Mechanical Engineering Commons^™

Direct Predictive Speed Control Of Salient Pmsm Drives In Constant Torque And Constant Power Regimes For Electric Vehicles Applications, Francis Mwasilu

Tanzania Journal of Engineering and Technology (TJET)

A direct speed control of salient permanent magnet synchronous motor (PMSM) drives in constant torque and constant power regimes for electric vehicles applications is presented. The proposed speed control scheme is derived from model predictive control approach where both rotor speed and stator current are formulated in a single objective function that is periodically computed to attain the PMSM drive optimum switching states. The dynamic model of the PMSM intrinsically encompasses the unknown disturbance, which should be rejected for high-performance speed control especially in transient conditions. Consequently, the extended modified augmented state Kalman filter (ASKF) is incorporated in the proposed …

Detection Of Nucleotides In Hydrated Ssdna Via 2-D H-Bn Nanopore With Ionic-Liquid/Salt-Water Interface, Jungsoo Lee

Multidisciplinary Studies Theses and Dissertations

Accomplishing slow translocation speed with high sensitivity has been the greatest mission for solid-state nanopore (SSN) to electrically detect nucleobases in single-stranded DNA (ssDNA). In this study, a method to detect nucleobases in ssDNA using a SSN is introduced by considerably slowing down the translocation speed and effectively increasing its sensitivity. The ultra-thin titanium dioxide (TiO₂) coated hexagonal boron nitride (h-BN) nanopore was fabricated, along with an ionic-liquid [bmim][PF₆]/2.0 M KCl aqueous (cis/trans) interfacial system, to increase both the spatial and the temporal resolutions. As the ssDNA molecules entered the nanopore, a …

Lead To Can Abrasion (Ltca) Test, Scott Mangin, Karthik Padmanabhan, Craig Icban

Mechanical Engineering

Pacemakers are medical devices which regulate a person’s heartbeat through electric pulses delivered via an endocardial lead attached to the heart. When a pacemaker is implanted in a patient, there is usually excess length left on the lead. Surgeons will typically wrap the excess lead length around the pacemaker device and close the wound. However, wrapping the lead around the pacemaker outer surface can open the lead to abrasion and cause the lead’s vital electrical insulation to be compromised. This is currently tested using an existing abrasion fixture at Abbott. However, the current tester does not yield consistent data results …

Machine Learning Augmentation Micro-Sensors For Smart Device Applications, Mohammad H. Hasan

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Novel smart technologies such as wearable devices and unconventional robotics have been enabled by advancements in semiconductor technologies, which have miniaturized the sizes of transistors and sensors. These technologies promise great improvements to public health. However, current computational paradigms are ill-suited for use in novel smart technologies as they fail to meet their strict power and size requirements. In this dissertation, we present two bio-inspired colocalized sensing-and-computing schemes performed at the sensor level: continuous-time recurrent neural networks (CTRNNs) and reservoir computers (RCs). These schemes arise from the nonlinear dynamics of micro-electro-mechanical systems (MEMS), which facilitates computing, and the inherent ability …

Telescope Parallel Actuator Mount: Control And Testing, Samuel S. Artho-Bentz

Master's Theses

This thesis approaches the task of designing a control system for the Parallel Actuator Mount developed by Dr. John Ridgely and Mr. Garrett Gudgel. It aims to create a base framework that directly controls the telescope and can be expanded to accept external command. It incorporates lower priced components and develops more easily approachable software with great functionality. An open-loop method for velocity control is established. Developing repeatable tests is a major focus. Testing finds the control methods developed result in velocity error of less than 5% and position error of less than 1.5% despite several mechanical issues and inaccuracies. …

2 Degree Of Freedom Robotic Leg, Oded Tzori, Henry Terrell, Adan Martinez

Mechanical Engineering

Professor Xing, an assistant professor at Cal Poly, proposed the 2 DOF Robotic Leg project for this quarter’s senior project class. The project is to build a robotic leg attached at the hip to a stand, which will be used as a teaching tool and eventually help develop Cal Poly’s very own robotic quadruped. Since this project has multiple uses after its completion, there are multiple customers that it must perform well for: the Cal Poly Mechanical Engineering (ME) Department, the ME Lab instructors, and the students. The Scope of Work (Sections 2 & 3) is composed of 2 main …

