Semiconductor and Optical Materials Commons^™

First Announcement Of 76th Annual Meeting Of The International Society Of Electrochemistry, International Society Of Electrochemistry (Ise)

Journal of Electrochemistry

No abstract provided.

Research On 3d Printing Resin Exposure Properties And Its Application On Centrifugal Microfluidic Platform Based On Fluorescence Detection, Zheng Qiao

LSU Doctoral Dissertations

This dissertation encapsulates significant advancements in the field of SLA 3D printing and centrifugal microfluidics. Central to the research is the development of a novel mathematical model for predicting trapped resin thickness in SLA 3D printing, a groundbreaking contribution that addresses a critical aspect of printing intricate structures. This model, the first to establish a mathematical relationship for resin thickness, is rooted in a comprehensive study of the resin curing process. The research leverages the concept of 'critical dosage' for resin curing, leading to a more refined and theoretically grounded approach for calculating curing thickness. Experimentation further validates the model, …

Shorting At Long Duration: Impact Of Extended Discharge Capacity On Battery Solid Electrolytes, Ryan C. Hill, Amanda S. Peretti, Leo J. Small, Erik D. Spoerke, Yang-Tse Cheng

Chemical and Materials Engineering Faculty Publications

Long-duration energy storage (LDES) is critical to a stable, resilient, and decarbonized electric grid. While batteries are emerging as important LDES devices, extended, high-power discharges necessary for cost-competitive LDES present new materials challenges. Focusing on a new generation of low-temperature molten sodium batteries, we explore here unique phenomena related to long-duration discharge through a well-known solid electrolyte, NaSICON. Specifically, molten sodium symmetric cells at 110 ° C were cycled at 0.1 A cm−2 for 1–23 h discharges. Longer discharges led to unstable overpotentials, reduced resistances, and decreased electrolyte strength, caused by massive sodium penetration not observed in shorter duration discharges. …

Recent Advances In Solar Photo(Electro)Catalytic Nitrogen Fixation, Jun-Bo Ma, Sheng Lin, Zhiqun Lin, Lan Sun, Chang-Jian Lin

Journal of Electrochemistry

Ammonia (NH₃) is an essential chemical in modern society. It is currently produced in industry by the Haber-Bosch process using H₂ and N₂ as reactants in the presence of iron-based catalysts at high-temperature (400–600 ^oC) and extremely highpressure (20–40 MPa) conditions. However, its efficiency is limited to 10% to 15%. At the same time, a large amount of energy is consumed, and CO₂ emission is inevitably. The development of a sustainable, clean, and environmentally friendly energy system represents a key strategy to address energy crisis and environmental pollution, ultimately aiming to achieve carbon neutrality. …

Thermal, Electrical, And Spin Transport: Encompassing Low-Damping Ferromagnets And Antiferromagnetic/Ferromagnetic Heterostructures, Matthew Ryan Natale

Electronic Theses and Dissertations

Continuing technological advancements bring forth escalating challenges in global energy consumption and subsequent power dissipation, posing significant economic and environmental concerns. In response to these difficulties, the fields of thermoelectrics, spintronics, and spincaloritronics emerge as contemporary solutions, each presenting unique advantages. Thermoelectric devices, based on the Seebeck effect, other a passive, carbon-free energy generating solution from waste heat. Although current thermoelectric technology encounters hurdles in achieving optimal efficiencies without intricate designs or complex materials engineering, recently research into low-damping metallic ferromagnetic thin films have provided a new method to enhance spin wave lifetimes, thus contributing to thermoelectric voltage improvements. As …

Development Of Synthetically Accessible Glycolated Polythiophenes For High-Performance Organic Electrochemical Transistors, Bowen Ding, Vianna N. Le, Hang Yu, Guanchen Wu, Adam V. Marsh, Edgar Gutiérrez-Fernández, Nicolás Ramos, Martina Rimmele, Jaime Martín, Jenny Nelson, Alexandra F. Paterson, Martin Heeney

Chemical and Materials Engineering Faculty Publications

Four glycolated polythiophene-based organic mixed ionic-electronic conductors (OMIECs), PE2gTT, PE2gT, PT2gTT, and PT2gT are prepared by atom-efficient direct arylation polymerization, avoiding the need for toxic organometallic pre- cursors. PE2gT, PT2gTT, and PT2gT are operable in p-type accumulation mode organic electrochemical transistors (OECTs), with PT2gT displaying the best device performance with a μC* product figure-of-merit of 290 F cm−1 V−1 s−1 . A record volumetric capacitance among p-type glycolated polythiophene OMIECs of 313 F cm−3 is observed for PE2gT, ascribed to the high proportion- ality of polar components in its materials design. The good OECT performance of PE2gT with μC* = …

