Mechanical Engineering Commons^™

The Investigation Of Noise, Vibrations And Emissions Of Aero-Gas Turbine Combustion With Synthetic Kerosene Fuels, Margaret Kilpatrick

Honors College Theses

Climatic changes from aviation emissions are complex and include effects of greenhouse gases such as: CO2, NOx, and aerosols. For that reason, the objectives of this study were to investigate the noise, vibrations and emissions characteristics of synthetic kerosene combustion in an aerospace gas turbine to reduce the engine’s environmental impact. Sustainably produced synthetic kerosene is known for having low soot emissions due to little to no aromatics (compounds that create particle pollutants), and for being a sustainable alternative fuel source to imported oil. The noise and sound levels were collected using Bruel & Kjaer microphones to measure various mid …

Ultrasonic Wave Propagation In Copper/Graphene Metal Matrix Composites, Casey Lindbloom

Mechanical Engineering Undergraduate Honors Theses

Emerging metallic composite materials implanted with graphene sheets are showing immense promise, with benefits being observed with regards to mechanical, thermal, and electrical material properties. This research aims to investigate the effects on ultrasonic wave propagation in Copper/Graphene Metal Matrix Composites (Cu/Gr MMCs) with varying graphene arrangements inspired from nacre and bone nanoscale material distributions. To accomplish this, the molecular dynamics (MD) method is utilized to simulate nanoscale wave propagation on a set of Cu/Gr MMCs with differing graphene arrangements and volume percentages ranging up to 4.56%. The computational model results are then analyzed to determine the variation in energy …

Dynamic Pressure Sensing For The Flight Test Data System, Marc Y. Goupil

Master's Theses

This thesis describes the design, assembly, and test of the FTDS-K, a new device in the Boundary Layer Data System (BLDS) family of flight data acquisition systems. The FTDS-K provides high-frequency, high-gain data acquisition capability for up to two pressure sensors and an additional three low-frequency pressure sensors. Development of the FTDS-K was separated into a core module, specialized analog subsystem, and practical testing of the FTDS-K in a flow measurement mission. The core module combines an nRF52840-based microcontroller module, switching regulator, microSD card, real-time clock, temperature sensor, and trio of pressure sensors to provide the same capabilities as previous-generation …

Average Speech Directivity, Samuel D. Bellows, Claire M. Pincock, Jennifer K. Whiting, Timothy W. Leishman

Directivity

Speech directivity describes the angular dependence of acoustic radiation from a talker’s mouth and nostrils and diffraction about his or her body and chair (if seated). It is an essential physical aspect of communication affecting sounds and signals in acoustical environments, audio, and telecommunication systems. Because high-resolution, spherically comprehensive measurements of live, phonetically balanced speech have been unavailable in the past, the authors have undertaken research to produce and share such data for simulations of acoustical environments, optimizations of microphone placements, speech studies, and other applications. The measurements included three male and three female talkers who repeated phonetically balanced passages …

Analytical Approach To Investigation Of Free Vibration Of Thin Rectangular Plate Immersed In Fluid, Resting On Winkler And Pasternak Foundations, Obanishola Sadiq, Gbeminiyi Sobamowo, Saheed Salawu

Karbala International Journal of Modern Science

Dynamic behaviour of free vibration of rectangular plate is investigated. This study considered an analytical approach to investigation of free vibration of thin rectangular plate immersed in fluid, resting on Winkler and Pasternak foundations.The governing nonlinear partial differential equation is analyzed using two-dimensional differential transform method. The accuracy of the analytical solutions obtained is verified with existing results in literature and confirmed in excellent agreement. Thereafter, the analytical solutions are used for investigation of effect of elastic foundation, fluid and aspect ratio on vibrating plate.From the result, it is observed that, increase elastic foundation parameters increases natural frequency, increase aspect …

Data Multiplexing In Vector Acoustic Communication: System Design And Experiments, Erjian Zhang

