Mechanical Engineering Commons^™

Bidirectional Electrowetting Actuation With Voltage Polarity Dependence, Nathan B. Crane, Alex A. Volinsky, Pradeep Mishra, Ajay Rajgadkar, Mehdi Khodayari

Faculty Publications

This work presents an electrowetting system in which the actuation direction depends on the polarity of the applied voltage. Since electrowetting response depends on the voltage squared, it is typically independent of voltage sign to first order. However, the introduction of an electrochemicaal diode into the equivalent electrical circuit permits polarity-dependent behavior. Electrochemical diodes were created by making holes in the dielectric. The aluminum electrodes passivate and prevent current flow in one direction, creating diode-like behavior with high breakdown voltage. The resulting actuation forces were directly measured and are of comparable magnitude for both actuation directions.

Integrated Vehicle Thermal Management For Advanced Vehicle Propulsion Technologies: Preprint., K. Bennion, M. Thornton

Publications (T)

A critical element to the success of new propulsion technologies that enable reductions in fuel use is the integration of component thermal management technologies within a viable vehicle package. Vehicle operation requires vehicle thermal management systems capable of balancing the needs of multiple vehicle systems that may require heat for operation, require cooling to reject heat, or require operation within specified temperature ranges. As vehicle propulsion transitions away from a single form of vehicle propulsion based solely on conventional internal combustion engines (ICEs) toward a wider array of choices including more electrically dominant systems such as plug-in hybrid electric vehicles …

Technology Improvement Pathways To Cost-Effective Vehicle Electrification: Preprint, A. Brooker, M. Thornton, J. Rugh

Publications (T)

Electrifying transportation can reduce or eliminate dependence on foreign fuels, emission of green house gases, and emission of pollutants. One challenge is finding a pathway for vehicles that gains wide market acceptance to achieve a meaningful benefit. This paper evaluates several approaches aimed at making plug-in electric vehicles (EV) and plug-in hybrid electric vehicles (PHEVs) cost-effective including opportunity charging, replacing the battery over the vehicle life, improving battery life, reducing battery cost, and providing electric power directly to the vehicle during a portion of its travel. Many combinations of PHEV electric range and battery power are included. For each case, …

The Influence Of Branches In The Performance Of Power-Line Communication Systems That Use Mc-Coma With Reed Solomon Coding, Emmanuel Felix

Tanzania Journal of Engineering and Technology (TJET)

Power-line network is proposed as an infrastructure for Information and Communications Technologies (ICTs)
services provision. However, there are a number of factors that contribute greatly to power-line communication performance degradation. These include number of branches that can be added or removed from the power- line network, lengths of the branch lines, loading etc. It has been pointed out that the number of branches is one of the factors that affects power-line performance to a certain extent. In this paper the influence of number of branches on the performance of Broadband Power-line communication (BPLC) that uses MC- CDMA modulation scheme with …

Investigation Into Contact Resistance And Damage Of Metal Contacts Used In Rf-Mems Switches, Kevin W. Gilbert

Theses and Dissertations

This research examines the physical and electrical processes involved in lifecycle failure of Microelectromechanical (MEMS) Radio-Frequency (RF) cantilever beam ohmic contact switches. Failures of these switches generally occur at the contact, but complete details of performance of microcontacts are difficult to measure and have not been previously reported. This study investigated the mechanics of microcontact behavior by designing and constructing a novel experimental setup. Three representative contact materials of varying microstructure (Au, Au5%Ru, Au4%V₂O₅) were tested and parameters of contact during cycling were measured. The Au4%V₂O₅, a dispersion strengthened material developed at …

Shaped Mems Contact, Ronald A. Coutu Jr., Paul E. Kladitis, Robert L. Crane

AFIT Patents

A MEMS switch fabrication process and apparatus inclusive of a bulbous rounded surface movable contact assembly that is integral with the switch movable element and achieving of long contact wear life with low contact electrical resistance. The disclosed process is compatible with semiconductor integrated circuit fabrication materials and procedures and includes an unusual photoresist reflow step in which the bulbous contact shape is quickly defined in three dimensions from more easily achieved integrated circuit mask and etching-defined precursor shapes. A plurality of differing photoresist materials are used in the process. A large part of the contact and contact spring formation …

