Mechanical Engineering Commons^™

Kinetic Model For Triglyceride Hydrolysis Using Lipase:Review, Heri Hermansyah, A. Wijanarko, Dianursanti Dianursanti, Misri Gozan, Praswasti P. D.K Wulan, Rita Arbianti, Roekmijati W. Soemantojo, Tania Surya Utami, Yuliusman Yuliusman, Momoji Kubo, Naomi Shibasaki Kitakawa, Toshiy Yonemoto

Makara Journal of Technology

Triglyceride hydrolysis using lipase has been proposed as a novel method to produce raw materials in food and cosmetic industries such as diacylglycerol, monoacylglycerol, glycerol and fatty acid. In order to design a reactor for utilizing this reaction on industrial scale, constructing a kinetic model is important. Since the substrates are oil and water, the hydrolysis takes place at oil-water interface. Furthermore, the triglyceride has three ester bonds, so that the hydrolysis stepwise proceeds. Thus, the reaction mechanism is very complicated. The difference between the interfacial and bulk concentrations of the enzyme, substrates and products, and the interfacial enzymatic reaction …

Sulfonation Of Cptfe Film Grafted Styrene For Proton Exchange Membrane Fuel Cell, Yohan Yohan

Makara Journal of Technology

Sulfonation of cPTFE Film grafted Styrene for Proton Exchange Membrane Fuel Cell. Sulfonation of γ-ray iradiated and styrene-grafted crosslinked polytetrafluoroethylene film (cPTFE-g-S film) have been done. The aim of the research is to make hydropyl membrane as proton exchange membrane fuel cell. Sulfonation was prepared with chlorosulfonic acid in chloroethane under various conditions. The impact of the percent of grafting, the concentration of chlorosulfonic acid, the reaction time,and the reaction temperature on the properties of sulfonated film is examinated. The results show that sulfonation of surface-grafted films is incomplete at room temperature. The increasing of concentration of chlorosulfonic acid and …

A Fuzzy Logic Controller For Autonomous Wheeled Vehicles, Mohamed Trabia, Linda Z. Shi, Neil Eugene Hodge

Mechanical Engineering Faculty Research

Autonomous vehicles have potential applications in many fields, such as replacing humans in hazardous environments, conducting military missions, and performing routine tasks for industry. Driving ground vehicles is an area where human performance has proven to be reliable. Drivers typically respond quickly to sudden changes in their environment. While other control techniques may be used to control a vehicle, fuzzy logic has certain advantages in this area; one of them is its ability to incorporate human knowledge and experience, via language, into relationships among the given quantities. Fuzzy logic controllers for autonomous vehicles have been successfully applied to address various …

Biogasoline Production From Palm Oil Via Catalytic Hydrocracking Over Gamma-Alumina Catalyst, Anondho Wijanarko, Dadi Ahmad Mawardi, Mohammad Nasikin

Makara Journal of Technology

Biogasoline Production from Palm Oil Via Catalytic Hydrocracking over Gamma-Alumina Catalyst. Bio gasoline conversion from palm oil is an alternative energy resources method which can be substituted fossil fuel base energy utilization. Previous research resulted that palm oil can be converted into hydrocarbon by catalytic cracking reaction with γ-alumina catalyst. In this research, catalytic cracking reaction of palm oil by γ-alumina catalyst is done in a stirrer batch reactor with the oil/catalyst weight ratio variation of 100:1, 75:1, and 50:1; at suhue variation of 260 to 340oC and reaction time variation of 1 to 2 hour. Post cracking reaction, bio …

Segmental Sinusoidal Model For Speech Signal Coding, Florentinus Budi Setiawan, Soegijardjo Soegijoko, Sugihartono Sugihartono, Suhartono Tjondronegoro

Makara Journal of Technology

Segmental Sinusoidal Model for Speech Signal Coding. Periodic signal can be decomposed by sinusoidal component with Fourier series. With this characteristic, it can be modeled referring by sinusoidal form. By the sinusoidal model, signal can be quantized in order to encode the speech signal at the lower rate. The recent sinusoidal method is implemented in speech coding. By using this method, a block of the speech signal with 20 ms to 30 ms width is coded based on Fourier series coefficients. The new method proposed is quantization and reconstruction of speech signal by the segmental sinusoidal model. A segment is …