Dissertations

Acoustic particle velocity channels, which are vector components of the acoustic field, have been recently explored to achieve communication purposes underwater. Vector sensors and transducers that can utilize acoustic particle velocity channels have compact multichannel designs, which are perfect for compact size underwater platforms. In this dissertation, an underwater acoustic multiple-input multiple-output (MIMO) communication system featuring orthogonal frequency division multiplexing (OFDM) and frequency shift keying (FSK) modulation is discussed. By transmitting multiple independent data streams simultaneously over several channels within the same bandwidth, the proposed MIMO system increases the transmission rate. A variety of components of the system such as …

An Analysis Of Perceptual Masking Between Stems In Manually-Mixed Multitrack Audio Using A Cross-Analytic Loudness Model, Brian H. Cofer

Student Theses

In music production, there are many tools available to an audio engineer throughout the mixing process to bring a song to completion. Among the most common are level balancing, equalization (EQ), and compression. However, these tools still require the subjective judgments of human engineers to create the desired listening experience. While automated mixing algorithms have been increasingly studied, they have yet to match the skills of even an amateur mixing engineer, in major part, because the subjective mixing decisions of an engineer are difficult to replicate by automated systems. The following research was developed with the primary goal of objectively …

Parameter Estimation And Dynamic State Observer Design For Vapor Compression Systems, Travis D. Pruitt

Boise State University Theses and Dissertations

Between cooling our house, our workplace, and keeping our food cold both in home and commercially (among other uses), the vapor compression cycle (VCC) is a common method for removing heat from various environments and it accounts for a significant amount of the energy used throughout the world. Therefore, with an ever-growing demand for more efficient processes and reduced energy consumption, improving the ability to accurately model, predict the performance of, and control VCC systems is beneficial to society as whole.

While there is much information available regarding the performance for some of the components found in VCC systems, much …

Design Optimization, Analysis, And Control Of Walking Robots, Wankun Sirichotiyakul

Boise State University Theses and Dissertations

Passive dynamic walking refers to the dynamical behavior of mechanical devices that are able to naturally walk down a shallow slope in a stable manner, without using actuation or sensing of any kind. Such devices can attain motions that are remarkably human-like by purely exploiting their natural dynamics. This suggests that passive dynamic walking machines can be used to model and study human locomotion; however, there are two major limitations: they can be difficult to design, and they cannot walk on level ground or uphill without some kind of actuation.

This thesis presents a mechanism design optimization framework that allows …

System Integration Of C-Arm Robotic Prototype Using Motion Capture Guidance For Accurate Repositioning, Alireza Yazdanshenas

Mechanical Engineering Theses

One of the important surgical tools in spinal surgery is the C-Arm X-ray System. The C-Arm is a large “C” shaped and manually maneuvered arm that provides surgeons and X-ray technicians the ability to take quick quality X-rays during surgery. Because of its five degrees of freedom, the C-Arm can be manually maneuvered around the patient to provide many angles and perspectives, ensuring surgical success.

This system works fine for most surgical procedures but falls short when the C-Arm must be moved out of the way for complicated surgical procedures.

The aim of this thesis is to develop an accurate …

Investigation Of Fundamental Principles Of Rigid Body Impact Mechanics, Khalid Alluhydan

Mechanical Engineering Research Theses and Dissertations

In impact mechanics, the collision between two or more bodies is a common, yet a very challenging problem. Producing analytical solutions that can predict the post-collision motion of the colliding bodies require consistent modeling of the dynamics of the colliding bodies. This dissertation presents a new method for solving the two and multibody impact problems that can be used to predict the post-collision motion of the colliding bodies. Also, we solve the rigid body collision problem of planar kinematic chains with multiple contacts with external surfaces.

