Mechanical Engineering Commons^™

Fundamental Studies Of Flame Propagation In Lean-Burn Natural Gas Engines, Zhiyan Wang

Open Access Dissertations

Lean-burn natural gas engines offer enhanced thermal efficiencies and reduced soot and NOx emissions. However, cycle-to-cycle variability in combustion that can result from unreliable ignition, variability in equivalence ratio and quenching is a challenge. Reliability of ignition can be improved by employing a dual-fuel ignition strategy in which a small quantity of diesel fuel is injected to initiate ignition. Computational studies of n-heptane/methane-air mixing layers are performed to provide insight into the fundamental physics of dual-fuel ignition. The results show that the characteristic time required for steady premixed flame propagation has three components: time for autoignition to occur, time for …

Determination Of Aqueous Surfactant Solution Surface Tensions With A Surface Tensiometer, Remelisa Esteves, Birce Dikici Ph.D, Matthew Lehman, Qayyum Mazumder, Nonso Onukwuba

Beyond: Undergraduate Research Journal

Surfactant solutions are applicable to engineering systems for cooling equipment for electronics. Surfactants can be added to water to improve heat transfer. An application of using aqueous surfactant solutions can be through microchannel heat sink. Although it is ideal to redesign these systems to reduce heat, it is a costly method. Surfactant solutions at optimal solution concentration can be able to transfer heat quickly and effectively with minimum expense. The surface tension of surfactant solutions is an important parameter for boiling heat transfer and must be taken into consideration. The purpose of this research is to measure surface tension of …

Determination Of Surfactant Solution Viscosities With A Rotational Viscometer, Remelisa Esteves, Nonso Onukwuba, Birce Dikici Ph.D

Beyond: Undergraduate Research Journal

Aqueous surfactant solutions are used in engineering systems for improving boiling heat transfer. The purpose of this research is to determine the viscosities of surfactant solutions and to investigate the effect of composition on viscosity. The results obtained can possibly be used as reference for further study in the effects of surfactant solution viscosities on nucleate boiling. A rotational viscometer was used to determine the viscosities of three surfactant solutions – SLS, EH-14, and SA-9 – of various compositions at room temperature. It was discovered that the viscosities of SLS, EH-14, and SA-9 had a nearly consistent pattern as their …

Peridynamic Modeling Of Ruptures In Biomembranes, Michael Taylor, Irep Gözen, Samir Patel, Aldo Jesorka, Katia Bertoldi

Mechanical Engineering

We simulate the formation of spontaneous ruptures in supported phospholipid double bilayer membranes, using peridynamic modeling. Experiments performed on spreading double bilayers typically show two distinct kinds of ruptures, floral and fractal, which form spontaneously in the distal (upper) bilayer at late stages of double bilayer formation on high energy substrates. It is, however, currently unresolved which factors govern the occurrence of either rupture type. Variations in the distance between the two bilayers, and the occurrence of interconnections (“pinning sites”) are suspected of contributing to the process. Our new simulations indicate that the pinned regions which form, presumably due to …

Numerical Simulation On The Combustion Characteristic Of Iron Ore Sintering With Flue Gas Recirculation, Gan Wang, Zhi Wen, Guofeng Lou, Ruifeng Dou, Xunliang Liu, Fuyong Su, Sizong Zhang

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Modelling Of Coal-Biomass Blends Gasification And Power Plant Revamp Alternatives In Egypt’S Natural Gas Sector, Dalia A. Ali Eng, Mamdouh A. Gadalla Prof., Omar Y. Abdelaziz, Fatma H. Ashour Prof.

Chemical Engineering

Recently, there has been a growing research interest in the co-gasification of biomass with coal to produce syngas and electricity in a sustainable manner. Co-gasification technology do not only decrease potentially the exploitation of a significant amount of conventional coal resources, and thus lower greenhouse gases (GHG) emissions, but also boost the overall gasification process efficiency. In the present work, a rigorous simulation model of an entrained flow gasifier is developed using the Aspen Plus® software environment. The proposed simulation model is tested for an American coal and the model validation is performed in good agreement with practical data. The …

Modeling Pyrolysis Of Large Coal Particles With Many Species, Jianqing Li

Master's Theses (2009 -)