Deep-Sea Water Collector, Chandler Jones, Jenny Verheul, Michael Di Giorgio

Mechanical Engineering

Properties such as nutrients, DNA, pH levels, and primary productivity are difficult to measure onboard an Underwater Remotely Operated Vehicle (UROV) as mobile submarine sensors are highly expensive and conventional water capture devices are too large to be equipped. However, these properties provide an integral view into our oceans, the species that inhabit them, and our influence on the environment. Collected samples of seawater taken back to labs allow researchers to see a clearer picture of ecosystems’ inhabitants and lifecycle with the analysis of Environmental DNA (eDNA) among many other properties. The scope of this project is to design a …

A Quantitative Approach For Tuning A Mountain Bike Suspension, Steven Robert Waal

Master's Theses

A method for tuning the spring rate and damping rate of a mountain bike suspension based on a data-driven procedure is presented. The design and development of a custom data acquisition system, known as the "MTB DAQ," capable of measuring acceleration data at the front and rear axles of a bike are discussed. These data are input into a model that is used to calculate the vertical acceleration and pitching angular acceleration response of the bike and rider. All geometric and dynamic properties of the bike and rider system are measured and built into the model. The model is tested …

Resistive Switching In Fto/Cuo-Cu2o/Au Memory Devices, Amir Shariffar, Haider Salman, Tanveer A. Siddique, Wafaa Gebril, M. Omar Manasreh

Electrical Engineering Faculty Publications and Presentations

Memristors are considered to be next-generation non-volatile memory devices owing to their fast switching and low power consumption. Metal oxide memristors have been extensively investigated and reported to be promising devices, although they still suffer from poor stability and laborious fabrication process. Herein, we report a stable and power-efficient memristor with novel heterogenous electrodes structure and facile fabrication based on CuO-Cu2O complex thin films. The proposed structure of the memristor contains an active complex layer of cupric oxide (CuO) and cuprous oxide (Cu2O) sandwiched between fluorine-doped tin oxide (FTO) and gold (Au) electrodes. The fabricated memristors demonstrate bipolar resistive switching …

Dynamics Analysis Of Misalignment And Stator Short-Circuit Coupling Fault In Electric Vehicle Range Extender, Xiaowei Xu, Jingyi Feng, Nan Zhang, Xiaoqing Wang

Research, Publications & Creative Work

Due to the complex structure and wide excitation of the range extender, the misalignment and stator short-circuit coupling fault can easily occur. Therefore, it is necessary to study the coupling fault mechanism of the range extender, analyze the cause of the fault and the fault evolution law, and research the coupling fault characteristics. To reveal the mechanism of misalignment and stator-short-circuit coupling fault, the misalignment mechanism was analyzed and the bending and torsion electromagnetic stiness of the generator in the stator short-circuit fault was derived. Then the dynamic model of bending and torsion coupling for the generator was established. Furthermore, …

Dynamic Analysis And Fabrication Of A Bi-Stable Structure Designed For Mems Energy Harvesting Applications., Masoud Derakhshani

Electronic Theses and Dissertations

Thanks to the rapid growth in demand for power in remote locations, scientists’ attention has been drawn to vibration energy harvesting as an alternative to batteries. Over the past ten years, the energy harvesting community has focused on bistable structures as a means of broadening the working frequency range and, by extension, the effective efficiency of vibration-based power scavenging systems. In the current study, a new method is implemented to statically and dynamically analyze a bistable buckled, multi-component coupled structure designed specifically for low-frequency vibration energy harvesting systems in both macro and MEMS-scale sizes. Furthermore, several micro-fabrication steps using advanced …

Multiphysics Finite Element Analysis Of In-Pile Sensors For Advanced Nuclear Reactors, Takoda Linn Bingham

