Polymer and Organic Materials Commons^™

Material Selection And Testing For A Radiation Therapy Catheter, Philip James Wadlow

Master's Theses

Three different polymers (a high-density polymer and two other polymers) were tested for use as an x-ray catheter in a radiation therapy application. This report describes the testing of these three materials to determine which material is the best option for a long use catheter. Tests included tensile, simulated clinical life, and other tests. Some testing was performed using nitrogen and an industrial coolant. Testing revealed significant non-circularities for some catheters. With increasing pressure, the circularity of these catheters increased. The tensile tests were performed on samples with varying doses of radiation. Tensile testing showed significant decreases in ultimate tensile …

Improving The Mechanical Performance Of 3d Printed Parts Using Fused Filament Fabrication, Inderpreet Binning

Industrial and Manufacturing Engineering

The 3D printing industry has seen rapid growth in the last 10 years and has been called the next industrial revolution. There are several different processes used in 3D printing, but the most popular process is called Fused Filament Fabrication (FFF) or Fused Deposition Modeling (FDM). This is the process where (most commonly) plastic filament enters a nozzle, is heated to a semi-liquid state, and then deposited into a pattern to create a print. One major drawback to this process is that the prints are anisotropic. This means that the strength of the print varies with the orientation that it …

Solution Casting And Mechanical Testing Of Arabinan-Cellulose Nanocomposites, Kevin Su, Alina Lusebrink

Materials Engineering

The purpose of this work was to investigate methods to produce consistent, reliable, and testable thin films of arabinan-cellulose nanocomposites. Mechanical properties and composition of the Opuntia ficus-indica cactus spines served as motivation for this research. The high specific strength and stiffness, biodegradability, and sustainability of these spines inspired the creation of composites fabricated from the same materials found in cactus spines: arabinan and nanocrystalline cellulose (NCC). Arabinan serves as the matrix material and NCC as the reinforcement. To explore the feasibility of using a non-toxic solvent, different solution casting techniques with water as a solvent were investigated. Ultrasonication was …

Effect Of Metal Organic Framework Concentration On The Crystallization Of Pla-Al-Mof Composites, Eric Futak, Jeffrey Norton, Jessie O'Connell, Nestor Vazquez

Materials Engineering

Poly(lactic acid) (PLA), a well-known biopolymer, is lacking in barrier properties and toughness. The research goal of this project is to look at the crystallinity of PLA when combined with metal organic framework (MOF). It is speculated that MOF has an effect on PLA chain mobility, and therefore crystallinity. In this study, aluminum MOF was added to PLA in varying concentrations (0, 0.5, 1, 2, 5, 10, and 20 wt%) to observe the crystallinity of the composite. The resulting PLA-Al-MOF composite films were characterized using differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), and scanning electron …

Manufacturing And Characterization Of Poly (Lactic Acid)/Carbon Black Conductive Composites For Fdm Feedstock: An Exploratory Study, Dylan Fitz-Gerald, Justin Boothe

Materials Engineering

This exploratory study developed methods of manufacturing and characterizing the electrical properties of small batches of conductive composite feedstock for the Fused Deposition Modeling (FDM) manufacturing process, commonly known as 3D printing. We utilized a solution casting process of Poly(lactic acid) (PLA) (Grade 4043D, NatureWorks, LLC.) and Carbon Black (CB) (Vulcan® XC72, Cabot Corp.) in chloroform. The resulting composite precursor was cryogenically treated with liquid nitrogen and milled in a coffee grinder in order to achieve particles that could be fed into the extruder. Composite precursors were dried in a vacuum oven at an elevated temperature of 38°C. Filaments were …

Low-Cost Prosthetic Transfemoral Socket, Emelie Deans, Joshua Ledgerwood, Leah Moore, Shaina Jung, Kristen Temnyk

Mechanical Engineering

The goal of this senior project was to design and fabricate a low-cost adjustable prosthetic socket for above the knee amputees. This low-cost consideration was incorporated with the original intent to be used in Fiji, however, this changed to the Dominican Republic. It became clear that the need for an adjustable socket was more as a transitional socket. This transitional socket would be used for the first 6 -12 months upon amputation because this when the most amount of volume fluctuation occurs. The project sponsor, LIM Innovations, has already designed the Infinite Socket which contains four main functioning parts: baseplate, …

Design And Testing Of A Top Mask Projection Ceramic Stereolithography System For Ceramic Part Manufacturing, Dylan Robert De Caussin

Master's Theses

Ceramic manufacturing is an expensive process with long lead times between

the initial design and final manufactured part. This limits the use of ceramic as a viable material unless there is a large project budget or high production volume associated with the part. Ceramic stereolithography is an alternative to producing low cost parts through the mixing of a photo curable resin and ceramic particles. This is an additive manufacturing process in which each layer is built upon the previous to produce a green body that can be sintered for a fully dense ceramic part.