“Zero” Porosity High Loading Nmc622 Positive Electrodes For Li-Ion Batteries, Haidar Y. Alolaywi, Kubra Uzun, Yang-Tse Cheng

Chemical and Materials Engineering Faculty Publications

LiNi0.6 Mn0.2Co0.2 O 2 (NMC622) is a widely used positive electrode material for lithium-ion batteries, including electric vehicles. In this work, we investigated the effects of porosity, ranging from “zero” to the typical 35%, on the electrochemical behavior of high- loading NMC622 electrodes. Although it is well known that the energy density of the electrode increases with increasing areal capacity and decreasing porosity, NMC-positive electrodes with exceedingly low porosity (e.g., near zero) and high loading (e.g., 4 mAh cm−2 ) have not been investigated. Here, we report an intriguing observation that the “zero porosity” NMC electrode can have higher capacity …

The Effect Of Nanoconfined Liquid Properties On The Water-Responsive Behavior Of Bacterial Cell Walls, Seungri Kim

Dissertations and Theses

Water-responsive (WR) materials have the ability to mechanically swell and shrink in response to changes in relative humidity (RH). These WR materials are used by many biological systems to perform essential tasks; for example, pinecones use WR materials to release their seeds in dry environments, and wheat awns open and close to propel seeds into the soil, driven by daily RH changes. The WR actuation of some biomaterials is extremely powerful, for example Bacillus subtilis cell walls display record-high actuation energy and power densities of 72 MJ m^-3 and 9.1 MW m^-3, surpassing those of all existing …

Elucidating Self-Assembly Of Semiconducting Polymers In The Presence Of A Low Molecular Weight Gelator, Madhubhashini Lakdusinghe

Theses and Dissertations

Semiconducting polymers with a conjugated backbone are important for energy storage, conversion, and biomedical field applications. The self-assembly process of these polymers in solutions depends on the polymer concentration and quality of the solvent. The electrical properties of thin films obtained from the solution phase depend on the self-assembled process. Thin films of conjugated polymer gels with percolating networks of self-assembled structures display improved electrical conductivities. In this dissertation, we studied the impact of the secondary gel matrix formed by a low molecular weight gelator, on the self-assembly of conjugated polymers, the preservation of assembled structures in dried gel films …

Investigation Of Light Management Strategies And Photochemistry Of Si/Tio2 Tandem Microwire Slurries For Solar Hydrogen Generation., Saumya Gulati

Electronic Theses and Dissertations

The intermittent nature of the Sun makes it difficult to use it as a primary source of electricity and often needs to be supplemented by electricity from the grid which comes from fossil fuels. This motivates the need for solar energy storage. Photoelectrochemical (PEC) water-splitting has been explored as a means to convert solar energy into hydrogen (and oxygen), which can be stored as fuel. The current method of coupling PV and electrolyzer units has been widely commercialized, however, the cost of H₂ generated is far from the target of $1/kg set by the DOE under the Energy EarthShot …

Synthesis Of Quasi-Freestanding Graphene Films Using Radical Species Formed In Cold Plasmas, Michael A. Mathews Jr.

Graduate Theses, Dissertations, and Problem Reports (ETD)

For over a decade, the Stinespring laboratory has investigated scalable, plasma assisted synthesis (PAS) methods for the growth of graphene films on silicon carbide (SiC). These typically utilized CF₄-based inductively coupled plasma (ICP) with reactive ion etching (RIE) to selectively etch silicon from the SiC lattice. This yielded a halogenated carbon-rich surface layer which was then annealed to produce the graphene layers. The thickness of the films was controlled by the plasma parameters, and overall, the process was readily scalable to the diameter of the SiC wafer.

The PAS process reproducibly yielded two- to three-layer thick graphene films …

A Circular Economy Approach To Improve E-Waste Recycling In California: Economic Potential And Policy Options, Kripa Shah

Master's Projects and Capstones

The higher consumption rates of electronic devices along with their short life cycles and few repair options poses a huge challenge for E-waste industries to manage them effectively. E-waste comprises of hazardous materials and toxic constituents that can affect the environment and public health through improper disposal. However, they also contain few valuable materials that, if recovered, can reduce the dependence on virgin raw materials. Circular economy has the potential to utilize these valuable materials and gain environment and socio-economic benefits. The research explains how the adoption of a circular economy approach can help improve the E-waste recycling in California …

Reactive Thin Film Polymers And Thin Film Composite Membranes For The Rapid Screening Of Uranium Isotopes, Abenazer W. Darge

All Dissertations

Traditional radiochemistry approaches for the detection of trace-level alpha-emitting radioisotopes in water require lengthy offsite sample preparations and do not lend themselves to rapid quantification. Therefore, a novel platform is needed that combines onsite purification, concentration, and isotopic screening with a fieldable detection system. My dissertation research objective was to develop novel reactive thin polymer films and thin film composite membranes for the selective separation of uranium from environmental water followed by direct isotopic analysis by alpha spectroscopy. Chapter 1 reviews progress made on uranium separation from aqueous matrices and discusses methods used for the determination of isotopic composition.

