Mechanical Engineering Commons^™

Effect Of The Homogenization Process On Titanium Oxide-Reinforced Nanocellulose Composite Membranes, Taufiq Mahsuli, Aisyah Larasati, Aminnudin Aminnudin, Jibril Maulana

Journal of Mechanical Engineering Science and Technology (JMEST)

Indonesian pineapple production can reach 200 tons per day; however, pineapples generate a significant amount of waste. Pineapple peel waste can be used to make membranes. Composite membranes containing TiO2 have dense properties, low porosity, and increase the mechanical strength of the cellulose sheet. This research uses various ultrasonic homogenizers to homogenize the distribution of nanocellulose and TiO2 (50% and 100% power with 30, 60, and 90 minutes). The casting method is used to shape the membrane. The SEM test shows that the higher the power used and the longer the sonication time, the less agglomeration of about 1.63%/ cm2 …

Effect Of Heating Temperature, Holding Time And Stabilization Temperature On The Al-Foam Properties, Dewi Puspitasari, Poppy Puspitasari, Mazli Mustapha, Turnad Lenggo Ginta

Journal of Mechanical Engineering Science and Technology (JMEST)

The interest in metallic foam is increasing since their cellular structures have a unique combination of properties such as high stiffness, low density, lightweight, high specific strength, and thermal insulation. Commonly, the performance of metallic foam can be improved by the heat treatment process. However, the previous heat treatment methods still present the brittle crack path and the research on heat treatments of the metal foam properties is very limited. In this study, individual parameters in stress relieving treatment that contribute to Al-Foam properties were investigated. The stress-relieving process of the samples was performed using a vacuum furnace. The composition …

Vertical Shaft Kinetic Turbine Performance Using A Cup-Shape Blade, Kennie A. Lempoy, Nita C. V. Monintja, Arwanto M. A. Lakat

Journal of Mechanical Engineering Science and Technology (JMEST)

The abundant availability of alternative energy sources forms the fundamental foundation for rural energy development. In particular, renewable energy sources are indispensable in rural areas due to their ecofriendly nature and widespread accessibility, which helps preserve the environment by avoiding pollution. Indonesia, a country blessed with vast water resources, especially its rivers, holds enormous potential for harnessing kinetic energy derived from fast-flowing river waters. Effective utilization of this kinetic energy has the potential to address energy shortages in the country. In this context, there is a pressing need to enhance the efficiency of kinetic turbines designed to function as electricity …

Photocatalytic Scheme With External Magnetic Field On Coffee Waste In Hydrogen Production, Abid Fahreza Alphanoda, Eko Prasetyo, Wisnu Broto

Journal of Mechanical Engineering Science and Technology (JMEST)

Photocatalytic is considered a deadlock-breaking technology for renewable energy and lowering environmental pollutants. Photocatalytic efficiency efforts are improved by activating the photocatalyst to introduce an external magnetic field. This review highlights recent breakthroughs by comparing original coffee waste, activation of coffee waste with the addition of catalysts, and manipulation of spin electrons by applying external magnets. Characterization was done with FTIR to look at chemical bonds, UV-Vis with Tauc's Relation approach to measure bandgap, and material morphology using SEM EDX. The increase in photocatalyst activation aligns with the decrease in bandgap value. The rate of decline in bandgap is in …

Artificial Neural Network-Based Modeling Of Performance Spark Ignition Engine Fuelled With Bioethanol And Gasoline, Susi Marianingsih, Farhanna Mar’I, Hendry Y. Nanlohy

Journal of Mechanical Engineering Science and Technology (JMEST)

Machine learning technology can distinguish the relationship between engine characteristics and performances. Therefore, the goal of the present work is to predict the performance parameters of a singlecylinder 4-stroke gasoline engine at different ignition timings using a blended mixture of gasoline and bioethanol by an artificial neural network (ANN). Experimental data for training and testing in the proposed ANN was obtained at a dynamic speed and full load condition. An ANN model was developed based on standard Back-Propagation algorithm for the spark ignition engine. Multi-layer perception network (MLP) was used for non-linear mapping between the input and output parameters. An …

The Effect Of Adding Aluminium On The Performance Of Zno Nrs/Pani In Their Application As Photoelectrochemical Water Splitting, Eprilia Trikusuma Sari, Nandang Mufti, Anissa Chairani Alfin Nadhira, Hari Wisodo, Markus Diantoro

Journal of Mechanical Engineering Science and Technology (JMEST)