In the first part of this dissertation, we study planar collisions of Balls and …

Electronic Cvt - Controls, Alec William Hardy, Jessalyn Leora Ann Bernick, Nicholas Esteban Capdevila, Tristan Charles Perry

Mechanical Engineering

The following document outlines the design process, manufacturing, and testing of the control system for an electronically controlled continuously variable transmission (ECVT). This control system was integrated into the custom designed and manufactured mechanical transmission system created in parallel by another senior project group. The transmission was designed for use in the Cal Poly Baja SAE vehicle. Through researching customer needs, competition requirements, previous and alternate CVT designs, and vehicle characteristics, we were able to determine the requirements and specifications for our unique system. Input, output, speed, and durability requirements guided our hardware selection. The primary components which comprised our …

Reducing The Noise Impact Of Unmanned Aerial Vehicles By Flight Control System Augmentation, Matthew B. Galles

Mechanical & Aerospace Engineering Theses & Dissertations

The aim of this thesis is to explore methods to reduce the noise impact of unmanned aerial vehicles operating within acoustically sensitive environments by flight control system augmentation. Two methods are investigated and include: (i) reduction of sound generated by vehicle speed control while flying along a nominal path and (ii) reduction of acoustic exposure by vehicle path control while flying at a nominal speed. Both methods require incorporation of an acoustic model into the flight control system as an additional control objective and an acoustic metric to characterize primary noise sources dependent on vehicle state. An acoustic model was …

Maximizing And Modeling Malonyl-Coa Production In Escherichia Coli, Tatiana Thompson Silveira Mello

LSU Master's Theses

In E. coli, fatty acid synthesis is catalyzed by the enzyme acetyl-CoA carboxylase (ACC), which converts acetyl-CoA into malonyl-CoA. Malonyl-CoA is a major building block for numerous of bioproducts. Multiple parameters regulate the homeostatic cellular concentration of malonyl-CoA, keeping it at a very low level. Understanding how these parameters affect the bacterial production of malonyl-CoA is fundamental to maximizing it and its bioproducts. To this end, competing pathways consuming malonyl-CoA can be eliminated, and optimal nutritional and environmental conditions can be provided to the fermentation broth. Most previous studies utilized genetic modifications, expensive consumables, and high-cost quantification methods, making …

A Methodology For Verification Of Structural Standards For A Seating System By Finite Element Analysis, Zachary Kelly Dworaczyk Wiltshire

Master's Theses

Currently California Polytechnic State University has a patent pending on a new type of seating system designed to increase the functionality of public transportation vehicles. The patent is based on the work completed by a senior project group in 2016, whose design showcased the feasibility of the idea. Further development was completed by a second senior project group, the Adjustable Seating Systems, in 2019. The intent of the Adjustable Seating Systems group was to develop a seating system with the intent of commercialization and implementation in paratransit vehicles with future development into large buses and trains.

Seating systems used in …

Listener Evaluation Of Common Drum Recording And Mixing Techniques, Tucker W. Arbuthnot

Student Theses

This thesis explored whether listeners could perceive the differences between samples recorded and mixed according to methods reported by the so-called popular audio press and samples that did not utilize those methods. The three recording methods were: aligning multiple tracks to achieve a coherent phase relationship, microphone selection, and the style of recording. The three mixing methods were: inverting the bottom snare drum microphone to match the top snare drum microphone, having a pre-delay time on a reverb that matched the tempo of the sample, and routing the room microphones to the drummer’s perspective. ABX listening tests, preference surveys, and …

Physical Controllers Vs. Hand-And-Gesture Tracking: Evaluation Of Control Schemes For Vr Audio Mixing, Justin Bennington

Student Theses

Alternative control schemes for affecting the characteristics of audio signals have been designed and evaluated within the audio research community. The medium of virtual reality (VR) presents a unique method of sound source visualization using a headset which displays a virtual environment to the user, allowing users to directly control sound sources with minimal intermediary interference with a variety of different controllers. In order to provide insight into the design and evaluation of VR systems for audio mixing, the differences in subject preference between physical controllers and hand-and-gesture detection controls were investigated. A VR audio mixing interface was iteratively developed …

Mid-Side To X/Y Equivalence: Turning Microphone Theory Into Practice, Brent T. Hauer

Student Theses

The mathematical transformation of the Mid-Side microphone array (M-S) to stereophonic left and right outputs results in an equivalent coincident microphone configuration (X/Y). The output pattern of the combined mid (M) and side (S) signals can be altered by manipulating the polar pattern of the mid (M) microphone and by adjusting the ratio between the M and side (S) microphones. This study investigated the technical and perceptual attributes of equivalent M-S and X/Y patterns in order to determine the consistency of the theoretical with the practical application. A simulated jazz sextet was recorded using a selection of M-S, and their …