Chapter …

Preparation Of Pt@Basrtio3 Nanostructure And Its Properties Towards Photoelectrochemical Ammonia Synthesis, Jing Zhang, Rui-Xia Guo, Jian-Jun Fu, Shi-Bin Yin, Pei-Kang Shen, Xin-Yi Zhang

Journal of Electrochemistry

Ammonia is an important industrial raw material and a potential green energy. Using renewable energy to convert nitrogen into ammonia under ambient condition is an attractive method. However, the development of efficient photoelectrochemical ammonia synthesis catalysts remains a challenge. Perovskite such as BaSrTiO₃ (BST) is a good photocatalytic material. However, BST is active under ultraviolet light and has a high recombination rate of photogenerated electron-hole pairs. By dispersing precious metals, it can effectively regulate the absorption of sunlight by BST. In this work, we used a two-step method to prepare BST. The H₂PtCl₆·6H₂O …

Design And Fabrication Of Nanostructured Electrodes For Complementary Electrochemical And Photoelectrochemical Water Splitting, Kholoud El Sayed Abousalem

Theses and Dissertations

Designing highly active, durable, and nonprecious electrodes for overall water splitting is of urgent scientific importance to realize sustainable hydrogen production. Accordingly, the need to search efficient energy production systems is of crucial necessity. In this thesis, two various systems for sustainable hydrogen production have been reported using electrochemical and photoelectrochemical pathways. In the first part of the thesis, electrochemical water splitting involving both hydrogen evolution reaction (HER) and oxygen evolution reaction (OER) has been established. To this end, an innovative approach is demonstrated to synthesize flower-like 3D homogenous trimetallic Mn, Ni, Co phosphide catalysts directly on nickel foam via …

Engineering The Surface Of Fe3o4 Nanoparticles For Catalytic And Magnetic Applications, Natalia Da Silva Moura

LSU Doctoral Dissertations

With the rapid depletion of the U.S. energy resources coupled with population growth, heat management technologies must be improved to sustain our quality of life. Precisely, in catalysis, it is estimated that only ~50% of the energy supplied to the reactor is used for product conversion due to dissipation losses. Among the emerging technologies with a promising reduction in heat losses is induction heating, offering targeted heat delivery with magnetic nanoparticles. Under alternating magnetic fields (AMF), these nanoparticles can absorb the energy from Radio-Frequency (RF) fields and dissipate it as heat on the nanoparticle surface. This in situ heat generation …

Distributed Modeling Approach For Electrical And Thermal Analysis Of High-Frequency Transistors, Amirreza Ghadimi Avval

Graduate Theses and Dissertations

The research conducted in this dissertation is focused on developing modeling approaches for analyzing high-frequency transistors and present solutions for optimizing the device output power and gain. First, a literature review of different transistor types utilized in high-frequency regions is conducted and gallium nitride high electron mobility transistor is identified as the promising device for these bands. Different structural configurations and operating modes of these transistors are explained, and their applications are discussed. Equivalent circuit models and physics-based models are also introduced and their limitations for analyzing the small-signal and large-signal behavior of these devices are explained. Next, a model …

Assessment Of Heavy Metal Concentration In Soils Around Geita The Gold Mine, Tanzania, Mariam G. Mgendi, Mkabwa L. K Manoko, W.J.S. Mwegoha, C. Southway C. Southway

Journal of Humanities and Social Sciences

Health issues related to gold mining cannot be underestimated. Gold mining produce acid mine drainage (AMD), which in turn releases heavy metals into the nearby environment, hence causing environmental pollution. Heavy metals are naturally very toxic, thus pose a great health concern especially when their concentration exceeds the recommended permissible limits. In this study, concentrations of five heavy metals—including Pb, Ni, Cr, Cu and Zn—were assessed in the soil around Geita Gold Mine (GGM). A total of 17 sampling sites were established from which the soil samples were collected at 0-15cm and 15-30cm soil depth. The concentration of both total …

