Polymer and Organic Materials Commons^™

A Soft Condensed Matter Approach Towards Mathematical Modelling Of Mass Transport And Swelling In Food Grains, Michael Chapwanya, N. Misra

Articles

Soft condensed matter (SCM) physics has recently gained importance for a large class of engineering materials. The treatment of food materials from a soft matter perspective, however, is only at the surface and is gaining importance for understanding the complex phenomena and structure of foods. In this work, we present a theoretical treatment of navy beans from a SCM perspective to describe the hydration kinetics. We solve the transport equations within a porous matrix and employ the Flory–Huggin’s equation for polymer–solvent mixture to balance the osmotic pressure. The swelling of the legume seed is modelled as a moving boundary with …

Fatigue Life Prediction Of Magnetorheological Elastomers Subjected To Dynamic Equi-Biaxial Cyclic Loadin, Yanfen Zhou, Stephen Jerrams, Tony Betts, Lin Chen

Articles

Prediction of fatigue life is of great significance in ensuring that dynamically loaded rubber components exhibit safety and reliability in service. In this text, the dynamic equi-biaxial fatigue behaviour of magnetorheological elastomer (MREs) using a bubble inflation method is described. Wöhler (S-N) curves for both isotropic and anisotropic MREs were produced by subjecting the compounds to cycling over a range of stress amplitudes (σ_a) between 0.75 MPa and 1.4 MPa. Changes in physical properties, including variation in stress-strain relations and complex modulus (E*) during the fatigue process were analysed. It was found that the complex modulus of MRE …

The Equi-Biaxial Fatigue Characteristics Of Epdm Under True (Cauchy) Stress Control Conditions, Mark Johnson

Conference Papers

Strain amplitude control is most often employed when carrying out fatigue testing of rubber components. Often the design engineer requires fatigue test data that is based on load amplitude control. This is analogous to engineering or nominal stress amplitude control. This usually makes it easy to maintain the load within the specified test limits during extended testing. Values of true stress and strain can be obtained from this approach, but the magnitudes of the maximum true stresses in these tests increase with accumulated cycles, whereas the equivalent maximum engineering stress values remain constant. This is easily demonstrated in the uniaxial …

The Effect Of Microstructure On The Dynamic Equi-Biaxial Fatigue Behaviour Of Magnetorheological Elastomers, Yanfen Zhou, Stephen Jerrams, Tony Betts, Lin Chen

Conference Papers

Dynamic equi-biaxial fatigue behaviour of isotropic and anisotropic magnetorheological elas-tomers (MREs) based on a silicone rubber matrix was investigated using the bubble inflation method. Con-stant engineering stress amplitude was used as the control mode and samples were fatigued over different stress ranges between 0.75MPa and 1.4MPa. S-N (Wöhler) curves showing plots of stress amplitude (σa) ver-sus cycles to failure (N) are presented. Stress-strain behaviour throughout the fatigue process is described. Elastic modulus (E*) was studied for the specific cycles measured. It was found that anisotropic MREs exhi-bited greater fatigue resistance than isotropic MREs for a given magnetic particle content. Stress …

Prediction Of Compressive Creep Bhaviour In Flexible Polyurethane Foam Over Long Time Scales And At Elevated Temperatures, Conor Briody, Barry Duignan, Stephen Jerrams, Stephen Ronan

Articles

Compressive creep gradually affects the structural performance of flexible polymeric foam material over extended time periods. When designing components, it is often difficult to account for long-term creep, as accurate creep data over long time periods or at high temperatures is often unavailable. This is mainly due to the lengthy testing times and/or inadequate high temperature testing facilities. This issue can be resolved by conducting a range of short-term creep tests and applying accurate prediction methods to the results. Short-term creep testing was conducted on viscoelastic polyurethane foam, a material commonly used in seating and bedding systems. Tests were conducted …

The Implementation Of A Visco-Hyperelastic Numerical Material Model For Simulating The Behaviour Of Polymer Foam Materials, Conor Briody, Barry Duignan, Stephen Jerrams, John Tiernan

Articles

Polyurethane foam has been in use for some time in wheelchair seating systems as it offers good pressure relieving capabilities in most cases. However, little characterisation work has gone into seating foam materials by comparison with conventional elastomeric materials. Accurate material models could allow better prediction of foam in-service behaviour, which could potentially improve seating design practises. The objective of this work was to develop an approach for the validation of hyperelastic and viscoelastic material model parameters used to simulate polyurethane foam behaviour. Material parameters were identified from relevant test procedures and implemented in a Finite Element simulation of an …

The Significance Of Equi-Biaxial Bubble Inflation In Determining Elastomeric Fatigue Properties, Stephen Jerrams, Niall Murphy, John Hanley

Books/Book Chapters

It is well documented that for the effective modelling of the static and dynamic behaviour of elastomeric components using the finite element (FE) method it is essential to obtain material parameters that are derived from a range of physical tests. For a conventional linear solid, uniaxial testing suffices to fully characterise the material, but for rubber it is necessary to test in at least two deformation modes. Also, the determination of fatigue lives of rubber components is still in its infancy and a reliable, repeatable fatigue test for rubber will have important consequences for component design, functionality, maintenance and cost. …

Testing, Modelling And Validation Of Numerical Model Capable Of Predicting Stress Fields Throughout Polyurethane Foam, Conor Briody, Barry Duignan, Stephen Jerrams

