Mechanical Engineering Commons^™

Building Fire Safety Audit At Faculty X, University Of Indonesia, Year 2006, Fatma Lestari, Rm. Yodan Amaral Panindrus

Makara Journal of Technology

Building Fire Safety Audit at Faculty X, University of Indonesia, Year 2006. Fire may cause loss of life, material and valuable assets. The objective of this study is to conduct audit for fire safety and emergency response in the building at Faculty X, University of Indonesia, Depok. The audit results on the building fire safety facilities including emergency response and preparedness are then compared to the Building Code Australia (BCA) and Indonesian regulation on the building fire safety (Kep.MenPU.No 10 and 11/KPTS/2000). The building selected are Building A, B, C, D, F and G. Building classification for A, B, D, …

Ad Hoc On-Demand Distance Vector (Aodv) Routing Protocol Performance Evaluation On Hybrid Ad Hoc Network: Comparison Of Result Of Ns-2 Simulation And Implementation On Testbed Using Pda, Riri Fitri Sari, Abdusy Syarif, Bagio Budiardjo

Makara Journal of Technology

Ad Hoc on-Demand Distance Vector (AODV) Routing Protocol Performance Evaluation on Hybrid Ad Hoc Network: Comparison of Result of Ns-2 Simulation and Implementation on Testbed using PDA. In Mobile Ad hoc NETwork (MANET), node supplemented with wireless equipment has the capacity to manage and organise autonomously, without the presence of network infrastructures. Hybrid ad hoc network, enable several nodes to move freely (mobile) to create instant communication. Independent from infrastructure. They could access the Local Area Network (LAN) or the Internet. Functionalities of ad hoc network very much dependent on the routing protocol that determines the routing around node. Ad …

Biomass Production Chlorella Vulgaris Buitenzorg Using Series Of Bubble Column Photo Bioreactor With A Periodic Illumination, Anondho Wijanarko, Dianursanti Dianursanti, Muryanto Muryanto, Josia Simanjuntak, Praswasti Pembangun Dyah Kencana Wulan, Heri Hermansyah, Misri Gozan, Roekmijati Widaningroem Soemantojo

Makara Journal of Technology

Chlorella vulgaris Buitenzorg cultivation using three bubble column photo bioreactors arranged in series with a volume of 200 mL for 130 hours shows an increase of biomass production of Chlorella vulgaris Buitenzorg up to 1.20 times and a decrease of the ability of CO2 fixation compared to single reactor at a periodic sun illumination cycle. The operation conditions on cultivation are as following: T, 29.0oC; P,1 atm.; UG, 2.40 m/h; CO2, 10%; Benneck medium; and illumination source by Phillip Halogen Lamp 20W /12V/ 50Hz. Other research parameters such as microbial carbon dioxide transferred rate (qco2), CO2 transferred rate (CTR), energy …

The Effect Of Ozone And Zeolite Concentration To The Performance Of The Treatment Of Wastewater Containing Heavy Metal Using Flotation Process, Eva Fathul Karamah, Setijo Bismo, Hotdi M. Simbolon

Makara Journal of Technology

The Effect of Ozone and Zeolite Concentration to the Performance of the Treatment of Wastewater Containing Heavy Metal Using Flotation Process. Industrial wastewater which contains heavy metal cannot be disposed to the environment directly, due to its toxicity. In this research, separation of metal from wastewater was conducted by sorptive flotation method, using Lampung natural zeolite as bonding agent. The most common diffuser used in the flotation process is air or oxygen. In this research, ozone is used as diffuser because it is a stronger oxidant and more dissolvable in water than oxygen. Besides, ozone is a coagulant aid and …

The Role Of 1 And 9 Wt.% Zn In Precipitation Hardening Of Aa319 Aluminium, Bondan Tiara Sofyan, Sari Susanti, Ridwan R. Yusfranto

Makara Journal of Technology

The Role of 1 and 9 wt.% Zn in Precipitation Hardening of AA319 Aluminium. Aluminium alloys are widely used for automotive application due to its low density and high corrosion resistance. For economic reason, casting of automotive products always uses aluminium scrap as charging materials that may result in fluctuation of content of alloying element, such as Zn. This research studies the role of Zn in precipitation hardening of AA319 aluminium alloys. Hardness and tensile testing were conducted to study the mechanical properties of the alloys, while ageing response was followed by hardness measurements. Evolution of microstructures was observed by …

