Mechanical Engineering Commons^™

Enhancing Crossflow Dynamics Through The Gas Injection From Multiple Cylinders, Sahrish B. Naqvi, Sadia Siddiqa, Maciej Matyka, Rama S. R. Gorla, Md. Mamum Molla

Faculty Publications

We investigate unsteady, two-dimensional laminar fluid flow around cylinders, focusing on understanding the impact of injecting methane gas through two diametrically opposite arcs on the cylinder in the crossflow of the second fluid. This study encompasses applications in mixing and dispersion, which are crucial in various technological and natural processes. Our analysis addresses velocity field’s contribution to the spatiotemporal distribution of transported quantities. We observed that mixing induces a transition from laminar to turbulent flow. Depending on the injected-to-crossflow velocity ratios, the wake vortices downstream of cylinder arrays separate from or connect to the injected gas. This phenomenon significantly impacts …

Heat Treatment Post-Processing For The Improved Mechanical Properties Of Scalmalloy® Processed Via Directed Energy Deposition, Rachel Boillat-Newport, Sriram Praneeth Isanaka, Frank Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

As high-strength aluminum alloys present several processability issues with additive manufacturing (AM), Scalmalloy®, an Al-Mg-Sc-Zr-based alloy, has been developed. This alloy is age-hardenable, allowing it to precipitate out a strengthening precipitate phase, Al3(Sc,Zr). The manufacturer recommends a single-stage aging treatment at 325 °C for 4 h; however, the majority of the literature studies utilize a powder bed processing known as selective laser melting (SLM) over powder-fed processing directed energy deposition (DED). This study addresses the lack of information on heat treatments for DED fabrication by exploring the application of artificial aging temperatures of 300–400 °C for 2, 4, and 6 …

Experimental And Computational Investigation Of Green Laser Propagation Through Turbulent Medium In A Water Tank, Richard Owusu Adansi

Open Access Theses & Dissertations

Turbulence medium poses significant challenges to the propagation of laser beams, impacting applications such as free-space optical communication, remote sensing, and laser weapons systems. Therefore, comprehending and mitigating turbulence effects are vital for enhancing the performance of these systems. Analysis of a strong turbulence impact on electromagnetic wave propagation requires extensive knowledge of the Earth's atmospheric and Oceanic phenomena and Maxwell's electromagnetic theory of light as a propagating wave of electric and magnetic fields. Optical systems' propagation often encounters Strong Turbulence, causing interference and diffraction. Nonetheless, light propagation through randomly fluctuating media has been an exciting and active area of …

Ultrashort Pulsed Laser Treatment Is Effective At Sterilizing Metal Surfaces For Planetary Protection, Kaleb Mcquillan

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

To prevent forward contamination from microbes aboard spacecraft intended for exploration of solar system bodies there is a need for effective sterilization methods. However, current techniques are both time-consuming and expensive. For example, dry heat sterilization requires removal from the assembly site and several days of treatment. Furthermore, some components such as optics and electronics are not compatible with current sterilization techniques. In this thesis, a novel femtosecond laser surface processing technique for the rapid sterilization of spacecraft hardware is reported. Femtosecond lasers produce extremely high photon fluxes (10²⁹ photons/s*cm², ~0.03 J/cm²) in extremely short …

Development And Processing Of Shape Memory Polymer Composites (Smpcs) For Application In Structural Robotics And Robotic Sensors., Kavish Sudan

Electronic Theses and Dissertations

Shape Memory Polymers (SMPs) have attracted significant attention since their introduction in the 1980s due to their remarkable ability to regain their original shape from a temporarily deformed state when exposed to an external stimulus, typically heat. This shape memory effect, driven by thermal transitions such as the glass transition temperature (T_g) or melting temperature (T_m), has made SMPs highly attractive for applications in soft robotics, aerospace, and biomedical devices. However, SMPs face challenges such as limited mechanical strength, thermal stability, and electrical conductivity, which hinder their broader adoption in advanced applications. To address these challenges, …