Motor Control Systems Analysis, Design, And Optimization Strategies For A Lightweight Excavation Robot, Austin Jerold Crawford

Graduate Theses and Dissertations

This thesis entails motor control system analysis, design, and optimization for the University of Arkansas NASA Robotic Mining Competition robot. The open-loop system is to be modeled and simulated in order to achieve a desired rapid, yet smooth response to a change in input. The initial goal of this work is to find a repeatable, generalized step-by-step process that can be used to tune the gains of a PID controller for multiple different operating points. Then, sensors are to be modeled onto the robot within a feedback loop to develop an error signal and to make the control system self-corrective …

Stability Analysis Of A More General Class Of Systems With Delay-Dependent Coefficients, Chi Jin, Keqin Gu, Islam Boussaada, Silviu-Iulian Niculescu

SIUE Faculty Research, Scholarship, and Creative Activity

This paper presents a systematic method to analyse the stability of systems with single delay in which the coefficient polynomials of the characteristic equation depend on the delay. Such systems often arise in, for example, life science and engineering systems. A method to analyze such systems was presented by Beretta and Kuang in a 2002 paper, but with some very restrictive assumptions. This work extends their results to the general case with the exception of some degenerate cases. It is found that a much richer behavior is possible when the restrictive assumptions are removed. The interval of interest for the …

Autonomous Vehicles Operating Collaboratively To Avoid Debris And Obstructions, Toan T. Le, Cole W. Oppenheim, James H. Gildart, Kyle M. Bybee

Mechanical Engineering

The purpose of this project is to demonstrate the safety and increased fuel efficiency of an automated collision avoidance system in collaborative vehicle platooning. This project was cosponsored by Daimler Trucks North America headquartered in Portland, Oregon, as well as Dr. Birdsong, and Dr. DeBruhl of Cal Poly. The mechanical engineering team consists of Cole Oppenheim, James Gildart, Toan Le, and Kyle Bybee who worked in coordination with a team of computer engineers. Vehicle platooning is a driving technique to increase the fuel efficiency of a group of vehicles by following a lead vehicle closely to reduce the drag experienced …

Comparison Of Lqr And Lqr-Mrac For Linear Tractor-Trailer Model, Kevin Richard Gasik

Master's Theses

The United States trucking industry is immense. Employing over three million drivers and traveling to every city in the country. Semi-Trucks travel millions of miles each week and encompass roads that civilians travel on. These vehicles should be safe and allow efficient travel for all. Autonomous vehicles have been discussed in controls for many decades. Now fleets of autonomous vehicles are beginning their integration into society. The ability to create an autonomous system requires domain and system specific knowledge. Approaches to implement a fully autonomous vehicle have been developed using different techniques in control systems such as Kalman Filters, Neural …

Less-Than-Lethal Self Defense Device With An Acoustic Element, Anthony Taibi

KSU Journey Honors College Capstones and Theses

This creative capstone project involves the conception, design, and creation of a less-than-lethal self defense device with an integrated sound board to control the acoustic element. Theoretically, this device is capable of deterring potential threats without causing any serious harm or any long-term damage. When starting this project, I was very focused on sonic warfare, and how to harness the power of ultrasonic and infrasonic sound waves to subdue to target; however, I concluded that using resonant frequencies to deter a human being is too dangerous, expensive, and can have negative effects for the user of the device if used …

Analysis Of Dynamic Behaviour Of A Tensioned Carbon Nanotube In Thermal And Pressurized Environments, Ahmed Yinusa, Gbeminiyi Sobamowo

Karbala International Journal of Modern Science

In this paper, the dynamic behaviour of a tensioned single-walled carbon nanotubes (SWCNT) in thermal and pressurized environments is investigated analytically. With the applications of Bernoulli-Euler and thermal elasticity mechanics theories, the governing equation of motion are developed and solved using Laplace and Fourier transforms. The results of the close form solution in this work are in excellent agreements with past results in literature. From the parametric studies, it is established that as the magnitude of the pressure distribution at the surface increases, the deflection associated with the nanotube increases at any mode of vibration. However, a corresponding increase in …