On-Line Realtime Water Quality Monitoring And Control For Swimming Pools, Paul Duffy, Gerard Woods, Sean O'Hogain, James Walsh, C. Caplier

Conference Papers

Effective swimming pool water quality monitoring and control systems are important to safeguard public health and for bather comfort. Most Irish swimming pool monitoring systems rely heavily on manual methods for sampling, testing and data recording of important parameters. Microbiological testing is infrequent and results can often take days. The goal of this research is to develop a water quality monitoring and control system with real time data logging, automatic data analysis, remote monitoring and control, microbiological sampling capabilities and online connectivity. National Instruments hardware and its software package LabView form the basis of the monitoring and control system. Several …

Development Of A Low Cost Handheld Microfluidic Phosphate Colorimeter For Water Quality Analysis, Sean C. Kaylor

Master's Theses

This thesis describes the design, fabrication, and testing process for a microfluidic phosphate colorimeter utilized for water quality analysis. The device can be powered by, and interfaced for data collection with, a common cell phone or laptop to dramatically reduce costs. Unlike commercially available colorimeters, this device does not require the user to measure or mix sample and reagent. A disposable poly(dimethylsiloxane) (PDMS) microfluid chip, powered by an absorption pumping mechanism, was used to draw water samples, mix the sample at a specific ratio with a molybdovanadate reagent, and load both fluids into an onboard cuvette for colorimetric analysis. A …

Stability Analysis, Modeling, Simulation And Experimental Testing Of An Ems Maglev System With Structural Flexibility, Aravind M. Hanasoge

Mechanical & Aerospace Engineering Theses & Dissertations

Vehicle-guideway interaction studies of Magnetically Levitated (Maglev) vehicles indicate that structural flexibility can adversely affect the overall stability and performance of such systems. This is one of the reasons why guideways are generally made very rigid. This in turn leads to increased cost of the overall system since guideway construction forms a significant portion of the overall cost. In this dissertation, the influence of structural flexibility on the stability of Electromagnetic Suspension (EMS) Maglev systems is studied. It is shown how inherently unstable and flexible structure EMS Maglev systems can achieve guaranteed stability by using collocated actuators and sensors, along …

Electro Mechanical Actuator Test Stand For In-Flight Experiments, Michael Koopmans, Catlin Mattheis, Austin Lawrence

Mechanical Engineering

The Prognostic Center of Excellence at NASA Ames is currently researching actuator prognostics, specifically in the application of electro mechanical actuators (EMA’s). Cal Poly ME students Michael Koopmans and Catlin Mattheis and EE student Austin Lawrence have chosen to undertake the task of building a test stand that will be flown in flight while testing EMA’s specific faults. A stand was designed to fit inside a standard 19” rack, take power from the aircraft 3 EMA’s, a computer, data acquisition, and electric magnets switches are powered. A MIL STD 1553 interface is present to allow fault injection. Vibration and temperature …

Advanced Design And Performance Characterization Of A Micromachined Tuning-Fork Gyroscope With High Quality Factors, Shiva Krishna Durgam

Mechanical & Aerospace Engineering Theses & Dissertations

Over the past two decades, micromachined gyroscopes fabricated using MicroElectroMechanical Systems (MEMS) technology have attracted a great deal of attention from various industrial and military sectors due to their significant advantages over traditional bulky gyroscopes, including small size, batch fabrication, low power consumption, and low cost. Among the various micromachined gyroscopes developed so far, tuning-fork gyroscopes with integrated electrostatic transducers have been extremely attractive because of their significant advantages over other structural forms and other types of transducers., including larger proof mass, large vibration amplitude in the drive-mode, and relative ease of fabrication.

This thesis presents the advanced design and …

The Design And Verification Of A Mems Combustor Chamber, Constance Yvonne Meadors

Theses and Dissertations

A pre-combustion micro-mixing chamber has been designed as a component of the University of Arkansas at Little Rock's (UALR) proposed complete microelectromechanical (MEMS) hybrid rocket on a silicon chip. A MEMS pre-combustion mixer allows identification of pressures and flow rates for stochiometric mixing of combustion gases. The pre-combustion mixer has been designed to interface with a mass spectrometer for detection and characterization of combustion reactants and products as the first stage of a UALR hybrid micro-thruster. This research focuses on the design, fabrication, and validation of a pre-combustion micro-mixer that satisfies the requirements of MEMS micro-spacecraft and operates in space …