Photoelectrochemical (PEC) is a new renewable energy technology that converts H2O into hydrogen and oxygen gas with the help of sunlight. A photoelectrochemical cell device consists of three main components, one of which is the photoanode. One of the materials that can be used as a photoanode is ZnO which has good electrical properties and is non-toxic. Nanorods-structured ZnO has the advantage of being able to increase light absorption due to its high surface area. However, the resulting performance is still quite low. So it is necessary to make modifications to the photoanode, one of which is by adding aluminium …

What Does It Mean To Be “Prepared For Work”? Perceptions Of New Engineers, Jessica R. Deters, Marie C. Paretti, Logan A. Perry, Robin Ott

Department of Mechanical and Materials Engineering: Faculty Publications

Background: Engineering education seeks to prepare students for engineering practice, but the concept of preparedness is often ill-defined. Moreover, findings from studies of different populations or in different contexts vary regarding how well new graduates are prepared. These variations, coupled with the lack of clarity, suggest the need to better understand what it means to be prepared for engineering work.

Purpose: This study contributes to research on workplace preparation by exploring how new graduates describe being prepared for engineering work.

Method: Applying secondary analysis to data from the multi-institution Capstone To Work (C2W) project, we used thematic …

Implementation Of Experimental Static Recrystallization Of High Strength Steel Into Computational Simulation Of Multi-Pass Slab Hot Rolling, S. K. Dasari, S. Ganguly, A. Abutunis, K. Chandrashekhara, M. F. Buchely, S. N. Lekakh, R. J. O'Malley, T. Natarajan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Microstructural changes and softening due to static recrystallization have a critical influence on thermo-mechanical behavior of high strength steels during industrial multi-pass hot rolling. Numerical simulation using finite element analysis (FEA) can be used to accurately predict the softening behavior during the hot rolling process. Therefore, the implementation of an experimentally defined static recrystallization model into FEA is necessary to get realistic simulation prediction. in this study, the extent of softening during static recrystallization in Si and Mn alloyed high strength steel was measured using double hit tests. a Gleeble™ thermo-mechanical simulator was used to perform the double hit tests …

Impact Of Silicon Ion Irradiation On Aluminum Nitride-Transduced Microelectromechanical Resonators, David D. Lynes, Joshua Young, Eric Lang, Hengky Chandrahalim

Faculty Publications

Microelectromechanical systems (MEMS) resonators use is widespread, from electronic filters and oscillators to physical sensors such as accelerometers and gyroscopes. These devices' ubiquity, small size, and low power consumption make them ideal for use in systems such as CubeSats, micro aerial vehicles, autonomous underwater vehicles, and micro-robots operating in radiation environments. Radiation's interaction with materials manifests as atomic displacement and ionization, resulting in mechanical and electronic property changes, photocurrents, and charge buildup. This study examines silicon (Si) ion irradiation's interaction with piezoelectrically transduced MEMS resonators. Furthermore, the effect of adding a dielectric silicon oxide (SiO₂) thin film is …

A Review On The Coalescence Of Confined Drops With A Focus On Scaling Laws For The Growth Of The Liquid Bridge, Sangjin Ryu, Haipeng Zhang, Udochukwu John Anuta

Department of Mechanical and Materials Engineering: Faculty Publications

The surface–tension-driven coalescence of drops has been extensively studied because of the omnipresence of the phenomenon and its significance in various natural and engineering systems. When two drops come into contact, a liquid bridge is formed between them and then grows in its lateral dimensions. As a result, the two drops merge to become a bigger drop. The growth dynamics of the bridge are governed by a balance between the driving force and the viscous and inertial resistances of involved liquids, and it is usually represented by power–law scaling relations on the temporal evolution of the bridge dimension. Such scaling …

Revealing Interface-Assisted Plastic Anisotropy Via In Situ Transmission Electron Microscopy Tension Of Lamellar Tial, Zhixiang Qi, Qi Zhu, Jian Wang, Yuede Cao, Fengrui Chen, Jiangwei Wang, Yang Chen, Gong Zheng, Guang Chen

Department of Mechanical and Materials Engineering: Faculty Publications

Assembling functional units into specific orientation organizations based on functional unit and organization (FUO) paradigm can maximize utilizing mechanical property anisotropy of lamellar-structured materials. However, the origin of their anisotropic deformation behaviors has not been clearly understood. Taking the fully lamellar γ-TiAl/ α₂-Ti₃Al dual-phase single crystal as an example, we decouple the interface functional units governed anisotropic plastic deformation through in situ transmission electron microscopy tensile testing and multiscale microstructural characterizations. The orientation organization-dependent slip continuity across the γ/α₂ interface and interface strength play a determinant role in plastic anisotropy beyond intrinsic dislocation activities within …

