Polymer and Organic Materials Commons^™

Highly Flame Retardant And Bio-Based Rigid Polyurethane Foams Derived From Orange Peel Oil, Chunyang Zhang

Electronic Theses & Dissertations

Polyurethane is an important class of polymer which is being used for various industrial applications in the form of rigid foams, flexible foams, thermoplastic, elastomer, coating, and adhesive. Especially there is a huge market for rigid polyurethane foams for their applications as thermal insulating material in building and housing. In general, polyurethanes are prepared using polyols and diisocyanates. Most of the polyols used by industries are petrochemical based. In this project, a novel polyol from an orange peel oil-based derivative, limonene dimercaptan, was synthesized using one step photochemical thiol-ene reaction. The synthesized polyol was used to prepare flame retardant polyurethane …

Corner Sealants For Tactical Shelters, Janine Carlita Nowak

Honors Theses

The demand for a lightweight, easy-assembly tactical shelter is high for those faced with unexpected disasters and global conflicts. This project focuses on designing and prototyping the corner sealant for such a shelter. Two materials were chosen and tested: an in-house thermoplastic polyurethane (TPU) and Texin 950. Thermogravimetric Analysis (TGA) was performed on both of these materials. The in-house TPU showed initial degradation at 282.50 °C and sample degradation at 457.45 °C. Similarly, Texin 950 showed initial degradation at 293.68 °C and sample degradation at 453.26 °C. Differential Scanning Calorimetry (DSC) was then run. The crystallization temperature (Tc) was observed …

Polymer Nanocomposites Containing High Aspect Ratio Particulates: Innovation In Co-Extruded Multilayer Barrier Films, Kevin Meyers

Dissertations

Delaminated montmorillonite (MMT) clay/ maleic anhydride grafted LLDPE nanocomposite multilayer films with alternating layers of LDPE were produced through multilayer co-extrusion. The MMT concentration within the nanocomposite layers was increased through annealing the films in the melt due to a mismatch in interdiffusion rates of the polymer layers. Analysis of the nanocomposite layers upon annealing revealed that the platelets impinged upon one another resulting in significant improvement in oxygen barrier in the multilayer system, exceeding the results of bulk nanocomposites.

Model analysis demonstrated that increasing the nanoplatelet aspect ratio or initial concentration in the filled layers would lead to even …

Characterization And Selection Of Hydroxyl-Terminated Polybutadiene Polymers For High-Strain Applications, Nathaniel Prine

Honors Theses

Understanding the behavior of hydroxyl-terminated polybutadiene (HTPB) as a composite matrix is imperative for the development of future military and aerospace munition technology. As a vital component of solid rocket fuel, HTPB strongly contributes to the fatigue behavior, burn-rate, and other properties that can cause critical failure of the rocket if not formulated properly. The purpose of this research is to identify traits characteristic of poor-performing HTPB matrices by analyzing two samples labeled as either “good” or “bad” based on their performance as a fuel matrix. Samples were analyzed via 1H NMR and GPC to determine their epoxy content, hydroxyl …

Structure And Property Of Polymers And Biopolymers From Molecular Dynamic Simulations, Xiaoquan Sun

Graduate Theses and Dissertations

Natural and synthetic polymers and biopolymers have been studied for a variety of applications in food emulsion, biopharmaceutical purification, tissue engineering, and biosensor. The structure and property of polymers and biopolymers are critically important to determine their functions. Molecular dynamics (MD) simulations have a unique advantage to explore the structure and property of polymers and biopolymers from the molecular level. In the dissertation, MD simulations were conducted to study the mechanisms of various biological and chemical processes controlled by polymers and biopolymers based on real-world experimental results.

