Mechanical Engineering Commons^™

Analysis Of Vibration Generated By The Rubbing Of Flat Surfaces, Zahrul Fuadi

Makara Journal of Technology

Among the phenomena that occur as a result of contact between two surfaces is friction sound, in which surface roughness is of great importance. In this study, the parameter of contact stiffness is used to explain the frequency characteristic of vibration generated by the rubbing of flat surfaces under a small load. A 3-disk configuration rubbing method was used, which provides a unique characteristic of the system's frequency response function containing specific information about the rubbing vibrations. It is shown that the peak frequency of the rubbing vibration can be explained by using a two-degrees-of-freedom model incorporating the parameter of …

Endoscopic Application Of A Compact Compound-Eye Camera, Keiichiro Kagawa, Shoji Kawahito

Makara Journal of Technology

A multi-functional compound-eye endoscope enabling multi-spectral imaging and variable field-of-view is presented, which is based on a compact compound-eye camera called TOMBO (thin observation module by bound optics). Narrow-band filters attached to some lenses provide snap-shot multi-band images. Fixed and movable mirrors are introduced to control the field of view, which realizes several observation modes such as three-dimensional shape measurement, wide field-of-view, and close-up observation.

Development Of The Soekarno–Hatta International Airport Rail Link Project Using The Value Engineering Method: Creating Value For Money, Mohammed Ali Berawi, Bambang Susantono, Suyono Dikun, Tommy Ilyas, Herawati Zetha Rahman, Abdur Rohim Boy Berawi, Teuku Yuri Zagloel, Perdana Miraj, Jade Sjafrecia Petroceany

Makara Journal of Technology

Soekarno–Hatta Airport is the main gateway for international flights to Greater Jakarta. Its accessibility depends on the inter-city and Sedyatmo toll roads, which causes congestion in peak hours, leading to uncertainty about travel times. The Soekarno–Hatta International Airport Rail Link (SHIARL) is proposed as an alternative mass transportation project, which is expected to provide accessibility and mobility for people and goods to and from the airport. Previously, the project was unattractive to private investors as it was technically and financially unfeasible. Therefore, this research aims to improve the feasibility of the Soekarno-Hatta International Airport Rail Link (SHIARL) by using a …

The Mechanical And Tribology Properties Of Sputtered Titanium Aluminum Nitride Coating On The Tungsten Carbide Insert Tool In The Dry Turning Of Tool Steel, Esmar Budi, Mohd. Razali Bin Muhamad, Md. Nizam Bin Abdul Rahman

Makara Journal of Technology

The effect of the sputtering parameters on the mechanical tribology properties of Titanium Aluminum Nitride coating on the tungsten cabide insert tool in the dry turning of tool steel has been investigated. The coating was deposited using a Direct Current magnetron sputtering system with various substrate biases (-79 to -221 V) and nitrogen flow rates (30 to 72 sccm). The dry turning test was carried out on a Computer Numeric Code machine using an optimum cutting parameter setting. The results show that the lowest flank wear (~0.4 mm) was achieved using a Titanium Aluminum Nitride-coated tool that was deposited at …

Modified Design Of Pin-On-Ring Tribometer For Hip Joint Prostheses Measurement; Case Study On Salat Activity, Muhammad Khafidh, Jamari Jamari, Sulardjaka Sulardjaka, Mohamad Tauviqirrahman, Emile Van Der Heide

Makara Journal of Technology

Total hip replacement (THR) is one of the most successful orthopedic surgical procedures for replacing a broken hip joint. In THR, wear may occur at the articulating surface of the acetabular cup and the femoral head. In Indonesia, the country with the largest Muslim population in the world, most of the inhabitants do salat (praying) every day. THR users are banned from doing salat for fear it will damage the hip joint prostheses. The previous wear calculation methods on the hip joint prostheses use the gravimetric, coordinate measuring machine (CMM), profiler, and geometric method. The disadvantages of the previous methods …

Continuous Production Of Nanotubes And Carbon Clusters By Use Of The Revolver-Injection-Type Arc Jet Producer, Tetsu Mieno, Naoki Matsumoto, Takahashi Tomie, H. Inoue

Makara Journal of Technology

Efficient and continuous production of fullerenes, single-walled carbon nanotubes (SWNTs), and carbon nano-particles has been developed by the JxB arc jet method, where the Lorentz force of magnetic field jets out gaseous carbon particles to the JxB direction. In order to realize continuous mass production of these carbon clusters, the revolverinjection- type arc jet producer (RIT-AJP) has been developed. Production of fullerenes, endohedral metallo-fullerenes, SWNTs, metal-encapsulated carbon nano particles has been examined.

