Mechanical Engineering Commons^™

Forensic Investigation Of Failed Mast Arms Of Traffic Signal Supported Structures, Genda Chen, Michael G. Barker, D. Scott Mackenzie, Christopher W. Ramsay, Joe Alderson, Lokeswarappa R. Dharani, Jiaqing Yu

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In Missouri, 11 traffic signal mast arms fractured at the arm-post weld connection in 7 years. To reduce this fatigue failure, the Missouri Department of Transportation developed a fatigue-resistant weld profile that increases the weld leg and reduces the slope of the weld at the toe. This study investigated causes of the failed arms, compared performance of new and old weld profiles, and suggested retrofitting measures for further investigation. The scope included a metallurgical investigation of one failed field mast arm, laboratory fatigue testing of five prototype mast arms (two new and three old profiles), and laboratory failure analysis of …

Ole Miss Engineer 2001

Ole Miss Engineer

No abstract provided.

Ascent And Decompression Of Viscous Vesicular Magma In A Volcanic Conduit, Helene Massol, Claude Jaupart, Darrell Pepper

Mechanical Engineering Faculty Research

During eruption, lava domes and flows may become unstable and generate dangerous explosions. Fossil lava-filled eruption conduits and ancient lava flows are often characterized by complex internal variations of gas content. These observations indicate a need for accurate predictions of the distribution of gas content and bubble pressure in an eruption conduit. Bubbly magma behaves as a compressible viscous liquid involving three different pressures: those of the gas and magma phases, and that of the exterior. To solve for these three different pressures, one must account for expansion in all directions and hence for both horizontal and vertical velocity components. …

Application Of Dynamic System Identification To Timber Beams - Part I, S T. Peterson, D I. Mclean, M D. Symans, David Pollock, W F. Cofer, R N. Emerson, Kenneth J. Fridley

Faculty Publications - Biomedical, Mechanical, and Civil Engineering

In this first part of a two-part paper, development of a method of dynamic system identification for timber beams is presented with an analytical verification of the method using a finite-element model. A method of global nondestructive evaluation for identifying local damage and decay in timber beams is investigated in this paper. Experimental modal analysis is used in conjunction with a previously developed damage localization algorithm. The damage localization algorithm utilizes changes in modal strain energy between the mode shapes of a calibrated model, representing the undamaged state of the beam of interest, and the experimentally obtained mode shapes for …

Reliability Indices For Bolted And Nailed Connections In Wood Structures, David Pollock, Donald A. Bender

Faculty Publications - Biomedical, Mechanical, and Civil Engineering

Recently published test data for bolted and nailed connections was evaluated to assess the structural reliability inherent in current allowable stress design procedures for connections in wood structures. Reliability indices were determined for timber connections using standard firstorder, second moment (FOSM) procedures. For the connections considered in this study, reliability indices range from 2.6 to5.1, generally providing higher levels of safety than the structural members in timber structures.

Application Of Dynamic System Identification To Timber Beams - Part Ii, S T. Peterson, D I. Mclean, M D. Symans, David Pollock, W F. Cofer, R N. Emerson, Kenneth J. Fridley

Faculty Publications - Biomedical, Mechanical, and Civil Engineering

In a companion paper, a method of global nondestructive evaluation (NDE) for identifying local damage and decay in timber beams was developed and verified analytically using a finite-element model of a timber beam. The previously presented method of damage localization employs experimental modal analysis and an algorithm that monitors changes in modal strain energy between the mode shapes of a damaged beam with respect to the undamaged state of the beam. In this second part of a two-part paper, experimental laboratory tests on simply supported timber beams are presented to verify the capabilities and determine the limitations of the proposed …

Ole Miss Engineer 2001

Ole Miss Engineer

No abstract provided.

Fatigue Assessment Of Traffic Signal Mast Arms Based On Field Test Data Under Natural Wind Gusts, Genda Chen, Jingning Wu, Jiaqing Yu, Lokeswarappa R. Dharani, Michael G. Barker

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In recent years, several states including Missouri, Wyoming, California, and Texas experienced fracture failures of traffic signal mast arms. Almost all the failures are associated with the propagation of defects or cracks. It is therefore imperative to evaluate existing mast arms using a simple yet accurate procedure. A statistical methodology is proposed to predict the fatigue life of signal mast arm structures on the basis of field-measured strain data. The annual occurrence of various stress levels is determined using the historical wind speed data in the vicinity of a mast arm structure and the strain readings of the structure under …

Stress And Thermal Analysis Of The Lotec Carrier, Scott Thomas

Honors Capstone Projects and Theses

No abstract provided.

Ole Miss Engineer 2000

Ole Miss Engineer

No abstract provided.