This thesis introduces a new approach …

Process Development For Compression Molding Of Hybrid Continuous And Chopped Carbon Fiber Prepreg For Production Of Functionally Graded Composite Structures, Corinne Marie Warnock

Master's Theses

Composite materials offer a high strength-to-weight ratio and directional load bearing capabilities. Compression molding of composite materials yields a superior surface finish and good dimensional stability between component lots with faster processing compared to traditional manufacturing methods. This experimental compression molding capability was developed for the ME composites lab using unidirectional carbon fiber prepreg composites. A direct comparison was drawn between autoclave and compression molding methods to validate compression molding as an alternative manufacturing method in that lab. A method of manufacturing chopped fiber from existing unidirectional prepreg materials was developed and evaluated using destructive testing methods. The results from …

Effect Of Heat Treatment On The Mechanical Properties In Natural Bamboo, Austin Levy, Mackenzie Kirkpatrick

Materials Engineering

Previous studies have shown that heat treatments have the ability to improve mechanical strength and stiffness in hardwood species. Compared to structural hardwoods, bamboo is a more sustainable and globally viable renewable resource. Therefore, Bambusoides vivax (timber bamboo) culms were fabricated into flat, rectangular cross-section samples with varying cellulose content to be heat treated and tested for mechanical properties. All samples were heat treated (HT) twice. The first HT was a normalization of all samples at 103 +/- 3 °C. The second HT was performed at various times and temperatures ranging from 130°C to 170°C for 0.5 to 3 hours. …

Minimizing Sheet Resistance Of Organic Photovoltaic Cell Top Contact Electrode Layer: Silver Nanowire Concentration Vs. Conductive Polymer Doping Concentration, Caitlyn Cook

Materials Engineering

The top contact electrode layers of nine organic photovoltaic cells were prepared with two varying factors: three Silver nanowire (AgNW) densities deposited on a conductive polymer doped with three concentrations. Silver’s low sheet resistance of 20-Ω/sq is hypothesized to lower the sheet resistance of the anode layer and thus enhance the overall efficiency of the cell. Four-point probe measurements indicated that increasing AgNW density in the top contact electrode layer of an organic photovoltaic cell significantly reduces sheet resistance from 52.2k-Ω/sq to 18.0 Ω/sq. Although an increase in doping concentration of the conductive polymer reduced sheet resistance in low AgNW …

Effect Of Time Delay Between Etching And Adhesive Bonding (“Outlife” Time) On Lap-Shear Strength Of Aluminum Alloys Using Environmentally-Friendly P2 Etch, Josh Barkhimer, Matthew Erich, Gokul Nair

Materials Engineering

Raytheon Company currently uses a Forest Products Laboratory (FPL) paste etchant for preparing aluminum surfaces for adhesive bonding, and FPL is a source of hazardous hexavalent chromium. The goal of this study was to evaluate a less-toxic P2 paste etchant as a possible replacement. Coupons of 2024-T3, 6061-T6, and 7075-T6 grades of aluminum alloy were solvent-degreased, abrasively cleaned, and etched at room temperature using P2 paste following a strict protocol adopted from Raytheon. Coupons were then left exposed to air for assigned time intervals (or “outlife” times) of 0, 1, 4, 8, 16, and 63 or 72 hours. The aluminum …

Molecular Dynamics Investigation Of The Arabinan-Cellulose Interface For Cellulose Nanocomposite Applications, Luke Thornley