Design Of A Low-Cost Data Acquisition System For Rotordynamic Data Collection, Gregory S. Pellegrino

Master's Theses

A data acquisition system (DAQ) was designed based on the use of a STM32 microcontroller. Its purpose is to provide a transparent and low-cost alternative to commercially available DAQs, providing educators a means to teach students about the process through which data are collected as well as the uses of collected data. The DAQ was designed to collect data from rotating machinery spinning at a speed up to 10,000 RPM and send this data to a computer through a USB 2.0 full-speed connection. Multitasking code was written for the DAQ to allow for data to be simultaneously collected and transferred …

Composite Recycler: Frame, Alfonso Olivera

All Undergraduate Projects

How can composites be recycled? The Composite Recycler is an ongoing project that started in September 2017. The purpose of this project was to create a machine that will delaminate the composites, cut them, and heat them up to separate the resin from the composites so they can be recycled. A group was put together for the 2018-2019 academic year to further the project as a whole improve the operation of the device. The existing base was used as well as the cutter and the power sources. The upgrades included; a housing to support the transport rollers and changing from …

System Dynamics And Control, Benjamin Liaw

Open Educational Resources

Model development with applications to mechanical engineering systems. First and higher order system responses. Laplace transform, transfer functions and block diagrams. Frequency response and vibration. Introduction to feedback control. Concepts of PID control, tuning and compensation. Routh-Hurwitz stability. Control analysis and design using various graphical methods such as root locus, Bode diagram, Nyquist plot and Nichols chart. Hands-on experiments include dynamics and controls of mechanical, servo motor, fluid level/flow, pneumatic and temperature processing systems and vibration of various degree-of-freedom systems.

Development Of A Muffler Insertion Loss Flow Rig, Jonathan Chen

Theses and Dissertations--Mechanical and Aerospace Engineering

Mufflers and silencers are commonly used to attenuate noise sources such as internal combustion engines and HVAC systems. Typically, these environments contain mean flow that can affect the acoustic properties of the muffler components and may produce flow generated noise. To characterize the muffler performance, common metrics such as insertion and transmission loss and noise reduction are used in industry. Though transmission loss without flow is often measured and is a relatively simple bench top experiment and useful for model validation purposes, mean flow can significantly affect the muffler performance. There are a few existing and commercial transmission loss rigs …

Determination Of Acoustic Radiation Efficiency Via Particle Velocity Sensor With Applications, Steven Conner Campbell

Theses and Dissertations--Mechanical and Aerospace Engineering

Acoustic radiation efficiency is defined as the ratio of sound power radiated to the surface vibration power of a piston with equivalent surface area. It has been shown that the radiation efficiency is maximized and may exceed unity when the structural and acoustic wavelengths are approximately equal. The frequency at which this occurs is called the critical frequency and can be shifted with structural modifications. This has proven to be an effective way to reduce noise. The standard radiation efficiency measurement is comprised of an intensity scan for sound power measurement and accelerometer array for spatially averaged vibration determination. This …

The Effects Of System Characteristics, Reference Command, And Command-Following Objectives On Human-In-The-Loop Control Behavior, Seyyedalireza Seyyedmousavi

Theses and Dissertations--Mechanical and Aerospace Engineering

Humans learn to interact with many complex physical systems. For example, humans learn to fly aircraft, operate drones, and drive automobiles. We present results from human-in-the-loop (HITL) experiments, where human subjects interact with dynamic systems while performing command-following tasks multiple times over a one-week period. We use a new subsystem identification (SSID) algorithm to estimate the control strategies (feedforward, feedforward delay, feedback, and feedback delay) that human subjects use during their trials. We use experimental and SSID results to examine the effects of system characteristics (e.g., system zeros, relative degree, system order, phase lag, time delay), reference command, and command-following …