A Study On Parallel Computation Tools On Networked Pcs, Heru Suhartanto

Makara Journal of Technology

A Study on Parallel Computation Tools on Networked PCs. Many models for natural phenomena, engineering applications and industries need powerfull computing resources to solve their problems. High Performance Computing resources were introduced by many researchers. This comes in the form of Supercomputers and with operating systems and tools for development such as parallel compiler and its library. However, these resources are expensive for the investation and maintenance, hence people need some alternatives. Many people then introduced parallel distributed computing by using available computing resource such as PCs. Each of these PCs is treated as a processors, hence the cluster of …

Crude Oil Sludge Degradation In Microcosmic Scale: Simple Simulation As Preliminary Study On Land Treatment Bioremediation., Astri Nugroho

Makara Journal of Technology

Crude Oil Sludge Degradation in Microcosmic Scale: Simple Simulation as Preliminary Study on Land Treatment Bioremediation. A study in microcosmic condition has been carried out to evaluate the bacterial hydrocarbonoclastic capability in increasing the oil sludge degradation being mixed with NPK fertilizer as nitrogen resources. Aerobic test was carried out by putting erlenmeyers in a shaker incubator, 120 rpm shaking speed, at 50°C temperature. While 150 days in microcosmic one observation showed that the consortium has the potential to grow up to 50% (v/v) sludge oil load. Maximum growth and maximum growth rate of the consortium occurred in the III …

Determination Of Operation Condition And Product Dimension Accuracy Optimization Of Filament Deposition Modelling On Layer Manufacturing Application, Slamet A. Widyanto, Alva Edy Tontowi, Jamasri Jamasri, Heru Santoso Budi Rochardjo

Makara Journal of Technology

Layer manufacturing process has proven as a process that can produce a high complexity mechanical part. Now, Improvement of LM methods continuously conduct that is aimed to increase precessions and efficiency of these processes. Pressure filament deposition modelling is a form of layer manufacturing process that is designed to produce a plastic part with controlling its semisolid phase. In this research, the equipment of filament depositor is designed and tested to make the product filament deposition. With operation condition observation, the optimal temperature and pressure of deposition process was determined. These experiments used PVC as crystalline material and polypropylene as …

Magnetic Field Effects On Caco3 Precipitation Process In Hard Water, Nelson Saksono, Setijo Bismo, Elsa Krisanti, Azwar Manaf, Roekmijati Widaningrum

Makara Journal of Technology

Magnetic Field Effects on CaCO3 Precipitation Process in Hard Water. Magnetic treatment is applied as physical water treatment for scale prevention especially CaCO3, from hard water in piping equipment by reducing its hardness. Na2CO3 and CaCl2 solution sample was used in to investigate the magnetic fields influence on the formation of particle of CaCO3. By changing the strength of magnetic fields, exposure time and concentration of samples solution, this study presents quantitative results of total scale deposit, total precipitated CaCO3 and morphology of the deposit. This research was run by comparing magnetically and non-magnetically treated samples. The results showed an …

Stress Corrosion Cracking Behavior Of Stainless Steel 304 In The Sulfuric Acid Environment Due To Prestrain, Mohammad Badaruddin, Ahmad Suudi, Arinal Hamni

Makara Journal of Technology

Stress Corrosion Cracking Behavior of Stainless Steel 304 in the Sulfuric Acid Environment Due to Prestrain. The aim of research is to investigate the effect of prestrain on the stress corossion cracking behavior of AISI 304 stainless steel in the sulfuric acid of 10% concentration under the static cantilever loading according to ASTM E-1681 standart. The specimen of 304 Stainless steel was strain up over the yield strength until reaching the uniform strain of 5% and 10% using servopulser UTM 9506 under the displacement control of 0,3 mm/sec. The results of test show that the prestrain of 5% specimen is …

Order And Disorder, Entropy In Math, Science, Nature And The Arts, Sol Neeman Ph.D., Arie Maharshak

Engineering Studies Faculty Publications and Creative Works

Often, science and engineering students have difficult time in viewing certain concepts in their holistic form. An example for such a concept is the concept of Entropy. Although it originated from the field of thermodynamics, the relation between order and disorder is a profound one and manifests itself in various fields, sometimes unrelated, such as math and science, nature and the arts. In the discipline of physics, the amount of disorder in a system has been quantified by the concept of Entropy. In the area of information theory it provides a quantitative measure of the amount of compression that may …

2nd Annual Undergraduate Research Conference Abstract Book, University Of Missouri--Rolla

Undergraduate Research Conference at Missouri S&T

No abstract provided.