Coal currently supplies 40% of the world’s electricity needs, and is one of the most important energy sources. As the initial stage of coal combustion, pyrolysis is a thermal decomposition process which converts coal into light gases and tars, which are subsequently consumed in combustion reactions, as well as solid char. Recently there has been interest in using slow pyrolysis as a stand-alone process for the production of chemicals and fuels from large (mm-scale) coal particles. Simulations can be used to efficiently study the impact of pyrolysis conditions on gas, tar and char yields, as well as gas and tar …

Computational Fluid Dynamics Modeling And Simulations Of Fluidized Bed Reactors For Chemical Looping Combustion, Subhodeep Banerjee

McKelvey School of Engineering Graduate Student Theses & Dissertations

Chemical looping combustion (CLC) is a next generation combustion technology that shows great promise as a solution for the need of high-efficiency low-cost carbon capture from fossil fueled power plants. To realize this technology on an industrial scale, the development of high-fidelity simulations is a necessary step to develop a thorough understanding of the CLC process. Although there have been a number of experimental studies on CLC in recent years, CFD simulations have been limited in the literature.

In this dissertation, reacting flow simulations of a CLC reactor are developed using the Eulerian approach based on a laboratory-scale experiment of …

Study On Oil Palm Fresh Fruit Bunch Bruise In Harvesting And Transportation To Quality, Andreas Wahyu Krisdiarto, Lilik Sutiarso

Makara Journal of Technology

There are losses of production due to oil palm field’s material handling. Activities that may raise the losses are harvesting and transportation, which may cause bruise and damage to fruit. This research was aimed to learn the bruise of fresh fruit bunch (FFB) phenomenon in harvesting and transportation. Method used in this research was measuring the bruise area resulted by FFB falling when harvested, loading (throwing up) FFB to truck bin, and transporting using truck. These data, coupled with weight of bruised fruit, were calculated to get FFB bruise index. Each FFB bruise index is related to potential free fatty …

Automatic Arrhythmia Beat Detection: Algorithm, System, And Implementation, Wisnu Jatmiko, I Md. Agus Setiawan, Muhammad Ali Akbar, Muhammad Eka Suryana, Yulistiyan Wardhana, Muhammad Febrian Rachmadi

Makara Journal of Technology

Cardiac disease is one of the major causes of death in the world. Early diagnose of the symptoms depends on abnormality on heart beat pattern, known as Arrhythmia. A novel fuzzy neuro generalized learning vector quantization for automatic Arrhythmia heart beat classification is proposed. The algorithm is an extension from the GLVQ algorithm that employs a fuzzy logic concept as the discriminant function in order to develop a robust algorithm and improve the classification performance. The algorithm is tested against MIT-BIH arrhythmia database to measure the performance. Based on the experiment result, FN-GLVQ is able to increase the accuracy of …

Optimization Of Electricity Generation Schemes In The Java-Bali Grid System With Co2 Reduction Consideration, Farizal Farizal, Wenty Eka Septia, Amar Rachman, Nasruddin Nasruddin, Teuku Meurah Indra Mahlia

Makara Journal of Technology

This research considers the problem of reducing CO2 emissions from the Java-Bali power grid system that consists of a variety of power-generating plants: coal-fired, natural gas, oil, and renewable energy (PV, geothermal, hydroelectric, wind, and landfill gas). The problem is formulated as linear programming and solved using LINGO 10. The model was developed for a nation to meet a specified CO2 emission target. Two carbon dioxide mitigation options are considered in this study, i.e. fuel balancing and fuel switching. In order to reduce the CO2 emissions by 26% in 2021, State Electric Supply Company (PLN) has to generate up to …

Apparent Porosity And Compressive Strength Of Heat-Treated Clay/Iron Sand/Rice Husk Ash Composites Over A Range Of Sintering Temperatures, M. Nizar Machmud, Zulkarnain Jalil, Mochammad Afifuddin

Makara Journal of Technology

Novel composites of clay/iron sand/rice husk ash (RHA) have been developed. Electric furnace was used to perform heat treatment on the composites to study the effect of sintering temperature on their apparent porosity and compressive strength. Two types of RHA with different bulk density were prepared to gain an understanding of the influence of apparent porosity on compressive strength of the heat-treated composites over a range of sintering temperatures. Heattreated composites, made of clay/iron sand and clay/RHA, were also prepared as a referenced material. X-ray diffraction (XRD) analysis was further performed to comprehensively discuss the role of iron sand on …

The Effect Of Irradiation Of Fe And Ar Ion On The Surface Morphology Of Diamond Thin Film Related To The Magnetoresistance Property, Salim Mustofa, Setyo Purwanto, Kenji Mishima