Materials Engineering

Atom level computer simulations of the arabinan and cellulose interface were performed to better understand the mechanisms that give arabinan-cellulose composites (ArCCs) their strength with the goal to improve man-made ArCCs. The molecular dynamics (MD) software LAMMPS was used in conjunction with the ReaxFF/c force field to model the bond between cellulose and arabinan. A cellulose nanocrystal with dimensions 51 x 32 x 8 Å was minimized with various weight percent of water, 0%, 3%, 5%, 8%, 10%, and 12%. After the system was equilibrated for at least 100,000 femtoseconds, an arabinan molecule composed of 8 arabinose rings was added …

Effect Of Surfactant Architecture On Conformational Transitions Of Conjugated Polyelectrolytes, Greg A. Braggin

Master's Theses

Water soluble conjugated polyelectrolytes (CPEs), which fall under the category of conductive polymers, possess numerous advantages over other conductive materials for the fabrication of electronic devices. Namely, the processing of water soluble conjugated polyelectrolytes into thin film electronic devices is much less costly as compared to the processing of inorganic materials. Moreover, the handling of conjugated polyelectrolytes can be performed in a much more environmentally friendly manner than in the processing of other conjugated polymers because conjugated polyelectrolytes are water soluble, whereas other polymers will only dissolve in toxic organic solvents. The processing of electronic devices containing inorganic constituents such …

Self-Contained Breathing Apparatus For Firefighter With A Permanent Stoma, Jason Delgadillo, Aaron Wheeler, Zachary Wishbow

Biomedical Engineering

The purpose of this project was to create a unique SCBA (self-contained breathing apparatus) for a firefighter named Chris Gauer. This prototype consists of a SCBA headgear connected to a polycarbonate-formed stoma mask with a medical-grade sanitary silicone hose.

Interfacial Interactions Between Carbon Nanoparticles And Conjugated Polymers, Yanqi Luo

Master's Theses

Conjugated polymer based electronics, a type of flexible electronic devices, can be produced from solution by traditional printing and coating processes in a roll-to-roll format such as papers and graphic films. This shows great promise for the emerging energy generation and conversion. The device performance of polymer electronics is largely dependent of crystalline structures and morphology of photoactive layers. However, the solution crystallization kinetics of conjugated polymers in the presence of electron acceptor nanoparticles has not been fully understood yet. In this study, solution crystallization kinetics of poly (3-hexylthiophene) in the presence of carbon nanotubes and graphene oxide has been …

Synthesis And Characterization Of Cdse/Zns Core/Shell Quantum Dot Sensitized Pcpdtbt-P3ht:Pcbm Organic Photovoltaics, Buddy J. Bump

Master's Theses

Durable, cheap, and lightweight polymer based solar cells are needed, if simply to meet the demand for decentralized electrical power production in traditionally “off-grid” areas. Using a blend of Poly(3-hexylthiophene-2,5-diyl) (P3HT), Phenyl-C61-butyric acid methyl ester (PCBM), and the low band-gap polymer Poly[2,6-(4,4-bis-(2- ethylhexyl)-4H-cyclopenta [2,1-b;3,4-b′]dithiophene)-alt-4,7(2,1,3-benzothiadiazole)] (PCPDTBT), we have fabricated devices with a wide spectral response and 3% power conversion efficiency in AM 1.5 conditions; however, this thin film system exhibits only 0.43 optical density at 500 nm. To improve the performance of this polymer blend photovoltaic, we aim to increase absorption by adding CdSe(ZnS) core (shell) quantum dots. Four groups of …

Manufacture And Mechanical Testing Of Thin Film Composites Composed Of Poly-Lactic Acid And Nanocrystalline Cellulose, Catherine E. Mohan

Materials Engineering

Society’s overuse of petroleum-based plastic products has created a waste problem that is threatening environments around the world. New efforts have been made to find a suitable replacement derived from a renewable source. Poly-lactic acid has become one of the front-runners in this search. It is derived from starches found in potatoes, corn, and other grains. There are many factors that make Poly-lactic acid-based polymers a suitable replacement for petroleum-based ones, but it still suffers from low mechanical strength due to low crystallinity percentages. Doping the polymer with nanocrystalline cellulose provides more nucleation sites for the crystallization of the polymer …

Mechanical Behavior Of Compression Molded Polyethylene Terephthalate, Daniel Cole Greinke, Paul Jackson Mcewan, Dan Tran

Materials Engineering

The purpose of this project was to investigate the effects of time, temperature, and pressure on the tensile strength and elastic modulus of recycled PET. Compression molding trials were performed on shredded PET bottles to produce tensile test specimens conforming to ASTM D638-03. Aluminum molds containing the PET were mechanically fastened together at the desired pressure and heated in an electric oven. The resulting specimens were subjected to tensile testing for analysis. This screening experiment failed to generate any statistically significant data concerning the factors of interest. These preliminary results may be used to design a more systematic follow-up study.

