Mechanical Engineering Commons^™

Design, Testing And Neural Network Modeling Of A Low-Friction Wave Energy Converter Testbed, Vasu Bhardwaj

Dissertations, Master's Theses and Master's Reports

Point absorber wave energy converters (WECs) transform water wave kinetic energy into other useful forms, typically electrical. While it’s possible to extract energy from passive WECs, more energy can be captured using active control where its power take-off (PTO) acts as both a generator and an actuator. Control strategies usually require accurate models often obtained during model-scale testing. Unfortunately, friction can dominate the dynamic response in small WEC models. A frictionless point absorber WEC testbed is described in this report which allows the researcher to focus on fundamental hydrodynamic behavior instead of friction. It uses air bearings for vertical motion …

Comprehensive Review And Development Of A High-Pressure Hydraulic Impedance Tube For Vibroacoustic Attenuator Characterization, Matthew D. Beals

Dissertations, Master's Theses and Master's Reports

This research establishes a versatile test bench for characterizing hydraulic vibroacoustic attenuators. The primary evaluation metric is the transfer matrix, determined experimentally, with an emphasis on key properties such as transmission loss. To ensure accuracy and broad applicability, the methodology is based on industry-standard techniques for determining the transfer matrix. A comprehensive literature review consolidates existing approaches for hydraulic attenuator characterization. The test bench features a hydraulic impedance tube equipped with eight dynamic pressure transducer (DPT) taps strategically positioned before and after the sample interface. This setup accommodates arbitrary samples terminated with standard hydraulic fittings. Using ASTM E2611, the transfer …

Railroad Condition Monitoring Using Distributed Acoustic Sensing And Deep Learning Techniques, Md Arifur Rahman

College of Graduate Studies: Theses & Dissertations

Proper condition monitoring has been a major issue among railroad administrations since it might cause catastrophic dilemmas that lead to fatalities or damage to the infrastructure. Although various aspects of train safety have been conducted by scholars, in-motion monitoring detection of defect occurrence, cause, and severity is still a big concern. Hence extensive studies are still required to enhance the accuracy of inspection methods for railroad condition monitoring (CM). Distributed acoustic sensing (DAS) has been recognized as a promising method because of its sensing capabilities over long distances and for massive structures. As DAS produces large datasets, algorithms for precise …

Investigation Of Topologically Protected Wave Propagation Near Dirac-Like Cones In Acoustic Metamaterials, Md Arif Iqbal Khan

College of Graduate Studies: Theses & Dissertations

This study presents a novel approach to investigate an exceptionally rare acoustic phenomenon – topologically protected wave propagation (TPWP) within a solid-solid domain. While previous research has attempted to unravel the physics behind this phenomenon, most efforts have been grounded in the framework of condensed matter physics and quantum mechanics often requiring complex geometries to realize TPWP in solid-fluid interactions. In contrast, this thesis introduces a geometric tuning method that enables the achievement of TPWP with simpler geometric configurations within a solid-solid domain. Rather than explaining by the quantum trio - quantum anomalous hall effect, quantum valley hall effect, and …

Measurement Of The Local Static Mechanical Pressure Of Earplugs, Luiz G.C. Melo, Ahmed S. Dalaq, Franck Sgard, Olivier Doutres, Laurianne Legroux, Eric Wagnac

Études primaires

Earplugs are used in various critical industrial sectors, such as construction, aviation, military and defense, transportation, and healthcare. However, they present inherent drawbacks, notably discomfort that can lead to inconsistent and incorrect use, thereby leaving a significant proportion of workers vulnerable to irreversible hearing damage, ranging from tinnitus to deafness. This discomfort is closely linked to a physical parameter known as static mechanical pressure (SMP), representing the pressure exerted by earplugs on the earcanal walls. Determining the SMP is crucial for developing earplugs that prioritize comfort. However, experimental studies in this area are scarce and there is no experimental set-up …

Dynamics Of A 3-D Inlet/Isolator Measured With Fast Pressure-Sensitive Paint, Andrew N. Bustard, Mark E. Noftz, Mitsugu Hasegawa, Hirotaka Sakaue, Joseph S. Jewell, Nicholas J. Bisek, Thomas J. Juliano