Effect Of Firing Temperature And Holding Time On Characterization Of Al/Sic Metal Matrix Composites Produced By Pressureless Infiltration., Anne Zulfia, Myrna Ariati

Makara Journal of Technology

Effect of Firing Temperature and Holding Time on Characterization of Al/SiC Metal Matrix Composites Produced by Pressureless Infiltration. The production of Al-SiC metal matrix composite can be carried out by pressureless metal infiltration processs (PRIMEX). The experiment was conducted using aluminium AC2B ingot as a matrix and 50%Vf SiC powder as a reinforcement which is mixed with 10% Mg powder for wetting agent. The variables of this experiment are holding time and firing temperature to investigate the effect of these conditions on mechanical properties of Al-SiC metal matrix composites. Holding time was conducted for 2,5,8,10,12 hours and firing temperatures was …

Modification Of Bonding Strength Test Of Wc Hvof Thermal Spray Coating On Rocket Nozzle, Bondan T. Sofyan, Haposan J. Pardede, Marizki Stefano, Edi Sofyan

Makara Journal of Technology

Modification of Bonding Strength Test of WC HVOF Thermal Spray Coating on Rocket Nozzle. One way to reduce structural weight of RX-100 rocket is by modifying the nozzle material and processing. Nozzle is the main target in weight reduction due to the fact that it contributes 30 % to the total weight of the structur. An alternative for this is by substitution of massive graphite, which is currently used as thermal protector in the nozzle, with thin layer of HVOF (High Velocity Oxy-Fuel) thermal spray layer. This paper presents the characterization of nozzle base material as well as the modification …

Development Of Fiber-Optic Humidity Sensor Probe With Gelatin Cladding, Akhiruddin Maddu, Kun Modjahidin, Sar Sardy, Hamdani Zain

Makara Journal of Technology

Development of Fiber-Optic Humidity Sensor Probe with Gelatin Cladding. Humidity sensor based on optical fiber with gelatin cladding has been developed. In this humidity sensor probe, the origin cladding of optical fiber is replaced by gelatin coating as humidity sensitive cladding. Testing of the optical fiber sensor probe was conducted by measuring of light intensity transmitted on the optical fiber probe for each variation of different humidity treatments. Response of the optical fiber sensor probe measured from 42%RH to 99%RH, the results show an optical transmission curve varied with relative humidity (RH). Optical transmission in the optical fiber probe increase …

On The Performance Of Imt-2000 Communication Link Based On Stratospheric Platforms, Iskandar Iskandar, Shigeru Shimamoto

Makara Journal of Technology

A new means for providing wireless communication has been currently proposed. It is based on aerial vehicle known as High Altitude Platform or Stratospheric Platforms (SPF). The SPF will be operated at an altitude of 17-22 km above the ground. Therefore, the channel condition may be different compared with those of the conventional terrestrial or satellite wireless channel. In this paper, the channel propagation characteristic of such a system is firstly investigated by means of ray tracing algorithm. We emphasize our investigation in a typical urban environment, in which the mobile users mostly exist. We developed building block model for …

Analysis Of Technical Energy Losses By Using Simulation, Betrianis Betrianis, Randite Herawan

Makara Journal of Technology

Model is a representation of a system. Through model, it can be easier to forecast and control the changing of each element system. Electricity distribution is also a system. Losses are general problem that exist in a distribution network system. But with the right methods, specifically technical energy losses can be reduced in order to increase the efficiency. By making model of the distribution network, the value of technical energy losses in the whole network as well as in every line can be observed. Simulation can also be used to see all losses reduction alternatives. By comparing results from each …

Modeling Of Coupled-Tank System Using Fuzzy Takagi-Sugeno Model, Aries Subiantoro

Makara Journal of Technology

Modeling of Coupled-Tank System Using Fuzzy Takagi-Sugeno Model. This paper describes modeling of coupledtank system based on data measurement using fuzzy Takagi-Sugeno model. The fuzzy clustering method of Gustafson- Kessel algorithm is used to classify input-output data into several clusters based on distance similarity of a member of input-output data from center of cluster. The formed clusters are projected orthonormally into each linguistic variables of premise part to determine membership function of fuzzy Takagi-Sugeno model. By estimating data in each cluster, the consequent parameters of fuzzy Takagi-Sugeno model are calculated using weighted least-squares method. The resulted fuzzy Takagi-Sugeno model is …