Lateral Load Resistance Of Laminated Veneer Lumber Sengonwooden Joints With Wooden Dowels, Niken Palaeowati, Ali Awaludin, Suprapto Siswosukarto

Makara Journal of Technology

Analytical models for wooden-doweled joints need to be developed. The objective of this research is to determine whether the strength of wooden-doweled joints can be well predicted by equations developed for steel-doweled joints. In this experiment, various connection parameters, such as dowel diameter, species of the wooden dowel, and angle of joints, are studied. The joint specimens are loaded in a quasi-static state with four replications each. A5% offset diameter method is used to determine the lateral load resistance of the tested joints, while the predictions are evaluated by equations given in Indonesian National Standard (SNI) 7973-2013 and the European …

Design, Analysis And Implementation Of An Experimental System To Harvest Energy From Atmospheric Temperature Variations Using Ethyl Chloride Filled Bellows, Gibran Ali

All Theses

The increase in global warming and the dwindling supplies of fossil fuels have shifted the focus from traditional to alternate sources of energy. This has resulted in a concerted effort towards finding new energy sources as well as better understanding traditional renewable energy sources such as wind and solar power. In addition to the shift in focus towards alternate energy, the last two decades have offered a dramatic rise in the use of digital technologies such as wireless sensor networks that require small but isolated power supplies. Energy harvesting, a method to gather energy from ambient sources including sunlight, vibrations, …

Mega: An Energy Aware Algorithm For Self-Powered Wireless Sensor Networks In Sustainable Smart Infrastructure, Dong Qi, Yu Chen, Shahrzad Towfighian

Mechanical Engineering Faculty Scholarship

Smart infrastructure is attractive for possessing many desirable features, such as uninterrupted monitoring of health conditions, timely response to damages, and human-infrastructure interactions. Embedded sensors that collectinformation are critical for decision making. However, the lifetime of electronic sensors is a constraint to infrastructure lifetime if sensors are physically embedded in the infrastructure at construction time. In this paper, we studied a self-powered wireless sensor network that harvests energy from mechan-ical vibration in the environment. A dynamic, hierarchical algorithm called MEGA is proposed that constructs clusters and elects the cluster head based on residue energy and energy harvest rate. Taking a …

Numerical Simulation Of The Heat Leakage At The Gasket Region Of Domestic Refrigerators, Feng Gao

All Theses

Computational Fluid Dynamics (CFD) simulations are performed to investigate the heat loss at the gasket of a standard over/under domestic refrigerator. The study numerically simulates a unique experimental test cell with only the gasket region exposed to the ambient environment and other parts protected by insulation (see picture below). The test cell is cubic with an interior cavity having dimensions 2' x 2' x 2' within which a heating element is placed to create a specified temperature difference. A matching set of door and side panels exposes a 2' width of the gasket region to heat transfer with the surroundings. …

Induction Of Differentiation Of Dental Pulp-Derived Mesenchymal Stem Cells (Dpsc), Aubrey Young

UNLV Theses, Dissertations, Professional Papers, and Capstones

Mesenchymal stem cells are derived from a variety of human tissues and are being bioengineered and studied for possible uses in the advancement of medicine. Recent efforts are being focused on Dental Pulp Stem Cells (DPSC's) due to the accessibility of this tissue. Many factors influence DPSC quality and quantity, including the specific methods used to isolate, collect, concentrate, and store these isolates once they are removed. Ancillary factors, such as the choice of media, the selection of early versus late passage cells, and cryopreservation techniques may also influence the differentiation potential and proliferative capacity of DPSC isolates.