Trade-Offs In Lighting For Dic Strain Measurements In Vibration-Based Fatigue Testing, Jacob R. Rigby

All Graduate Theses and Dissertations, Fall 2023 to Present

Vibration based fatigue testing offers a fast and efficient method for determining the breaking point of a material. This method often uses a device, called a strain gage, to measure the deformation of a test sample at a single spot on the test sample. However, these strain gages often break before testing is complete. To overcome this premature break, a laser vibrometer is often used to measure the amount of movement or the speed of the test sample throughout the vibration test. The deformation measured by the strain gage is compared against the amount of movement or velocity of the …

Development Of A Passive Drag Reduction Modification For The 25° Ahmed Body Using Large Eddy Simulation, Skylar Polek

UNLV Theses, Dissertations, Professional Papers, and Capstones

In the field of automotive aerodynamics, the Ahmed body is a generic vehicle-shaped bluff body which is meant to generalize the rear end of fastback and hatchback vehicles. Specifically, an Ahmed body with a rear slant angle of 25° has seen common use due to its resemblance of common rear windshield shapes as well as its notoriously complex wake structure. This research focuses on simulating the flow over a 25° in various situations with an ultimate goal of drag reduction. First, a simple benchmark of the k-ω shear stress transport (SST), large eddy simulation (LES) with the Smagorinsky-Lilly subgrid scale …

Modeling Powder Spreadability In Powder-Based Processes Using The Discrete Element Method, Austin T. Sutton, M. Hossein Sehhat, Ming C. Leu, Joseph W. Newkirk

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Powder-bed fusion (PBF) processes refer to a subset of Additive Manufacturing (AM) techniques where powder is spread on the build-plate before melting (by a laser or electron beam). While PBF processes are attractive due to their ability for realizing complex structures that are either difficult or impossible to create through conventional means, the parts fabricated with these techniques can exhibit defects such as pores, inclusions, and excessive surface roughness. To minimize these defects, much research has been dedicated towards process maturation by optimizing laser or electron beam parameters. However, these developmental efforts typically do not address the recoating process where …

A Study Of Directionality Effects In Three-Beam Coaxial Titanium Wire-Based Laser Metal Deposition, Remy Mathenia, Braden Mclain, Todd Sparks, Frank Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Coaxial wire-based laser metal deposition is a versatile and efficient additive process that can achieve a high deposition rate in the manufacturing of complex structures. In this paper, a three-beam coaxial wire system is studied, with particular attention given to the effects of the deposition direction and laser beam orientation on the resulting bead geometry symmetry. With the three-beam laser delivery, the laser spot pattern is not always symmetric with respect to the deposition direction. Single titanium beads are deposited in different directions and at varying deposition rates, and the bead profile is quantitatively scored for multiple symmetry measures. Through …

Analytical And Fem Models For Thermal Analysis And Residual Stresses Using Wire Arc-Based Welding And Additive Manufacturing Of Sus304, Muhammad Arif Mahmood, Usman Tariq, Mihai Oane, Frank Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Austenitic stainless steel, also known as SUS304, has a wide industrial application. The resultant residual stresses and deformation due to arc welding play a critical role in an in-service SUS04 part failure. Various experimental studies have been presented to predict residual stresses and part deformation. However, these techniques are expensive and time-consuming owing to the trial-and-error approach, limiting their application to industrial applications. Based on the emergent need, this study introduces two simulation models based on analytical and FEM techniques for thermal distribution and residual stress estimation. The experimentally calibrated models results have been implemented for SUS304 multi-pass arc welding. …

In Situ Synthesis, Characterization And Photocatalytic Efficacy Of Silver-Enhanced Mxene And Graphene Nanocomposites, Kishore Chand, M. Mustafa Azeem, Muhammad Nazim Lakhan, Mukhtiar Ahmed, Muhammad Jehanzaib Aslam, Ahmer Hussain Shah