Modeling Of The Interior Electric Field In Photovoltaic Cells, Tara Jeatran

The Journal of Undergraduate Research

With the emergence of photovoltaic technologies, there is a strong technological demand for high-performance photovoltaic devices. One of the most promising device concepts developed at SDSU is organic-based photovoltaic cells. The performance of the PV cells is controlled by charge generation and charge separation, and charge transportation processes. Extraordinary control over the properties of the organic photovoltaic materials will be needed in order for this research to succeed. Therefore, the interior electric field and the macro electric properties of the system are the foundation behind these facts and are critical properties on their performance. In this paper, the fundamentals of …

Abatteuses Forestières : Dispositif Et Circuits De Commande Relatifs À La Sécurité, Laurent Giraud, Yuvin Chinniah, Damien Burlet-Vienney, Joseph-Jean Paques, Marina Koutchouk, Renaud Daigle

Rapports de recherche scientifique

Les abatteuses forestières sont des engins tout-terrains conçus pour évoluer en forêt, qui servent de véhicule moteur pour déplacer une tête d’abattage.

L’utilisation d’abatteuses avec une tête d’abattage multifonctionnelle s’est largement répandue au Québec ces dernières années pour deux raisons :

• Cette méthode d’abattage réduit la machinerie car une seule machine tronçonne et façonne les arbres en billots, là où il en fallait plusieurs avec les anciennes méthodes;
• La méthode d’abattage abîme moins le sol de la forêt car le façonnage des arbres se fait sur place et crée ainsi un tapis végétal.

L’IRSST a lancé une série d’études sur …

Development Of Miniature Hybrid Rockets For Orbital Upkeep And Transfer Applications In Nano/Pico-Satellites, Derek Willingham

Mechanical Engineering Undergraduate Honors Theses

This research has developed and constructed a successful miniature hybrid rocket test assembly for research into hybrid rocket scaling issues. It is hoped that such systems will find eventual integration into small satellites. The test assembly houses 3" fuel grains and provides an inlet for gaseous oxidizer. Although far from complete, preliminary data were taken with PMMA and GOx and some useful conclusions were drawn that will benefit future research into this topic. Fuel grains with combustion chambers whose diameters range from 1/16" to 3/8" were tested at different flow rates and thrust data gathered. Maximum flow information was gathered …

Restart Capabilities Of Hybrid Rocket Motor Utilizing Gaseous Propane And Oxygen Injection System, Joseph Gracy

Mechanical Engineering Undergraduate Honors Theses

Hybrid rockets have become an increasingly popular application in professional and amateur rocketry for their outstanding performance and reliability. An issue pressing the marketability and functionality of these rockets is the ability to restart with an exclusive system after primary ignition. Research and development of a system that can be used reliably in either application to achieve restart under various conditions has been made recently using dual injection of GOX and C3H8 using a 200kV ignition system while implementing a polymethylmethacrylate (PMMA) formable polymer as primary fuel. The system used a manual valve arrangement for control. The design features most …

A Review Of Variable Valve Timing Devices, Paul Shelton

Mechanical Engineering Undergraduate Honors Theses

Variable valve timing (VVT) has evolved from simple, manual controlled engine management to automatic, electronic works of engineering. Starting from the need for more power and extending into fuel efficiency and low emissions, VVT has evolved from the constant changing of needs. This paper summarizes various devices used to control the timing of valves from the early 1920s up until 2007.

Development And Validation Of A Dynamic Model Of The Maglev Transportation System At Old Dominion University, Ajinkya V. Deodhar

Mechanical & Aerospace Engineering Theses & Dissertations

A dynamic model for the vehicle-guideway coupled with a controller is developed using dynamic modelling software, MADYMO. The fundamental characteristics of the vehicle are obtained from detailed FE analysis in NASTRAN. The vehicle is then converted into a 21-degree-of-freedom rigid body system with 12 FE magnets. A two span concrete guideway of 54 meters in length is modelled using 3D solid Hex8 elements. The air gap is modelled as a penetration of the magnets in the guideway. The PD controller aims at achieving constant penetration (i.e. the air gap) of all magnets in the guideway, throughout the simulation. This PD …