Boise State University Theses and Dissertations

Nuclear reactors have large needs for in-pile sensors that are durable in high temperature, radioactive, and corrosive environments. With the use of multiphysics finite element analysis (FEA) researchers can speed up sensor prototyping. FEA also allows for a better fundamental understanding of sensors and enables sensor optimization. This research focuses on three types of in-pile sensors developed at Idaho National Laboratory: acoustic sensors, linear variable differential transformers (LVDT), and capacitance based strain gauges (CSG). Two acoustic sensors, magnetostrictive waveguides and piezoelectric surface acoustic wave (SAW) sensors were first modeled. These models showed the acoustic wave patterns and estimated the speed …

Low-Cost Reaction Wheel Design For Cubesat Applications, Nicholas J. Bonafede Jr.

Master's Theses

As science instruments on CubeSats become more sensitive to the attitude of the spacecraft, better methods must be employed to provide the accuracy needed to complete the planned mission. While systems that provide the accuracy required are available commercially, these solutions are not cost-effective, do not allow the design to be tailored to a specific mission, and most importantly, do not give students hand-on experience with attitude control actuators. This thesis documents the design, modeling, and simulation of a low-cost, student-fabricated, reaction wheel system for use in 3U CubeSat satellites. The entire design process for the development of this reaction …

Experimental Investigation Of The Wind Energy Harvesting Potential Of A Stand-Alone Piezoelectric Strip, Phillip Christopher Scott

Mechanical Engineering ETDs

The purpose of the study was to investigate the feasibility of harvesting wind energy on a small scale in residential areas. The method investigated was the initiation of movement-induced excitation (MIE), a type of aeroelastic flutter, within samples of polyvinylidine fluoride (PVDF), a piezoelectric polymer. Single samples of PVDF were secured in a wind tunnel and sample voltage was measured over a broad range of wind speeds. Power was calculated then via the addition of ohmic resistance matched to the magnitude of the capacitive impedances of the samples. The geometry of the PVDF samples studied was maintained as a simple …

Study On The Chemical And Mechanical Stability Of Polymer Nanofluidic Biosensors, Dae Won Kim

LSU Master's Theses

Polymer nanofluidic devices have great potential to replace silicon (Si) and glass-based nanofluidic devices in biomedical applications due to their advantages such as low material and fabrication cost, various physicochemical properties, well-developed surface modification protocol, and low electrical noises for electrical measurements. In nanofluidic sensing applications, single molecules such as DNA are introduced into the fabricated nanochannel or nanopore, measuring their physicochemical properties optically or electrically. The properties of materials for nanofluidic devices have a significant role in the performance of the devices, such as DNA translocation and device stability.

Among several nanoscale fluidic physics, surface charge density is a …

Towards A Cyber-Physical Manufacturing Cloud Through Operable Digital Twins And Virtual Production Lines, Md Rakib Shahriar

Graduate Theses and Dissertations

In last decade, the paradigm of Cyber-Physical Systems (CPS) has integrated industrial manufacturing systems with Cloud Computing technologies for Cloud Manufacturing. Up to 2015, there were many CPS-based manufacturing systems that collected real-time machining data to perform remote monitoring, prognostics and health management, and predictive maintenance. However, these CPS-integrated and network ready machines were not directly connected to the elements of Cloud Manufacturing and required human-in-the-loop. Addressing this gap, we introduced a new paradigm of Cyber-Physical Manufacturing Cloud (CPMC) that bridges a gap between physical machines and virtual space in 2017. CPMC virtualizes machine tools in cloud through web services …

Performance Analysis Of Renewable Energy Resources In Rural Areas: A Case Study Of Solar Energy, Jackson Justo

Tanzania Journal of Engineering and Technology (TJET)

This paper presents an overview of the recent development trends of solar photovoltaic (PV) systems and the performance in the Tanzanian context. The two types of solar power generation that are considered in this paper are: i) solar PV systems and ii) concentrated solar power (CSP). The two are compared in terms of cost of energy and energy storage mechanism. Moreover, the effect of ambient temperature on the solar PV module is analyzed. In addition, a detailed analysis on using solar axis tracking to increase the power generation is also presented. The extent to which the cell surface temperature and …