Makara Journal of Technology

The irradiation of Fe and Ar ion was applied on the surface of diamond/Si thin film to know its effect on the morphology of thin film.The magnetoresistance property was also studied. Ion irradiation treatment using Fe ion followed by argon ion at the energy of 70keV and a dose of 1 x 1015 ion/cm2 have been conducted on the surface of two types of thin film, diamond/Si (111) and diamond/Si (100). Both thin films were made by using a CVD method, and the thickness of the thin film is 1000-nm. From simulations using the software called Stopping and Range of …

Use Of Green Mussel Shell As A Desulfurizer In The Blending Of Low Rank Coal-Biomass Briquette Combustion, Mahidin Mahidin, Asri Gani, M. Reza Hani, Muhammad Syukur, Hamdani Hamdani, Khairil Khairil, Samsul Rizal, Abdul Hadi, T.M.I. Mahlia

Makara Journal of Technology

Calcium oxide-based material is available abundantly and naturally. A potential resource of that material comes from marine mollusk shell such as clams, scallops, mussels, oysters, winkles and nerites. The CaO-based material has exhibited a good performance as the desulfurizer or adsorbent in coal combustion in order to reduce SO2 emission. In this study, pulverized green mussel shell, without calcination, was utilized as the desulfurizer in the briquette produced from a mixture of low rank coal and palm kernel shell (PKS), also known as bio-briquette. The ratio of coal to PKS in the briquette was 90:10 (wt/wt). The influence of green …

The Knowledge-Based Analysis On Medium Resolution Images Of Remote Sensing To Extraction Information Land Use Type Scs-Cn, The Case Study On Grompol Watershed, Puguh Dwi Raharjo, Totok Gunawan, Mohammad Pramono Hadi

Makara Journal of Technology

Remote sensing imagery Landsat-8 is one image that has a good temporal resolution; in addition to the availability of data, this image can be obtained free of charge. Land cover type SCS-CN is part of a unit of land that affects runoff. The use of medium resolution imagery in reducing the SCS-CN land use type is considered relatively difficult, and it yields less good accuracy. Limitations on multispectral classification only rely on facts derived from spectral reflection, so that the two data are the same since different characteristic results are not so good. This study aims to determine the accuracy …

Sugarcane Bagasse As A Carrier For The Immobilization Of Saccharomyces Cerevisiaein Bioethanol Production, Sita Heris Anita, Wibowo Mangunwardoyo, Yopi Yopi

Makara Journal of Technology

Sugarcane bagasse was used as a carrier to immobilize Saccharomyces cerevisiae in bioethanol production. This research aims to study the potential use of sugarcane bagasse as an alternative carrier for cell immobilization and improvement in the production process of cell immobilization in bagasse. The results showed that the physical characteristics of sugarcane bagasse as a carrier were water content (7.77 ± 0.35%), water retention (4.80 ± 0.44 g/g), water absorption index (8.58 ± 0.22 g/g), and lignin content (24.40 ± 1.52 %). Determination of cell retention was performed in an inoculum volume of 50 mL yeast suspension with various carrier …

Delay-Independent Stability Analysis Of Linear Time-Delay Systems Based On Frequency, Xianwei Li, Huijun Gao, Keqin Gu

SIUE Faculty Research, Scholarship, and Creative Activity

This paper studies strong delay-independent stability of linear time-invariant systems. It is known that delay-independent stability of time-delay systems is equivalent to some frequency-dependent linear matrix inequalities. To reduce or eliminate conservatism of stability criteria, the frequency domain is discretized into several sub-intervals, and piecewise constant Lyapunov matrices are employed to analyze the frequency-dependent stability condition. Applying the generalized Kalman–Yakubovich–Popov lemma, new necessary and sufficient criteria are then obtained for strong delay-independent stability of systems with a single delay. The effectiveness of the proposed method is illustrated by a numerical example.

Go With The Flow –Thermoelectric Energy, Shawn Bell

Middle School Lesson Plans

In this unit, students will learn how thermal energy be transferred and transformed. They will carry out investigations to gather evidence to support an explanation about direct conversion of heat into electrical energy. They will develop a model that shows the components of the system and changes in the system being investigated, and they will use evidence from the investigation to construct an explanation for how the energy flows.