The objective …

Applied Energy Systems - Rudimentary Thermodynamics, Jim Mcgovern

Book/Book Chapters

This is a compact textbook for a module addressing rudimentary thermodynamics within the context of applied energy systems. It is at an introductory level for engineers or technologists. The book does not attempt to cover the principles of thermodynamics comprehensively. Rather, it provides a practical but theoretically sound foundation, linked to some key areas. Energy, heat and work are all introduced, as are units and dimensions. Ideal gases and properties of liquids and vapours are treated. Non-flow and steady flow processes are described. Simple theory is provided for pumps and for the reciprocating compressor. Rudimentary steam and refrigeration or heat …

Improved Microrobotic Control Through Image Processing And Automated Hardware Interfacing, Archit R. Aggarwal, Wuming Jing, David J. Cappelleri

The Summer Undergraduate Research Fellowship (SURF) Symposium

Untethered submilliliter-sized robots (microrobots) are showing potential use in different industrial, manufacturing and medical applications. A particular type of these microrobots, magnetic robots, have shown improved performance in power and control capabilities compared to the other thermal and electrostatic based robots. However, the magnetic robot designs have not been assessed in a robust manner to understand the degree of control in different environments and their application feasibility. This research project seeks to develop a custom control software interface to provide a holistic tool for researchers to evaluate the microrobotic performance through advance control features. The software deliverable involved two main …

Adjustable Resonance Frequency Of Rf-Mems Capacitor By Using Comb- Drive Actuators: A Design Approaches, Agus Santoso Tamsir, Sandy Tannu Wijaya, Dato’ Burhanuddin Yeop Majlis

Makara Journal of Technology

The needs of smaller size RF varactor is a must today, and MEMS comes to be the potential one. In this paper we proposed an adjustable resonance RF-MEMS varactor by using comb-drive actuators placing in each side of the square movable plate. In our preliminary simulation, we found that the device can work properly but some constraints comes such as the dominancies of harmonic resonance frequencies that influences into the nominal capacitances. Therefore for the next step of development we have to find out the window of the structural dimension for a certain spans and a certain operating frequencies.

Make Or Buy Analysis Model Based On Tolerance Design To Minimize Manufacturing Cost And Quality Loss, Cucuk Nur Rosyidi, Reza Rizkichani Akbar, Wakhid Ahmad Jauhari

Makara Journal of Technology

In a manufacturing company, manufacturing costs, or component prices, and tolerance will affect the price and the quality of a product. Companies must produce high-quality products with low manufacturing costs in order to keep their products competitive in the market; however, it is difficult to produce a high-quality product with a low manufacturing cost. Companies have difficulties in determining the components to be produced using their own manufacturing facilities (make) or outsourced to their suppliers (buy). Hence, a make or buy analysis is needed to minimize the manufacturing costs and quality loss and to determine the optimum alternative regarding make …

Observation Of Tunneling Effects In Lateral Nanowire Pn Junctions, Sri Purwiyanti, Arief Udhiarto, Daniel Moraru, Takeshi Mizuno, Djoko Hartanto, Michiharu Tabe

Makara Journal of Technology

As electronic device dimensions are continuously reduced, applied bias conditions significantly change and the transport mechanisms must be reconsidered. Tunneling devices are promising for scaled-down electronics because of expected high-speed operation and relatively low bias. In this work, we investigated the tunneling features in silicon-oninsulator lateral nanowire pn junction and pin junction devices. By controlling the substrate voltage, tunneling features can be observed in the electrical characteristics. We found that the minimum substrate voltage required for tunneling to occur in pn junctions is higher as compared with pin junctions. The main cause of these effects relies in the difference between …

Argon Ion Irradiation Effect On The Magnetic Properties Of Fe-Al2o3 Nano Granular Film, Setyo Purwanto, Isao Sakamoto

Makara Journal of Technology

We studied the effect of Argon (Ar) ion irradiation on Fe-Al2O3 nanogranular thin film. X-ray diffraction (XRD) patterns show that the ion dose might promote the growth of the Fe2O3 phase from an amorphous phase to a crystalline phase. The magnetic and magnetoresistance properties were investigated using a vibrating sample magnetometer (VSM) and a four point probe (FPP). The results suggest that percolation concentration occurred at the 0.55 Fe volume fraction and with a maximum magnetoresistance (MR) ratio of 3%. The present MR ratio was lower than that of previous results, which might be related to the existence of the …

Digestibility Of Betung Bamboo Fiber Following Fungal Pretreatment, Widya Fatriasari, Wasrin Syafii, Nyoman J. Wistara, Khaswar Syamsu, Bambang Prasetya

Makara Journal of Technology

This research evaluated the effect of fungal pretreatment of betung bamboo fibers and enzymatic- and microwaveassisted hydrolysis on the reducing sugar yield. The enzymatic hydrolysis of the pretreated biomass was carried out with cellulase and 10 and 20 FPU/g of substrate in a shaking incubator at 50 °C and 150 rpm for 48 h. The sulfuric acid concentration used in the microwave-assisted acid hydrolysis was 1.0, 2.5, and 5%, either with or without the addition of activated carbon. Microwave irradiation (330 Watt) was applied for 5–12.5 min. The yield of reducing sugar was better with the microwave-assisted acid hydrolysis, and …