Polyimide/Silicon Dioxide Nanocomposites As Dielectrics For Helium-Cooled High-Temperature Superconducting Cables, Harrison Michael Hones

Theses and Dissertations

In this thesis, polyimide (PI) and silicon dioxide (SiO2) were combined in the form of a nanocomposite for use as a dielectric on helium-cooled high-temperature superconducting (HTS) cables. Further, a cryogenic chamber was designed with the intent of cooling samples to 40 K for dielectric and thermal contraction testing. Composites were created through an in situ process which resulted in nanoparticle formation within the host matrix. Samples were tested for dielectric strength at room temperature (300 K) as well as cryogenic temperature (92 K) using liquid nitrogen as the coolant. Composite samples tested at 300 K averaged a dielectric strength …

Feasibility Of Electric Field Assisted Clogging Reduction In Cold Gas Spraying Nozzle, Hendric Tronsson

ENGS 88 Honors Thesis (AB Students)

The relatively novel cold spraying process expands its range of applications constantly. In order to continue this trend, this process still has various hurdles that need to be overcome such as clogging. Clogging within the cold gas spraying process causes porous coatings with less material properties and lower durability; a solution is needed in order to reduce the clogging and so expand the cold gas spraying applications. This study aimed to explore the feasibility of using an electric field to reduce clogging. To do so a simplified channel was used to simulate charged particle trajectory shifts under the influence of …

Pier Portal, Alec W. Hardy

Master's Theses

The Pier Portal marine monitoring system is an internet controlled underwater camera that will enable students, researchers, and the general public the ability to monitor underwater marine life and ocean conditions. Installed at Cal Poly’s Center for Coastal Marine Science pier at Avila Beach, California, the camera can be commanded in real-time to raise or lower to any position between the top of the pier and the bottom of the ocean floor, while providing a live-stream video to the operator and general public. This thesis effort focused on the integration of the various subsystem components through software, and the development …

Surface Autonomous Vehicle For Emergency Rescue, Max Emerick, Ryan Shields, Christopher Feickert, Raymond Impara

Mechanical Engineering

The goal of this document is to clearly define the problem parameters and project objectives and to clearly describe the design process, planned final design, and manufacturing and testing procedures for the senior design project of Team 26: SAVER -- the Surface Autonomous Vehicle for Emergency Rescue. This is both for the purpose of project planning and for clear communication between all parties involved in the project.

The objective of the SAVER project is to develop a proof of concept for an autonomous maritime search and rescue vehicle for aiding in man-overboard missions. To accomplish this goal, a list of …

Mug For Tremors, Logan J. Smith, Allen Tecson, Jaret Wedow, Kai Workman

Mechanical Engineering

Melissa Oliver, an occupational therapist at McGuire VA Medical Center, works extensively with veterans who struggle with certain daily activities due to their hand tremors. Hand tremors caused by essential tremor, Parkinson’s Disease, or other physical or neurological impairments can greatly affect an individual’s ability to perform daily tasks. One of these tasks include the ability to handle beverages, as hand tremors can cause excessive sloshing and spilling of liquid. Melissa reached out to find a way to help veterans with hand tremors easily consume liquids. Our team, consisting of Logan Smith, Allen Tecson, Jaret Wedow, and Kai Workman, was …

Electromagnetic Actuator For Camless Engines, Nicholas Olesh, Charlie Thomas Glenwright, Tim Wills De Tone, Darya Daniel Darvish

Mechanical Engineering

This document summarizes the research, objectives, project plan, and design for developing an electromagnetic actuator valve for use in a camless internal combustion engine. While electromagnetic valve actuators have not been implemented into a working product to date, there have been many attempts to research and develop working prototypes. Similar products have been developed, but they do not use purely electromagnetic actuation. This research is significant because it shows the challenge that must be overcome and outlines potential design solutions to the problem. The objectives section highlights the problem statement and what is aimed to be achieved in this project. …

Optical Filter Selector, Camaryn Chambers, Joel Pitzer, Matthew Allen, Callen Schwefler

