Mechanical Engineering Commons^™

Hydrogen Fuel Cells, Sydney Pilgrim, Skyler Smith

ENgaging Educators in Renewable enerGY (ENERGY): Lesson Plans & Slideshows (2017-2019)

Hydrogen fuel cells are hydrogen powered energy sources. They convert chemical energy into electrical energy by separating water molecules into the two elements that make up water, Hydrogen (2) and Oxygen (1). Hydrogen fuel cells are looking to become a paramount energy producer to avoid consuming fossil fuels for power. Along with the abundance of Hydrogen in the atmosphere being a benefit of using Hydrogen powered fuel cells, the only emission from these energy sources is water vapor. Many car engines only operate at a 20% fuel efficiency, whereas fuel cell powered cars utilize 60% of the energy produced. Although …

Solar Tracking Sustainable Energy Education, Tara Hart, Donita Legonas

ENgaging Educators in Renewable enerGY (ENERGY): Lesson Plans & Slideshows (2017-2019)

Two middle school science teachers collaborated with Georgia Southern lab students to conduct research and experimentation on the benefits of utilizing a dual-axis solar tracking system to assess the amount of voltage received during various times of the day. A smaller similar dual-axis solar tracking system was designed and fabricated to utilize in the teachers’ middle school classrooms in the study of renewable energy and the engineering and design process.

Optimal Sintering Temperature Of Ceria-Doped Scandia Stabilized Zirconia For Use In Solid Oxide Fuel Cells, Amanda K. Assuncao

Honors Undergraduate Theses

Carbon emissions are known to cause decay of the Ozone layer in addition to creating pollutant, poisonous air. This has become a growing concern among scientists and engineers across the globe; if this issue is not addressed, it is likely that the Earth will suffer catastrophic consequences. One of the main culprits of these harmful carbon emissions is fuel combustion. Between vehicles, power plants, airplanes, and ships, the world consumes an extraordinary amount of oil and fuel which all contributes to the emissions problem. Therefore, it is crucial to develop alternative energy sources that minimize the impact on the environment. …

Hosting Capacity Optimization In Modern Distribution Grids, Mansoor T. Alturki

Electronic Theses and Dissertations

The availability of distributed renewable energy resources and the anticipated increase in new types of loads are changing the way electricity is being produced and supplied to consumers. This shift is moving away from a network delivering power solely from centralized power plants towards a decentralized network which supplements its power production by incorporating local distributed generators (DGs). However, the increased integration of DGs into existing distribution networks is impacting their behavior in terms of voltage profile, reliability, and power quality. To determine the maximum amount of DG that distribution grids can accommodate the concept of hosting capacity is introduced. …

Automated Cfd Optimization To Maximize Wind Farms Performance And Land Use, Rafael Valotta Rodrigues

Electronic Theses and Dissertations

In this research, a computational system was designed to analyze and optimize the layout of wind farms under variable operational conditions. At first, a wind turbine computational fluid dynamic (CFD) model was developed covering the near wake. The near wake flow field was validated against near wake velocity data from the MEXICO experiment. The CFD simulation demonstrated that the tip speed ratio and the pitch angle greatly influence the near wake behavior, affecting the velocity deficit and the turbulence intensity profile in this region. The CFD model was extended to cover the far wake, aiming to become a computational tool …

Pressure-Driven Stabilization Of Capacitive Deionization, Landon S. Caudill

Theses and Dissertations--Mechanical and Aerospace Engineering

The effects of system pressure on the performance stability of flow-through capacitive deionization (CDI) cells was investigated. Initial data showed that the highly porous carbon electrodes possessed air/oxygen in the micropores, and the increased system pressure boosts the gases solubility in saline solution and carries them out of the cell in the effluent. Upon applying a potential difference to the electrodes, capacitive-based ion adsorption occurs in competition with faradaic reactions that consume oxygen. Through the addition of backpressure, the rate of degradation decreases, allowing the cell to maintain its salt adsorption capacity (SAC) longer. The removal of oxygen from the …