Fluid Analysis In Solar Heat Pipes, Ben Krumholz, Michael Agavo, William Dundon

Mechanical Engineering

Evacuated tube solar collectors are efficient systems that use heat pipes to facilitate heat transfer. They use incoming solar radiation to heat water. Professor Mason Medizade tasked the team with choosing a component of the system to research and test its influence on system performance. The team investigated the working fluid that runs through the heat pipes. Distilled water, acetone, and ethanol at a range of fill volumes form 1 mL to 11 mL were tested. The team's goal was to find a volume for each fluid to maximize performance of the system. Performance was defined as average temperature rise …

Micro Debris Generator, Gordan Bradaric, Ross Byers, Stephen Quanci

Mechanical Engineering

This senior project team at Cal Poly consisting of Stephen Quanci, Gordan Bradaric, and Ross Byers has been commissioned by Erik Brown of Lawrence Livermore National Labs to create a way to reliably and consistently entrain microscopic particles into the hot HTTU flow. These particles will be used to compare the loading rates of new HEPA filters by measuring the pressure drop across the filter. The generated particles would simulate typical conditions in which these HEPA filters are expected to operate, namely fine ash. The particles used for loading the filter are intended to simulate the particulate reaching the LLNL …

Haul Truck Tires Recycling, Jessica N. Lizarazu

Chemical Engineering Undergraduate Honors Theses

The disposal of large Off-the-Road (OTR) tires is an increasingly important concern. These tires can weigh up to 8,450 pounds with an overall diameter and width of approximately 140.7 inches and 45.1 inches respectively. OTR tires are used for mining vehicles such as haul trucks, wheel loaders, backhoes, graders, and trenchers. These new tires cost between $38,000 and $50,000 each, depending on multiple factors including oil prices and the cyclical nature of the industry. Haul trucks contain six tires per vehicle, and mines replace these tires around every 9-12 months. Statistics regarding discarded OTR tires are not provided by the …

Particle Image Velocimetry Design & Installation, Zach Ritchie

Mechanical Engineering Undergraduate Honors Theses

This work will mainly focus on the design, construction, and installation of the Particle Image Velocimetry (PIV) system in the Chemical Hazards Research Center wind tunnel. The PIV system utilizes a Class IV (double pulsed) laser, optics to produce a light sheet, timing circuitry, and a high-resolution camera (with buffered output) to measure a system’s velocity (two-dimensional) field by determining the displacement of particles over the time between laser pulses. For maximum mobility and functionality, the PIV system was installed in the center of the tunnel on a moveable cart with the laser and camera mounted to an adjustable support. …

A Comparison Of American, Norwegian, And Russian Standards In Calculating The Wall Thickness Of Submarine Gas Pipeline, Cindy Dianita, Tatyana Vladimirovna Dmitrieva

Makara Journal of Technology

One of the key issues in the pipeline design is wall thickness calculation. This paper highlights a comparison of wall thickness calculation methods of submarine gas pipeline based on Norwegian Standard (DNV-OS-F101), Indonesian Standard SNI 3474 which refers to American Standard (ASME B31.8), and Russian Standard (VN39-1.9-005-98). A calculation of wall thickness for a submarine gas pipeline in Indonesia (pressure 12 MPa, external diameter 668 mm) gives the results of 18.2 mm (VN39-1.9-005-98), 16 mm (ASME B31.8), and 13.5 mm (DNV-OS-F101).The design formula of hoop stress due to internal pressure is interpreted in different ways for every standard. Only Norwegian …

Texture Analysis Using The Neutron Diffraction Method On The Non Standardized Austenitic Steel Process By Machining,Annealing, And Rolling, Tri Hardi Priyanto, Parikin Parikin, Meijuan Li

Makara Journal of Technology

Austenitic steel is one type of stainless steel which is widely used in the industry. Many studies on austenitic stainless steel have been performed to determine the physical properties using various types of equipment and methods. In this study, the neutron diffraction method is used to characterize the materials which have been made from minerals extracted from the mines in Indonesia. The materials consist of a granular ferro-scrap, nickel, ferro-chrome, ferro-manganese, and ferro-silicon added with a little titanium. Characterization of the materials was carried out in three processes, namely: machining, annealing, and rolling. Experimental results obtained from the machining process …

Thermal Properties, Crystallinity, And Oxygen Permeability Of Na-Montmorillonite Reinforced Plasticized Poly(Lactic Acid) Film, Kurniawan Yuniarto, Yohanes Aris Purwanto, Setyo Purwanto, Bruce A. Welt, Hadi Karia Purwadaria, Titi Candra Sunarti

