Mechanical Engineering Commons^™

Additive Manufacturing Of Continuous Carbon Fiber-Reinforced Sic Ceramic Composite With Multiple Fiber Bundles By An Extrusion-Based Technique, Ruoyu Chen, Adam Bratten, Joshua Rittenhouse, Ming-Chuan Leu, Haiming Wen

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Due to the high cost, complex preparation process and difficulty in structural design, the traditional methods for carbon fiber reinforced SiC ceramic composite preparation have great limitations. This paper presents a technique for the additive manufacturing multiple continuous carbon fiber bundle-reinforced SiC ceramic composite with core-shell structure using an extrusion-based technique. A conventional nozzle system was modified to print simultaneously a water based SiC paste with continuous carbon fibers. Different levels of binder contents were investigated to optimize the stickiness, viscosity, thixotropy and viscoelasticity of the paste. After sintering, SiC whiskers were generated on the surface of fiber, which is …

Two-Level Targeter Convergence Study For Collinear Libration Point Spacecraft Formations, Donna Jennings, Henry J. Pernicka

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Spacecraft formation flying has attracted an increasing amount attention over the past several decades including a growing interest in relative motion at the collinear lib ration points. This current work builds on previous efforts by further developing and characterizing a two-level targeting (TLT) algorithm used to determine relative motion at lib ration points by performing a convergence study. A parametric study was conducted to identify the sensitivity of the algorithm to a variety of inputs and constraints. The parametric study revealed that the two-level targeting algorithm convergence properties significantly improve when using a higher order initialization estimate. The size of …

Direct Numerical Simulation Of Acoustic Disturbances In A Hypersonic Two-Dimensional Nozzle Configuration, Nathaniel Hildebrand, Meelan M. Choudhari, Cole P. Deegan, Junji Huang, Lian Duan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Direct numerical simulations (DNS) are performed to study acoustic radiation in a quasi-two-dimensional nozzle with two independents spatially evolving turbulent boundary layers with an edge Mach number of 6. The emphasis of this work is to compare the radiated pressure fluctuations in a geometrically confined environment with those radiated from a single wall in an unconfined setting. The boundary-layer profile of the rms pressure fluctuation scaled by the mean shear stress at the wall is found to be in good agreement with prior flat-plate calculations at similar conditions. However, the normalized rms pressure fluctuation within the freestream p region is …

3d-Printed Gelatin-Alginate Hydrogel Dressings For Burn Wound Healing: A Comprehensive Study, Fateme Fayyazbakhsh, Michael J. Khayat, Ming-Chuan Leu

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Burn Wound Treatment is Still a Clinical Challenge Due to the Severity of Tissue Damage and Dehydration. among Various Wound Dressings, Hydrogel Materials Have Gained Significant Attention for Burn Wound Treatment in Clinical Practice Due to their Soothing and Moisturizing Activity. in This Study, 3D-Printed Dressings Were Fabricated using Clinically Relevant Hydrogels for Deep Partial-Thickness Burn (PTB) Wounds. Different Ratios of Gelatin and Alginate Mixture Were 3D-Printed and Examined in Terms of Rheological Behavior, Shear Thinning Behavior, Mechanical Properties, Degradation Rate, and Hydration Activity to Tune the Hydrogel Composition for Best Functionality. the Cell-Laden Dressings Were Bioprinted to Evaluate the …

Design, Development, And Testing Of Near-Optimal Satellite Attitude Control Strategies, Giovanni Lavezzi

Electronic Theses and Dissertations

Advances in space technology and interest toward remote sensing mission have grown in the recent years, requiring the attitude control subsystems of observation satellites to increase their performances in terms of pointing accuracy and on-board implementability. Moreover, an increased interest in small satellite missions and the recent technological developments related to the CubeSats standard have drastically reduced the cost of producing and flying a satellite mission. In this context, the proposed research aims to improve the state of the art for satellite attitude control methodologies by proposing a near-optimal attitude control strategy, simulated in a high-fidelity environment. Two strategies are …

Spatial Transformation Of A Layer-To-Layer Control Model For Selective Laser Melting, Xin Wang, Robert G. Landers, Douglas A. Bristow