Steerable Acoustically Powered Starfish-Inspired Microrobot, Cornel Dillinger, Justin Knipper, Nitesh Nama, Daniel Ahmed

Department of Mechanical and Materials Engineering: Faculty Publications

Soft polymeric microrobots that can be loaded with nanocargoes and driven via external field stimuli can provide innovative solutions in various fields, including precise microscale assembly, targeted therapeutics, microsurgery, and the capture and degradation of unwanted wastewater fragments. However, in aquatic environments, it remains challenging to operate with microrobotic devices due to the predominant viscous resistances and the robots’ limited actuation and sensing capabilities attributed to their miniaturization. The miniature size prevents the incorporation of onboard batteries that can provide sufficient power for propulsion and navigation, necessitating a wireless power supply. Current research examines untethered microrobot manipulation using external magnetic, …

Transepithelial Electrical Impedance Increase Following Porous Substrate Electroporation Enables Label-Free Delivery, Justin R. Brooks, Tyler C. Heiman, Sawyer R. Lorenzen, Ikhlaas Mungloo, Siamak Mirfendereski, Jae Sung Park, Ruiguo Yang

Department of Mechanical and Materials Engineering: Faculty Publications

Porous substrate electroporation (PSEP) is a promising new method for delivering molecules such as proteins and nucleic acids into cells for biomedical research. Although many applications have been demonstrated, fundamentals of the PSEP delivery process are not yet well understood, partly because most PSEP studies rely solely on fluorescent imaging for evaluating delivery and quantifying successful outcomes. Although effective, only utilizing imaging alone limits our understanding of the intermediate processes leading to intracellular delivery. Since PSEP is an electrical process, electrical impedance measurements are a natural addition to fluorescent imaging for PSEP characterization. In this study, we developed an integrated …

Increased Ductility Of Ti-6al-4v By Interlayer Milling During Directed Energy Deposition, Rakeshkumar Karunakaran, Luz D. Sotelo, Hitarth Maharaja, Calsey Nez, Monsuru Ramoni, Scott Halliday, Sushil Mishra, Joseph A. Turner, Michael P. Sealy

Department of Mechanical and Materials Engineering: Faculty Publications

Additive manufacturing (AM) often results in high strength but poor ductility in titanium alloys. Hybrid AM is a solution capable of improving both ductility and strength. In this study, hybrid AM of Ti-6Al-4V was achieved by coupling directed energy deposition with interlayer machining. The microstructure, residual stress, and microhardness were examined to explain how interlayer machining caused a 63% improvement in ductility while retaining an equivalent strength to as-printed samples. Interlayer machining introduced recurrent interruptions in printing that allowed for slow cooling-induced coarsening of acicular α laths at the machined interfaces. The coarse α laths on the selectively machined layers …

Acoustophoresis Around An Elastic Scatterer In A Standing Wave Field, Khemraj Gautam Kshetri, Nitesh Nama

Department of Mechanical and Materials Engineering: Faculty Publications

Acoustofluidic systems often employ prefabricated acoustic scatterers that perturb the imposed acoustic field to realize the acoustophoresis of immersed microparticles. We present a numerical study to investigate the timeaveraged streaming and radiation force fields around a scatterer. Based on the streaming and radiation force field, we obtain the trajectories of the immersed microparticles with varying sizes and identify a critical transition size at which the motion of immersed microparticles in the vicinity of a prefabricated scatterer shifts from being streaming dominated to radiation dominated. We consider a range of acoustic frequencies to reveal that the critical transition size decreases with …

Me-Em Enewsbrief, September 2023, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.

Switching Methods For Three-Dimensional Rotational Dynamics Using Modified Rodrigues Parameters, Matthew Jarrett Banks

Mechanical & Aerospace Engineering Theses & Dissertations

A rigid body in space has three degrees of rotational freedom. As a result, a minimum of three independent parameters is required to define the three-dimensional orientation of a rigid body. As is well known, every set of three independent parameters has at least one orientation where mathematical or geometrical singularities are encountered; therefore, when the use of a three-parameter representation is desired, a method for singularity avoidance must also be considered. A common practice for singularity avoidance is to switch between parameter sets whose singularities occur at different orientations. With this in mind, modified Rodrigues parameters (MRP) are considered …

Aquaculture In Hydropower Reservoirs, Racheal Macharia

Tanzania Journal of Engineering and Technology (TJET)

