Mechanical Engineering Commons^™

Fundamental Study Of Nonlinear Electrophoresis, Joseph Armakan Bentor

All Dissertations

Classical electrophoretic theory describes the linear response of particles suspended in Newtonian fluids under weak electric fields. When the electric field exceeds this weak limit, a nonlinear response arises due to non-uniform surface conduction over the curved particles. This nonlinear behavior introduces dependencies on fluid and particle properties not considered in the classical theory, offering potential advantages for microfluidic particle manipulation. While this phenomenon has been extensively studied theoretically and numerically in Newtonian fluids, experimental investigations have been relatively limited.

Fluid rheology can significantly alter particle dynamics under applied electric fields. Rheological properties like shear-thinning and elasticity which are not …

Experimental Study On The Effect Of Micro Concentrations Of Hybrid Nanofluids Through Microchannel Heat Sinks, Mohamed Salaheldin Elsherbiny, Moustafa Ali, Moatsem Shahin, Mahmoud El-Kady

Renewable Mechanical Energy

The current study examines the convective heat transfer coefficient experimentally. It assesses the performance of Al2O3, CuO, ZnO, and Ag/ distilled water nanofluids up to a tetra level of hybridization utilized in microprocessor cooling systems equipped with MCHS. An equal ratio of 50%, 33.3%, and 25% for di-, tri-, and tetra-nanofluids, respectively, with a focus on micro-volume fraction 0.025% and comparing it with 0.05%. Operating conditions were as follows: heat loading from 136.4 up to 196.4 watts; and flow rate from 0.35 up to 0.5 LPM. The findings showed that all types of mono nanofluids showed an increase in Nu …

Activity: Students Find Conceptual Errors In Ai Output, Janie Brennan

Generative AI Teaching Activities

Instructor asks ChatGPT questions related to a key concept to find one where ChatGPT has conceptual errors. Ask students to find the errors and explain them.

Investigating The Feasibility And Mechanisms Of Cold Spray Deposition Of Polymer-Based Powders On Fiber-Reinforced Composite Substrates, Nicholas Beau Mennie

Theses and Dissertations

Fiber-reinforced composites have become important structural components in industries such as aerospace and energy due to their high mechanical strength and relatively light structural weight. However, during operation, these materials can be prone to impact damage and disintegration. Effective protection via metalization and repair of composites would, therefore, reduce the cost and time for replacement parts. Polymer-based cold spray, while a relatively new technique, can be utilized to metalize and possibly repair composite materials subjected to impact-induced damage. In this work, studies involving polymers and composite cold spray were performed to enable the process of safeguarding, enhancing, or repairing various …

Interaction Of Particles With Plasma And Shock Produced By Pulsed Spark Discharge, Shomik Mukhopadhyay

Dissertations

Interactions of powders with high-temperature plasma and shockwaves occur in diverse scenarios, such as nuclear blasts, accidental industrial dust explosions, solid propellant combustion in explosive charges and when removing contaminants from surfaces. Electrostatic Discharge (ESD), known for generating shock and plasma, is a promising lab-scale technique for simulating these interactions. Studies with ESD involved placing powders near a spark-producing gap between electrodes and observing mechanical and chemical processes like particle motion and ignition. A limited range of spark conditions and material properties have been tested, which facilitated the development and validation of preliminary computational models describing this system. Significant gaps …

Analysis Of The Effect Of Different Surface Preparation Methods On Corrosion Resistance And Adhesion Strength Of Astm A36 Steel Substrate With Surface Tolerant Epoxy Paint As Coating Material, Irwan Wijaya Santoso, Daffa Aqila, Rini Riastuti, Rizal Tresna Ramadhani

Journal of Materials Exploration and Findings

In the industrial world, to extend the service life of materials, protection methods are carried out to slow down the material's corrosion rate. The protection method that is often used is the coating method. The coating method is a protection method by coating the substrate material using a coating material to prevent contact between the substrate material and the environment. In this research, the substrate material used is ASTM A36 steel and the coating material used is Surface Tolerant Epoxy paint. The independent variable used in this study lies in the surface preparation method which consists of: solvent cleaning, hand …

Synthesis Of Durable Zeolite 13x Insertion Coatings And Scaled-Up Experimental Demonstration For Co2 Capture, Daniel Jamil Hocheimy