Matrix Structural Analysis, 2nd Edition, William Mcguire, Richard H. Gallagher, Ronald D. Ziemian

Faculty Books

The aims of the first edition of Matrix Structural Analysis were to place proper emphasis on the methods of matrix structural analysis used in practice and to lay the groundwork for more advanced subject matter. This extensively revised Second Edition accounts for changes in practice that have taken place in the intervening twenty years. It incorporates advances in the science and art of analysis that are suitable for application now, and will be of increasing importance in the years ahead. It is written to meet the needs of both the present and the coming generation of structural engineers.

KEY FEATURES …

Evaluation Of Extreme Wind Speeds In Relation To The Design Of Coastal Structures In Tanzania, Alfonse Dubi

Tanzania Journal of Engineering and Technology (TJET)

Five distribution functions, FT-I and Weibull with the exponent k = 0.75, 1.0, 1.4 and 2.0 respectively, have been applied to 25-year wind data collected between 1972 and 1996 at Tanga, Dar Es Salaam, Zanzibar and Mtwara Meteorological stations. One maximum value for every year from the full data record was drawn to constitute the annual maxima series for each station. For each of the stations, 2-, 50- and 100-year return wind speeds with corresponding 90% confidence intervals were computed. The distribution functions were fitted to the data by the Least Squares Method. Results from the study show that FT-I …

Application Of Vibrational Techniques In Determination Of Dynamic Properties Of Agricultural Products-State Of The Arton Of Vibrational Techniques In Determination Of Dynamic Properties Of Agricultural Products-State Of The Art, Silas Kajuna

Tanzania Journal of Engineering and Technology (TJET)

Vibration is one of the techniques employed in the determination of dynamic properties of fruits and vegetables. It entails generation of a mechanical or acoustic vibrational signal which is propagated through the flesh of the agricultural material. A transducer is either attached or held close to the specimen to monitor the propagation of the signal through the specimen. The manner in which the signal is transmitted through the material is analyzed, and the dynamic properties of the specimen which relate to its firmness or its internal being are derived. The technique has been around for the past 30 years or …

Ole Miss Engineer 1999

Ole Miss Engineer

No abstract provided.

Ole Miss Engineer 1999

Ole Miss Engineer

No abstract provided.

Finite Element Simulation Of Creep Buckling Of Cipp Liners Under External Pressure, Qiang Zhao

Doctoral Dissertations

The problem of long-term structural behavior of CIPP liners under external hydrostatic pressure has been characterized as a structural instability problem which is induced by time-dependent material deformation or creep. It is also a contact problem since the liner deflection is externally constrained by the host pipe. The intrinsically nonlinear problem is investigated by means of finite element simulation, with emphases on (a) the essential structural behaviors and mechanisms of buckling, and (b) the influences of inelastic material properties (i.e. yield strengths and creep rates) and geometrical parameters on liner's buckling resistance.

A liner first deforms as a free pipe …

Micro Hydro Power, Frederick J. Munster

Maine Collection

Micro Hydro Power

by Frederick J. Munster

Department of Economic and Community Development, August, Me. 1999 (?).

Contents: Introduction / History of Hydropower in Maine / Renewables / Why Micro Hydro / Determining Flow / Determining Head / Estimating Energy Potential / Hydro Turbines / Dams, Impoundments, Penstocks and Power Houses / Utility Interconnected Systems / Battery Charging Systems / Operation and Maintenance / Economics / Regulation of Hydro Development / For More Information / References

Bolt Bearing Behavior Of Engineered Wood Composites, Stephen J. Carstens, David Pollock

Faculty Publications - Biomedical, Mechanical, and Civil Engineering

The goal of this research was to gain a better understanding of the bolt bearing behavior of engineered wood composites made from yellow poplar lumber. Lumber specimens included in this study were laminated veneer lumber, strandbased lumber, yellow poplar lumber, and Douglas-fir larch lumber. Testing followed the half-hole and full-hole configuration as set forth in ASTM Standard D5764 (1998).

In a previous study by Wilkinson (1991), a strong correlation was shown between bearing strength perpendicular to grain and bolt diameter. This study supports Wilkinson's finding for bearing strength perpendicular-to-grain based on the half hole test configuration. Other findings in this …

Ole Miss Engineer 1998

Ole Miss Engineer

No abstract provided.

Ole Miss Engineer 1998

Ole Miss Engineer

No abstract provided.

Lateral Resistance Of Ring-Shank Nail Connections In Southern Pine Lumber, R D. Theilen, D A. Bender, David Pollock, S G. Winistorfer

Faculty Publications - Biomedical, Mechanical, and Civil Engineering

Ring-shank nails are used in engineered structures with lateral connection design values based on theoretically derived equations which were validated only for common nails. The goal of this study was to quantify the input parameters and lateral connection strength of several types of ring-shank nails in Southern Pine lumber and critically evaluate the applicability of the theoretical equations for ring-shank nails.