Nature-Inspired Material Strategies Towards Functional Devices, Sayantan Pradhan

Theses and Dissertations

Naturally sourced, renewable biomaterials possess outstanding advantages for a multitude of biomedical applications owing to their biodegradability, biocompatibility, and excellent mechanical properties. Of interest in this dissertation are silk (protein) and chitin (polysaccharide) biopolymers for the fabrication of functional biodevices. One of the major challenges restricting these materials beyond their traditional usage as passive substrate materials is the ability to combine them with high-resolution fabrication techniques. Initial research work is directed towards the fabrication of micropatterned, flexible 2D substrates of silk fibroin and chitin using bench-top photolithographic techniques. Research is focused on imparting electrochemical properties to silk proteins using conducting …

Development Of Light Actuated Chemical Delivery Platform On A 2-D Array Of Micropore Structure, Hojjat Rostami Azmand, Hojjat Rostami Azmand

Dissertations and Theses

Localized chemical delivery plays an essential role in the fundamental information transfers within biological systems. Thus, the ability to mimic the natural chemical signal modulation would provide significant contributions to understand the functional signaling pathway of biological cells and develop new prosthetic devices for neurological disorders. In this paper, we demonstrate a light-controlled hydrogel platform that can be used for localized chemical delivery in a high spatial resolution. By utilizing the photothermal behavior of graphene-hydrogel composites confined within micron-sized fluidic channels, patterned light illumination creates the parallel and independent actuation of chemical release in a group of fluidic ports. The …

Perovskite Thin Films Annealed In Supercritical Fluids For Efficient Solar Cells, Gilbert Annohene

Theses and Dissertations

In the field of photovoltaics, scientists and researchers are working fervently to produce a combination of efficient, stable, low cost and scalable devices. Methylammonium lead trihalide perovskite has attracted intense interest due to its high photovoltaic performance, low cost, and ease of manufacture. Their high absorption coefficient, tunable bandgap, low-temperature processing, and abundant elemental constituent provide innumerable advantages over other thin film absorber materials. Since the perovskite film is the most important in the device, morphology, crystallization, compositional and interface engineering have been explored to boost its performance and stability. High temperatures necessary for crystallization of organic-inorganic hybrid perovskite films …

Synthesis, Self-Assembly And High-Pressure Properties Of Nanoparticles And Hybrid Nanocomposites, Lingyao Meng

Nanoscience and Microsystems ETDs

Nanoparticles have gained significant scientific interests owing to their unique structural dimensions, size- and shape-tunable properties, and numerous fascinating applications, from opto-electronics, sensor devices, to energy, environmental, and medical fields. Furthermore, the synergistic integration of other materials, including organic polymers, with nanoparticles provides new opportunities and strategies to obtain nanocomposites with superior properties and functionalities. While there is already significant research on the synthesis and characterizations of nanoparticles and hybrid nanocomposites, some research questions, such as how to design and control the interfacial morphology in polymer/nanoparticle hybrid nanocomposites, how to synthesize metal- organic framework (MOF) nanoparticles in well-defined and uniform …

Pollution Prevention Via Recovery Of Cerium (Iv) Oxide In Optics Company, Eugene Park, William Gallagher, Sydor Optics, Flint Creek Resources

Articles

Pollution prevention methods were applied at an optics manufacturer in an effort to improve recovery of a valuable polishing component, cerium oxide (ceria), 77% of which was lost to dragout and sewer discharge. Centrifugation and microfiltratiion were evaluated to develop a process that would increase recovery of used ceria, which would then be sent back to the ceria supplier for reclamation and reuse. Full-scale implementation included a high-speed centrifuge that operates continuously with a microfiltration system through recirculation in a single process tank. Sydor Optics has improved ceria recovery from 23% to 48%, saving thousands of dollars annually.

Noble-Transition Alloy Absorbers For Near-Infrared Hot-Carrier Optoelectronics, Sara Karoline Figueiredo Stofela

LSU Doctoral Dissertations

Optoelectronics is the field of technology concerned with the study and application of electronic devices that source, detect and control light. Here we focus on the optical communications field which relies on optical fiber systems to carry signals to their destinations operating in the near-infrared range. To improve the performance of current optical fiber systems, one of the paths is to develop better near-infrared photodetectors.

