Polymer and Organic Materials Commons^™

Wireless Temperature Monitoring System For The Cal Poly Pilot Winery, Caitlin Devaney

Materials Engineering

This project, with an interdisciplinary group of two computer engineers and one materials engineer, was seeking to implement an automated temperature monitoring system which is affordable and easy to use, as well as adaptable to any arrangement and scale of a winemaker’s fermentation setup. My goal, as the materials engineer, was to design, fabricate, and test the enclosure, for the wireless nodes that are placed in the wine fermentation tanks, and the materials used for the node enclosure. For the enclosure of the system, materials selection was completed using CES software using limitations of only polymer materials which absorb less …

A Least Squares Closure Approximation For Liquid Crystalline Polymers, Traci Ann Sievenpiper

Mathematics & Statistics Theses & Dissertations

An introduction to existing closure schemes for the Doi-Hess kinetic theory of liquid crystalline polymers is provided. A new closure scheme is devised based on a least squares fit of a linear combination of the Doi, Tsuji-Rey, Hinch-Leal I, and Hinch-Leal II closure schemes. The orientation tensor and rate-of-strain tensor are fit separately using data generated from the kinetic solution of the Smoluchowski equation. The known behavior of the kinetic solution and existing closure schemes at equilibrium is compared with that of the new closure scheme. The performance of the proposed closure scheme in simple shear flow for a variety …

Electrical And Structural Studies Of Polyacrylonitrile (Pan) Complexed With Inorganic Salts., Khairul Bahiyah Md Isa

Student Works (2010-2019)

In the present study, polymer electrolyte films composed of polyacrylonitrile (PAN) as a host polymer, ethylene carbonate (EC) as the plasticizer and lithium triflate (LiCF3SO3) and sodium triflate (NaCF3SO3) as dopant salts were prepared by the solution cast technique. Five systems of polymer electrolytes films have been prepared; these systems are the plasticized-PAN system i.e. PAN-EC system, two salted-PAN systems i.e. PAN-LiCF3SO3 and PAN-NaCF3SO3, and two plasticized-salted PAN systems i.e. PAN-EC-LiCF3SO3 and PAN-EC-NaCF3SO3. The pure PAN film was prepared as a reference. The ionic conductivity for each system is characterized using impedance spectroscopy. The room temperature conductivity of the pure …

An Experimental Study Of An Advanced Polymeric Material For Use In Total Knee Replacements Including Gait Analysis Of Mobile Knee Bearings, Lisa Ann Scott

Mechanical & Aerospace Engineering Theses & Dissertations

The primary objectives of this research were to clinically examine the New Jersey Low Contact Stress (LCS)™ Rotating Platform and Meniscal knee bearing systems and to investigate the tribological properties of a new polymer for potential application in total joint replacement. Thus, clinical studies were performed on subjects having the LCSTM Rotating Platform knee bearing and subjects having the LCS™ meniscal knee bearing. The results indicated that there was a statistically significant difference in the braking force for both implant groups when compared to a control group. There was also a statistically significant difference noted for the LCS™ Rotating Platform …

Determinations Of Molecular Weight And Molecular Weight Distribution Of High Polymers By The Rheological Properties, Joan Y. Z. Huang

Mechanical & Aerospace Engineering Theses & Dissertations

Several methods are reviewed by which the molecular weight (MW) and molecular weight distribution (MWD) of polymeric material were determined from the rheological properties. A poly (arylene ether) polymer with six different molecular weights was used in this investigation. Experimentally measured MW and MWD were conducted by GPC/LALLS (Gel Permeation Chromatography/Low Angle Laser Light Scattering), and the rheological properties of the melts were measured by a Rheometric System Four rheometer. It was found that qualitative information of the MW and MWD of these polymers could be derived from the viscoelastic properties, with the methods proposed by Zeichner and Pate1, and …

Removing Fluoride From Drinking Water By Organic Polymers, Eleni Davou Achilleos

Civil & Environmental Engineering Theses & Dissertations

Fluoride is a substance that can provide beneficial or detrimental effects depending on the total amount ingested. Naturally occurring high fluoride concentrations exist in many drinking water supplies. The fluoride removal methods developed in the past have been found to be either impractical and/or not cost effective.

The purpose of this study was to determine whether organic polymers can effectively remove fluoride. The water used in this study contained naturally occurring fluoride concentrations between 4.5 to 5.5 mg/1 and it was collected from the City of Franklin, Virginia, water supply system. Laboratory jar test procedures, which simulated a conventional water …

Analysis Of Moisture Absorption And Diffusion In Fiber Reinforced Polymeric Resin-Matrix Composite Materials, Stephen Stern Tompkins

Mechanical & Aerospace Engineering Theses & Dissertations

The diffusion of moisture through fiber reinforced polymeric-matrix composite materials has been studied analytically. The diffusion in the orthotropic, nonhomogeneous material was modeled, in detail, with a two-dimensional transient diffusion analysis. An effective diffusivity for the composite was determined in terms of the fiber volume fraction and the resin diffusivity. This effective diffusivity is in better agreement with recent data than those previously determined using less complex models.

The influence of both material and environmental parameters on the moisture content of the composite was determined analytically. Predicted moisture contents were compared over a wide range of values for emittance, solar …