate waste management techniques are required to reduce this trash's harmful environmental consequences. The goal of the project is to look at new methods for recycling filament waste in order to minimize disposal and encourage reuse. To acquire data from pertinent papers and research, a thorough literature review methodology was used. The findings show that this issue may be resolved utilizing a variety of recycling techniques, including shredding, melting, and re-extrusion. The type of filament waste and the intended goal will …

Mesoscale Modeling And Machine Learning Studies Of Grain Boundary Segregation In Metallic Alloys, Malek Alkayyali

All Dissertations

Nearly all structural and functional materials are polycrystalline alloys; they are composed of differently oriented crystalline grains that are joined at internal interfaces termed grain boundaries (GBs). It is well accepted that GB dynamics play a critical role in many phenomena during materials processing or under operating environments. Of particular interest are GB migration and grain growth processes, as they influence many crystal-size dependent properties, such as mechanical strength and electrical conductivity.

In metallic alloys, GBs offer a plethora of preferential atomic sites for alloying elements to occupy. Indeed, recent experimental studies employing in-situ microscopy revealed strong GB solute segregation …

Machine Learning-Based Data And Model Driven Bayesian Uncertanity Quantification Of Inverse Problems For Suspended Non-Structural System, Zhiyuan Qin

All Dissertations

Inverse problems involve extracting the internal structure of a physical system from noisy measurement data. In many fields, the Bayesian inference is used to address the ill-conditioned nature of the inverse problem by incorporating prior information through an initial distribution. In the nonparametric Bayesian framework, surrogate models such as Gaussian Processes or Deep Neural Networks are used as flexible and effective probabilistic modeling tools to overcome the high-dimensional curse and reduce computational costs. In practical systems and computer models, uncertainties can be addressed through parameter calibration, sensitivity analysis, and uncertainty quantification, leading to improved reliability and robustness of decision and …

Metastability And Degradation In Cu(In,Ga)Se2 Thin-Film Solar Cells, Mohsen Jahandardoost

UNLV Theses, Dissertations, Professional Papers, and Capstones

Cu(In,Ga)(S,Se)2 or CIGS is a thin-film semiconductor that has shown a device efficiency of 23.35% and 24.2% for single-junction and perovskite/CIGS tandem solar cells, respectively. CIGS offers promising properties such as tunable bandgap and ease of processing making them great candidates for thin-film tandem devices. However, knowledge of the effect of material defects, buffer materials, and post-deposition treatment (PDT) on degradation and metastability behavior in these devices is not well understood.In this dissertation, metastability and long-term degradation of CIGS thin-film solar cells have been investigated under combinatorial stress factors of heat, light, and voltage bias to systematically understand the effect …

Me-Em Enewsbrief, March 2023, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.

Classification Of Electrical Current Used In Electroplastic Forming, Tyler Grimm

All Dissertations

Electrically assisted manufacturing (EAM) is the direct application of an electric current to a workpiece during manufacturing. This advanced manufacturing process has been shown to produce anomalous effects which extend beyond the current state of modeling of thermal influences. These purported non-thermal effects have collectively been termed electroplastic effects (EPEs).

While there is a distinct difference in results between steady-state (ideal DC) testing and pulsed current testing, the very definition of these two EAM methods has not been well established. A "long" pulse may be considered DC current; a "short" pulse may produce electroplastic effects; and even "steady-state" current shapes …

High-Yield Bioinspired Atmospheric Water Capture Through Hydrogels, Yiwei Gao

UNLV Theses, Dissertations, Professional Papers, and Capstones

Water scarcity is a global issue affecting billions of people, and atmospheric water harvesting (AWH) technology has been identified as a potential solution. However, existing single-material AWH approaches have limited water harvesting yields due to alternated water capture, storage, and release stages, and only function within a high relative humidity range. In my doctoral research project, we developed a bio-inspired, hydrogel-based multi-layer AWH approach that allows for segregated capture, storage, and release stages, and is envisioned to have higher daily water harvesting efficiency even in low-humidity areas. My research began with understanding the relations between hydrogel mechanical stiffness, hydraulic permeability, …

Shape Memory Polymer-Based Multifunctional Syntactic Foams, Siavash Sarrafan

LSU Doctoral Dissertations

With the increase in popularity of shape memory polymers (SMPs), especially in applications such as aerospace, textile, biomedical engineering, and even structures, the weight of the material and the devices made with it has always been a crucial factor. Using the shape memory polymer as a matrix to make a syntactic foam is one of the best and most affordable approaches to creating a lighter material that still has the shape memory effect. The addition of particles of different stiffness, strength, and size, with variable fractions, creates a composite that enables engineering the mechanical, as well as other physical and …