Theses and Dissertations

Minimizing the energy requirement for capturing carbon dioxide (CO₂) from post-combustion sources is critical to efficient industrial decarbonization and subsequent mitigation of the effects of climate change. The current portfolio of CO₂ capture technologies includes absorption, membrane separation and packed bed adsorption, which suffer from high energy and temperature requirements, scalability, and location dependency issues. Adsorption-based systems could cater to these concerns; however, their current embodiments primarily use packed adsorbent bed design and electricity-driven vacuum pumps to regenerate them. While simple and easy to fabricate, these designs are not scalable and cannot use heat to regenerate them …

Assessment Of Risk Factors Related To Body Pain Complaints In Tanzania Construction Industry, Fatma K. Mohamed

Tanzania Journal of Engineering and Technology (TJET)

The construction industry is associated with risks that can result in musculoskeletal diseases. Although young male workers who are presumed to be healthy dominate the industry in Tanzania, body pain complaints have been widely reported. The aim of this study is to assess the prevalence and causes of body pains in workers. A cross-sectional study involving 396 workers was conducted. A chi square test was used for testing association of independent categorical variables and binary logistic regression analysis was used to determine predictors for body pain complaints. The results show that all study participants complained of at least one form …

Research On 3d Printing Resin Exposure Properties And Its Application On Centrifugal Microfluidic Platform Based On Fluorescence Detection, Zheng Qiao

LSU Doctoral Dissertations

This dissertation encapsulates significant advancements in the field of SLA 3D printing and centrifugal microfluidics. Central to the research is the development of a novel mathematical model for predicting trapped resin thickness in SLA 3D printing, a groundbreaking contribution that addresses a critical aspect of printing intricate structures. This model, the first to establish a mathematical relationship for resin thickness, is rooted in a comprehensive study of the resin curing process. The research leverages the concept of 'critical dosage' for resin curing, leading to a more refined and theoretically grounded approach for calculating curing thickness. Experimentation further validates the model, …

Globular Protein For Surface Modification Of Cellulosecontaining Materials, Nodira Saydaliyeva

Technical science and innovation

The purpose of this work is the chemical modification of cotton fabrics with natural globular protein. Modification was carried out in the process of finishing cotton fabrics, after decoction and bleaching in a continuous mode. The effect of modification on the strength, protein content and functional groups of cotton fabric has been studied. According to the results obtained using the AUTOGRAPH AGS-N machine, it was found that the modification of cotton fabrics with a solution of globular protein increases the strength of the treated fabrics, depending on the concentration of the modifier and the temperature regime. Treatment with a highly …

Dying Of Natural Silk Deglued By Various Methods, Venera Djavdatovna Khamidova

Technical science and innovation

Products made of natural silk are indispensable for their hygienic properties and will always be in great demand. To obtain an even and intense coloration on a textile material, it is necessary to ensure its effective preparation with the most complete removal of hydrophobic contaminants (both natural and silicone oils applied during the weaving process, lubricants, etc.), which hinder the dyeing of the substrate and reduce the color characteristics of the obtained colors. Therefore, the issue of preparing natural silk for dyeing is relevant. In view of the sensitivity of the main fiber-forming component of natural silk - fibroin to …

Thermo-Elasto-Plastic Stability Of Biaxially Loaded Hollow Rectangular Section Steel Beam-Columns With Applied Torsion, George Adomako Kumi

Civil & Environmental Engineering Theses & Dissertations

Presented herein is an experimental and theoretical study of biaxially loaded hollow rectangular section steel beam-columns with applied torsion at elevated temperatures. The theoretical analysis is based on a system of simultaneous materially nonlinear differential equations of equilibrium for which an iterative semi-analytic solution approach is formulated. Although the primary goal of this research is to study the influence of elevated temperatures on the steel member with the complex loading, rigorous analysis is also conducted of the member at ambient temperature for comparison. The experimental part of the study involves conducting tests on the members at both ambient and high …

Benchmarking Of A Sco2 Heat Exchanger Flow Loop, David Velasco

Doctoral Dissertations and Master's Theses

Heat transfer of supercritical carbon dioxide (sCO2) was studied experimentally by commissioning a sCO2 flow loop featuring a horizontal tube-in-tube counterflow heat exchanger with a circular cross section. The main objective was to establish experimental heat transfer research capabilities for sCO2 at Embry-Riddle Aeronautical University’s (ERAU) Thermal Science Lab. sCO2 experiences a drastic change in thermophysical properties near its critical point that results in unique heat transfer characteristics. The high pressures at which sCO2 exists make the large gradients in thermophysical and transport properties difficult to study, experimentally and numerically. However, understanding the heat transfer characteristics and thermophysical behavior of …