Test 2207: Challenger Mt743, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2205: Challenger Mt738, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2202: John Deere 6215r Autoquad-Plus, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2200a: New Holland Workmaster 70, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2200: Case Ih Farmall 70a, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Test 2190a: New Holland Workmaster 50, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Investigation On The Potential Of A Co2 Capture System, Downstream Of The Aftertreatment System For A Heavy-Duty Engine Application, Murchana Pathak

Dissertations, Master's Theses and Master's Reports

The transportation sector accounts for the second largest source of CO₂ emissions after power generation. New Corporate Average Fuel Economy (CAFE) regulations are focusing on improving energy through reduced fuel consumption and greenhouse gas emissions. This work investigates the potential of a CO₂ capture system downstream of an aftertreatment system for a heavy-duty engine application. Amine absorption has been described as one of the most effective ways to capture CO₂ from the exhaust for point sources. Therefore, using thermal-swing absorption process with potassium carbonate (K₂CO₃) as the absorbent liquid, a process was analyzed …

The Interaction Of Ignition And In-Cylinder Flow On Flame Kernel Development And Its Impacts On Combustion In An Optically Accessible Direct Injection Engine, Yanyu Wang

Dissertations, Master's Theses and Master's Reports

A significant challenge facing spark-ignited (SI) engines to achieve higher efficiency via highly diluted combustion is the quickly increased combustion instability as the dilution level increases. The flow motion variation has been identified as a dominant factor that introduces combustion variability at highly diluted conditions. However, the detailed mechanism of how the variation in flow motion impacts the flame kernel development and introduces combustion instability is only partially understood. This research investigated the impacts of the in-cylinder flow on variability of the ignition and early flame kernel development in a single cylinder direct-injection spark-ignition (DI-SI) optically accessible engine and accessory …

Experimental And Modeling Study Of Particulate Matter Oxidation Under Loading Conditions For A Scr Catalyst On A Diesel Particulate Filter, Abhishek Jadav

Dissertations, Master's Theses and Master's Reports

The heavy-duty diesel engines use a Diesel Oxidation Catalyst (DOC), a Catalyzed Particulate Filter (CPF), a Selective Catalytic Reduction (SCR) with urea injection and a Ammonia Oxidation Catalyst (AMOX), to meet the US EPA 2010/2013 particulate matter (PM) and NO_x emission standards. However, it is not possible to achieve the 2015 California low NO_x standards with this arrangement. Hence, there is a need to improve the existing aftertreatment system. This can be achieved by coating the SCR catalyst on a diesel particulate filter (DPF), thus combining the PM filtration and NO_x reduction functionality into a single device. …

Physical Modeling Of Lithium-Ion Aging For Automotive Applications, Anurag Kamal

Dissertations, Master's Theses and Master's Reports

This thesis extends the full-scale electrochemical model for a Lithium-ion battery based on the porous electrode theory to incorporate aging mechanisms of solid electrolyte interface formation, cyclic electrode degradation, and lithium plating during overcharge, automotive vibrations, mechanical stress, and cell temperature, as reported in the existing literature. Further, the thesis presents the scope of the parameters used in the model to enable designers to extend the equations for new mechanisms and variability of other parameters.

An increased set of equations makes the complexity of the model even higher, and it would be very computationally complex to simulate this model. This …

Nebraska Summary: S1150 Challenger 1050, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Optimization And Control Of An Array Of Wave Energy Converters, Jianyang Lyu

Dissertations, Master's Theses and Master's Reports

This study explored optimal configuration of both the array layout and the dimension of each WEC in the array. The array contains heaving buoys with full interaction and exact hydrodynamics. Optimization of dimension was done on each WEC in the array with a given optimal layout, and a higher q-factor was achieved. Both impedance matching optimal control and derivative control were employed, which provides both theoretical maximum energy and a more realistic case. Then the work was expanded to optimization of both the array layout and the dimension of each WEC in the array. An average of 39.21% higher q-factor …

Smart Prismatic Louver Technology For Enhanced Daylighting And Management Of Thermal Loads In Green Buildings, Michael Alva

