Mechanical Engineering Commons^™

Stochastic Optimization Of Supply Chain Risk Measures –A Methodology For Improving Supply Security Of Subsidized Fuel Oil In Indonesia, Adinda Yuanita, Andi Noorsaman Sommeng, Anondho Wijonarko

Makara Journal of Technology

Monte Carlo simulation-based methods for stochastic optimization of risk measures is required to solve complex problems in supply security of subsidized fuel oil in Indonesia. In order to overcome constraints in distribution of subsidized fuel in Indonesia, which has the fourth largest population in the world—more than 250,000,000 people with 66.5% of productive population, and has more than 17,000 islands with its population centered around the nation's capital only—it is necessary to have a measurable and integrated risk analysis with monitoring system for the purpose of supply security of subsidized fuel. In consideration of this complex issue, uncertainty and probability …

Thermodynamic Analysis Of Irreversible Heat-Transformers, Niccolo` Giannetti, Arnas Arnas, Andrea Rocchetti, Kiyoshi Saito

Makara Journal of Technology

Absorption heat transformers extend the possibilities for efficient and environment-friendly energy conversion processes. Based on a general thermodynamic model of three-thermal cycles with finite thermal capacity of the heat sources, this paper is intent upon analyzing and optimizing the performance of absorption heat transformers, by including the influence of irreversibility in the analytical expression of the system efficiency. Dimensionless parameters for an overall optimization are defined and a first screening is performed to clarify their influence. Dependence on the main factors is highlighted to suggest how to change them in order to enhance the whole system performance. Under this point …

Power Maximization Of A Three-Phase Hydrokinetic Turbine, Matthew Carleson

Senior Theses

As Earth`s expendable resources dwindle, the need for alternative, renewable energy sources grows. Out of this need, an old favorite source is rising in popularity: small water turbines. Water-driven turbines first began as a means for turning mills and eventually evolved into massive dams that can power whole regions. This project focused on the construction of, and testing the properties of, a small pico-hydro power turbine. By using compressed air to drive the turbine, a representation of the peak power output was measured, serving as a basis for determining the value of pico-power systems in regards to the world`s current …

College Of Engineering Senior Design Competition Spring 2015, University Of Nevada, Las Vegas

Fred and Harriet Cox Senior Design Competition Projects

Part of every UNLV engineering student’s academic experience, the senior design project stimulates engineering innovation and entrepreneurship. Each student in their senior year chooses, plans, designs, and prototypes a product in this required element of the curriculum. A capstone to the student’s educational career, the senior design project encourages the student to use everything learned in the engineering program to create a practical, real world solution to an engineering challenge. The senior design competition helps focus the senior students in increasing the quality and potential for commercial application for their design projects. Judges from local industry evaluate the projects on …

Three Dimensional Simulations Of Tornado Sheltering Effect Of Man-Made Structures, Piotr Gorecki

Graduate Theses and Dissertations

A three dimensional computational fluid dynamics (CFD) model was utilized to investigate tornado-like vortex interactions with wide man-made structures. The tornado-like wind profile was approximated using Rankine vortex model. By utilizing the CFD model, it was explained why tornadoes exhibit less damage on leeward side of large structures. During the preliminary stage of this study, a perpendicular vortex-prism interaction was analyzed. The prism height and the length were equal to the vortex core radius. The prism was also 12 times wider than the vortex core radius. During the vortex-prism interaction, the near-ground portion of the vortex was blocked by the …

Conceptual Development Of An Impact-Attenuation System For Intersecting Roadways, Joseph G. Putjenter

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Longitudinal barriers are commonly used to shield hazards, including stiff bridge rail ends and slopes. In some locations, a secondary roadway intersects the primary roadway within the guardrail’s length-of-need (LON). Some intersections have as little as 15 ft (4.6 m) between the intersection and beginning of the bridge railing, which require short-radius guardrail systems. No short-radius systems have been tested and approved to current impact safety standards for shielding hazards with these conditions.