Cfd Study On Two-Phase Flow Patterns In A Pipe With 90º Elbow In Different Operating Conditions, Hagar Alm-Eldin Bastawissi, Mohammed Ahmed Khafagy, E. A. El Shenawy Prof. Dr., Ahmed M. Salem Dr

Journal of Engineering Research

Recently, CFD has offered a technological solution for modelling multi-phase flow in which we can make endless simulations with reduced expenses and effort in high accuracy results; we shall also mention that experimental studies have limitations for safety considerations when experimenting with flow in high temperature or pressure values or medium nature as in nuclear or chemical flows.In this paper, we used the ANSYS FLUENT CFD program to simulate the two-phase flow in a pipe to study the effect of attaching a 90-degree elbow fitting to the piping system, seeking to find out the change in the pattern and resulting …

Cost Estimation Proxy Models For Economic Evaluations In Petroleum Projects: A Case Study From The Onshore Gas Field In The Southern Coastal Tanzania Basin, Fulmence Kaborogo

Tanzania Journal of Engineering and Technology (TJET)

Petroleum economic evaluation involves estimating revenues from forecasted production profiles and field costs including capital expenditures (CAPEX), drilling expenses (DRILLEX), and operating expenses (OPEX). The existing cost-estimating tool requires several inputs making it time-intensive and difficult to use with few data during the early stages of projects. Majority of the previously developed time saving cost estimations proxy models rely on unrealistic assumptions that include uniform operational costs for different fields with a different number of wells, casings, and drilled depths. This work focused at developing proxy models that consider the variability of the development costs with different parameters. The developed …

Steminism: Analyzing Factors That Improve Retention Of Women In Stem, Kira Carter, Jane Kelley, Jason Vasser-Elong, Rc Patterson

Dissertations

Our co-authored research ‘Steminism: Analyzing Factors That Improve Retention for Women as STEM Majors’ analyzed factors that contributed to the retention of women in science, technology, engineering, and mathematics (STEM) programs at Missouri University of Science & Technology (Missouri S&T). Women make up half of the US population, and while careers in (STEM) are an integral part of the US economy, women are underrepresented in these career fields. The purpose of our dissertation is to address the underrepresentation of women in STEM majors. Our methodology included homogeneous sampling to collect qualitative data. More specifically, we consulted with academic advisors and …

Process Simulation For Converting Co2 Emissions From The Cementindustry To Dimethyl Ether, Nour Abou Seada, Dina Aboelela

Biochemical Engineering

Climate change is the leading severe problem in the twenty-first century, which is associated with greenhouse gas emissions,carbon dioxide that is the foremost cause of global warming and super greenhouse effect. In this concern, to avoid hazardousproblems, the steady stream of CO2 effluents existing in the atmosphere must be transformed to beneficial products for beingused as an abundant chemical feedstock. Implementing a new green strategy, which is known for the catalytic hydrogenationof CO2 into alternative fuels and valuable chemicals, will be a long-lasting solution to alleviate CO2 emissions. In this paper,a process simulation showing the synthesis of dimethyl ether (DME) …

Hydrogen Production From Microbial Electrolysis Cells Powered With Microbial Fuel Cells, Dina Aboelela

Biochemical Engineering

No abstract provided.

A Review Of Dielectric Barrier Discharge Cold Atmospheric Plasma For Surface Sterilization And Decontamination, Kolawole Adesina, Ta Chun Lin, Yue-Wern Huang, Marek Locmelis, Daoru Frank Han

Biological Sciences Faculty Research & Creative Works

Numerous investigations have shown that non-equilibrium discharges at atmospheric pressure, also known as "cold atmospheric plasma" (CAP) are efficient to remove biological contaminants from surfaces of a variety of materials. Recently, CAP has quickly advanced as a technique for microbial cleaning, wound healing, and cancer therapy due to the chemical and biologically active radicals it produces, known collectively as reactive oxygen and nitrogen species (RONS). This article reviews studies pertaining to one of the atmospheric plasma sources known as Dielectric Barrier Discharge (DBD) which has been widely used to treat materials with microbes for sterilization, disinfection, and decontamination purposes. To …

Strategies To Mitigate Efflorescence In Walls Constructed Using Clays Bricks; A Review Article, Marwa Abdulkareem. Anber, Soran Abdulrahman Ahmad, Naros Rahman Mahmoud, Kawan Fuoad. Kayani, Mohammed Ali Abdulrehman