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Selective Laser Melting (SLM) is an Additive Manufacturing (AM) technique with challenges in its complexity of process parameters and lack of control schemes. Traditionally, people tried time-domain or frequency-domain control methods, but the complexity of the process goes beyond these methods. In this paper, a novel spatial transformation of SLM models is proposed, which transforms the time-domain process into a spatial domain model and, thus, allows for state-space layer-to-layer control methods. In a space domain, this also provides the convenience of modelling laser path changes. Finally, a layer-to-layer Iterative Learning Control (ILC) method is designed and demonstrates the methodology of …

High-Pressure Kinetic Interactions Between Co And H2 During Syngas Catalytic Combustion On Pdo, Ran Sui, John Mantzaras, Rolf Bombach, Meysam Khatoonabadi

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The catalytic combustion of H2/CO/O2/N2 mixtures over PdO was investigated at pressures 3 to 10 bar, H2:CO volumetric ratios 1:5 to 3:1, and global equivalence ratios ψ = 0.13 and 0.23. The catalyst surface temperatures were controlled to 540-690 K, a range especially important for hybrid hetero-/homogeneous combustion approaches with large gas turbines at idle or part-load operation and for microreactors with recuperative small-scale turbines. In situ Raman measurements determined the major gas-phase species concentrations over the catalyst boundary layers in a channel-flow reactor, thermocouples monitored the surface temperatures, and surface characterization identified the catalyst oxidation state (PdO) and surface …

Microscale Transverse Compression Modeling: A Comparative Study Of The Analytical Mac/Gmc Methods To Experimental Results, Emily Zeitunian

Dissertations, Master's Theses and Master's Reports

Composite materials require a multi-scale approach to fully understand its behavior. At the micro level, material behavior analysis is conducted most often using numerical or analytical approaches. These models, however, require validation from experimental data to ensure material predictions are accurate. This study compares a semi-analytical micromechanical analysis tool, MAC/GMC, to experimental results of in-situ microscale transverse compression testing conducted at AFRL facilities. Effective properties, stress-strain curves, stress and strain fields, and damage predictions are compared with experimental outputs. Both generalized method of cells (GMC) and high-fidelity generalized method of cells (HFGMC) theories implemented within MAC/GMC show results that agree …

Juggling A Devil-Stick: Hybrid Orbit Stabilization Using The Impulse Controlled Poincaré Map, Nilay Kant, Ranjan Mukherjee

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The control design for juggling a devil-stick between two symmetric configurations is proposed. Impulsive forces are applied to the devil-stick at the two configurations; and impulse of the force and its point of application are modeled as the control inputs. The dynamics of the devil-stick is described by a single return Poincaré map, and it is shown that the control objective of juggling can be achieved by stabilizing a hybrid orbit. The impulse controlled Poincaré map (ICPM) approach, recently proposed for stabilization of continuous-time orbits of underactuated systems, is extended to achieve asymptotic stabilization of the hybrid orbit. The applicability …

Investigating Ground Interactions Of A Rotocraft Landing Vehicle On Titan, Adam Rozman

Honors Undergraduate Theses

The exploration of celestial bodies has recently advanced from rovers to rotorcraft. This includes the recent flights of Mars Ingenuity and the upcoming Dragonfly mission to explore the terrain of Saturn’s moon Titan as part of NASA’s New Frontiers Program. Flight-based landers can travel quickly to sites kilometers apart and land in complex terrain. Although cruise conditions for these rotorcrafts are well understood, studies are necessary to understand take-off and landing. In ground effect conditions, a rotor wake impinges and reflects off the ground, creating changes in aerodynamics such as increased lift. Additionally, operating over loose surfaces, the rotors can …

Autoignition Delay Time Measurements And Chemical Kinetic Modeling Of Hydrogen/Ammonia/Natural Gas Mixtures, Jessica Baker

Electronic Theses and Dissertations, 2020-2023

In recent years, hydrogen-carrying compounds have accrued interest as an alternative to traditional fossil fuels due to their function as zero-emission fuels. As such, there is interest in investigating hydrogen-carrying compounds to improve understanding of the fuels' characteristics for use in high pressure systems. In the current study, the oxidation of ammonia/natural gas/hydrogen mixtures was carried out to study CO formation profiles as well as the ignition delay times behind reflected shock waves in order to refine chemical kinetic models. Experiments were carried out in the University of Central Florida's shock tube facility by utilizing chemiluminescence to obtain OH* emission …

A Decoupled Engineering Methodology For Accurate Prediction Of Ablative Surface Boundary Conditions In Thermal Protection Systems, Justin Cooper