Dissertations and Theses

Abstract

Two significant design strategies for mitigating building energy consumption are daylight redirection and solar energy harvesting. Good daylighting implementation enhances the amount of useful natural light within a space, thereby offsetting the need for electric lighting. Solar energy harvesting systems can mitigate energy costs from mechanical systems by managing incoming thermal loads or capturing solar energy that can be used to supplement thermal systems in the building. While there are many available façade-based technologies that can perform daylighting or solar thermal energy harvesting, there remains a limitation in available systems that can perform both simultaneously. The proposed Liquid Filled …

Structural And Aerodynamic Design, Procedure And Analysis Of A Small V-Shaped Vertical Axis Wind Turbine, Odari J. Whyte

College of Graduate Studies: Theses & Dissertations

Over the last two decades there has been a renewed interest in Vertical Axis Wind Turbines. This turbine configuration though unpopular for large-scale generation has found a niche market in the way of offshore energy harvesting. However, offshore wind has its challenges. In this thesis a detailed comprehensive study of a proposed V-shaped vertical axis turbine rotor is performed in order to examine its structural and aerodynamic characteristics. The design met and exceeded the safety parameters establish for test bed operation, showing a factor of safety of 1.87 with regard to fatigue stress response. A satisfactory fatigue stress design life …

Investigation Of Combustion Characteristics Of A Heavy-Duty Diesel Engine Retrofitted To Natural Gas Spark Ignition Operation, Jinlong Liu

Graduate Theses, Dissertations, and Problem Reports (ETD)

The conversion of existing diesel engines to natural-gas spark ignition operation by adding a gas injector in the intake manifold for fuel delivery and replacing the diesel fuel injector with a spark plug to initiate and control the combustion process can reduce U.S. dependence on petroleum imports and curtail engine-out emissions. As the conventional diesel combustion chamber (i.e., flat head and bowl-in-piston) creates high turbulence, the engine can operate leaner, which would increase its efficiency and reduce emissions. However, natural gas combustion in such retrofitted engines presents differences compared to that in conventional spark ignited engines. Subsequently, the main goal …

Design And Optimization Of A 1 Kw Stirling Engine, Garrett Tyler Rinker

Graduate Theses, Dissertations, and Problem Reports (ETD)

Stirling engines are often overlooked as a means of energy conversion, though its versatility offers many advantages. Since it is an external combustion engine, it can be supplied with heat through the combustion of a variety of fuels. Its maintenance- and degradation-free aspects, as well as its excellent turn down ratio, make it a suitable candidate for applications such as remote power generation, combined heat and power (CHP), cryogenics, solar power, and even space exploration. The continual advancement of additive manufacturing (AM) offers opportunity to potentially further improve the already efficient Stirling cycle. This dissertation presents the design and optimization …

Designing And Testing 3-D Printed Wafer-Box With Embedded Pzt Sensors To Identify The Shape Effect On Energy Harvesting, Ahmad Jami Safayet

College of Graduate Studies: Theses & Dissertations

Piezoelectric energy has been recently paid attention in the field of alternative energy. Day by day the traditional energy sources including Coal tar and oils are becoming scarce. People are heading to an alternative energy source to meet the future energy demand. Piezoelectric energy is one of the competitive energy sources compared to the conventional renewable energy sources including solar, wind, and geothermal power and so on. This energy production method bears enormous research potential because it can be used as the roadway for a new method of power generation. This research project aimed to identify which shaped wafer-box produced …

An Integrated Closed Convergent System For Optimal Extraction Of Head-Driven Tidal Energy, Michelle Ann Vieira

UNF Graduate Theses and Dissertations

As the demands for energy increased with the global increase in population, there is a need to create and invest in more clean and renewable energy sources. Energy derived from the movement of the tides is an ancient concept that is currently being harnessed in a handful of large tidal range locations. However, the need to move from fossil fuel driven energy sources to those that are clean and non-polluting is a priority for a sustainable future. Globally, hydropower potential is estimated to be more than 16,400-Terawatt hours annually. Given that the electricity consumption worldwide was at 15,068-Terawatt hours in …