Parallel Mpi/Fortran Finite Element Symmetrical/Unsymmetrical Domain Decomposition, Siroj Tungkatara

Civil & Environmental Engineering Theses & Dissertations

MPI/FORTRAN finite element analysis software based on Domain Decomposition (DD) formulas has been developed in this work. Efficient input data storage/data communication schemes, domain partitioning, fast symbolical and numerical sparse assembly, symmetrical/unsymmetrical sparse solver and robust symmetrical/unsymmetrical iterative solvers algorithms are all incorporated into the developed code. Parallel Precondition Conjugated Gradient (PCG) and Flexible Generalized Minimum Residual (FGMRES) are developed. Efficient computational techniques used in the developed code are explained. Numerical performance and the accuracy of the developed code are conducted on acoustic examples with medium to large grid sizes. The results obtained from ODU Wilbur cluster (under parallel processing …

Development And Validation Of A Dynamic Model Of The Maglev Transportation System At Old Dominion University, Ajinkya Deodhar, Sebastian Bawab, Aravind Hanasoge

Mechanical & Aerospace Engineering Faculty Publications

A dynamic model of the vehicle/guideway coupled with a controller is developed for the maglev demonstration system currently being developed at ODU, using the MAthematical DYnamic MOdeling software - MADYMO. The fundamental characteristics of the vehicle and guideway are obtained from detailed finite element analyses using MSC-NASTRAN. As a result, the vehicle is modeled in MADYMO as a 21- degree-of-freedom spring-mass-damper system. A three span concrete guideway is modeled using 3D solid Hex8 elements. The air gap is modeled as a penetration of the magnets into the guideway. Decentralized colocated PD controllers are used for controlling the penetration of each …

Comparison Of Roadside Crash Injury Metrics Using Event Data Recorders, Doug Gabauer, Hampton C. Gabler

Faculty Journal Articles

The occupant impact velocity (OIV) and acceleration severity index (ASI) are competing measures of crash severity used to assess occupant injury risk in full-scale crash tests involving roadside safety hardware, e.g. guardrail. Delta-V, or the maximum change in vehicle velocity, is the traditional metric of crash severity for real world crashes. This study compares the ability of the OIV, ASI, and delta-V to discriminate between serious and non-serious occupant injury in real world frontal collisions. Vehicle kinematics data from event data recorders (EDRs) were matched with detailed occupant injury information for 180 real world crashes. Cumulative probability of injury risk …

College Of Engineering Senior Design Competition Fall 2007, University Of Nevada, Las Vegas

Fred and Harriet Cox Senior Design Competition Projects

Part of every UNLV engineering student’s academic experience, the senior design project stimulates engineering innovation and entrepreneurship. Each student in their senior year chooses, plans, designs, and prototypes a product in this required element of the curriculum. A capstone to the student’s educational career, the senior design project encourages the student to use everything learned in the engineering program to create a practical, real world solution to an engineering challenge.

The senior design competition helps to focus the senior students in increasing the quality and potential for commercial application for their design projects. Judges from local industry evaluate the projects …

Trajectory Shaping Of Surface-To-Surface Missile With Terminal Impact Angle Constraint, S. Subchan

Makara Journal of Technology

This paper presents trajectory shaping of a surface-to-surface missile attacking a fixed with terminal impact angle constraint. The missile must hit the target from above, subject to the missile dynamics and path constraints. The problem is reinterpreted using optimal control theory resulting in the formulation of minimum integrated altitude. The formulation entails nonlinear, two-dimensional missile flight dynamics, boundary conditions and path constraints. The generic shape of optimal trajectory is: level flight, climbing, diving; this combination of the three flight phases is called the bunt manoeuvre. The numerical solution of optimal control problem is solved by a direct collocation method. The …

Limiting Maximum Drag Reduction Asymptote For The Moment Coefficient Of An Enclosed Rotating Disk With Fine Spiral Grooves, Budiarso Budiarso, Keizo Watanabe, Satoshi Ogata