Design Of Induction Motor Drive Without Velocity Sensor Using Current Vector Controller With Full And Reduced Observer Moving To Dq Axis, Ridwan Gunawan, Feri Yusivar, Wahidin Wahab, Zuhal A. Kadir

Makara Journal of Technology

Design of Induction Motor Drive Without Velocity Sensor Using Current Vector Controller with Full and Reduced Observer Moving to DQ Axis. The observer is used in estimation velocity sensor usually in α-β axis, therefore this situation will need an extra transformation when we want to add compensator because the flux model is in direct and quadrature-axis dq. Every used the transformation to make possible emerge an error. So in this simulation is used a method to estimate the velocity of induction motor drive with observer that is moved to dq-axis. The model of actual motor used is in alfa-beta axis, …

Hybrid Identification System With Arx And Fast Fourier Transform In Application Of A Quarter Of Vehicle Half Active Suspension, Noveri Lysbetti M, Antonius R.

Makara Journal of Technology

Hybrid Identification System with ARX and Fast Fourier Transform in Application of a Quarter of Vehicle Half Active Suspension. In a control system problem, identification system mechanism is a absolute thing, especially in adaptation controlling to disturbance changing. For that case, is needed an identification method which can identify the changing of disturbance in that system. The aim of this research is to give an alternative in system/plant identification which is a combination (hybrid) of ARX and Fast Fourier Transform. So, it is needed an algorithm design for identification process. In this case, the designed algorithm will be implemented in …

Power-Scavenging Mems Robots, Daniel J. Denninghoff

Theses and Dissertations

This thesis includes the design, modeling, and testing of novel, power-scavenging, biologically inspired MEMS microrobots. Over one hundred 500-μm and 990-μm microrobots with two, four, and eight wings were designed, fabricated, characterized. These microrobots constitute the smallest documented attempt at powered flight. Each microrobot wing is comprised of downward-deflecting, laser-powered thermal actuators made of gold and polysilicon; the microrobots were fabricated in PolyMUMPs® (Polysilicon Multi-User MEMS Processes). Characterization results of the microrobots illustrate how wing-tip deflection can be maximized by optimizing the gold-topolysilicon ratio as well as the dimensions of the actuator-wings. From these results, an optimum actuator-wing configuration was …

Synthesis Of Fuel Cell Membrane: Copolymerization Of Styrene On Etfe Film By Grafted Pre-Irradiation, Yohan Yohan, Rifai M. Nur, Lilik Hendrajaya, E. S. Siradj

Makara Journal of Technology

Synthesis of Fuel Cell Membrane: Copolymerization of Styrene on ETFE Film by Grafted pre-Irradiation. Preirradiation Grafting styrene monomer on ETFE film has been prepared. Research has been performed by γ-ray radiation at various total dose from 2.5 – 12.5 kGy and various dose rate from 1.3 – 1.9 kGy/hour. Irradiated copolymer is then grafted by styrene monomer in various solvent: ethanol, 2-propanol, and toluene, various concentration from 20 – 70% volume, various temperature from 50 – 90oC, and various grafting time from 2 – 12 hours. The results showed that percent of grafting is increase with increase of total dose …

Design Of Product Placement Layout In Retail Shop Using Market Basket Analysis, Isti Surjandari, Annury Citra Seruni

Makara Journal of Technology

Retailing is an industry with high level of competition. It is a customer-based industry which depends on how it could be aware of what the customers’ needs and requirements are. One technique most used in supermarkets is the mix merchandise. The purpose of this paper is to identify associated products, which then grouped in mix merchandise with the use of market basket analysis. This association between products then will be applied in the design layout of the product in the supermarket. The process of identifying the related products bought together in one transaction is done by using data mining technique. …

Production Hydrogen And Nanocarbon Via Methane Decomposition Using Ni-Based Catalysts. Effect Of Acidity And Catalyst Diameter, Widodo W. Purwanto, M. Nasikin, E. Saputra, L. Song