Seven heptapeptides have been screened from a peptide library in our earlier study …

Phase Transitions In Monochalcogenide Monolayers, Mehrshad Mehboudi

Graduate Theses and Dissertations

Since discovery of graphene in 2004 as a truly one-atom-thick material with extraordinary mechanical and electronic properties, researchers successfully predicted and synthesized many other two-dimensional materials such as transition metal dichalcogenides (TMDCs) and monochalcogenide monolayers (MMs). Graphene has a non-degenerate structural ground state that is key to its stability at room temperature. However, group IV monochalcogenides such as monolayers of SnSe, and GeSe have a fourfold degenerate ground state. This degeneracy in ground state can lead to structural instability, disorder, and phase transition in finite temperature. The energy that is required to overcome from one degenerate ground state to another …

Self-Assembled Barium Titanate Nanoscale Films By Molecular Beam Epitaxy, Timothy Allen Morgan

Graduate Theses and Dissertations

One challenge of investigating ferroelectrics at the nanoscale has been controlling the stoichiometry during growth. Historically, the growth of barium titanate (BaTiO3) by molecular beam epitaxy has relied on a growth technique called shuttered RHEED. Shuttered RHEED controls the stoichiometry of barium titanate through the precise deposition of alternating layers of BaO and TiO2. While this approach has achieved 1% control of stoichiometry, finding self-limiting mechanisms to lock-in stoichiometry has been the focus of the growth community. The Goldschmidt tolerance factor predicts an unstable perovskite when barium sits in the titanium lattice site. The BaO-TiO2 phase diagram predicts a low-solubility …

The Application Of The Peleg Model In Order To Obtain Completely Soluble Materials For Food Product Packaging, Roxana Puscaselu (Gheorghita), Sonia Amariei

Journal of Applied Packaging Research

The aim of this study was to create a completely hydrosoluble edible films based on biopolymers that can be used as packaging material for powdered foods.10 edible films were obtained from various mixtures of hydrocolloids (agar, starch, sodium alginate) plasticized with glycerol and water. To assess their solubility, it was used the Peleg model which confirmed that increasing the temperature of the hydration medium, increases the water absorption rate. The sample obtained from agar and starch was less hydrophilic than sample with a high amount of sodium alginate, which was completely soluble after 3 minutes maintenance in 20° water. To …

Review Of Challenges And Advances In Modification Of Food Package Headspace Gases, Ziynet Boz, Bruce A. Welt, Jeffrey K. Brecht, William Pelletier, Eric Mclamore, Gregory A. Kiker, Jason E. Butler

Journal of Applied Packaging Research

Modified Atmosphere Packaging (MAP) has been widely used as an effective way to preserve foods. Fresh produce, meat and meat products, seafood, and dairy products can benefit from modified gaseous atmospheres, which are usually achieved by reducing oxygen and increasing carbon dioxide concentrations, within limits, defined by product tolerances. MAP of fresh produce is particularly challenging because products are living and respiring. Respiration rates depend on several factors including temperature, oxygen, and carbon dioxide concentrations. Balancing package permeation with respiration is challenging, often due to limited selection of practical packaging materials. Failing to remain within tolerance limits of products leads …

Waste Management By Waste: Removal Of Acid Dyes From Wastewaters Of Textile Coloration Using Fish Scales, S M Fijul Kabir

LSU Master's Theses

Removal of hazardous acid dyes by economical process using low-cost bio-sorbents from wool industry wastewaters is of a pressing need, since it causes skin and respiratory diseases and disrupts other environmental components. Fish scales (FS), a by-product of fish industry, a type of solid waste, are usually discarded carelessly resulting in pungent odor and environmental burden. In this research, the FS of black drum (Pogonias cromis) were used for the removal of acid dyes (acid red 1 (AR1), acid blue 45 (AB45) and acid yellow 127 (AY126)) from wool industry wastewaters by absorption process with a view to …

Materials Design With Polylactic Acid-Polyethylene Glycol Blends Using 3d Printing And For Medical Applications., Jeremiah R. Bauer

Electronic Theses and Dissertations

This thesis is an examination of two material systems derived from polylactic acid (PLA) and polyethylene glycol (PEG). PLA is a polymer commonly sourced from renewable sources such as starches and sugars. It is a relatively strong, biodegradable polymer, making it ideal for use in the body. Even though it has a relative high strength, PLA is also brittle leading to the use of plasticizers to increase flexibility. One such plasticizer is PEG, which is a material that can exist at room temperature as either a thin liquid, or a hard waxy solid depending on the molecular weight. The first …