Publications

Fast pressure-sensitive paint (PSP) was applied to an inlet/isolator designed using the Osculating Internal Waverider Inlet with Parallel Streamlines (OIWPS) method. The dorsal isolator surface pressure was measured using anodized-aluminum PSP through transparent cast acrylic that makes up the ventral portion of the isolator. Temperature-sensitive paint was utilized to correct for the PSP’s temperature sensitivity. The model was tested under Mach 5.7 flow at Re = 8.5 ×106 /m and 10.2 ×106 /m in the AFOSR–Notre Dame Large Mach-6 Quiet Tunnel (ANDLM6QT) under conventional noise conditions. Flow phenomena, such as shocks originating in the inlet and flow separation at the …

Depressurization Characteristics Of Steam-Based Reciprocating Vacuum Pump, Hongling Deng

Dissertations

This dissertation introduces a novel vacuum technology that leverages low-pressure saturated steam and cooling-controlled condensation, offering an efficient way to utilize low-grade thermal energy sources like waste heat, steam, or solar energy. At the heart of this technology is a unique duo-chamber vacuum pump system, featuring a reciprocating piston and a heat-conductive wall, designed to generate a vacuum through steam-condensation and cooling processes.

The core of this research lies in developing and validating mechanistic models for the steam-condensation depressurization process, a complex phenomenon involving phase change and transport mechanisms. Prior to this work, these mechanisms were not sufficiently modeled or …

Développement D’Un Système De Mesure Pour La Caractérisation Des Traitements Absorbants En Laboratoire, Alain Berry, Olivier Robin, Thomas Dupont, Franck Sgard

Rapports de recherche scientifique

Le bruit constitue une préoccupation de plus en plus importante et généralisée dans le monde. Selon l’Organisation mondiale de la Santé, environ une personne sur quatre dans le monde souffrira de déficience auditive à des degrés divers d’ici à 2050. Dans de nombreux pays et régions du globe, le bruit représente le second facteur environnemental provoquant le plus de dommages sanitaires, et ce derrière la pollution atmosphérique. Sur un volet cognitif ou perceptif, le bruit environnemental peut par exemple perturber le sommeil et gêner l’apprentissage en milieu scolaire. Dans un milieu de travail, il peut perturber la bonne compréhension/perception de …

Silver Sintering Reliability And Its Enhancement For Use In High-Density Power Modules, Alicia Medina Garcia

Graduate Theses and Dissertations

This master's thesis is dedicated to enhancing the reliability of silver sinter die attachments, a pivotal component within the dynamic realm of power electronics. The study is meticulously organized into four distinct chapters, each contributing to a comprehensive understanding of silver sinter die attachment reliability and its implications for contemporary electronic packaging. In Chapter 1, an introduction is provided to the significance of silver sinter die attachment in the context of power electronics, underlining the imperatives associated with miniaturization, weight reduction, and heightened efficiency. The compelling need to investigate die attachment properties, particularly in high-temperature and high-power-density environments, is emphasized. …

Model Of Surface Waves On A Viscoelastic Material In A Cylindrical Container With Edge Constraints, Phillip Wilson

All Theses

A theoretical model is developed for the resonant frequencies and mode shapes of pinned edge surface waves on a viscoelastic fluid contained in a finite depth cylindrical container. A boundary integral approach is used to map the governing equations to the domain boundary. The surface waves obey an eigenvalue operator equation that depends on four dimensionless parameters: the cylinder aspect ratio, the Bond number, the Ohnesorge number, and the elastocapillary number. A solution is constructed using a Rayleigh-Ritz variational procedure over a constrained function space, which is able to effectively incorporate the pinned edge boundary condition. Mode shapes are defined …

Accelerated Testing Of Solder Spheres Under Combined Temperature, Current, And Shear Stresses To Estimate Reliability, Collin Ruby

Graduate Theses and Dissertations

With the densification of power electronics in the pursuit of decreased size and weight and increased efficiency, the need to investigate the properties of solder in packages with higher working temperatures and power densities is becoming apparent. Many research groups have conducted accelerated testing using methods such as thermal aging, shear or tensile stress tests, or electromigration tests, but relatively little research exists that considers the impact of several stresses in a combined study. This work aims to produce a novel method for estimating the lifetime of SAC305 solder joints under a combined stress scenario, which more accurately depicts the …