Al-Esraa University College Journal for Engineering Sciences

_{The construction of buildings, especially residential housing for communities, is a significant industry on a global scale. Masonry units such as bricks, blocks, and stones are often utilized materials. Bricks are highly regarded because to their widespread availability, cost-effectiveness, and excellent insulating capabilities. Nevertheless, the presence of efflorescence presents a difficulty in the construction of brick walls. Efflorescence refers to the process in which salts move to the outer layer of the brick, resulting in the formation of white deposits and negatively impacting its visual appeal. Efflorescence is caused by various circumstances, such as the existence of salts in bricks, …}

The Importance Of Cryptography In Cloud Computing, Saja Alaam Talib

Al-Esraa University College Journal for Engineering Sciences

Cloud computing has grown as a widely accepted concept simultaneously, as the alarms for the security of data and information. This paper seeks to establish the comprehensive roles of cryptography in tackling these issues in the Cloud environment. The study begins with the historical background of cryptography and then moves on to analyze trends in information technology before discussing on the challenges to security in cloud computing. The goal of its publication is to highlight the importance of using cryptographic technologies for the protection of information confidentiality, its integrity and compliance. The combination of literature review and the case study …

Carbon Dioxide Gasification Of Biochar: A Study On Utilizing Captured Co2 To Mitigate Greenhouse Gas Emission And Improving Carbon Conversion Efficiency, Nnamdi Ofuani

College of Graduate Studies: Theses & Dissertations

With rapidly growing global economies and world population, fossil fuel continues to play a major role in meeting current energy demands. Carbon capture and storage (CCS) technologies have, hence, been implemented to reduce CO₂ emissions in the atmosphere. With the implementation of CCS technologies comes the need to utilize the captured CO₂. This research, therefore, proposes CO₂ gasification of biochar as a viable carbon utilization pathway. With captured CO₂ coming at various concentrations, there is a need to understand how CO₂ concentration affects biochar conversion to useful products. This study, therefore, evaluates the effects …

A Concept Of Producing Aluminum In-Situ On The Moon Through Molten Salt Electrolysis, Jacob N. Ortega, Jeffrey Smith, Fateme Rezaei, David Bayless, William Schonberg, Daniel Stutts, Daoru Han

Materials Science and Engineering Faculty Research & Creative Works

This paper presents a concept of producing aluminum in-situ on the lunar surface, namely, the Lunar In-Situ Aluminum Production through Molten Salt Electrolysis (LISAP-MSE) method developed at Missouri University of Science and Technology. This paper aims to demonstrate the use of electro-deoxidation to reduce aluminum oxide (i.e., alumina) into aluminum and oxygen gas via electrolysis in a molten salt bath for the production of aluminum on the Moon. It is shown that with a steady supply of hydrogen chloride, this in-situ resource utilization (ISRU) method could supply several necessary materials consumed in the electro-deoxidation process except hydrogen chloride to produce …

Magnetic Separation Of Lunar Regolith Simulants With Applications To In Situ Resource Utilization On The Moon, Peter Bachle, Jeffrey Smith, Fateme Rezaei, David Bayless, William Schonberg, Daoru Han

Chemical and Biochemical Engineering Faculty Research & Creative Works

The development of in situ resource utilization (ISRU) for metal extraction is imperative as a steppingstone for habitation construction in lunar and non-terrestrial environments. Separation of minerals by chemical composition is important to optimize metal and oxygen liberation from lunar ore. To this effect, devices capable of separating aluminum bearing minerals from iron-bearing minerals from the lunar regolith simulants have been developed. Twenty-eight different simulants have been used in this study. A dual-belt separator was designed to reduce middling. Para-magnetic minerals were reliably separated using a neodymium N52-magnet-separator system. Effective separation of aluminum-bearing minerals from iron-bearing minerals was greater than …

Electrostatic Sorting Of Lunar Regolith Simulants For Sustainable Resource Utilization: Modeling And Characterization Of Particle Size Distribution, Abdullah Al Moinee, Peter Bachle, Kyle Newport, William Schonberg, David Bayless, Jeffrey Smith, Daoru Han, Fateme Rezaei

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In pursuit of sustainable resource utilization on the Moon, this paper delves into modeling and characterization of particle size distribution (PSD) of lunar regolith simulants in an electrostatic system. A prototype electrostatic sieve was built and tested with four sample simulants mirroring properties of lunar mare and highland regolith. An alternating four-phase (90 degrees, 180 degrees, 270 degrees, 360 degrees) traveling square-wave was utilized for particle-directed transport to model the diverse trajectories of the particles. Numerically, we scrutinized how the distribution functions of the particles are manifested as the electrostatic field propagates, with a focus on three distinct particle ranges …