The current group of materials used for near-infrared photodetection relies in the III-V semiconductor family. Although their spectral photosensitivity correlates well with the near-infrared, response time performance and electronic circuit integration remain limited for this …

Fabrication, Characterization And Applications Of Highly Conductive Wet-Spun Pedot:Pss Fibers, Ruben Sarabia Riquelme

Theses and Dissertations--Chemical and Materials Engineering

Smart electronic textiles cross conventional uses to include functionalities such as light emission, health monitoring, climate control, sensing, storage and conversion of energy, etc. New fibers and yarns that are electrically conductive and mechanically robust are needed as fundamental building blocks for these next generation textiles.

Conjugated polymers are promising candidates in the field of electronic textiles because they are made of earth-abundant, inexpensive elements, have good mechanical properties and flexibility, and can be processed using low-cost large-scale solution processing methods. Currently, the main method to fabricate electrically conductive fibers or yarns from conjugated polymers is the deposition of the …

Gravity-Drawing Flexible Silicone Filaments As Fiber Optics And Model Foldamers, Katherine Snell

CMC Senior Theses

Here, we present a method of gravity-drawing polydimethylsiloxane (PDMS) silicone fibers with application as fiber optics and as model foldamers. Beginning as a viscous liquid, PDMS is cured using heat until its measured viscosity reaches 4000 mPa•s. The semi-cured elastomer is then extruded through a tube furnace to produce thin (diameters on the order of hundred micrometers) filaments with scalable lengths. PDMS is biocompatible, gas-permeable, flexible, and hydrophobic. Additionally, the PDMS surface hydrophobicity can be modified via UV exposure, O2 plasma, and corona discharge. We demonstrate the patternibility (i.e patterns of hydrophobicity) of PDMS fibers, adding complexity to potential foldamer …

Structure, Morphology And Composition-Property Elucidation Of Ni–Mo And Ni−Mo−P Nanocrystals For Water Splitting Reactions And Group Iv Alloy And Silicate Nanocrystals For Visible To Near Ir Optoelectronics, Ebtesam Hassan Abuelenein Eladgham

Theses and Dissertations

Abstract

Structure, Morphology and Composition-Property Elucidation of Ni–Mo and Ni−Mo−P Nanocrystals for Water Splitting Reactions and Group IV Alloy and Silicate Nanocrystals for Visible to Near IR Optoelectronics

by

Ebtesam Hassan Abuelenein Eladgham

A dissertation submitted in partial fulfillment of the requirements for the degree of Doctor of Philosophy at Virginia Commonwealth University.

Advisor: Indika U Arachchige

Associate Professor, Department of Chemistry

Nanomaterials have gained a great attention because of their unique physical properties with size intermediate between molecular materials and extended solids. They have a large surface to volume ratio and display size tunable physical properties that was not …

Synthesis Of Graphene Using Plasma Etching And Atmospheric Pressure Annealing: Process And Sensor Development, Andrew Robert Graves

Graduate Theses, Dissertations, and Problem Reports (ETD)

Having been theorized in 1947, it was not until 2004 that graphene was first isolated. In the years since its isolation, graphene has been the subject of intense, world-wide study due to its incredibly diverse array of useful properties. Even though many billions of dollars have been spent on its development, graphene has yet to break out of the laboratory and penetrate mainstream industrial applications markets. This is because graphene faces a ‘grand challenge.’ Simply put, there is currently no method of manufacturing high-quality graphene on the industrial scale. This grand challenge looms particularly large for electronic applications where the …

Modeling Of Vapor Sorption In Nanoparticle Chemiresistors, Alexandra Oliveira

Honors Scholar Theses

Chemical vapor sensors possess a number of uses in a variety of fields, from environmental and health monitoring to food safety and national security concerns, such as the detection of improvised explosive devices. Many sensors currently in the market have the ability to detect the presence of a select few compounds and measure the concentration at which the species is present. However, these types of sensors require that the vapor to be investigated is known beforehand; they cannot be used for identification except on a case by case basis. In response to this issue, one branch of vapor sensor research …

Controlled Nanomorphology Of Hybrid Organic/Inorganic Multi-Component Composites Through Cooperative Non-Covalent Interactions, Lingyao Meng

Shared Knowledge Conference

Hybrid organic–inorganic nanocomposite polymers, with inorganic nanoparticles embedded in organic matrix have emerged as a special category of multifunctional materials. With rational materials design, these hybrids can show the synergistic effect of the properties from both phases. Homogenous dispersion and orderly arrangement of the organic and inorganic components are key in their functionalities. By controlling the interface and corresponding interfacial interactions between the organic and inorganic entities, we have developed a logical approach to form stable and controlled hybrid nanofiber structures. We demonstrate the formation of hybrid polymer/quantum dots (or iron oxide nanoparticles) nanocomposites through non-covalent interactions (hydrogen bonding, ionic …