Makara Journal of Technology

In this study, the limiting maximum drag reduction asymptote for the moment coefficient of an enclosed rotating disk with fine spiral grooves in turbulent flow region were obtained analytically. Analysis which were based on an assumption for a simple parabolic velocity distribution of turbulent pipe flow to represent relative tangential velocity, was carried out using momentum integral equations of the boundary layer. For a certain K- parameter the moment coefficient results agree well with experimental results for maximum drag reduction in an enclosed rotating disk with fine spiral grooves and drag reduction ratio approximately was 15 %. Additionally, the experimental …

Co2 Absorption From Its Mixture With Ch4 Or N2 Through Hollow Fiber Membrane Contactor Using Water As Solvent, Sutrasno Kartohardjono, Anggara Anggara, Subihi Subihi, Yuliusman Yuliusman

Makara Journal of Technology

CO2 Absorption from Its Mixture with CH4 or N2 through Hollow Fiber Membrane Contactor using Water as Solvent. Hollow fiber membrane contactors have been widely used as gas-liquid contactors recently such as in the CO2 absorption process from gas stream. This research aims to evaluate the effectiveness of hollow fiber membrane contactor to absorb CO2 from its mixture with CH4 or N2 using water through mass transfer and hydrodynamic tests. There are 3 membrane modules used in this research with shell diameter of 1.9 cm, length of 40 cm, outer fiber diameter of 2.7 mm and fiber number in the …

Reverse Link Cdma System Capacity Evaluation For Stratospheric Platform Mobile Communications, Iskandar Iskandar

Makara Journal of Technology

We propose an analysis of reverse link CDMA multispot beam stratospheric platforms (SPF) in this paper. The SPF is currently proposed as a novel wireless technology for the development of the next generation fixed and mobile communications. The geometry of this technology is different from that of the terrestrial but rather similar to the satellite based cellular system. However, evaluation on the CDMA system capacity of this technology has not been much reported. This paper addresses all possible multiple access interference analyses including the effects of channel fading and shadowing in order to evaluate the system capacity. Single SPF and …

The Potency Of Fire And Explosion Hazard On Premium Oil Storage Tank At Depot X 2007, Fatma Lestari, Warid Nurdiansyah

Makara Journal of Technology

The Potency of Fire and Explosion Hazard on Premium Oil Storage Tank at Depot X 2007. Premium oil storage tanks have fire and explosion risk because Premium oil is flammable liquid. Because of that, fire and explosion risk assessment on Premium oil storage tank at Depot X is needed as foundation to fire and explosion risk management, and comply with regulations. Method of this research is Dow’s Fire and Explosion Index. This research indicate that F&EI value for Premium oil storage tank is 118,82. Based on that F&EI value, level of risk at Premium oil storage tank is intermediate risk.

Analysis Of Three Phase Controlled Rectifier With The Same Distance Control As Compared To The Same Angle Control, Sudirman S., Sri Kurniati A.

Makara Journal of Technology

Analysis of three phase controlled rectifier with the same distance control as compared to the same angle control. This research aim to compare the firing of the same distance and the same angle control at three phase controlled rectifier with seen generated harmonic at input (AC side). Then calculate of rectifier efficiency and power factor comparison from both the control type. The rectifier use passive filter with resistance 11 ohm and is analysed with program simulation using PSPICE version 7.1. Result of research indicate that use of the same distance control generates the 5th and 7th harmonics, while the same …

The Use Of Red Cabbage’S Anthocyanine Extract As A Photosensitizer On A Dye-Sensitized Nanocrystalline Tio2 Solar Cell, Akhiruddin Maddu, Mahfuddin Zuhri, Irmansyah Irmansyah

Makara Journal of Technology

The use of Red Cabbage’s anthocyanine extract as a photosensitizer on a Dye-Sensitized Nanocrystalline TiO2 Solar Cell. A solid-state dye-sensitized nanocrystalline TiO2 solar cell utilizing anthocyanin extract form red cabbage as photosensitizer was fabricated. The solar cell was formed in sandwich structure, which two electrodes sandwiching polymer electrolyte containing a redox couple (I-/I3 -). One of the electrodes, namely working electrode, TiO2 layer on TCO (transparent conducting oxide) coated glass substrate was sensitized with anthocyanin dye as electron donor in the system. Another electrode was a carbon sheet as a counter electrode. Gel electrolyte based on PEG (polyethylene glycol) containing …