Site conditions provided by the Nebraska Department of Roads were used to determine the constraints for a new safety treatment for intersecting roadways and include intersection radii, …

Creep And Shrinkage Behavior Of Fly Ash Based Geopolymer Concrete, Md Rashedul Islam

Doctoral Dissertations

The manuscript presented herein is based on the investigation of the short and long term properties of fly ash based geopolymer concrete (GPC) and their link to fly ash characteristics. Fly ash (FA) exhibits a significantly different particle morphology, which impacts the mechanical properties of the resulting GPC and typically contains impurities that fluctuate from one FA source to another. A key contribution of this research work is the capturing of the variability posed by the FA stockpile with a wide range of physical, chemical, and crystallographic characteristics as a source material to select the GPC mix design. In the …

Group Decisions In Value Management, Christiono Utomo, Farida Murti, Arazi Idrus

Makara Journal of Technology

This research deals with a technique to expedite group decision making during the selection of technical solutions for value management process. Selection of a solution from a set of alternatives is facilitated by evaluating using multicriteria decision making techniques. During the process, every possible solution is rated on criteria of function and cost. Function deals more with quality than with quantity, and cost can be calculated based on the theoretical time value of money. Decision-making techniques based on satisfying games are applied to determine the relative function and cost of solutions and hence their relative value. The functions were determined …

Numerical Characterization Of Convective Heat Transfer Of Low-Rise Buildings, Ranchi Chen

Open Access Theses

The convective heat transfer coefficient (CHTC) is an important parameter to evaluate the efficiency of building-integrated photovoltaic/Thermal (PV/T) system and the energy exchange within the turbulent atmospheric boundary layer. Reynolds-average Navier-Stokes approach has been frequently used to predict the CHTC at the surface of low rise roof but incapable of predicting transient behavior of separation, reattachment and recirculation both on the windward and leeward surface. However, Large Eddy Simulation approach (LES) could provide accurate flow field and temperature field around the low rise building. ^ The current study uses Large Eddy Simulation with Smagorinsky-Lily model and the Shear Stress Transport …

Modeling Person-To-Person Contaminant Transport In Enclosed Environments, Chun Chen

Open Access Dissertations

It is essential to predict person-to-person contaminant transport in enclosed environments to improve air distribution design and reduce the infection risk from airborne infectious diseases. This study aims to improve and accelerate the simulation of person-to-person contaminant transport in enclosed environments. ^ This investigation first conducted experimental measurements of person-to-person contaminant transport in an office mockup and the first-class cabin of a functional MD-82 aircraft. The experimental data of steady-state airflow, temperature, and gas contaminant concentration fields obtained in the office were used to validate the steady-state computational fluid dynamics (CFD) models. In the aircraft cabin, the transient particle concentrations …

Seebeck Coefficient Of Soi Layer Induced By Phonon Transport, Faiz Salleh, Takuro Oda, Yuhei Suzuki, Yoshinari Kamakura, Hiroya Ikeda

Makara Journal of Technology

The Seebeck coefficient of a patterned Si wire on P-doped SOI (Si-on-insulator) layer with a carrier concentration of 1018 cm-3 was measured near room temperature. The Seebeck coefficient is found to be smaller than that in the SOI layer and to be closer to the calculated Seebeck coefficient including the electronic contribution. The decrease in the Seebeck coefficient of Si wire is likely to occur due to the elimination of the contribution of phonon drag part. From the theoretical calculation of scattering rates by considering the scattering processes in phonon system, it is considered that an increase in phonon-boundary scattering …

Construction Of A Novel Method Of Measuring Thermal Conductivity For Nanostructures, Hiroya Ikeda, Shoma Yoshida, Yuhei Suzuki, Veerappan Manimuthu, Faiz Salleh, Fujio Kuwahara, Masaru Shimomura, Kenji Murakami

Makara Journal of Technology

With the aim of characterizing the thermal conduction in a nanometer-scaled materials, we have constructed a novel method on the basis of an ac calorimetric method. In this method, periodic sample heating is performed by light irradiation and the corresponding periodic temperature is detected by infrared irradiative thermometer. This makes us measure the thermal diffusivity out of contact with the objective sample. In the present study, we confirm to measure the thermal diffusivity of bulk Si and Cu by this non-contact method with halogen-lamp irradiation. In determining the thermal diffusivity from the relationship between distance deviation and delay time, the …

Phonon-Drag Contribution To Seebeck Coefficient Of Ge-On-Insulator Substrate Fabricated By Wafer Bonding Process, Veerappan Manimuthu, Shoma Yoshida, Yuhei Suzuki, Faiz Salleh, Mukannan Arivanandhan, Yoshinari Kamakura, Yasuhiro Hayakawa, Hiroya Ikeda