Spray And Combustion Studies Of High Reactivity Gasoline In Comparison To Diesel Under Advanced Compression Ignition Engine Conditions, Meng Tang

Dissertations, Master's Theses and Master's Reports

Gasoline compression ignition (GCI) technology has demonstrated great potentials in improving fuel economy and reducing engine-out NO_x and particulate matter emissions. Development and application of the GCI technology on multi-cylinder engines require both fundamental understandings of the gasoline spray combustion characteristics and accurate numerical tools. Due to the large differences in the thermo-physical and the chemical properties between gasoline and diesel range fuels, differences in the spray combustion characteristics between gasoline and diesel is expected. Reports on the gasoline spray combustion characteristics under conditions relevant to medium to heavy-duty engines are scarce and this dissertation aims to fill in …

Exploring Energy, Comfort, And Building Health Impacts Of Deep Setback And Normal Occupancy Smart Thermostat Implementation, Zachary Ethan Alderman

Graduate Theses and Dissertations

As smart thermostat adoption rates continue to increase, it becomes worthwhile to explore what unanticipated outcomes may result in their use. Specific attention was paid to smart thermostat impacts to deep setback and normal occupancy states in a variety of conditions while complying with the ventilation and temperature requirements of ASHRAE 90.2-2013. Custom weather models and occupancy schedules were generated to efficiently explore a combination of weather conditions, building constructions, and occupancy states. The custom modeling approach was combined with previous experimental data within the Openstudio graphics interface to the EnergyPlus building modeling engine. Results indicate smart thermostats add the …

Design And Validation Of An Experimental Setup To Study Single Phase Heat Transfer Enhancement Of Femtosecond Laser Processed Metallic Surfaces, Sarah Jane Wallis

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

In the present work, a single phase flow heat transfer experimental loop was designed with the intention of studying the effects of femtosecond laser surface processing (FLSP) on metallic surfaces with the specific goal of enhancing heat transfer in compact heat exchangers currently in use by NASA. This experimental setup went through two major design iterations which are detailed in this thesis. The first iteration consisted of a counterflow fluid-to-fluid heat exchanger, which measured overall heat transfer coefficients and pressure drops, where the overall heat transfer coefficient is defined in terms of the total thermal resistance to heat transfer between …

Pollution Prevention In The Great Lakes Basin: Working With Pulp & Paper Manufacturers, Eugene Park

Journal of Environmental Sustainability

In response to growing concerns over persistent toxic substances in the Great Lakes, new initiatives are in place to address and mitigate pollutant loadings to these large natural waterbodies. With support from the U.S. Environmental Protection Agency and New York Department of Environmental Conservation, the New York State Pollution Prevention Institute (NYSP2I) worked with pulp & paper companies in the Great Lakes Basin in an effort to find solutions to reduce environmental impacts from this industry sector. Based on currently available EPA toolkits, NYSP2I developed and utilized an assessment tool called Lean, Energy, and Environment (LE2). Five different paper manufacturers …

Development, Energy, And Climate Change Policy: Enabling Sustainable Development Through Access To Energy, Robert J. Brecha

Biennial Conference: The Social Practice of Human Rights

Human rights, human development, and climate change clearly overlap in many ways. Development, as quantified by the Human Development Index (HDI), for example, has historically been strongly correlated with energy consumption. This fact is recognized in Sustainable Development Goal (SDG) 7, to “ensure access to affordable, reliable, sustainable and modern energy for all.” Currently the world is in the midst of a large wave of human migration, much of it involuntary and due to stymied development opportunities as well as political upheaval. Climate change will become, or already is, an exacerbating factor in migration dynamics.

A pertinent question is how …

A Strategic Development Of Alternative Fuel Initiation And Its Adaptation In A Developing Country : A Feasibility Study On Methanol Fuelled Domestic Passenger Ships In Indonesia, Eko Maja Priyanto

World Maritime University Dissertations

No abstract provided.