Effect Of Contact Time On Interface Reaction Between Aluminum Silicon (7% And 11%) Alloy And Steel Dies Skd 61, Bambang Suharno, Neni Octapiani Nurhayati, Bustanul Arifin, Sri Harjanto

Makara Journal of Technology

Effect of Contact Time on Interface Reaction between Aluminum Silicon (7% and 11%) Alloy and Steel Dies SKD 61. Die soldering (die sticking) is a defect of metal casting in which molten metal “welds” to the metallic die mold surface during casting process. Die soldering is the result of an interface reaction between the molten aluminum and the die material. Aluminum alloy with 7 and 11% silicon and SKD 61 die steel are the most common melt and die material used in aluminum die casting. This research is done to study the morphology and the characteristics of the formed AlxFeySiz …

Ole Miss Engineer 2007

Ole Miss Engineer

No abstract provided.

Comparing The Feasibility Of Cutting Thin-Walled Sections From Five Commonly Used Metals Utilizing Wire Electric Discharge Machining, Richard C. Stephenson

Theses and Dissertations

Wire Electric Discharge Machining (wire-EDM) is a non-traditional machining process. Controlled electric sparks are successively used to vaporize part of a workpiece along a programmed path in order to machine a desired part. Because there is no tool that comes in direct contact with the workpiece, it is possible to machine thin, delicate parts. This thesis was designed to observe and analyze the differences in cutting capabilities for a conventional wire-EDM machine when cutting thin-walled sections from five commonly used metals utilizing a variation of roughing and finishing passes. The five metals that were used in this study are: Aluminum …

Friction Stir Welding Of High-Strength Automotive Steel, Eric Michael Olsen

Theses and Dissertations

The following thesis is a study on the ability to create acceptable welds in thin-plate, ultra-high-strength steels (UHSS) by way of friction stir welding (FSW). Steels are welded together to create tailor-welded blanks (TWB) for use in the automotive industry. Dual Phase (DP) 590, 780, and 980 steel as well as Transformation-Induced Plasticity (TRIP) 590 steel with thicknesses ranging from 1.2 mm to 1.8 mm were welded using friction stir welding under a variety of processing conditions, including experiments with dissimilar thicknesses. Samples were tested under tensile loads for initial determination if an acceptable weld had been created. Acceptable welds …

Reliability Of Concrete Masonry Unit Walls Subjected To Explosive Loads, Christopher D. Eamon

Civil and Environmental Engineering Faculty Research Publications

This study discuses the development of a procedure that can be used to assess the reliability of concrete masonry unit infill walls subjected to personnel-delivered blast loads. Consideration is given to maintain reasonable computational effort for both the structural analysis and reliability models. Blast load and wall resistance models are developed based on experimental and analytical data, and resistance is evaluated with a large strain, large displacement transient dynamic finite element analysis. A sensitivity analysis is conducted to identify significant random variables and a reliability analysis conducted with a feasible level of computational effort. Reliability indices are estimated for two …

Civil And Mechanical Engineering Students Learning Mechanics In A Multidisciplinary Engineering Foundation Spiral, Jean Nocito-Gobel, Gregory Broderick, Samuel Bogan Daniels, Michael Collura, Richard Stanley

Engineering and Applied Science Education Faculty Publications

This paper describes how mechanical and civil engineering students are introduced to and develop an understanding of mechanics concepts through a sequence of integrated courses as part of a new curriculum taken during the freshman and sophomore years. The Multi- Disciplinary Engineering Foundation Spiral is a four-semester sequence of engineering courses, matched closely with the development of students’ mathematical sophistication and analytical capabilities and integrated with course work in the sciences. Students develop a conceptual understanding of engineering basics in this series of courses, which stress practical applications of these principles. Mechanics concepts are introduced in a pair of first …

Development And Evaluation Of A Simulation System Based Upon Standard Pedestrian Thoroughfare Methodologies, Charles O. Pringle

All Master's Theses

This study was undertaken to determine whether existing simulation and modeling systems could be used to analyze and model pedestrian traffic flows. The study incorporates the Highway Capacity Manual 2000 (HCM) (Transportation Research Board, National Research Council [TRB], 2000a) methodologies into a ProModel simulation and then compares and contrasts the results of the HCM calculations with the ProModel simulation.