Makara Journal of Technology

In order to build high-sensitivity infrared photodetectors using SiGe nanowires, we investigate the thermoelectric characteristics of Ge-on-insulator (GOI) layers as a reference for SiGe. We fabricate p-type GOI substrates with an impurity concentration of 1016-1018cm-3 by a wafer-bonding process using Ge and oxidized Si wafers. Annealing treatment is performed in order to further increase the bonding strength of Ge/SiO2 interface. We measure the Seebeck coefficient in the temperature range of 290-350 K. The Seebeck coefficient of the GOI layers is very close to the theoretical value for Ge, calculated on the basis of carrier transport. Hence, there is a small …

Fiber Optic Ring Resonator Sensor Detection Technique Based On Spectral Intensity Integration, Purnomo Sidi Priambodo, Sasono Rahardjo, Gunawan Witjaksono, Djoko Hartanto

Makara Journal of Technology

Resonant field phenomenon in optical ring resonator has been a major theme for various studies and can be used for various sensor applications. The spectral response shape changes are subjects to be discussed and analyzed for detection in optical sensor system. The spectral response changes are caused by various factors ranging from refractive index of the surrounding medium, medium loss due to absorption and scattering, and coupling variation between waveguides. These optical phenomena are mostly used for bio-sensor applications, since it is free from electromagnetic interference (EMI) and non-physically destructive. In this paper, we discuss our current research in developing …

The Effects Of The Types Of Milk (Cow, Goat, Soya) And Enzymes (Rennet, Papain, Bromelain) Toward Cheddar Cheese Production, Ariestya Arlene, Anastasia Prima Kristijarti, Ivana Ardelia

Makara Journal of Technology

The objectives of this research are to study the effects of different types of milk and enzymes toward the yield and quality (moisture, ash, protein, fat content, and texture) of cheddar cheese and the interaction between those two variables during the process. The types of milk are cow, goat, and soya milk, while the types of enzymes are rennet, papain, and bromelain enzymes. Regarding the procedure, the milk is first pasteurized before CaCl2 and Lactobacillus lactis that acts as the acidifier starter as much as 0.2% (w/v) and 0.5% of the milk volume are added respectively. The amount of enzyme …

Hazard-Driven Drivers’ Behaviours Towards Vehicle-To-Median Safe Distances, Martha Leni Siregar

Makara Journal of Technology

A median is required for a two-way road to separate traffic from opposing lanes and to prevent head-on collisions. However, studies indicate that medians are also perceived as hazards which need to be avoided during driving. This hazard perception is manifested in drivers’ changing behavior towards various types of medians along the driving lanes inform of their tendency to allow various safe distances to the medians. The Indonesian Highway Capacity Manual (IHCM) does not differentiate between types of medians and the influence on the drivers’ choice of safe margin to the medians. Therefore, this study looks into how the existence …

Energy And Exergy Analysis Of Kalina Cycle For The Utilization Of Waste Heat In Brine Water For Indonesian Geothermal Field, Nasruddin Nasruddin, Agus Noor Sidiq, Abdulmajeed Mohamad, Rama Usvika

Makara Journal of Technology

The utilization of waste heat in a power plant system—which would otherwise be released back to the environment—in order to produce additional power increases the efficiency of the system itself. The purpose of this study is to present an energy and exergy analysis of Kalina Cycle System (KCS) 11, which is proposed to be utilized to generate additional electric power from the waste heat contained in geothermal brine water available in the Lahendong Geothermal power plant site in North Sulawesi, Indonesia. A modeling application on energy and exergy system is used to study the design of thermal system which uses …

Structural Integrity Of Conventional And Modified Railroad Bearing Adapters For Onboard Monitoring, Joseph Montalvo, Alexis Trevino, Arturo A. Fuentes, Constantine Tarawneh

Mechanical Engineering Faculty Publications

This paper presents a detailed study of the structural integrity of conventional and modified railroad bearing adapters for onboard monitoring applications. Freight railcars rely heavily on weigh bridges and stations to determine cargo load. As a consequence, most load measurements are limited to certain physical railroad locations. This limitation provided an opportunity for an optimized sensor that could potentially deliver significant insight on bearing condition monitoring as well as load information. Bearing adapter modifications (e.g. cut outs) were necessary to house the sensor and, thus, it is imperative to determine the reliability of the modified railroad bearing adapter, which will …