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The emergence of 2D materials has significantly expanded the wide range of nanomaterials with diverse applications. Notably, their high conductivity, catalytic efficiency, and hydrophobicity have fueled heightened research interests for water treatment applications. This research aimed to investigate the synthesis and characterization of MXene and reduced graphene oxide (rGO) nanocomposites with silver nanoparticles (Ag) for enhanced catalytic activity in the decomposition of Direct Blue-24 dye. In this study, we employed well-established methods, previously documented in the literature, to prepare two distinct nanocomposites. Novel nanocomposites, namely reduced graphene oxide–silver nanoparticles (rGO–Ag) and MXene–silver nanoparticles (MXene–Ag), were synthesized using the hydrothermal and …

In Situ Synthesis, Characterization And Photocatalytic Efficacy Of Silver-Enhanced Mxene And Graphene Nanocomposites, Kishore Chand, M. Mustafa Azeem, Muhammad Nazim Lakhan, Mukhtiar Ahmed, Muhammad Jehanzaib Aslam, Ahmer Hussain Shah

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The emergence of 2D materials has significantly expanded the wide range of nanomaterials with diverse applications. Notably, their high conductivity, catalytic efficiency, and hydrophobicity have fueled heightened research interests for water treatment applications. This research aimed to investigate the synthesis and characterization of MXene and reduced graphene oxide (rGO) nanocomposites with silver nanoparticles (Ag) for enhanced catalytic activity in the decomposition of Direct Blue-24 dye. In this study, we employed well-established methods, previously documented in the literature, to prepare two distinct nanocomposites. Novel nanocomposites, namely reduced graphene oxide–silver nanoparticles (rGO–Ag) and MXene–silver nanoparticles (MXene–Ag), were synthesized using the hydrothermal and …

Board 125: Work In Progress: Faculty Experiences And Learning Through Oral-Assessment Implementation In Engineering Courses, Minju Kim, Carolyn L. Sandoval, Josephine Relaford-Doyle, Torus Washington Ii, Saharnaz Baghdadchi, Nathan Delson, Marko Lubarda, Alex M. Phan, Curt Schurgers, Huihui Qi

Psychology Faculty Articles and Research

This WIP qualitative research paper explores faculty experiences with implementing oral exams in high-enrollment undergraduate engineering courses at a research university. With a primary goal to improve conceptual mastery, as well as a desire to ensure academic integrity in the sudden move to remote instruction at the height of the pandemic, a group of faculty in Mechanical and Aerospace Engineering and Electrical and Computer Engineering departments implemented oral assessments in their own engineering courses across several quarters. They formed a research group with educational developers in a teaching and learning center on campus, and investigated the impact of oral assessments …

Turbine Cooling System With Energy Separation, James L. Rutledge, Matthew N. Fuqua, Carol M. Bryant

AFIT Patents

A method and system for cooling an engine and/or vehicle using energy separation is disclosed herein. An energy separation device is operable for separating a compressed gaseous coolant stream into a first relatively cooler coolant flow stream and a second relatively hotter coolant flow stream. The relative cooler coolant flow stream is directed to a first region requiring increased cooling and the relative hotter coolant flow stream is directed to a second region requiring lower cooling than the first region in the engine or vehicle.

Using Dft On Ultrasound Measurements To Determine Patient-Specific Blood Flow Boundary Conditions For Computational Hemodynamics Of Intracranial Aneurysms, Hang Yi, Zifeng Yang, Luke Bramlage, Bryan Ludwig