There is an undoubtedly existing relationship between water, energy, and food and their interaction with the natural environment and mankind. Climate change is the talk of the day in global development discussions as it intensifies water shortages, energy, poverty, food shortages, and environmental degradation. Currently, most of the hydropower dams constructed in Africa are majorly built to store water for agricultural purposes, control flooding, and generate electricity. Notable projects include the seven forks hydropower stations located on the Tana River in Kenya; Aswan high dam in Egypt; Grand Renaissance dam in Ethiopia; Kariba dam in Zimbabwe and Akosombo in Ghana. …

Stomatal Opening Efficiency Is Controlled By Cell Wall Organization In Arabidopsis Thaliana, Sedighe Keynia, Leila Jaafar, You Zhou, Charles T. Anderson, Joseph A. Turner

Department of Mechanical and Materials Engineering: Faculty Publications

Stomatal function in plants is regulated by the nanoscale architecture of the cell wall and turgor pressure, which together control stomatal pore size to facilitate gas exchange and photosynthesis. The mechanical properties of the cell wall and cell geometry are critical determinants of stomatal dynamics. However, the specific biomechanical functions of wall constituents, for example, cellulose and pectins, and their impact on the work required to open or close the stomatal pore are unclear. Here, we use nanoindentation in normal and lateral directions, computational modeling, and microscopic imaging of cells from the model plant Arabidopsis thaliana to investigate the precise …

Me-Em Enewsbrief, June 2023, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.

Nanoscale Modeling Of Membrane Systems Under Mechanical Deformation In Traumatic Brain Injury Using Molecular Dynamics, Anh Thi Ngoc Vo

Theses and Dissertations

Neuronal membrane disruption and mechanoporation are nanoscale damage mechanisms that critically affect brain cell viability during traumatic brain injury (TBI). These nanoscale cellular impairments are elusive in experiments and necessitate in silico approaches such as molecular dynamics (MD) simulations. Implementing MD, this research aims to investigate the effects of different key factors related to membrane deformation and damage, including force field resolutions, lipid compositions, and loading conditions.

To examine the impact of force field resolution, MD deformation simulations were conducted on 1-palmitoyl-2-oleoyl-sn-glycero-3-phosphatidylcholine (POPC) lipid bilayer membranes, using all-atom (AA), united-atom (UA), and coarse-grained Martini (CG-M) force fields. The mechanical responses …

Influence Of Forming Forces On Torsional, Tensile, And Compressive Deformation Of Paperboard Packages, Arvo Niini, Panu Tanninen, Juha Varis, Ville Leminen

Journal of Applied Packaging Research

Paperboard packages were tested mechanically to investigate influence of forming forces on torsional, tensile, and compressive deformation. The packages were paperboard trays which were press formed with different pressing forces and blank holder forces. Deformation of the trays was observed with torsion, compression, and tensile tests. A statistical analysis of test results was conducted to derive optimal forming forces. Increased pressing force yielded desirable deformation characteristics with the trays. Blank holder force had largest impact on the compressive deformation. Interaction of the pressing force and the blank holder force influenced the torsional and the compressive deformation. The optimal forming forces …

Machine Learning Based Average Pressure Coefficient Prediction For Isolated High-Rise Buildings, Shiva Sai Reddy Marapakala

ETD Archive

In structural design, the distribution of wind-induced pressure exerted on structures is crucial. The pressure distribution for a particular building is often determined by scale model tests in boundary layer wind tunnels (BLWTs). For all combinations of interesting building shapes and wind factors, experiments with BLWTs must be done. Resource or physical testing restrictions may limit the acquisition of needed data because this procedure might be time-and resource-intensive. Finding a trustworthy method to cyber-enhance data-collecting operations in BLWTs is therefore sought.

This research analyzes how machine learning approaches may improve traditional BLWT modeling to increase the information obtained from tests …

Development, Experimental Validation, And Progressive Failure Modeling Of An Ultra-Thin High Stiffness Deployable Composite Boom For In-Space Applications, Jimesh D. Bhagatji

Mechanical & Aerospace Engineering Theses & Dissertations

To maximize the capabilities of nano- and micro-class satellites, which are limited by their size, weight, and power, advancements in deployable mechanisms with a high deployable surface area to packaging volume ratio are necessary. Without progress in understanding the mechanics of high-strain materials and structures, the development of compact deployable mechanisms for this class of satellites would be difficult. This research focuses on fabrication, experimental testing, and progressive failure modelling to study the deformation of an ultra-thin composite beam. The research study examines deformation modes of a boom under repetitive pure bending loads using 4-point bending setup. The material and …

Multiscale Modeling And Gaussian Process Regression For Applications In Composite Materials, Joshua Arp

All Dissertations

An ongoing challenge in advanced materials design is the development of accurate multiscale models that consider uncertainty while establishing a link between knowledge or information about constituent materials to overall composite properties. Successful models can accurately predict composite properties, reducing the high financial and labor costs associated with experimental determination and accelerating material innovation. Whereas early pioneers in micromechanics developed simplistic theoretical models to map these relationships, modern advances in computer technology have enabled detailed simulators capable of accurately predicting complex and multiscale phenomena.