Trust-Based Variable Impedance Control And Passivity-Based Switched System Analysis For Human-Robot Cooperative Manipulation, Zhanrui Liao

All Dissertations

Human-robot cooperative manipulation (co-manipulation) is one of the most prominent human-robot collaboration (HRC) tasks, where humans and robots manipulate the same object. Trust in HRC is crucial in determining human acceptance of robots and, hence, robot utilization. A probabilistic dynamic Bayesian network (DBN) trust model that integrates a time-series trust model is presented in this thesis. The trust model is learned using a continuous and normalized Baum-Welch (BW) algorithm, devised to account for the continuous nature of trust evolution and the limitations of the classic parameter learning method. To ensure a good HRC in co-manipulation, a variable impedance control framework …

Controlled Manipulation And Transport By Microswimmers In Stokes Flows, Jake Buzhardt

All Dissertations

Remotely actuated microscale swimming robots have the potential to revolutionize many aspects of biomedicine. However, for the longterm goals of this field of research to be achievable, it is necessary to develop modelling, simulation, and control strategies which effectively and efficiently account for not only the motion of individual swimmers, but also the complex interactions of such swimmers with their environment including other nearby swimmers, boundaries, other cargo and passive particles, and the fluid medium itself. The aim of this thesis is to study these problems in simulation from the perspective of controls and dynamical systems, with a particular focus …

Impacts Of Connected And Automated Vehicles On Energy And Traffic Flow: Optimal Control Design And Verification Through Field Testing, Tyler Ard

All Dissertations

This dissertation assesses eco-driving effectiveness in several key traffic scenarios that include passenger vehicle transportation in highway driving and urban driving that also includes interactions with traffic signals, as well as heavy-duty line-haul truck transportation in highway driving with significant road grade. These studies are accomplished through both traffic microsimulation that propagates individual vehicle interactions to synthesize large-scale traffic patterns that emerge from the eco-driving strategies, and through experimentation in which real prototyped connected and automated vehicles (CAVs) are utilized to directly measure energy benefits from the designed eco-driving control strategies. In particular, vehicle-in-the-loop is leveraged for the CAVs driven …

Ultrasonic Non-Destructive Evaluation Of Additively Manufactured Polymer-Ceramic Composites, Christian Alexander Ruiz

Open Access Theses & Dissertations

Digital light processing (DLP) is an attractive additive manufacturing technique due to its ability to create ceramic parts with complex geometries. DLP uses ultraviolet light to polymerize a slurry comprised of ceramic powder and photosensitive resin in layers to create solid parts. Printing parameters such as light intensity and exposure time are critical when producing these parts. Improper parameters can lead to over or under-curing, adversely impacting print quality and strength. Samples were printed at varying layer exposure times and then tested using ultrasonics to determine the degree of conversion. Additionally, ultrasonics were used as a non-destructive technique to obtain …

Safe Navigation Of Quadruped Robots Using Density Functions, Andrew Zheng

All Theses

Safe navigation of mission-critical systems is of utmost importance in many modern autonomous applications. Over the past decades, the approach to the problem has consisted of using probabilistic methods, such as sample-based planners, to generate feasible, safe solutions to the navigation problem. However, these methods use iterative safety checks to guarantee the safety of the system, which can become quite complex. The navigation problem can also be solved in feedback form using potential field methods. Navigation function, a class of potential field methods, is an analytical control design to give almost everywhere convergence properties, but under certain topological constraints and …

Physics-Based Machine Learning Methods For Control And Sensing In Fish-Like Robots, Colin Rodwell

All Dissertations

Underwater robots are important for the construction and maintenance of underwater infrastructure, underwater resource extraction, and defense. However, they currently fall far behind biological swimmers such as fish in agility, efficiency, and sensing capabilities. As a result, mimicking the capabilities of biological swimmers has become an area of significant research interest. In this work, we focus specifically on improving the control and sensing capabilities of fish-like robots.