Mechanical and Materials Engineering Faculty Publications

Boundary conditions (BCs) is one pivotal factor influencing the accuracy of hemodynamic predictions on intracranial aneurysms (IAs) using computational fluid dynamics (CFD) modeling. Unfortunately, a standard procedure to secure accurate BCs for hemodynamic modeling does not exist. To bridge such a knowledge gap, two representative patient-specific IA models (Case-I and Case-II) were reconstructed and their blood flow velocity waveforms in the internal carotid artery (ICA) were measured by ultrasonic techniques and modeled by discrete Fourier transform (DFT). Then, numerical investigations were conducted to explore the appropriate number of samples (N) for DFT modeling to secure the accurate BC by comparing …

F56: Rocket Thrust Vector Control, Ethan Douglas Anderson, Yiming Trent Jia, Sahil Sampat

Mechanical Engineering

This Final Design Review (FDR) report compiles relevant information regarding the Rocket Thrust Vector Control senior project as sponsored by Ethan Anderson from Cal Poly Space Systems (CPSS). Documented in this report is our progress from the months following our Critical Design Review (CDR) completion. This consists of a brief overview of the design our thrust vector control (TVC) system and its subassemblies with design changes noted, a thorough walkthrough of our procurement, manufacturing, and assembly process for creating our verification prototype (including software), a breakdown of how we verified each of our specifications through inspection and testing and the …

Sizing Wind Tunnel Heater For High Enthalpy Conditions, Justin M. Slavick

Master's Theses

This paper determines the feasibility of adding a heater to an existing blowdown supersonic wind tunnel to unlock new high-enthalpy test applications, considering cost and power requirements at a variety of different states. This process includes both modeling the current range of test section properties in Cal Poly's blowdown wind tunnel and determining the new range of properties that a heat exchanger could induce. These results are verified with a computational fluid dynamics study. Additionally, sublimation and ablation properties of materials are explored to create appropriate models to study atmospheric re-entry once the heat exchanger is implemented.

It is found …

Heat Sink With Fins And Phase Change Material For Cooling Of High-Power Electronic Devices, Farooq Fakher Mahmoud

Theses

Electronics are integral to modern life, present in everything from household appliances to advanced computers. The performance and reliability of these devices are closely tied to their operating temperatures. High-power operations can lead to significant heating, necessitating effective thermal management to enhance functionality and prevent failure. This requirement drives the demand for efficient heat sinks, which dissipate the heat generated by these devices. Phase change material (PCM)-based heat sinks have become a popular passive cooling solution, increasingly replacing traditional heat sinks.

This research investigates finned PCM-based heat sinks using numerical simulations validated by existing literature and experimental data. Gallium is …

The Pressure Distribution Of Rotating Cylinders Using An Onboard Wireless Data Acquisition System, Nathan Eller

Master's Theses

This thesis presents a novel, cost-effective method for mapping the pressure distribution on a rotating cylinder in cross flow, a phenomenon central to the Magnus effect. Utilizing commercial-off-the-shelf (COTS) micro-electromechanical system (MEMS) pressure sensors, a high-resolution data acquisition system was developed and integrated into a rotating cylinder model. Compared to traditional approaches, such as slip rings or one-off designs, this method proved significantly cheaper and faster while achieving comparable or superior resolution. The experimental setup, including a modified continuous rotation technique and adaptable model design, facilitated rapid testing across a broad range of Reynolds numbers and reduced frequencies, exceeding the …

Interaction Of Particles With Plasma And Shock Produced By Pulsed Spark Discharge, Shomik Mukhopadhyay

Dissertations

Interactions of powders with high-temperature plasma and shockwaves occur in diverse scenarios, such as nuclear blasts, accidental industrial dust explosions, solid propellant combustion in explosive charges and when removing contaminants from surfaces. Electrostatic Discharge (ESD), known for generating shock and plasma, is a promising lab-scale technique for simulating these interactions. Studies with ESD involved placing powders near a spark-producing gap between electrodes and observing mechanical and chemical processes like particle motion and ignition. A limited range of spark conditions and material properties have been tested, which facilitated the development and validation of preliminary computational models describing this system. Significant gaps …

Reproducible Fluid Structure Interaction For Complex Flows In Engineered Systems, Allen Prasad Varghese