Conference Papers

Wheelchair seating systems are specialised for a number of reasons as users can have impaired mobility, which increases the possibility of pressure build up. These areas of high pressure frequently occur in the trunk region under the bony prominences known as the Ischial Tuberosities (IT), pressure ulcers may occur consequently. Polyurethane foam has been in use for some time in wheelchair seating systems as it exhibits good pressure relieving capabilities in most cases. However, little quantitative research has gone into foamed polymers, in comparison with conventional elastomeric materials. This lack of knowledge can ultimately lead to more time being spent …

Characterisation, Modelling And Simulation Of Flexible Polyurethane Foam, Conor Briody, Barry Duignan, Stephen Jerrams

Conference Papers

Flexible polyurethane foam is an open-celled polymeric material that exhibits strain rate and temperature effects. It has found various applications in areas including the packaging, medical, sports, aerospace and aeronautical industries. Polyurethane foam is ubiquitous in seating applications and finds particular use in specialised wheelchair seating where customised seating solutions are required which can provide proper comfort and support without the risk of developing pressure ulcers. Proper seating design is critical for users if this problem is to be avoided, but a lack of quantitative knowledge of this material’s behaviour has limited its effectiveness. The objectives of the work presented …

Big Challenges In Designing Small Parts For Mass Production, Kevin Delaney, David Kennedy

Conference Papers

Micro manufacturing involves the production of parts or products with features on a micro scale. The technology is used to produce parts for several business sectors which have experienced dramatic growth in recent years and forecasts are that this growth will continue in the years ahead. With the loss of traditional manufacturing jobs to lower-cost locations many companies in Ireland see micro manufacturing as having significant potential to preserve and increase revenue. A move into micro manufacturing will present significant opportunities for those companies willing to take the risk of producing parts with micro dimensions. Such a transition is a …

Equi-Biaxial Fatigue Of Elastomers: The Effect Of Oil Swelling On Fatigue Life, Stephen Jerrams, John Hanley, Niall Murphy, Ali Hassan

Articles

The effect of oil swelling on the fatigue life of ethylene propylene diene monomer rubber (EPDM) has been studied under conditions of equi-biaxial cycling using dynamic bubble inflation. Specimens were subjected to varying degrees of swelling in reference mineral oils and fatigued at constant engineering stress amplitudes. The reference oils used for swelling the EPDM had known aniline points, allowing the rubber-oil compatibility to be determined. The inflation fluid for fatigue testing was selected with a solubility parameter that would produce a desired level of incompatibility with the test specimens, thereby limiting the amount of additional swelling during cycling. Wöhler …

Damping Of Magnetorheological Elastomers, Lin Chen

Articles

The damping property of magnetorheological (MR) elastomers is characterized by a modified dynamic mechanical-magnetic coupled analyzer. The influences of the external magnetic flux density, damping of the matrix, content of iron particles, dynamic strain and driving frequency on the damping properties of MR elastomers were investigated experimentally. The experimental results indicate that the damping properties of MR elastomers greatly depend on the interfacial slipping between the inner particles and the matrix. Different from general composite materials, the interfacial slipping in MR elastomers is affected by the external applied magnetic field.

Effect Of Carbon Black On The Mechanical Performances Of Magnetorheological Elastomers, Lin Chen

Articles

Several magnetorheological elastomer (MRE) samples, with different weight percentages of carbon black, were fabricated under a constant magnetic field. Their microstructures were observed by using an environmental scanning electron microscope (SEM), and their mechanical performance including magnetorheological (MR) effect, damping ratio and tensile strength were measured with a dynamic mechanical analyzer (DMA) system and an electronic tensile machine. The experimental results demonstrate that carbon black plays a significant role in improving the mechanical performance of MR elastomers. Besides the merits of high MR effect and good tensile strength, the damping ratio of such materials is much reduced. This is expected …

Microstructures And Viscoelastic Properties Of Anisotropic Magnetorheological Elastomers, Lin Chen

Articles

The microstructures and viscoelastic properties of anisotropic magnetorheological elastomers were investigated in this paper. The measurement results show that their mechanical properties are greatly dependent on the magnetic flux density applied in preparation. A finite-column model was proposed to describe the relations between the microstructures and the viscoelastic properties. The simulation results agree well with the experimental results.

Investigation On Magnetorheological Elastomers Based On Natural Rubber, Lin Chen

Articles

Magnetorheological Elastomers (MR Elastomers or MREs) are a kind of novel smart material, whose mechanical, electrical, magnetic properties are controllable under applied magnetic fields. They have attracted increasing attentions and broad application prospects. But conventional MREs are limited to wide applications because their MR effects and mechanical performances are not high enough. This paper aims to optimize the fabrication method and to fabricate good natural rubber based MREs with high modulus by investigating the influences of a variety of fabrication conditions on the MREs performances, such as matrix type, external magnetic flux density, and temperature, plasticizer and iron particles. Among …

Friction And Adhesion In Rigid Surface Indentation Of Nitrile Rubber, Stephen Jerrams

Articles

When a rigid body in the form of a plane strain indentor is forced into an elastomer, the asperities on the surface of the indentor are filled by the softer material. As depth of ingress increases, the rubber displaced into the indentor asperities exhibits stick-slip behaviour. The rubber adheres to the rigid body and if the depth of ingress is held at a maximum, the level of adhesion remains constant despite short-term load relaxation occurring in the rubber.

This text describes the influence of a range of factors on indentation forces and adhesion in rigid indentation of hydrogenated nitrile rubbers. …