Tensile Properties And Fatigue Behavior Of Geopolymer Matrix Composites With Carbon Fiber Reinforcement At Elevated Temperature, Steffan M. L. Wilcox

Theses and Dissertations

The tensile stress-strain and tension-tension fatigue of geopolymer matrix composites reinforced with 0/90 carbon fibers was investigated at 23 and 300°C in laboratory air. Geopolymers are inorganic polymeric materials composed of alumina, silica, and alkali metal oxides. Because geopolymers are synthesized as a fluid mixture or particles and liquid, they can be cast into a desired shape, and cured at only slightly elevated temperatures. The relative ease of synthesis and low processing temperatures make geopolymers an attractive choice as a matrix material for composite materials. Geopolymers also offer resistance to heat and oxidizing environments. Currently, geopolymer matrix composites are being …

Communication And Biodegradable Packaging Relationship: A Paradigm For Final Disposal, Breno Luiz Ottoni, Rafael Mattos Deus, José Alcides Gobbo Junior, Ângela Maria Grossi De Carvalho, Rosane Aparecida Gomes Battistelle

Journal of Applied Packaging Research

Solid waste generation is estimated to increase from 1.3 billion to 2.2 billion tons by 2025, causing environmental, social, and consequently public health problems. The biggest problem in this regard involves the inadequate disposal of waste, and in emerging countries like Brazil, it is sorted less waste for recycling or composting. In this context, plastic packaging is more complex due to the high polymer composition, as well as low recycling rates. Bioplastics appear as alternatives because they are mostly biodegradable. Given the various functions of packaging and a systematic review of the literature, the aim of this study was to …

Application Of Cross-Linked Polyborosiloxanes And Organically Modified Boron Silicate Binders In Silicon-Containing Anodes For Lithium-Ion Batteries, Darius A. Shariaty, Dali Qian, Yang-Tse Cheng, Susan A. Odom

Chemistry Faculty Publications

To determine the effect of cross-linking in polymer binders on gravimetric capacity and retention in charge/discharge cycling of lithium-ion batteries containing silicon anodes, polymers with a varied chemiophysical characters have been studied as electrode binders. Here we report the utilization of cross-linked polyborosiloxanes and a boron-modified organosilicate as binders for nanoparticulate silicon-containing anodes for lithium-ion batteries. We show that highly cross-linked binders enable a large degree of capacity to be accessed and that capacity retention is greater when the electrodes are cycled in half cells. More extensive analysis of the boron-modified organosilicate is further explored.

Surfactant Driven Assembly Of Freeze-Casted, Polymer-Derived Ceramic Nanoparticles On Grapehene Oxide Sheets For Lithium-Ion Battery Anodes, Ali Zein Khater

Honors Undergraduate Theses

Traditional Lithium-Ion Batteries (LIBs) are a reliable and cost-efficient choice for energy storage. LIBs offer high energy density and low self-discharge. Recent developments in electric-based technologies push for replacing historically used Lead-Acid batteries with LIBs. However, LIBs do not yet meet the demands of modern technology. Silicon and graphene oxide (GO) have been identified as promising replacements to improve anode materials. Graphene oxide has a unique sheet-like structure that provides a mechanically stable, light weight material for LIB anodes. Due to its structure, reduced graphene oxide (rGO) is efficiently conductive and resistive to environmental changes. On the other hand, silicon-based …

Design And Analysis Of A 3d-Printed, Thermoplastic Elastomer (Tpe) Spring Element For Use In Corrective Hand Orthotics, Kevin Thomas Richardson

Theses and Dissertations--Mechanical and Aerospace Engineering

This thesis proposes an algorithm that determine the geometry of 3D-printed, custom-designed spring element bands made of thermoplastic elastomer (TPE) for use in a wearable orthotic device to aid in the physical therapy of a human hand exhibiting spasticity after stroke. Each finger of the hand is modeled as a mechanical system consisting of a triple-rod pendulum with nonlinear stiffness at each joint and forces applied at the attachment point of each flexor muscle. The system is assumed quasi-static, which leads to a torque balance between the flexor tendons in the hand, joint stiffness and the design force applied to …