Electron Emission Characteristics Of Multi-Gated Field Emitters, Hidenori Mimura, Yoichiro Neo, Toru Aoki, Tomoya Yoshida, Masayoshi Nagao

Makara Journal of Technology

We have developed a multi-gated field emitter (FE) such as a quadruple-gated FE with a three-stacked electrode lens and a quintuple-gated FE with a four-stacked electrode lens. Both the FEs can focus the electron beam. However, the quintuple-gated FE has a stronger electron convergence than the quadruple-gated FE, and a beam crossover is clearly observed for the quintuple-gated FE.

Properties Of Lignin From Oil Palm Empty Fruit Bunch And Its Application For Plywood Adhesive, Lucky Risanto, Euis Hermiati, Yanni Sudiyani

Makara Journal of Technology

Lignin from lignocellulosic biomass is a potential biopolymer for wood adhesive. The aims of this study were to characterize lignin isolated from the black liquor of oil palm empty fruit bunch fiber pretreated with steam explosion in alkaline conditions and to examine the bond quality of aqueous polymer isocyanate (API) adhesive prepared from lignin, natural rubber latex (NRL), and polyvinyl alcohol (PVA) as base polymers with isocyanate crosslinkers. Lignin was precipitated from the black liquor by adding hydrochloric acid; then the precipitate was separated by filtration, thoroughly washed with water up to pH 2 and pH 5, and dried. The …

The Gaussian Orthogonal Laplacianfaces Modelling In Feature Space For Facial Image Recognition, Arif Muntasa

Makara Journal of Technology

Dimensionality reduction based on appearance has been interesting issue on the face image research fields. Eigenface and Fisherface are linear techniques based on full spectral features, for both Eigenface and Fisherface produce global manifold structure. Inability of them in yielding local manifold structure have been solved by Laplacianfaces and further improved by Orthogonal Laplacianfaces, so it can yield orthogonal feature vectors. However, they have also a weakness, when training set samples have non-linear distribution. To overcome this weakness, feature extraction through data mapping from input to feature space using Gaussian kernel function is proposed. To avoid singularity, the Eigenface decomposition …

Series-Interconnected Plastic Dye-Sensitized Solar Cells Prepared By Low- Temperature Binder-Free Titania Paste, Erlyta Septa Rosa, Lia Muliani, Shobih Shobih, Jojo Hidayat, Brian Yuliarto

Makara Journal of Technology

The aim of this research is to study dye-sensitized solar cells (DSSC). This was implemented on a flexible polyethylene terephthalate (PET) substrate using a mixture of transparent and scattered mesoporous anatase-titania as the electron transport layer for the photoelectrode. This mixture of anatase titania performed a dual function of light scattering and efficient dye absorption. In this study, a porous nano-TiO2 film was prepared on indium tin oxide (ITO) coated polyethylene terephthalate (PET) by using a binder-free titania paste; on it, a DSSC was fabricated. The paste which contained a mixture of TiO2 nanoparticles, acid chloride, and ethanol was printed …

Foss Big Data Storage Solution, Nurdeen Salami

STAR Program Research Presentations

NASA projects require a reliable approach to store large volumes of data. Accordingly, it is crucial to adopt a lightweight, reliable, and scalable database. Current NASA databases bear costly license fees with undesirable speed and flexibility. The purpose of utilizing the AERO Institute as an IT test bed, or “Sandbox,” is to design, build, test, and implement software solutions prior to transfer to NASA projects. Cassandra coupled with the Astyanax API is a viable solution for storing big data. Store a minimum of 2GB of C-FOSS data in multiple file formats (.csv, .log, .xml, and .jpg). Use benchmark tests to …

Space Race: Capturing An Orbiting Sample And A Nation’S Imagination, Stephanie La Liberte, Andrew Chavarin, Shubham Gogna, C. Daniel Thomas, Vy Phung, Gabriel Udomkesmalee