Theses and Dissertations--Mechanical and Aerospace Engineering

The main objective of the present work is to demonstrate a method for prediction of aerothermal environments in the engineering design of hypersonic vehicles as an alternative to the current heritage method. Flat plate and stagnation point boundary layer theory require multiple assumptions to establish the current engineering paradigm. Chief among these assumptions is the similarity between mass and heat transfer. Origins of these assumptions are demonstrated and their relationship to conservative engineering design is analyzed, as well as conditions where they possibly break down. An alternative approach for assessing aerothermal environments from the fluid domain is presented, which permits …

Formation Control With Bounded Controls And Collision Avoidance: Theory And Application To Quadrotor Unmanned Air Vehicles, Zachary S. Lippay

Theses and Dissertations--Mechanical and Aerospace Engineering

This dissertation presents new results on multi-agent formation control and applies the new control algorithms to quadrotor unmanned air vehicles. First, this dissertation presents a formation control algorithm for double-integrator agents, where the formation is time varying and the agents’ controls satisfy a priori bounds (e.g., the controls accommodate actuator saturation). The main analytic results provide sufficient conditions such that all agents converge to the desired time-varying relative positions with one another and the leader, and have a priori bounded controls (if applicable). We also present results from rotorcraft experiments that demonstrate the algorithm with time-varying formations and bounded controls. …

Numerical And Scaling Study On Application Of Inkjet Technology To Automotive Coating, Masoud Arabghahestani Dr.

Theses and Dissertations--Mechanical and Aerospace Engineering

A thorough literature review identified lack of precision control over quality of droplets generated by the currently available industrial sprayers and a growing need for higher quality droplets in the coating industry. Particularly, lack of knowledge and understanding in continuous inkjets (CIJ) and drop-on-demand (DOD) technologies is identified as significant. Motivated by these needs, this dissertation is dedicated to computational fluid dynamics (CFD) and scaling studies to improve existing inkjet technologies and develop new designs of efficient coating with single and/or multiple piezoelectric sensors to produce on-demand droplets. This dissertation study aims at developing a new DOD type coating technology, …

In-Situ Characterization Of Burr Formation In Finish Machining Of Inconel 718, Hamzah M. Zannoun

Theses and Dissertations--Mechanical and Aerospace Engineering

One of the undesirable byproducts that occur during the machining process is the development of burrs, which are defined as rough excess material that forms around the geometric discontinuities of a part. Burrs are especially problematic because they have negative impacts across the triple bottom line: economic, environmental, societal. For one, they are expensive to remove because the deburring process is entirely manual and requires skill. Further, burr material is typically discarded which is adding to the already mounting waste generated from machining such as in coolant and chip disposal. Lastly, there are many societal implications, such as operator injury …

Formation Control With Collision Avoidance For Fixed-Wing Unmanned Air Vehicles With Speed Constraints, Christopher Heintz

Theses and Dissertations--Mechanical and Aerospace Engineering

Advances in the miniaturization of powerful electronic components and motors, the democratization of global navigation satellite systems (GNSS), and improvements in the performance, safety, and cost in lithium batteries has led to the proliferation of small and relatively inexpensive unmanned aerial vehicles (UAVs). Many of these UAVs are of the multi-rotor design, however, fixed-wing designs are often more efficient than rotary-wing aircraft, leading to a reduction in the power required for a UAV of a given mass to stay airborne. Autonomous cooperation between multiple UAVs would enable them to complete objectives that would be difficult or impossible for a single …

Guiding A Human Follower With Interaction Forces: Implications On Physical Human-Robot Interaction, George L. Holmes, Keyri Moreno Bonnett, Amy Costa, Devin Michael Burns, Yun Seong Song

Psychological Science Faculty Research & Creative Works

This work challenges the common assumption in physical human-robot interaction (pHRI) that the movement intention of a human user can be simply modeled with dynamic equations relating forces to movements, regardless of the user. Studies in physical human-human interaction (pHHI) suggest that interaction forces carry sophisticated information that reveals motor skills and roles in the partnership and even promotes adaptation and motor learning. In this view, simple force-displacement equations often used in pHRI studies may not be sufficient. To test this, this work measured and analyzed the interaction forces (F) between two humans as the leader guided the blindfolded follower …

Neural Network Attitude Control System Design For The Wallops Arc-Second Pointer, Pavel Galchenko, Henry J. Pernicka

Mechanical and Aerospace Engineering Faculty Research & Creative Works

No abstract provided.