Our control work focuses on using the Chaplygin sleigh, a two-dimensional nonholonomic system which has been used to model fish-like swimming, as part of a curriculum to train a reinforcement learning agent to …

Path Planning Development Framework For Mobile Robots, Lauren-Ann Elizabeth Graham

Theses and Dissertations

Planetary exploration relies on methods of path planning to achieve autonomous navigation in hazardous environments. Simulating harsh terrain, real-time varying physics, and robotics applications is vital for testing control algorithms here on Earth. Robotics Operating System (ROS) is a set of software libraries and tools that allow you to build and simulate robotic applications. Utilizing ROS, Gazebo, and Blender, a rough terrain simulation framework is created to explore and compare path planning algorithms using various desired robots and maps. ROS supports multiple path planning algorithms given its open-source abilities. This research focuses on path planning implementation of Proportional-Integral-Derivative (PID) control …

Mining Multibeam Transit Data For Deep Ocean Polymetallic Nodules: Case Study In Se Pacific Ocean, Mark E. Mussett

USF Tampa Graduate Theses and Dissertations

Occurrences of nodules on the seafloor represent benthic habitats and present potential deposits of economically important metals. Better understanding their extent throughout Earth’s oceans will aid in resource management and determining different factors which influence their formative factors and respective local characteristics. Multibeam bathymetry and backscatter data, along with auxiliary data suggest an area of seafloor near the Foundation Seamount chain in the southern Pacific Ocean, centered around -36.84° latitude, -119.75° longitude, contains a previously uncharted polymetallic nodule occurrence. Our analysis of Simrad EM12 DUAL (12 kHz) multibeam data, collected during a 1997 transit, shows an area of strong backscatter …

Hardware-In-The-Loop Reaction Wheel Testbed With Camera Vision, Abigail Romero, Harvey Perkins, Stephen Kwok-Choon

College of Engineering Summer Undergraduate Research Program

Reaction wheels are widely used in aerospace systems as a method of attitude control. This research was focused on the design, development, and testing of a hardware-in-the-loop reaction wheel testbed that can be used for research and teaching applications related to satellite navigation and control. This project successfully utilized commercial off-the-shelf components to develop a reaction wheel capable of controlling the orientation of a freely rotating platform, as well as tracking objects using computer vision.

Sociotechnical Thinking In Statics And Dynamics, Raul Espinoza

College of Engineering Summer Undergraduate Research Program

This project introduced Canvas modules to instill a sociotechnical mindset in engineering students. By emphasizing the synergy between social and technical systems, the modules aim to produce engineers capable of crafting solutions that are technically adept and socially responsible.

Design And Implementation Of An Optimization Platform For Common Fixed Photovoltaic Systems, Amro Ahmad Zahrawi

Mechanical Engineering Theses

Most household photovoltaic (PV) panels are installed in a fixed arrangement (fixed-type) based on a rule of thumb that comes from experience. The azimuth angle is usually set facing south with a tilt angle equivalent to the location's latitude. However, research shows that this is not the best for all geographical locations and during all hours of the day. Consequently, this brings up the hypothesis that optimizing the PV system's azimuth and tilt angles would ensure that the PV panel produces the most possible output as it is adjusted to face the sun most effectively during peak sunlight hours. This …

Trumpet Directivity From A Rotating Semicircular Array, Samuel D. Bellows, Joseph E. Avila, Timothy W. Leishman

Directivity

The directivity function of a played musical instrument describes the angular dependence of its acoustic radiation and diffraction about the instrument, musician, and musician’s chair. Directivity influences sound in rehearsal, performance, and recording environments and signals in audio systems. Because high-resolution, spherically comprehensive measurements of played musical instruments have been unavailable in the past, the authors have undertaken research to produce and share such data for studies of musical instruments, simulations of acoustical environments, optimizations of microphone placements, and other applications. The authors acquired the data from repeated chromatic scales produced by a trumpet played at mezzo-forte in an anechoic …

A Multi-Aerial Vehicle Platform For Testing Collaborative Mobility Formation Controllers, Matthew Snellgrove

LSU Master's Theses

Multi-agent systems have potential applications in a multitude of fields due to their ability to perform complex tasks with a high degree of robustness. Decentralized systems are multi-agent systems where sensing, control, and communication responsibilities are distributed amongst the agents giving this scheme a particularly high potential for robustness, adaptability, and complexity; however, this comes with its own list of challenges. Formation control is a topic in multi-agent systems that aims to have the agents moving as a virtual rigid body through space. In the literature, there have been successful implementation of formation control algorithms on robot agents in both …