STAR Program Research Presentations

A proposed architecture for future planetary sample return missions would consist of capturing on-orbit a sample container (collected from the surface of a planetary body and launched into space) and transferring the sample container into an earth return/reentry capsule. A challenge to this proposed architecture is integrating space applicable sensor technologies with sufficient capturing devices. While useful technologies on Earth, Earth-related rendezvous/capture technologies, such as magnetic field sensors, sound-based sensors, and Earth orbit-based radios like GPS, are not applicable to space. Inspired by the in-orbit sample capture challenge, NASA JPL has designed the Space Rendezvous And Capture Experiment (Space RACE). …

Electroencephalography(Eeg) Data Collection And Processing Through Machine Learning, Jayshree Desai

Graduate Theses and Dissertations

Machine learning methods are an excellent way for understanding the neural basis of human decision making. Some machine learning systems try to eradicate the need for human intuition in data analysis whereas others embrace a collective approach between humans and machines. The objective of this project is to collect Electroencephalography (EEG) signals through wireless sensors, and the process the collected signals through machine learning methods. The EEG data is collected using three EEG electrodes, each being the positive, negative and ground terminals respectively. Since the signal measures in the unit of micro-volts it needs to be amplified using amplifier circuit. …

Cfd Simulation Of The Thermal Performance Of A Parallel Counter-Parallel Flow Heat Exchanger For The Treatment Of Hypothermia, Alex Heller

UNLV Theses, Dissertations, Professional Papers, and Capstones

Hypothermia is a life-threatening condition. Currently, active warming methods are the most effective treatment for dysthermic patients. The aim of this study is to investigate the use of computational fluid dynamics (CFD) in evaluating the thermal performance of a parallel/counter-parallel flow heat exchanger used as part of a fluid warmer to treat Hypothermia. The 3D model of the heat exchanger is divided into three regions; Infusate (fluid to be heated), Hot Water (heating fluid), and a Solid Region (wall). At the end of the heat exchanger, an elbow section is used to create the counter-parallel flow arrangement specific to this …

Development Of A Black-Box Transient Thermal Model For Residential Buildings, Andrew Cross

UNLV Theses, Dissertations, Professional Papers, and Capstones

Heavily populated metropolitan areas located in cooling-dominated climates, as are found in the Desert Southwest, pose a challenge to electrical utilities that service these areas. During the late afternoons of the summer months, residents of these metropolitan areas require larger than normal amounts of power to run their homes' air conditioning systems, at significant expense to the utilities. In the study reported here, interior temperature and power consumption data, accumulated over the course of a year and a half from seven houses within a Las Vegas neighborhood, are used to develop a predictive black-box statistical model for residential thermal transience. …

Acoustic Testing Of Generator/Alternator Fans, Jacob Kriesel

Culminating Projects in Electrical Engineering

The intent of this project was to fill in a gap of the testing knowledge possessed for acoustics of an alternator within a generator set. The objective was to build a test fixture that would allow the user to test the acoustics of alternators without the driving force of an engine, which is a high acoustic source during testing. Eliminating the engine from the equation would allow for more accurate data of the product line, allowing for better utilization of acoustic tools when implementing sound source dampening. At the end of the project, it was found that the test fixture …

Integration Of Microwave And Thermographic Ndt Methods For Corrosion Detection, Dustin F. Pieper, Kristen M. Donnell, Mohammad Tayeb Ahmad Ghasr, Edward C. Kinzel

Electrical and Computer Engineering Faculty Research & Creative Works

Infrastructure health monitoring is an important issue in the transportation industry. For the case of cement-based structures in particular, detection of corrosion on reinforcing steel bars (rebar) is an ongoing problem for aging infrastructure. There have been a number of techniques that have shown promise in this area including microwave nondestructive testing (NDT) and thermography. Thermography is quite advantageous as it is an established method, and can be utilized for large inspection areas with intuitive results. Typical heat sources include induction heating and flash lamps, but these are not without drawbacks. Microwave nondestructive testing has also been successful at detecting …

Integration And Implementation Of High-Voltage Energy Storage Sub-System For A Parallel-Through-The-Road Plug-In Hybrid Electric Vehicle, Bilwa A. Jadhav

Open Access Theses

With research showing an alarming rate of increase in global warming and thus causing dangerous instabilities in the weather, a strong push has been initiated to reduce greenhouse gas emissions. Transportation being one of the top offenders in greenhouse gas emissions, has led the drive for improving the efficiency of the modern automobile. One of the current strategies for reducing the emissions produced by the transportation sector is hybrid vehicles powered from both a fuel such as gasoline, diesel, or hydrogen; and electricity. This merger has proven to be effective at decreasing harmful emissions including, carbon dioxide (CO 2 ) …