Makara Journal of Technology

Objectives of this research are mainly to study impacts of acidity strength (by varying amount of precipitant and loading Al-Si) and the effect of nickel particle size (by varying calcinations temperature) on decomposition reaction performances. In this research, high-nickel-loaded catalyst is prepared with two methods. Ni-Cu/Al catalysts were prepared with co-precipitation method. While the Ni-Cu/Al-Si catalyst were prepared by combined co-precipitation and sol-gel method. The direct cracking of methane was performed in 8mm quartz fixed bed reactor at atmospheric pressure and 500-700°C. The main results showed that the Al content of catalyst increases with the increasing amount of precipitant. The …

Design And Implementation Of 1-2 Ghz Stepped Frequency Gpr For Buried Metal Detection, Joko Suryana, Andriyan B. Suksmono, Tati R. Mengko

Makara Journal of Technology

Design and Implementation of 1-2 GHz Stepped Frequency GPR for Buried Metal Detection. In this paper, we describe the design and realization steps of 1 – 2 GHz SFGPR (Stepped Frequency Ground Penetrating Radar) transceiver for metal detection under the ground. Before using prototyped GPR for detecting the metal under the ground, several of calibration processes must be performed, namely phase calibration and monocycle pulse waveform calibration. After completing the calibrations, this prototyped GPR would be ready for detecting a hidden object such as a metal plate 5 cm under the ground in our small test range size 25 cm …

Simultaneous Treatment Of Organic (Phenol) And Heavy Metal (Cr6+ Or Pt4+) Wastes Over Tio2, Zno-Tio2 And Cds-Tio2 Photocatalysts, Slamet Slamet, R. Arbianti, Daryanto Daryanto

Makara Journal of Technology

Simultaneous Treatment of Organic (Phenol) and Heavy Metal (Cr6+ or Pt4+) Wastes over TiO2, ZnO-TiO2 and CdS-TiO2 Photocatalysts. Treatment of heavy metal (Cr6+ and Pt4+) and organic (phenol) wastes has been studied using the relatively new method, i.e. simultaneous photocatalytic process over TiO2 photocatalysts in the batch photoreactor. Following the photocatalytic reduction of the heavy metal wastes, recovery of Cr and Pt was carried out by precipitation and leaching method, respectively. The experimental results show that in the simultaneous photocatalytic system, there is a synergism effect between the photocatalytic reduction of heavy metal waste (Cr6+ or Pt4+) and the oxidation …

Design Of Generating Dual Frequency Operation For Triangular Microstrip Antenna Using Electromagnetic Coupling, Indra Surjati, Eko Tjipto Rahardjo, Djoko Hartanto

Makara Journal of Technology

Design of Generating Dual Frequency Operation for Triangular Microstrip Antenna Using Electromagnetic Coupling. A new design is proposed in this paper by applying a pair of slits using a microstrip feed line. Therefore the microstrip line feeding system is electromagnetically coupled to the patch. The antenna works at two different frequencies in the range from 2 GHz to 4 GHz (S band frequency). The results of the simulation shows that the dual frequency operation can be created when the slit width is 1 mm and the height of the slits ranges from 10 mm to 14 mm with inter slit …

Development Of Low Frequency Vibration Method Of Direct-Write Deposition Relevant To Layer Manufacturing Application, Susilo Adi Widyanto, Alva Edy Tontowi, Jamasri Jamasri, Heru Santosa Budi Rochardjo

Makara Journal of Technology

The research of deposition process is the first step in development process of multi materials selective laser sintering. The deposition process enables to settle multi materials powder in horizontal formation on one layer. In this research we use low frequency (70 - 200Hz) to vibrate a hopper nozzle in which powder is settled. The research method consists of two steps, the first step is to determine flow-ability parameters and the second is to join flow ability parameter with other parameters such that the line width can be controlled. The results show that the line width depends on uniformity of particle …

Support For A Delivery Train Based Material Handling Mechanism, Sai P. Boyedapu

Electrical & Computer Engineering Theses & Dissertations

Modeling a delivery train system is more challenging than traditional forklift systems as the delivery train model consists of a tugger, cart and a controller that combine to deliver materials within a manufacturing plant. Also, the decision logic for selection of carts and tuggers, joining of loads to particular delivery trains is more complicated than forklift systems. Simulation software such as Arena, Automod and Flexsim do not provide direct support for modeling delivery train systems.

In this thesis, an object-oriented, platform and language independent model of a delivery train was designed. The model was then implemented as an extension to …

2005 (Fall) Ensi Informer Magazine, Morehead State University. Engineering Sciences Department

ENSI Informer Magazine Archive

The ENSI Informer Magazine published in the fall of 2005.