Enhancement Of The Performance And Emission Attributes For The Diesel Engine Using Diesel-Waste Cooking Oil Biodiesel And Graphene Oxide Nanofluid Blends Through Response Surface Methodology, Medhat Elkelawy Prof. Dr. Eng., E A El Shenawy, Hagar Alm-Eldin Bastawissi, Mahmoud M. Shams

Mansoura Engineering Journal

This study examined how diesel fuel and waste-cooked oil (WCO) biodiesel blends added by various concentrations of graphene oxide (GO) nanoparticles can effect on the performance and emission characteristics of constant-speed, four-stroke, single-cylinder, water-cooled diesel engines. The GO nanoparticles concentrations are 50,100 and 150 ppm dispersed in different diesel-WCO biodiesel blends are pure diesel fuel (B0), 20% WCO biodiesel and 76% diesel fuel (B20), and 40% WCO biodiesel and 56% diesel fuel (B40). In addition 4% toluene in all blends which used as a surfactant. The diesel engine fueled with these blends and operated at various engine loads are 2, …

Kinetic Modeling Of Electrostatic Sieving For Lunar Regolith Beneficiation: Case Studies, Easton Ingram, Emmanuela Amen Eze, Jeffrey Smith, Fateme Rezaei, David Bayless, William Schonberg, Daoru Han

Materials Science and Engineering Faculty Research & Creative Works

A new kinetic particle modeling framework was developed to investigate electrostatic transport of lunar regolith particles with applications to the concept of electrostatic sieving. the new approach is based on kinetic particle dynamics and includes major modules of sampling the particle size distribution, solving electric fields, and tracking motion of charged dust grains. Case studies for a concept of electrostatic sieving were chosen to validate the new model. the simulation achieved similar yields reported in previous works, which served as validation of the model. the new model is computationally efficient and could serve as a design, analysis, and optimization tool.

Progress Of Lisap-Mse: A Concept Of Producing Aluminum In-Situ On The Moon Through Molten Salt Electrolysis, Jacob N. Ortega, David Bayless, Daniel Stutts, Daoru Han, Todd P. Sander, Jeffrey Smith, Fateme Rezaei, William Schonberg

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper presents a concept of producing aluminum in-situ on the lunar surface, namely, the Lunar In-Situ Aluminum Production through Molten Salt Electrolysis (LISAP-MSE) method developed at Missouri University of Science and Technology. This paper aims to demonstrate the use of electro-deoxidation to reduce aluminum oxide (i.e., alumina) into aluminum and oxygen gas via electrolysis in a molten salt bath for the production of aluminum on the Moon. It is shown that with a steady supply of hydrogen chloride, this in-situ resource utilization (ISRU) method could supply several necessary materials consumed in the electro-deoxidation process except hydrogen chloride to produce …

Electrostatic Sorting Of Lunar Regolith Simulants For Sustainable Resource Utilization: Modeling And Characterization Of Particle Size Distribution, Abdullah Al Moinee, Peter Bachle, Kyle Newport, William Schonberg, David Bayless, Jeffrey Smith, Daoru Han, Fateme Rezaei

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In pursuit of sustainable resource utilization on the Moon, this paper delves into modeling and characterization of particle size distribution (PSD) of lunar regolith simulants in an electrostatic system. a prototype electrostatic sieve was built and tested with four sample simulants mirroring properties of lunar mare and highland regolith. an alternating four-phase (90 degrees, 180 degrees, 270 degrees, 360 degrees) traveling square-wave was utilized for particle-directed transport to model the diverse trajectories of the particles. Numerically, we scrutinized how the distribution functions of the particles are manifested as the electrostatic field propagates, with a focus on three distinct particle ranges …

Investigation Of Space Charge Effects On Co2 Electrocatalytic Reduction On Gd-Doped Ceria Via Scanning Kelvin Probe And Model-Based Bayesian Analysis, Alejandro Mejia

Graduate Theses, Dissertations, and Problem Reports (ETD)

In studying novel energy conversion and storage systems, such as high-temperature electrolysis, numerous underlying fundamental physical processes remain unclear or inadequately understood. Among these, the modeling and comprehension of surface reaction mechanisms, coupled with the intricate effects of space‑charge interfaces, remains an unclear and challenging area of research.

The work of this dissertation involves the development of a 2D finite element analysis model, leveraging the robust MOOSE framework from INL. This model, featuring inhomogeneous defect thermodynamics for near-surface chemistry, formulated through Poisson‑Cahn variational theory, has been exploited for studying the electrocatalytic reduction of CO₂ on gadolinia doped ceria. The …