Electrically Steerable Diffraction Gratings For Hyperspectral Imaging: A Microelectromechanical System Design And Fabrication, Saban Atinc Delican

Theses and Dissertations

The current research is focused on the design and fabrication of an electrically programmable diffraction grating using standard micro electro mechanical systems (MEMS) technology. The goal is to design a beam steering element required to build very small hyperspectral imaging (HSI) sensors. The diffraction grating will be used to perform beam-dispersion - a critical step in the imaging process. The proposed transmissive diffraction grating based approach will minimize the overall size and the number of components in the physical design of the hyperspectral imagers, thereby enabling us to exploit the traditional advantages of MEMS such as increased reliability, smaller size, …

Factors Affecting The Spread Of A Bioterrorist Agent Throughout A Building, William A. Cantrell

Inquiry: The University of Arkansas Undergraduate Research Journal

Bioterrorism has become a greater concern for Americans since the 2001 anthrax letters. Recent studies have explored the possibilities of biological attacks, and most deal with possible large-scale attacks. However, there is reason to believe that small-scale attacks are more likely. Even though there have been investigations of the postal delivery system and the spread of bioagents through mail, few if any studies have looked at attack on a single building and the resultant spread form room to room. One particular method of attacking a building would be a single-even release of an aerosol bioagent in the building. This paper …

Performance Comparison Of Pb(Zr0.52Ti0.48)O3-Only And Pb(Zr0.52Ti0.48)O3-On-Silicon Resonators, Hengky Chandrahalim, Sunil A. Bhave, Ronald G. Polcawich, Jeff Pulskamp, Dan Judy, Roger Kaul, Madan Dubey

Faculty Publications

This paper provides a quantitative comparison and explores the design space of lead zirconium titanate (PZT)–only and PZT-on-silicon length-extensional mode resonators for incorporation into radio frequency microelectromechanical system filters and oscillators. We experimentally measured the correlation of motional impedance (R_X) and quality factor (Q) with the resonators’ silicon layer thickness (t_Si). For identical lateral dimensions and PZT-layer thicknesses (t_PZT), the PZT-on-silicon resonator has higher resonant frequency (f_C), higher Q (5100 versus 140), lower R_X (51 Ω versus 205 Ω), and better linearity [third-order input intercept …

Analysis Of Wind Turbine Transverse Vibration, Matt Hein, Whitney Karpen

The Journal of Undergraduate Research

Large wind turbines have become an appealing choice for renewable electrical energy production throughout the world. The United States Midwest contains massive potential for wind energy development and is therefore being primed for large wind turbines to harvest this resource and bring it to market. Because of this, safety concerns have arisen in regard to their ability to withstand the harsh climate of the region. Analysis of the transverse vibration caused by severe weather will be preformed. A simplified model will allow for an analytical solution and displacement graphs produced with MATLAB code. This information will allow for an unbiased …

Development And Validation Of A Dynamic Model Of The Maglev Transportation System At Old Dominion University, Ajinkya Deodhar, Sebastian Bawab, Aravind Hanasoge

Mechanical & Aerospace Engineering Faculty Publications

A dynamic model of the vehicle/guideway coupled with a controller is developed for the maglev demonstration system currently being developed at ODU, using the MAthematical DYnamic MOdeling software - MADYMO. The fundamental characteristics of the vehicle and guideway are obtained from detailed finite element analyses using MSC-NASTRAN. As a result, the vehicle is modeled in MADYMO as a 21- degree-of-freedom spring-mass-damper system. A three span concrete guideway is modeled using 3D solid Hex8 elements. The air gap is modeled as a penetration of the magnets into the guideway. Decentralized colocated PD controllers are used for controlling the penetration of each …

Electroactive Polymers (Eap): Simulation Studies Of The Actuation Mechanisms In A Cantilever Cellulose Electroactive Paper, Fatim A. Mbaye

Electrical & Computer Engineering Theses & Dissertations

Electroactive polymers (EAPs) exhibit large strain in response to an external electric field and have attracted a great deal of attention in recent years for sensor and actuator applications. Favorable properties include soft actuation, ease and simplicity in manufacturing, being light-weight, low power consumption, and the ability to withstand harsh environments. However, this is an emerging material, and several aspects, including the fundamental mechanisms for piezoelectric deflections, remain unclear. This project studies the internal electromechanical factors that contribute to the voltage induced deflections of electro-active paper (EAPap). Experimental measurements of bias dependent deflections and water absorption as a function of …