Wireless Power Transfer In Autonomous Mobile Microgrids, Carl Greene

Dissertations, Master's Theses and Master's Reports

The ability to autonomously dock unmanned ground vehicles plays a key role in mobile micro-grids, where efficient power transfer is paramount. The approach utilized in this work allows for near-field wireless power transfer in remote locations with minimal support. Establishing a micro-grid power system connection autonomously using wireless power eliminates the arduous task of designing a complex, multiple degrees of freedom (MDOF) robotic arm. The work presented in this thesis focuses on both the hardware and software within the micro-grid system. This particular near-field wireless system consists of a primary and secondary set of modules, comprised of Litz wire coils, …

Editorial For The Special Issue On Micromachines For Non-Newtonian Microfluidics, Lanju Mei, Shizhi Qian

Mechanical & Aerospace Engineering Faculty Publications

In lieu of an abstract, this is an excerpt from the first page.

Microfluidics has seen a remarkable growth over the past few decades, with its extensive applications in engineering, medicine, biology, chemistry, etc [...]

Satellite Drag Coefficient Modeling For Thermosphere Science And Mission Operations, Piyush M. Mehta, Smriti N. Paul, Nicholas H. Crisp, Philip L. Sheridan, Christian Siemes, Günther March, Sean Bruinsma

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Satellite drag modeling remains the largest source of uncertainty affecting space operations in low Earth orbit. The uncertainty stems from inaccurate models for mass density and drag coefficient. Drag coefficient modeling also impacts scientific knowledge on the physics and dynamics of the upper atmosphere through the estimation of high-fidelity mass density from measurements of acceleration on-board satellites. Efforts over the last decade have pushed drag coefficient modeling in the right direction, however, have resulted in multiple methods and tools. We provide a comprehensive review of the drag coefficient modeling methods and tools. Current scale differences between thermospheric data sets mostly …

Effects Of Wheel Rotation On Long-Period Wake Dynamics Of The Drivaer Fastback Model, Matthew Aultman, Rodrigo Auza-Gutierrez, Kevin Disotell, Lian Duan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Lattice Boltzmann method (LBM) simulations were performed to capture the long-period dynamics within the wake of a realistic DrivAer fastback model with stationary and rotating wheels. The simulations showed that the wake developed as a low-pressure torus regardless of whether the wheels were rotating. This torus shrank in size on the base in the case of rotating wheels, leading to a reduction in the low-pressure footprint on the base, and consequently a 7% decrease in the total vehicle drag in comparison to the stationary wheels case. Furthermore, the lateral vortex shedding experienced a long-period switching associated with the bi-stability in …

Concept Evaluation And Development Of A Novel Approach For Integration Of Turbogeneration, Electrification And Supercharging On Heavy Duty Engines, Satyum Joshi

Dissertations, Master's Theses and Master's Reports

While many technologies such as electrically assisted turbocharging, exhaust energy recovery and mild hybridization have already proven to significantly increase heavy-duty engine efficiency, the key challenge to their widespread adoption has been their cost effectiveness and packaging. This research specifically addresses these challenges through evaluation and development of a novel technology concept termed as the Integrated Turbogeneration, Electrification and Supercharging (ITES) system. The concept integrates a secondary compressor, a turbocompound/expander turbine and an electric motor through a planetary gearset into the engine cranktrain. The approach enables a reduced system cost and space-claim, while maximizing the efficiency benefits of independent technologies. …

Passive Intermodulation Under Different Spring Contact Conditions, Shengxuan Xia, Emmanuel Olugbade, Yuchu He, Yansheng Wang, Hanfeng Wang, Krishna Rao, Marco Poort, Haicheng Zhou, Warren Lee, Nicholas Mcdonnell, Jonghyun Park, Chulsoon Hwang

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Modularized designs have been widely used in today's consumer electronic devices and flexible RF springs are used for electrical connections between the modules. In the meantime, aluminum alloy material becomes a common chassis option. It is well known that the oxidized chassis surface introduces a certain level of nonlinearity when contacted by the springs, as known as passive intermodulation (PIM). PIM is one of the well-known root causes of the RF desensitization (desense). This paper is focused on investigating the relationship between PIM and contact conditions of the springs, especially contact area. The PIM level behavior is explained mathematically by …

Fuel-Rich Hetero-/Homogeneous Combustion Of C3h8/O2/N2 Mixtures Over Rhodium, John Mantzaras, Ran Sui, Rolf Bombach