Effect Of Curing Rate On The Microstructure And Macroscopic Properties Of Epoxy Fiberglass Composites, Ammar Patel, Olesksandr Kravchenko, Ica Manas-Zloczower

Mechanical & Aerospace Engineering Faculty Publications

Curing rates of an epoxy amine system were varied via different curing cycles, and glass-fiber epoxy composites were prepared using the same protocol, with the aim of investigating the correlation between microstructure and composite properties. It was found that the fast curing cycle resulted in a non-homogenous network, with a larger percentage of a softer phase. Homogenized composite properties, namely storage modulus and quasi-static intra-laminar shear strength, remained unaffected by the change in resin microstructure. However, fatigue tests revealed a significant reduction in fatigue life for composites cured at fast curing rates, while composites with curing cycles that allowed a …

The Influence Of Organic Pigments On Coating Properties, Sarah Medeiros

Williams Honors College, Honors Research Projects

Abstract

The purpose of this project was to identify the qualities of two synthesized organic pigments added to a coating. These high-performance pigments were benzodipyrrolidone and benzodifuranone, which are π-conjugated monomers. These pigments were each formulated into two different pigment concentrations and compared with a control that had no pigment. This project is limited by time constraints and the number of variables that can be tested in that time. Performance testing was conducted to evaluate the qualities of these coatings. The results demonstrated that the coatings were reproducible and most tests had results that were equal to or exceeded the …

Surface Engineering And Monomer Design For Light-Mediated Ring Opening Metathesis Polymerization, Ishan A. Fursule

Theses and Dissertations--Chemical and Materials Engineering

Stimuli-responsive materials are changing the landscape of actuated materials, optoelectronics, molecular machines, solar cells, temporary memory storage, and biomedical materials. Specifically, photo-responsive polymers have gained acceleration in research and application since the last two decades in the form of a surface coating and micro-patterns. Light as a stimulus can be coherent, mono or polychromatic, tunable for power (intensity) and energy (wavelength), and has precise spatiotemporal control. Conventional surface coating techniques such as spin coating are unable to impart properties to the coatings in terms of sturdiness, homogeneity, uniformity over the complex surface, post deposition modification, and process efficiency. Also, in …

Mixed Matrix Flat Sheet And Hollow Fiber Membranes For Gas Separation Applications, Nicholas W. Linck

Theses and Dissertations--Chemical and Materials Engineering

Mixed matrix membranes (MMM) offer one potential path toward exceeding the Robeson upper bound of selectivity versus permeability for gas separation performance while maintaining the benefits of solution processing. Many inorganic materials, such as zeolites, metal-organic frameworks, or carbon nanotubes, can function as molecular sieves, but as stand-alone membranes are brittle and difficult to manufacture. Incorporating them into a more robust polymeric membrane matrix has the potential to mitigate this issue.

In this work, phase inversion polymer solution processing for the fabrication and testing of asymmetric flat sheet mixed matrix membranes was employed with CVD-derived multiwall carbon nanotubes (MWCNTs) dispersed …

Morphological And Energetic Effects On Charge Transport In Conjugated Polymers And Polymer-Nanowire Composites, Zhiming Liang

Theses and Dissertations--Chemistry

Organic semiconductors have wide applications in organic-based light-emitting diodes, field-effect transistors, and thermoelectrics due to the easily modified electrical and optical properties, excellent mechanical flexibility, and solution processability. To fabricate high performance devices, it is important to understand charge transport mechanisms, which are mainly affected by material energetics and material morphology. Currently it is difficult to control the charge transport properties of new organic semiconductors and organic-inorganic nanocomposites due to our incomplete understanding of the large number of influential variables. Molecular doping of π-conjugated polymers and surface modification of nanowires are two means through which charge transport can be manipulated. …

Evaluation Of Large Area Additively Manufactured Fiber Reinforced Acrylonitrile Butadiene Styrene (Abs), Kevin Schnittker