College Of Engineering Senior Design Competition Spring 2007, University Of Nevada, Las Vegas

Fred and Harriet Cox Senior Design Competition Projects

Part of every UNLV engineering student’s academic experience, the senior design project stimulates engineering innovation and entrepreneurship. Each student in their senior year chooses, plans, designs, and prototypes a product in this required element of the curriculum. A capstone to the student’s educational career, the senior design project encourages the student to use everything learned in the engineering program to create a practical, real world solution to an engineering challenge.

The senior design competition helps to focus the senior students in increasing the quality and potential for commercial application for their design projects. Judges from local industry evaluate the projects …

Observations Of Structural Damage Caused By Hurricane Katrina On The Mississippi Gulf Coast, Christopher D. Eamon, Patrick Fitzpatrick, Dennis D. Truax

Civil and Environmental Engineering Faculty Research Publications

The loads associated with Hurricane Katrina led to the destruction or severe damage of approximately 130,000 homes and over 200 deaths in the state of Mississippi. This paper discusses the results of a field inspection of structural damage along the state’s Gulf Coast area caused by this hurricane. It was found that reinforced concrete, steel frame, and heavy timber structures generally performed well, with minimal structural damage. Precast concrete, light frame wood, and bridge structures generally performed poorly. Non-structural components of all building types, in particular facades and interior partitions subjected to storm surge, were typically destroyed. For various structures, …

Ole Miss Engineer 2007

Ole Miss Engineer

No abstract provided.

Uncertainty And Error In Laser Triangulation Measurements For Pipe Profiling, Michael Kenneth Swanbom

Doctoral Dissertations

Underground pipeline infrastructure often receives insufficient attention and maintenance. Those responsible for ensuring the continuing functionality of this infrastructure primarily use subjective information in their decision making, and standards defining the level of damage acceptable before repair or replacement are difficult to implement. Laser pipe profiling is a relatively new technology that has emerged to take a step toward the objective assessment of buried assets. A laser profiler is a device that traverses a section of pipe, taking measurements of radius around the circumference of the inner pipe wall at multiple locations along the length of the pipe. The accuracy …

Biodesulphurization Within Natural Gas In Oil And Gas Field, Sri Astuti Rahayu, M. Fierdaus, Syafrizal Syafrizal, M. Udiharto

Makara Journal of Technology

The presence of sulphur compounds in natural gas can interfere to the quality of natural gas. The decline of combustion gas capacity, metal instrument corrosion in gas piping, and the environmental pollution from gas emission can affect by their presence. Bio-filter is one of the methods that selected to reduce sulphur content in natural gas. A lab scale study of hydrogen sulphide reduction in natural gas had conducted in oil and gas field using bio-filter method. The bio-filter system (±1 L volume) contains an active carbon and thiosulphide medium as a substrate, Thiobacillus thioparus as a single culture of sulphur …

Mechanical Study On Using Of Accr Thermal Conductor At 500 Kv Sutet, Suprihadi Prasetyono

Makara Journal of Technology

Mechanical Study on using of ACCR Thermal Conductor at 500 kV SUTET. At the height of electricity demand increasing recently, circumstance of environment more limited and also expense of high investment, making thermal conductor (conductor thermal resistance) considered to be one of alternative in the electricity transmission bottlenecks. These days it has been developed thermal conductor ACCR (Aluminium Conductor Composite Reinforced) which can operate with temperature up to 240oC, so that making the current carrying capacity being higher than conventional conductor. This research aimed to study load current leading to mechanical characteristic ACCR conductor included tension, length of elongation and …

Production Of Medium Chain Length Polyhydroxyalkanoates From Oleic Acid Using Pseudomonas Putida Pga1 By Fed Batch Culture, Sidik Marsudi, Irene K.P. Tan, Seng Neon Gan, K. B. Ramachandran

Makara Journal of Technology

Bacterial polyhydroxyalkanoates (PHAs) are a class of polymers currently receiving much attention because of their potential as renewable and biodegradable plastics. A wide variety of bacteria has been reported to produce PHAs including Pseudomonas strains. These strains are known as versatile medium chain length PHAs (PHAs-mcl) producers using fatty acids as carbon source. Oleic acid was used to produce PHAs-mcl using Pseudomonas putida PGA 1 by continuous feeding of both nitrogen and carbon source, in a fed batch culture. During cell growth, PHAs also accumulated, indicating that PHA production in this organism is growth associated. Residual cell increased until the …