Two sizes of galvanized and ungalvanized, hardened steel ring-shank nails from two manufacturers were studied. The hardened, ring-shank nails carried significantly higher loads than the common wire nails studied. Because the current method of determining yield load does not …

Maine Guide To Energy Efficient Residential Construction : A Manual Of Accepted Practices, State Of Maine Energy Conservation Division

Maine Collection

Maine Guide to Energy Efficient Residential Construction : A Manual of Accepted Practices

State of Maine Energy Conservation Division, Department of Economic and Community Development, 59 State House Station, Augusta, Maine 04333-0059

Second Edition - November, 1997

Contents: Dedication / Acknowledgements / Introduction / Part 1. Summary of Maine's Residential Energy Standards / Part 2. Siting and Initial Design Considerations / Part 3. Important Considerations for the Design Phase / Part 4. Recommended Construction Practices / Appendixes

Ole Miss Engineer 1997

Ole Miss Engineer

No abstract provided.

The Study Of Wave-Blocking And Current Effects On Nonlinear Interactions Of Shallow-Water Waves Using Advanced Boussinesq Models, Qin Chen

Civil & Environmental Engineering Theses & Dissertations

The first part of this work focuses on the derivation of enhanced Boussinesq-type equations for the combined motion of waves and currents in shallow water areas.

The strategy proposed in this work is to couple two known methods which are the sponge layer concept suitable for short waves and Sommerfeld radiation condition for currents. This coupling method provides satisfactory non-reflective boundaries for the simulation of fully coupled wave/current motion as demonstrated by the numerical experiments. We verify the model against the well known solutions based on the existing theories and good agreement has been observed. The numerical results confirm the …

Ole Miss Engineer 1997

Ole Miss Engineer

No abstract provided.

Withdrawal Strength Of Ring-Shank Nails Embedded In Southern Pine Lumber, M J. Skulteti, D A. Bender, S G. Winistorfer, David Pollock

Faculty Publications - Biomedical, Mechanical, and Civil Engineering

Ring-shank nails are used extensively in post-frame construction due to their superior performance, yet surprisingly little testing has been done on nail sizes above 12d. Experience in the post-frame industry suggests that published allowable design values for ring-shank nails may be overly conservative and need revision. The goal of the research reported herein was to characterize the withdrawal strength of ring-shank nails embedded in Southern Pine lumber. Three sizes ofgalvanized and ungalvanized (bright) ring-shank nails from two manufacturers were studied. Ring-shank nails had approximately twice the withdrawal resistance of smooth-shank nails of the same diameter. Galvanizing slightly reduced withdrawal strength …

A Design Of A Marine Radar Mast System For Minimum Vibration, Suey-Yueh Hu

Dissertations and Theses @ UNI

This experimental research focused on four areas: (a) the design of a new procedure for imitating the dynamic behavior of an electronic base plate on a radar mast system; (b) determination of a reasonable oscillation modal state; (c) avoidance of the destruction of the ability of the radar on the mast of a ship to receive and analyze incoming signals; and (d) design of a vibration absorber and vibration isolator based on an oscillation frequency. An adapted design for the vibration absorber and vibration isolator contributed to the prevention of excessive amplitude being produced by random forces acting upon a …

Ole Miss Engineer 1996

Ole Miss Engineer

No abstract provided.

The Crash Simulation And Analysis Of The Friendly Mobile Barrier, Bryan Edward Marz

Mechanical & Aerospace Engineering Theses & Dissertations

Mass transportation is an ever increasing alternative being researched and evaluated in today's society. With the increase of demand for such transportation, an increase in safety is also needed. This research entails the analysis of a new idea, The Friendly Mobile Barrier, in railroad crossing barrier design. The design is meant to prevent any approaching vehicle from crossing a railroad track and be survivable for those impacting the barrier.

Research conducted involves the crash simulation and analysis of the Friendly Mobile Barrier. The Friendly Mobile Barrier was analyzed structurally using finite element analysis. An advanced lumped-mass mathematical model software, Crash …

Energy Use Analysis Of A Multi-Unit Housing Facility A Parametric Study, Brian David Cooper

Mechanical & Aerospace Engineering Theses & Dissertations

In the continuing effort to reduce the energy use of buildings, design engineers and architects are called upon to design facilities which are more efficient and use less energy. The prediction of the energy used by a building's systems and occupants, for different design options and combinations, is an important part of the design of an energy efficient building.

An energy use analysis was conducted to determine the accuracy of a computerized building energy analysis simulation when only preliminary design information is available. Additional studies were made to determine the accuracy of the simulation as more detailed design, construction and …