Open Access Theses & Dissertations

To enable the advancement of large-scale additive manufacturing processes, it is necessary to establish and standardize methodologies to characterize the mechanical properties of printed test coupons. Due to the large size of the print beads, conventional test standards are inadequate. The focus of this study was to determine the feasibility of using Digital image correlation (DIC) technology as a key enabler for robust data collection of strain measurements of large 3D printed parts. To incorporate the DIC measurements, a novel method was developed to prepare large 20 wt.% glass filled ABS test coupons for adequate contrast. Through this technique, Poisson's …

Consuming Digital Debris In The Plasticene, Stephen R. Parks

Theses and Dissertations

Claims of customization and control by socio-technical industries are altering the role of consumer and producer. These narratives are often misleading attempts to engage consumers with new forms of technology. By addressing capitalist intent, material, and the reproduction limits of 3-D printed objects’, I observe the aspirational promise of becoming a producer of my own belongings through new networks of production. I am interested in gaining a better understanding of the data consumed that perpetuates hyper-consumptive tendencies for new technological apparatuses. My role as a designer focuses on the resolution of not only the surface of the object through 3-D …

An Energy-Based Approach To Assess And Predict Erosive Airfoil Defouling, Arthur Rudek, Thomas-Alexander Zitzmann, Geral Russ, Barry Duignan

Articles

A dynamic indentation experiment is presented for assessment of the adhesive behavior of a range of coatings in erosive defouling of commercial aircraft engines using CO2 dry-ice. A series of experiments is presented in which particles made from a reference material (polyoxymethylene – POM) and from CO2 dry-ice are made to impact compressor airfoils under a range of impact angle and velocity conditions. The airfoils investigated are coated with an indicator material (PTFE), which is typically used to visualise the defouling effect in large scale compressor defouling experiments. In addition, fouled compressor airfoils taken from service and coated with a …

Thermal-Fatigue And Thermo-Mechanical Equivalence For Transverse Cracking Evolution In Laminated Composites, Javier Cabrera Barbero

Graduate Theses, Dissertations, and Problem Reports (ETD)

Carbon fiber reinforced plastics (CFRP) are potential materials for many aerospace and aeronautical applications due to their high specif strength/weight and a low coeffcient of thermal expansion (CTE) resulting in a high long-term stability. Among candidate structures, the re-entry reusable launch vehicles (RLV), the fuel oxidant storage and transportation at cryogenic temperature, space satellites, and aircraft structure (frame, wings, etc...) can be highlighted. However, CFRP are prone to internal damage as a result of high residual stresses and thermal fatigue loading. In this study, micro-cracking damage evolution in laminated composites subjected to monotonic cooling and thermal cyclic loads is developed …

An Injectable Thermosensitive Biodegradable Hydrogel Embedded With Snap Containing Plla Microparticles For Sustained Nitric Oxide (No) Delivery For Wound Healing, Nikhil Mittal

Dissertations, Master's Theses and Master's Reports

After injury, wound healing is a complex sequential cascade of events essential for the proper recovery of the wound without the scar formation. Nitric oxide (NO) is a small, endogenous free-radical gas with antimicrobial, vasodilating and growth factor stimulating properties. NO has wide biomedical application especially in wound healing however, its usability is hindered due its administration problem as it is highly unstable.

In this work, poly (l-lactic acid) microparticles encapsulated with NO donor S-nitroso-N-acetyl-D-penicillamine (SNAP) were prepared using water-in-oil-water double emulsion solvent evaporation method for controlled delivery for NO at the specific site. The NO release from SNAP-PLLA microparticles …

Synthesis And Behavior Characterization Of Multi-Scale Hierarchical Structured Composites, Jacob M. Mayfield

College of Graduate Studies: Theses & Dissertations

The purpose of the synthesis of a multi-scale hierarchical composite material was to create a material with a high specific strength, a low mass, and high strength material. To achieve this the material categorization of the Formlabs Tough V2 resin was conducted. The resin was used in the construction of a bio-mimicry diamond lattice structure. The structure was subjected to compression testing to characterize the material properties. The Tough V2 resin structure combined with cellulose created a multi-scaled material on Macro and Micro levels to show the bio-inspired design to increase the material properties in a favorable manor. The Tough …