Understanding Residential Location Choices For Climate Change And Transportation Decision Making: Phase 2 Report, Kelly J. Clifton, Steven R. Gehrke, Kristina Marie Currans

Civil and Environmental Engineering Faculty Publications and Presentations

This research builds on the related Phase 1 project. In this second phase, we continue to study neighborhood and housing preferences that shape the residential location decision process. An online experimental survey tool is developed to investigate lifestyle preferences and tradeoffs that households make in their location decisions. This computer-aided experimental survey draws upon stated preference methods to engage participants in questions about residential location and transportation options. The survey infrastructure was extensively piloted (6-10% response rate). The 10-minute survey can be deployed for future investigations. This infrastructure is a contribution for the integration of visualized neighborhood typologies, or concepts, …

Analytical Modeling Of A Novel High-Q Disk Resonator For Liquid-Phase Applications, Mohomad S. Sotoudegan, Stephen M. Heinrich, Fabien Josse, Nicholas J. Nigro, Isabelle Dufour, Oliver Brand

Civil and Environmental Engineering Faculty Research and Publications

To overcome the detrimental effects of liquid environments on microelectromechanical systems resonator performance, the in-fluid vibration of a novel disk resonator supported by two electrothermally driven legs is investigated through analytical modeling and the effects of the system’s geometric/material parameters on the dynamic response are explored. The all-shear interaction device (ASID) is based on engaging the surrounding fluid primarily through shearing action. The theory comprises a continuous-system, multimodal model, and a single-degree-of-freedom model, the latter yielding simple formulas for the fundamental-mode resonant characteristics that often furnish excellent estimates to the results based on the more general model. Comparisons between theoretical …

A Field Investigation Of Composite Mud Brick Compressive Strength, Kevin D. Hale

Dissertations, Master's Theses and Master's Reports - Open

It has been highlighted in numerous publications that in the field of earth construction there is a strong disconnect between experimental work in the laboratory and its application in the field. The current study attempts to help bridge this gap with a field test conducted in Nampula, Mozambique. Mud bricks were made with a simple hand mold and reinforced with bamboo and straw fibers. Fibers were cut into lengths of 3 cm and 6 cm while being mixed in fractions of 0.125%, 0.25% and 0.50% by weight and compressive strength was measured using an application of the 3-point bending test. …

Stethoscope-Based Detection Of Detorqued Bolts Using Impact-Induced Acoustic Emissions, Joe Guarino, Robert Hamilton

Mechanical and Biomedical Engineering Faculty Publications and Presentations

Results of a preliminary study investigating a simple method for detecting looseness in bolted fasteners of a steel structure are presented. Extensive research by many investigators demonstrates that the frequency response of a bolted structural member changes when one or more bolts are loosened. A simple and effective method for detecting looseness can be applied to bolted joints, using inexpensive and commonly-available equipment and software. The difference between spectrograms associated with tight and loose bolts is clearly apparent due to the presence of a tell-tale mode when one or more bolts are loosened. Further, a striking difference can be elucidated …

Vibration Of Steel-Framed Floors Supporting Sensitive Equipment In Hospitals, Research Facilities, And Manufacturing Facilities, Di Liu

Theses and Dissertations--Civil Engineering

Floors have traditionally been designed only for strength and deflection serviceability. As technological advances have been made in medical, scientific and micro-electronics manufacturing, many types of equipment have become sensitive to vibration of the supporting floor. Thus, vibration serviceability has become a routinely evaluated limit state for floors supporting sensitive equipment. Equipment vibration tolerance limits are sometimes expressed as waveform peak acceleration, and are more often expressed as narrowband spectral acceleration, or one-third octave spectral velocity.

Current floor vibration prediction methods, such as those found in the American Institute of Steel Construction Design Guide 11, Floor Vibrations Due to Human …

Shape Memory Behavior Of Single Crystal And Polycrystalline Ni-Rich Nitihf High Temperature Shape Memory Alloys, Sayed M. Saghaian

Theses and Dissertations--Mechanical and Aerospace Engineering

NiTiHf shape memory alloys have been receiving considerable attention for high temperature and high strength applications since they could have transformation temperatures above 100 °C, shape memory effect under high stress (above 500 MPa) and superelasticity at high temperatures. Moreover, their shape memory properties can be tailored by microstructural engineering. However, NiTiHf alloys have some drawbacks such as low ductility and high work hardening in stress induced martensite transformation region. In order to overcome these limitations, studies have been focused on microstructural engineering by aging, alloying and processing.