Conceptual Mems Devices For A Redeployable Antenna, Virginia Miller

Theses and Dissertations

Micro-Electro-Mechanical Systems (MEMS) are becoming an integral part of our lives through a wide range of applications, including MEMS accelerators for air bag deployment in vehicles, micromirrors in projection devices, and various sensors for chemical/biological applications. MEMS are a key aspect of ever-increasing significance in a myriad of commercial and military applications. Because of this importance, this thesis utilizes MEMS devices that can deploy and retract an antenna suitably sized for placement on an insect or microrobot for communication purposes. A target monopole antenna with a length of 1 mm was used as a test metric. From this requirement, several …

Radio Frequency Mems Switch Contact Metal Selection, Ronald A. Coutu Jr., Paul E. Kladitis, Robert L. Crane, Kevin D. Leedy

AFIT Patents

A method for selecting metal alloys as the electric contact materials for microelectromechanical systems (MEMS) metal contact switches. This method includes a review of alloy experience, consideration of equilibrium binary alloy phase diagrams, obtaining thin film material properties and, based on a suitable model, predicting contact electrical resistance performance. After determination of a candidate alloy material, MEMS switches are conceptualized, fabricated and tested to validate the alloy selection methodology. Minimum average contact resistance values of 1.17 and 1.87 ohms are achieved for micro-switches with gold (Au) and gold-platinum (Au-(6.3 at %)Pt) alloy contacts. In addition, `hot-switched` life cycle test results …

A Study On The Application Of Thermoelectric Heat Pumps For Heating Applications, James Lincicome

Mechanical Engineering Undergraduate Honors Theses

Typically, thermoelectric heat pumps are used in cooling applications where space and portability are important, but they can be used efficiently in heating applications under the right conditions. This paper explains the origins of the thermoelectric heat pump, its applications in society, and the technical aspects of the device. The many different appurtenances that the device requires will be discussed along with their drawbacks. The single-stage data for the cells will be compared to the two-stage configuration data, and the data gathered for a specific thermoelectric device will be compared to the manufacturer's published data for the different configurations of …

Characterizationn Of Polumer-Based Mems Pyroelectic Infrared Detector, Mark E. Allard

Theses and Dissertations

AFRL/MLPJE had developed a novel thermal sensing material termed protein-impregnated-polymer (PIP). Thus far, a proof-of-concept has been demonstrated using a macro-sized pixel (0.64 mm²) as a bolometric detector. In an effort to better characterize this novel thermal sensing material, experimental data was used to determine figures of merit (FOMs) comparative to off-the-shelf thermal detectors. Microelectromechanical (MEMS) pixels were designed and used as the support structure for an inkjet-deposited droplet of the PIP. During the material characterization, two observations were made: PIP is a pyroelectric material, and the polymer (polyvinyl alcohol (PVA)) without the protein was found to be …

Toward A Flying Mems Robot, Nathan E. Glauvitz

Theses and Dissertations

The work in this thesis includes the design, modeling, and testing of motors and rotor blades to be used on a millimeter-scale helicopter style flying micro air vehicle (MAV). Three different types of motor designs were developed and tested, which included circular scratch drives, electrostatic motors, and comb drive resonators. Six different rotor designs were tested; five used residual stress while one design used photoresist to act as a hinge to achieve rotor blade deflection. Two key parameters of performance were used to evaluate the motor and rotor blade designs: the frequency of motor rotation and the angle of deflection …

Characterization Of Intercalated Graphite Fibers For Microelectromechanical Systems (Mems) Applications, Bryan W. Winningham

Theses and Dissertations

Research was accomplished to characterize the electrical and physical characteristic changes of the Thornel® P-100 carbon fiber and five variants when intercalated with 96% sulfuric acid and incorporated the use of Microelectromechanical Systems (MEMS) structures for testing purposes. The five fiber variants were oxidized in 1 M nitric acid at 0.5 A for 30 seconds, 1 and 2 minutes, the last two samples were detreated at 1150 °C for one hour prior to the nitric acid treatment. The fibers were mounted onto a MEMS die, placed into a chip carrier, sulfuric acid added, the chip carrier sealed and testing accomplished. …