Makara Journal of Technology

Introducing unmodified organically clay/Na-montmorillonite (Na-MMT) was applied into plasticized poly(lactic acid) PLA to produce film composites by direct casting. Film composite structure, the crystallinity degree and form, and thermal properties were carried out using X-ray diffraction and differential scanning calorimetry. The effect of Na- MMT to the tortuous path and the crystallinity degree in the plasticized film composites were calculated in oxygen barrier properties. Chromatogram film composites resulted in an intercalated structure that showed peak diffraction angle shift at about 0.2o. Then, a peak diffraction pattern was indicated in α-form crystal structure. Plasticized PLA has a crystallinity degree at 34%, …

Residual Strength Analysisof Asymmetrically Damaged Ship Hull Girderusing Beam Finite Element Method, Muhammad Zubair Muis Alie

Makara Journal of Technology

The objective of the present study is to analyze the residual strength of asymmetrically damaged ship hull girder under longitudinal bending. Beam Finite Element Method is used for the assessment of the residual strength of two single hull bulk carriers (Ship B1 and Ship B4) and a three-cargo-hold model of a single-side Panamax Bulk Carrier in hogging and sagging conditions. The Smith’s method is adopted and implemented into Beam Finite Element Method. An efficient solution procedure is applied; i.e. by assuming the cross section remains plane, the vertical bending moment is applied to the cross section and three-cargo-hold model. As …

Maneuverability Of Ships With Small Draught In Steady Wind, Daeng Paroka, Andi Haris Muhammad, Syamsul Asri

Makara Journal of Technology

Wind force and moment may force a ship to drastically decrease its speed and use a large drift angle as well as a large rudder angle in order to maintain its course. Ships with a small draught might have more risk in maneuvering to its point of view compared with a ship with a larger draught. This paper discusses maneuverability of a ship with a small draught in steady wind. The effect of wind on ship speed, drift angle, and rudder angle are investigated in a steady state condition. Five different ratios of wind velocity to ship speed from 1.0 …

Discrete Power Control In Heterogenous Networks, Yuanyuan Wang, Wibowo Hardjawana, Branka Vucetic

Makara Journal of Technology

In heterogeneous networks (HetNets) where femtocell base stations (FBSs) are deployed within the radio coverage of macrocell base stations (MBSs) to increase network capacity, co-channel interference limits overall system performance with universal frequency reuse. This paper investigates new distributed downlink discrete power control scheme for FBSs in HetNets with FBSs cooperation. The objective of the proposed power control scheme is to maximize the number of simultaneous FBSs transmissions in a single transmission wireless channel where each FBS is allowed to transmit only if the signal-to-interference-noise ratio (SINR) requirements for both FBSs and MBS users are satisfied. We apply a stochastic …

Multi-Project Scheduling Cost Optimization In A Machine Manufacturer Engineer-To-Order, Farizal Farizal, Amar Rachman, Tifani Tandean, Sumarsono Sudarto, Katsuhiko Takahashi

Makara Journal of Technology

This paper discusses the utilization of mixed integer linear programming (MILP) model to optimize cost for multiproject scheduling in a machine maker company. The objective is to minimize total project’s penalty cost and labor cost. The model formulated shows how to achieve the objective i.e. whether to use outsourcing or overtime to finish all projects. The model of multi-project scheduling was solved by Branch & Bound algorithm coded in Lingo 14.0 software. The case study shows that if a company wants to minimize lateness, it should use overtime instead of outsourcing, which minimize total lateness of projects by 144 days …

Analysis Of Arm Movement Prediction By Using The Electroencephalography Signal, Reza Darmakusuma, Ary Setijadi Prihatmanto, Adi Indrayanto, Tati Latifah Mengko, Lidwina Ayu Andarini, Achmad Furqon Idrus

Makara Journal of Technology

Various technological approaches have been developed in order to help those people who are unfortunate enough to be afflicted with different types of paralysis which limit them in performing their daily life activities independently. One of the proposed technologies is the Brain-Computer Interface (BCI). The BCI system uses electroencephalography (EEG) which is generated by the subject’s mental activity as input, and converts it into commands. Some previous experiments have shown the capability of the BCI system to predict the movement intention before the actual movement is onset. Thus research has predicted the movement by discriminating between data in the “rest” …