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The catalytic (heterogeneous) and gas-phase (homogeneous) combustion of C3H8/O2/N2 mixtures over rhodium was investigated experimentally and numerically at 5 bar and at fuel-rich equivalence ratios π = 2.0-3.5 relevant to propane Catalytic Partial Oxidation (CPO). In situ spatially-resolved Raman measurements of major gas-phase species concentrations and Planar Laser Induced Fluorescence (PLIF) of formaldehyde were applied in an optically accessible channel-flow reactor to monitor the catalytic and gas-phase processes, respectively, while accompanying 2D simulations were carried out with detailed hetero-/homogeneous chemical reaction mechanisms. Due to the high gas-phase reactivity of propane, homogeneous chemistry could not be ignored over most of the …

Regulation Of Dendrite-Free Li Plating Via Lithiophilic Sites On Lithium-Alloy Surface, Yufang He, Mengyun Zhang, Aiping Wang, Bo Zhang, Hiep Pham, Qiao Hu, Li Sheng, Hong Xu, Li Wang, Jonghyun Park, Xiangming He

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Lithium (Li) deposition behavior plays an important role in dendrite formation and the subsequent performance of lithium metal batteries. This work reveals the impact of the lithiophilic sites of lithium-alloy on the Li plating process via the first-principles calculations. We find that the Li deposition mechanisms on the Li metal and Li22Sn5 surface are different due to the lithiophilic sites. We first propose that Li plating on the Li metal surface goes through the "adsorption-reduction-desorption-heterogeneous nucleation-cluster drop "process, while it undergoes the "adsorption-reduction-growth "process on the Li22Sn5 surface. The lower adsorption energy contributes to the easy adsorption of Li on …

Nanobubble Capillary Force Between Parallel Plates, Eric Bird, Zhi Liang

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The Aggregation of Fine or Ultrafine Particles in Liquid Due to the Nanobubble (NB) Bridging Capillary Force is a Key Process for Many Industrial Applications. the Magnitude and Direction of the NB Capillary Force (NBCF) Are Directly Affected by the Geometry of the NB Gas Bridge between Two Adjoining Particles. Although the NBCF Can Be Accurately Measured using Experimental Techniques, It is Very Challenging to Monitor the Images of a NB Capillary Bridge in Nanoscale Spatial Resolution in NBCF Measuring Experiments. as a Result, the Capillary Force Model that Predicts the Dependence of the NBCF on the Geometry of the …

Investigations Of The Low Temperature Combustion Regions And Emissions Characteristics Of Aerospace F24 In A Constant Volume Combustion Chamber And A Common Rail Direct Injection Ci Engine, Richard C. Smith Iii

College of Graduate Studies: Theses & Dissertations

A study was conducted to investigate the low temperature combustion (LTC) regions of aerospace F24 and ULSD in the static setting of a CVCC and the dynamic setting of a CRDI research engine. This research is conducted to reduce in-cylinder emissions by understanding and implementing a technique to achieve an extended LTC. Emissions data for this study were collected during the operation of the CRDI research engine with a MKS 2030 FTIR and an AVL Microsoot 483. The parameters researched within the static setting of the CVCC included the determinations of the cool flames and NTC regions within the LTHR …

A Non-Reacting Passive Scalar Comparison Of Starccm And Openfoam In A Supersonic Cavity Flame Holder, Thomas Nuese

Electronic Theses and Dissertations

The scramjet engine equipped with a modern-day airliner would allow for very quick travel across the United States. The major problem is that designing such an engine and testing it to make sure it is safe would cost millions if not billions of dollars. Computational fluid dynamics allows for complex designs to be tested but can still take many days, weeks, or even months to complete. With the use of computational fluid dynamics (CFD), the scramjet engine can be analyzed to determine a quicker way to test and develop a reliable configuration in addition to analyzing the effects of different …

Experimental Study Of Wall Bounded Harbor Seal Whisker Inspired Pin Geometries, Anish Prasad, Mark Ricklick

Publications

Conventional cylindrical/elliptical pins are one of the most widely used geometries in convection cooling systems and are used in the internal cooling of gas turbine blades and other applications, as they promote better heat transfer at the expense of large pressure losses and unsteadiness in the flow. The need to reduce pressure drop and maintain the heat transfer rates are a pressing requirement for a variety of industries to improve their cooling efficiency. One such prominent field of research is conducted in optimizing the design of pin geometries. In this study, a harbor seal whisker inspired geometry is being studied …