Dissertations

This dissertation focuses on the application of numerical models to study Fluid Structure Interaction (FSI) in the industrial context. The emphasis is on a series of case studies belonging to practical applications in design and manufacturing and that are solved by a synergistic use of theoretical and computational models. The first study looks into the hydrodynamic actions experienced by vibrating slender structures immersed in viscous fluids near the free surface. This study case is relevant to applications such as, for example, marine propulsion, micro-electro-mechanical systems, and atomic force microscopy. The hydrodynamic problem is governed by three parameters, namely the frequency, …

Infrared Phase-Change Chiral Metasurfaces With Tunable Circular Dichroism, Haotian Tang, Liliana Stan, David A. Czaplewski, Xiaodong Yang, Jie Gao

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Integrating Phase-Change Materials in Meta surfaces Has Emerged as a Powerful Strategy to Realize Optical Devices with Tunable Electromagnetic Responses. Here, Phase-Change Chiral Meta surfaces based on GST-225 Material with the Designed Trapezoid-Shaped Resonators Are Demonstrated to Achieve Tunable Circular Dichroism (CD) Responses in the Infrared Regime. the Asymmetric Trapezoid-Shaped Resonators Are Designed to Support Two Chiral Plasmonic Resonances with OppositeCDresponses for Realizing SwitchableCDbetween Negative and Positive Values using the GST Phase Change from Amorphous to Crystalline. the Electromagnetic Field Distributions of the Chiral Plasmonic Resonant Modes Are Analyzed to Understand the Chiroptical Responses of the Meta surface. Furthermore, the …

Regular Algorythms For Synthesis Of Optimal Control Systems For Dynamic Objects, Igamberdiyev Husan, Uktam Farkhodovich Mamirov, Xankeldiyeva Zebiniso

Technical science and innovation

The article presents algorithms for the synthesis of an optimal control system for dynamic objects. As a model, we consider a differential equation of a continuous one-dimensional system in the form of a state space, which has the properties of controllability and observability. The paper shows the need to use an observation device in order to assess how the properties of the controlled system change with the slightest change in the parameters of the control object, to assess the sensitivity of the system to these changes. When finding a solution to the equation formulated to find the parameters of the …

Heat Sink Integrating Phase Change Materials For Cooling High Power Electronic Devices, Mohammad Sameer Qasem

Thesis/ Dissertation Defenses

This research explores the numerical analysis of phase change materials (PCMs) heat sinks, focusing on high heat flux dissipation applications, e.g. electronics cooling. Both 2D and 3D numerical models using gallium and paraffin RT31 as PCMs are considered within a heat sink design framework featuring a rectangular cavity and dual opposing vertical copper walls serving as fins to dissipate heat from the hot sink base that receives heat from the heat source. The inclusion of a Triply Periodic Minimal Surface (TPMS) ‘Primitive’ structure as an in-fill thermal conductivity enhancer (TCE) in the case of the gallium heat sink, and a …

Emulsion Stability, Rheological Properties, And Combustion Characteristics Of Waterjojoba Biofuel Emulsion, Ihab Mohamed Ayad

Thesis/ Dissertation Defenses

This thesis comprehensively investigates the stability, rheological properties, and engine performance implications of water in jojoba biodiesel (WJBD) emulsion. The research delves into multiple aspects, including the influence of diverse surfactants and water concentrations on emulsion stability. It also yields valuable insights into the development of stable water in jojoba biodiesel emulsions, specifically tailored for diesel engines. These insights contribute significantly to the body of knowledge of positioning emulsion fuels as viable alternative to traditional diesel fuels. The anticipated benefits include notable reductions in emissions. Importantly, this study underscores the critical importance of considering emulsion stability, both during storage and …

Studying The Production Of Nanocelluloses, Shohzodbek Abduvahobovich Rashidov, Elmurod Abduqodirovich Egamberdiev, Sadritdin Maxamatdinovich Turabdjanov

Technical science and innovation

Nanoscience is a broad field that includes nanophysics and nanochemistry. Nanotechnologies are aimed at obtaining nanoparticles with new properties and creating materials and devices based on them. This is one of the modern trends in the development of science in the 21st century.