Shape memory properties and microstructure of four Ni-rich NiTiHf alloys (Ni50.3Ti29.7Hf20, Ni50.7Ti29.3Hf20, …

Simulating Energy Efficient Control Of Multiple-Compressor Compressed Air Systems, Sean Murphy, J. Kelly Kissock

Mechanical and Aerospace Engineering Faculty Publications

In many industrial facilities it is common for more than one air compressor to be operating simultaneously to meet the compressed air demand. The individual compressor set-points and how these compressors interact and respond to the facility demand have a significant impact on the compressed air system total power consumption and efficiency. In the past, compressors were staged by cascading the pressure band of each compressor in the system. Modern automatic sequencers now allow more intelligent and efficient staging of air compressors.

AirSim, a compressed air simulation tool, is now able to simulate multiple-compressor systems with pressure band and automatic …

Color Removal From Pulp Mill Effluent Using Coal Ash Produced From Georgia Power Coal Combustion Plants, Christopher B. Willett

College of Graduate Studies: Theses & Dissertations

Two environmental concerns currently face Georgia: coal fly ash (CFA) waste from coal power plants, and the effluent generated by pulp mills. Pulp mill effluent discolors surface waters into which it is discharged, and has been proven to negatively impact the dissolved oxygen and carbon necessary for aquatic life. The proposed solution is a cost-effective adsorption treatment using an inexpensive but abundantly available waste material: CFA. CFA possesses beneficial properties that allow it to effectively remove contaminants, and is available at significantly reduced cost. The primary research objective was to define treatment parameters that would result in the maximum removal …

Influence Of Spatial Variations Of Railroad Track Stiffness And Material Inclusions On Fatigue Life, Celestin Nkundineza

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Railroad transportation is very important for economic growth and effective maintenance is one critical factor for its economic sustainability. The high repetitive forces from a moving railcar induce cyclic stresses that lead to rail bending and potential deterioration due to fatigue crack initiation and propagation. Previous research for prediction of fatigue life has been done under the assumptions of a uniform track bed and a homogeneous rail. However the spatial variation of the track stiffness is expected to increase the maximum stresses in the rail and, therefore, accelerate the fatigue process. The research described in this dissertation is focused on …

Micro- And Macro-Scale Modeling Of Filter Aging: Effects Of Particle Poly-Dispersity And Fiber Cross-Sectional Shape, Ahmed M. Saleh

Theses and Dissertations

The goal of this study is to further advance the state of the art in developing self-sufficient methods to predict the performance of an aerosol filter. The simulation methods developed in this study are based on first principles and consequently, they do not rely on empirical correction factors. These simulation methods can be used to predict the instantaneous collection efficiency and pressure drop of a filter under dust-loading conditions. In the current study, 3-D micro- and macroscale CFD models are developed to simulate the service life of flat-sheet and pleated filters. These CFD micro- and macroscale models are also used …

The Simulation & Evaluation Of Surge Hazard Using A Response Surface Method In The New York Bight, Michael H. Bredesen

UNF Graduate Theses and Dissertations

Atmospheric features, such as tropical cyclones, act as a driving mechanism for many of the major hazards affecting coastal areas around the world. Accurate and efficient quantification of tropical cyclone surge hazard is essential to the development of resilient coastal communities, particularly given continued sea level trend concerns. Recent major tropical cyclones that have impacted the northeastern portion of the United States have resulted in devastating flooding in New York City, the most densely populated city in the US. As a part of national effort to re-evaluate coastal inundation hazards, the Federal Emergency Management Agency used the Joint Probability Method …

College Of Engineering Senior Design Competition Fall 2014, University Of Nevada, Las Vegas

Fred and Harriet Cox Senior Design Competition Projects

Part of every UNLV engineering student’s academic experience, the senior design project stimulates engineering innovation and entrepreneurship. Each student in their senior year chooses, plans, designs, and prototypes a product in this required element of the curriculum. A capstone to the student’s educational career, the senior design project encourages the student to use everything learned in the engineering program to create a practical, real world solution to an engineering challenge. The senior design competition helps focus the senior students in increasing the quality and potential for commercial application for their design projects. Judges from local industry evaluate the projects on …