A Robust Model Reduction For The Optimal Boundary Feedback Stabilization Of Magnetizable Piezoelectric Beams, Md Rafi As Sadeq Ibn Emran

Masters Theses & Specialist Projects

The one-dimensional Partial Differential Equation (PDE) model of the wave equation, which describes wave dynamics of a wide-range of controlled mechanical systems, with a state feedback controller at its boundary is known to have exponentially stable solutions. Moreover, it is also reported that the several model reductions of the wave equation by the standard Finite Differences and Finite Elements approximations suffer from the lack of exponential stability (and exact observability without a state feedback controller) uniformly as the discretization parameter tends to zero. This is due to the loss of a uniform gap among the high-frequency eigenvalues as the discretization …

The Effect Of Deployment And Optimal Dispatch Of Shared Electric Shuttles On The Energy Efficiency Of Campus Transit, Robert Smith

All Theses

A problem facing most public transit systems is low energy efficiency and the continued cycling of large transport vehicles such as buses at low occupancy when low demand for transport exists, wasting energy to no benefit. To remedy this issue, we propose a hybrid system consisting of existing diesel buses and automated electric shuttles to augment the system during off-peak hours. Due to their smaller size, higher occupancy, and more efficient powertrains, these shuttles could reduce the system energy used per passenger-mile-traveled. Automation removes the labor cost of drivers and, thus, eliminates the need to employ more drivers for the …

Co-Simulation Of Active Magnetic Bearing Rotors Using Adams, Msc Apex, And Simulink, Shea A. Charkowsky

Master's Theses

Apex-Adams-Simulink co-simulation is applied to active magnetic bearing (AMB) rotors, demonstrating results unshown in literature, including continuous frequency response, and unavailable in known rotor dynamics software, including touchdown bearing impact. AMBs levitate rotors without contact, so they involve no friction, wear, lubrication, pollution, or shaft speed limits and are thus valuable for large, high-speed applications. Modeling of such rotors, necessary for safety and performance, simultaneously requires flexible body dynamics and advanced control design, but simulation programs tend to specialize in only one or the other. The co-simulation method combines multiple such programs—MSC Apex (finite element modeling), Adams (multibody dynamics), and …

Trust-Based Runtime Verification Of Autonomous Robotic Systems, Maziar Fooladi Mahani

All Dissertations

 Trust plays a crucial role in enabling effective collaboration and decision-making within human-multi-robot teams. In this context, runtime verification techniques and trust inference models have emerged as valuable tools for assessing and quantifying the trustworthiness of individual robots. This dissertation presents a study on trust-based runtime verification and introduces a Bayesian trust inference model for human-multi-robot teams. Firstly, we discuss the concept of runtime verification, which involves monitoring and analyzing the behavior of robots during their operation. We highlight the importance of trust as a key factor in determining the reliability and credibility of robot actions. By integrating trust metrics …

Integrated Energy-Aware Motion Planning And Charge Scheduling Of Unmanned Aerial Vehicles, Hayleyesus Alemayehu

All Theses

The growing demand for unmanned aerial vehicles (UAVs) is driven by their operational convenience, cost-effectiveness, availability, and adaptability to various scenarios. In energy-constrained environments, optimizing energy consumption and ensuring a continuous power supply for UAVs is crucial for mission success. The objective of this thesis is to address this issue by integrating energy-aware motion planning and charge scheduling for UAVs by utilizing a charger hosted on an unmanned ground vehicle (UGV), whose rendezvous locations and routes are jointly computed to minimize overall energy consumption.

This thesis proposes a hierarchical trajectory and control framework comprising local and global planners for each …

Dynamics And Steering Of A Vibration-Driven Bristle Bot In A Pipe System, Ian Stewart

All Theses

Soft vibrational robots are robots that incorporate compliant structures into their design and are driven by oscillating actuators. A recent, popular version of a soft vibrational robot is the bristle bot, which uses flexible bristles and a vibration motor to propel itself across surfaces and through pipes. This motion is primarily driven by stick-slip dynamics resulting from asymmetric frictional forces applied at the bristle tips. Depending on the frequency of vibration of the motor, the robot experiences various resonance regions allowing it to maneuver in different directions. Attaching bristles to all sides of the robot and placing it in a …