This work advances domain knowledge via two means: firstly, through the development of high-fidelity, physics-based finite …

Double Cantilever Beam Mode-I Testing Validation In Large-Scale Additive Manufacturing Carbon Composite, Luis Alfonso Camacho

Open Access Theses & Dissertations

Testing for mechanical properties for additive manufacturing has been based on already existing standards for traditional manufacturing methods. For composites in large scale additive manufacturing there is a research gap in bond strength and fracture toughness for a single layer interface. By using Double cantilever beam Mode I, this thesis manuscript validates testing parameters and protocols to describe the intricacies of ABS matrix 20 wt.% carbon filled composite, specifically on the layer-to-layer interface. Studies suggest that fracture toughness is sensitive to process parameters, like deflection speed and sharpened crack tip at the layer interface of BAAM 3D printed part and …

Characterization Of Mechanically Recycled Polylactic Acid (Pla) Filament For 3d-Printing By Evaluating Mechanical, Thermal, And Chemical Properties And Process Performance, Mahsa Shabani Samghabady

All Theses

Polylactic acid (PLA) is a biopolymer made from renewable resources such as sugar and corn. PLA filament is a popular material used in Fused Deposition Modeling (FDM) 3D-printing. While this material has many advantages, all the failed parts, support structures, rafts, nozzle tests, and the many prototype iterations during the 3D-printing process contribute to the plastic pollution and release of greenhouse gases. Although PLA is biodegradable, it can take years to degrade in landfills. Instead of throwing away PLA waste and buying new filaments, PLA can be recycled. Amongst the different recycling technologies, mechanical recycling is the most environmentally friendly. …

Theoretical And Experimental Study Of Active Magnetic Bearing Control Integrated On Bently's Rotor Kit, Arturo Mario Flores

Master's Theses

This thesis focuses on the comprehensive study of controlling a customized Active Magnetic Bearing (AMB) installed on Bently Nevada’s RK4 rotor kit in Cal Poly’s Vibrations and Rotordynamics Lab. The AMB was uniquely designed and manufactured by a Cal Poly senior project team to fit Bently’s rotor kit and the results of this research are distinctive to the custom system. To achieve practical functionality of the AMB system, we designed a controller a Virtual Instrument (VI) using the National Instrument software, LabVIEW. From the experimental study, we calibrated the programming to find unknown parameters of the AMB system and validated …

Mechanical Properties Of Biocomposite With Various Composition Of Caco3 And Starch, Agris Setiawan, Fransisca Diana Wahyuningsih, Riria Zendy Mirahati

Journal of Mechanical Engineering Science and Technology (JMEST)

Calcium carbonate has the potential to be used in the development of medical materials, including biomaterials. Biocomposite is composed of CaCO3 as matrix material and bioplastic from the combination of corn starch and cassava starch as reinforcement. This study aims to determine mechanical properties such as tensile strength and bending/flexural strength with varying compositions of CaCO3 and bioplastic. Characterization of the biocomposite uses Scanning Electron Microscope to observe the microstructure and composition elements of their structure. This study used 4 variations in the ratio of CaCO3 suspension: (Corn Starch + Cassava Starch). Each sample was characterized using specimen code A …

Synthesis And Characterization Of Nitrogen-Doped Activated Carbon For Lithium Battery Anode Applications, Prihanto Trihutomo, Poppy Puspitasari, Muhammad Bustomi Radja, Milzam Rahmat Busono

Journal of Mechanical Engineering Science and Technology (JMEST)

Nitrogen-dopped activated carbon was synthesized to see its effect on the characterization of the nitrogen surface functional groups, crystal size, and morphology of the resulting sample. Synthesis of nitrogen-doped activated carbon was carried out by varying the addition of Urea as a nitrogen doping source. Activated carbon compared its characteristics with variations in the concentration of added Urea to activated carbon, at 1:3 and 1:5. The FTIR results obtained were the presence of functional groups indicating the presence of nitrogen bonds in each sample. The crystallinity results showed that the samples were classified as crystalline and nitrogen doping influenced the …