Mechanical Engineering

One of the many challenges with launching projectiles into space is predicting how the environment in space will affect the trajectory. One way to do this is to look at optical emissions, also known as airglow, which can only be seen from earth with sensitive equipment. By taking measurements of the light from the airglow, properties about the upper atmosphere can be inferred. This is important because variability in the atmosphere can cause variability in space that can affect astronauts and satellites. In order to accomplish this task, optical filters must be used to observe different bands of wavelengths of …

Sub-Lunar Tap-Yielding Explorer, Styx, Alexander J. Krenitsky, Ryan J. Locatelli, Aaron B. Erickson, Christoopher B. Boone, Westin R. Mchaney

Mechanical Engineering

To diversify the idea pool that NASA has to draw from for future manned and unmanned missions to the Moon and Mars, a design/build competition has been posed to collegiate teams across the country. The challenge is to reach, extract, and purify underground ice reserves in a setting analogous to mars. Along the way, teams will be collecting telemetry to mimic prospecting objectives on the moon.

The Sublunar Tap-Yielding eXplorer, STYX, is the team’s proposed design for the 2020 NASA RASC-AL competition. Some novel design features STYX will use are a rotary tool changer with swappable tools, a sleeve driving …

Control And Locomotion Of Inertially And Magnetically Actuated Multi-Scale Robotic Systems, Ehab Al Khatib

Mechanical Engineering Research Theses and Dissertations

In this research, two actuation systems were introduced, inertial and magnetic actuation. In the inertial actuation, the robot used the transfer of momentum to navigate, and this momentum could be generated by spinning masses and wheels. Recent studies in our System Laboratory proved that a wide range of inertially actuated locomotion systems could be generated. This can be achieved by using a family tree approach, starting from a very simple system, and progressively evolving it to more complex ones. The motion diversity of these robots inspired us to extend their locomotion from a macro scale to millimeter and micro scales. …

Impact Of Magnetocaloric Material Properties On Performance Of A Magnetocaloric Heat Pump., Michael G. Schroeder

Electronic Theses and Dissertations

In the field of magnetocaloric heat pumps much research has been performed around machine design and theoretical machines, but little has been researched around practical problems such as variability in material properties. The present work defines a simulation tool that has been proven with experimental data. Magnetocaloric material cascades were statistically analyzed and parameterized, such that they could be recreated parametrically using a split Lorentz function with normally distributed parameters. Correlated curve-defining values with standard deviations were used as input into the simulation tool to determine the effect of variation on cooling heat pump performance for a household refrigerator application. …

Advanced Mechatronics, Hao Su

Open Educational Resources

Project-based course on the design of mechatronic devices to address needs identified by hospital-based clinicians and industry. Students work in teams to develop a mechatronic prototype. The lectures will cover the design of medical devices and robotics including sensors, actuators, and robots. The students will communicate with customers to understand design needs, then conduct study on prior art, intellectual property, due diligence, and idea conceptualization. Students will present ideas in class and to a broad audience from local industry. Students will also write a publication-quality final report, which they will be encouraged for publication submission.

Engineering Design I, Hao Su

Open Educational Resources

Introduction to robotics

Stability Analysis, Dynamic Modeling, And Kinematic Analysis Of Hydraulically Amplified Dielectric Elastomer Actuators And Robot Manipulators, Amir Hosein Zamanian

Mechanical Engineering Research Theses and Dissertations

In this dissertation, we have proposed a new dielectric elastomer actuator design and model that couples electrostatics, fluid mechanics, linear and nonlinear elastic deformations. The internal hydraulic pressure can amplify the structural deformation generated by induced electrostatic forces (Maxwell pressure), given the name of this class of actuators, hydraulically amplified dielectric elastomer actuators (HADEAs).

First, we developed novel lumped-parameter models (LPMs) using linear and hyper-elastic material models and second compared the LPM results with finite element analysis in quasi-static simulations. We analytically expressed the conditions for the snap-through instability in the HADEA, which appears after exceeding a certain voltage applied …