Based on the study of information about nano-sized materials, the mechanisms of their production and changes in their properties, we will consider the technology for producing nanocellulose from organic substances, i.e. from cellulose. The article describes a technology that examines devices for producing nanocellulose and the principles of their operation, as well as a combined method of …

Comparative Analysis Of Cutting Forces In Axial-Compliant And Rigid Chamfering Tools, Sultonmurod Bekpulatovich Normatov, Oybek Tuyboyov, Azimjon Axror O'G'Li Pardayev, Alisher G‘Ayratjon Ogli Boratov, Shohjahon Tuxtasin Ogli Abdullayev

Technical science and innovation

This study delves into the analysis of cutting forces in axial-compliant systems, focusing specifically on the comparison between axially spring-compensated 90° conical tools and rigid chamfering tools. The research incorporates a predictive model for chamfer size calculation in the axially spring-compensated tools, verified through experimental tests on representative parts. The study aims to control chamfer size within tolerances by adjusting process conditions and optimizing processing efficiency. By exploring the fundamentals of the chamfering process, this research offers insights into breaking sharp edges on components with positional errors and shape deformations, with a particular emphasis on aero-engine casings. The integration of …

Numerical Investigation Of Supersonic Flow Over A Wedge By Solving 2d Euler Equations Utilizing The Steger–Warming Flux Vector Splitting (Fvs) Scheme, Mitch Wolff, Hashim H. Abada, Hussein Awad Kurdi Awad Kurdi Saad

Mechanical and Materials Engineering Faculty Publications

Supersonic flow over a half-angle wedge (θ = 15°) with an upstream Mach number of 2.0 was investigated using 2D Euler equations where sea level conditions were considered. The investigation employed the Steger–Warming flux vector splitting (FVS) method executed in MATLAB 9.13.0 (R2022b) software. The study involved a meticulous comparison between theoretical calculations and numerical results. Particularly, the research emphasized the angle of oblique shock and downstream flow properties. A substantial iteration count of 2000 iteratively refined the outcomes, underscoring the role of advanced computational resources. Validation and comparative assessment were conducted to elucidate the superiority of the Steger–Warming flux …

Rasc-Al Large Scale Lunar Crater Prospector, Austin Arnold, Coleman Alvarez, Mark Suberu

Senior Design Project For Engineers

The purpose of this project is to design a conceptual layout of a lunar rover capable of exploring craters at the lunar south pole. The rover should be autonomous and capable of self-sustainment for at least one year in extreme cold and darkness. While determining the location and accessibility of water ice and other volatiles within the crater. This document will contain all information related to the team's conceptual design. Including research, component selection, electrical design, and mechanical design.

Lunar Rascals Video: https://www.youtube.com/watch?v=MdcjzVMtzaI

Transfer-Learning-Enhanced Regression Generative Adversarial Networks For Optimal Evtol Takeoff Trajectory Prediction, Shuan Tai Yeh, Xiaosong Du

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Electric vertical takeoff and landing (eVTOL) aircraft represent a crucial aviation technology to transform future transportation systems. The unique characteristics of eVTOL aircraft include reduced noise, low pollutant emission, efficient operating cost, and flexible maneuverability, which in the meantime pose critical challenges to advanced power retention techniques. Thus, optimal takeoff trajectory design is essential due to immense power demands during eVTOL takeoffs. Conventional design optimizations, however, adopt high-fidelity simulation models in an iterative manner resulting in a computationally intensive mechanism. In this work, we implement a surrogate-enabled inverse mapping optimization architecture, i.e., directly predicting optimal designs from design requirements (including …