Prediction Of Tribological Behavior Of Candidate Materials For Rotor Seals, John W. Franzino, Will F. Michul

Materials Engineering

To reduce high costs associated with manufacturing and testing materials for rotor seals, a procedure needs to be developed to quickly and accurately test candidate materials as they are released. The test should reduce the amount of fabrication required and model working conditions in order to accurately assess the tribological behavior of candidate materials. A possible solution was examined that utilized a rig meant to model operational stresses and wear. Compression modulus data was then taken in order to quantify the accumulation of damage due to microcracking, the primary mode of failure, through a damage index parameter. Testing results concluded …

Characterization Of A Thin Film Composite Membrane: Fluorinated Copolymer In A Carbon Nanotube Matrix, Eric P. Bonaventure, Michael A. Brew, Cynthia R. Shannon

Materials Engineering

IDEX Health and Science has created a thin-film composite membrane consisting of a carbon nanotube matrix impregnated with a fluorinated copolymer called Teflon® AF 2400. This membrane is being studied for use in degassing chambers of analytical instruments such as a High Pressure Liquid Chromatography (HPLC) degassing modules. The level of impregnation of the Teflon® in the carbon matrix affects the diffusion properties which are crucial for the performance of the membrane. Scanning Electron Microscopy (SEM) characterization techniques were used to measure the outer Teflon® and the inner carbon matrix layer thickness. The outer Teflon® and inner carbon matrix layer …

Lunalight - Bringing Light To The Expanding World, Gabriela M. Igel, Daniel J. Patrick, Kimberley M. Smith

Materials Engineering

The LunaLight, a solar rechargeable light and cell phone charger, addresses the lack of access to electricity faced by 1.4 billion of the world’s population (International Finance Corporation). The LunaTech team has developed a product that is bright, simple, compact, versatile and competitive with existing products. Through a partnership with the non-profit organization One Million Lights, LunaTech has improved a previous team’s design to address user feedback, concerns of durability, and manufacturability.

The LunaLight design includes a 5 component plastic housing held together by 4 screws, a surface mounted PCB, a lithium-ion (Li-Ion) battery, one high-brightness LED, a solar panel, …

The Fabrication & Characterization Of An Electrokinetic Microfluidic Pump From Su-8, A Negative Epoxy-Based Photoresist, Nash Anderson

Master's Theses

Microfluidics refers to manipulation, precise control, and behavior of fluids at the micro and nanoliter scales. It has entered the realm of science as a way to precisely measure or mix small amounts of fluid to perform highly controlled reactions. Glass and polydimethylsiloxane (PDMS) are common materials used to create microfluidic devices; however, glass is difficult to process and PDMS is relatively hydrophobic. In this study, SU-8, an epoxy based (negative) photoresist was used to create various electrokinetic microfluidic chips. SU-8 is commonly used in microelectromechanical design. Spin coating of various SU-8 formulations allows for 1 μm to 100 μm …

Evaluation Of Corrosion Properties Of Proprietary Metal Alloy Stents For In-Vivo Use, Michael David Bremner

Materials Engineering

To assess corrosion rates of metal alloy bio-absorbable stents an experimental set-up was designed to mimic the coronary artery environment. The artery was modeled using 4mm diameter Tecoflex tubing and the metal alloy stents were inserted into the tubing using a catheter. As is the case in cardiac surgery, the catheter with the stent and a microballoon were maneuvered to the desired position. The microballoon was then slowly inflated to expand the stent and compress it against the tubing walls. The catheter and microballoon were then withdrawn. A circulating pump system was set up to cycle fetal bovine serum (FBS) …

Preparation Of A Polylactic Acid With Hydroxyapatite Reinforcement Composite, Odessa N. Quezon

Materials Engineering

Biodegradable polymers are a prime material choice for temporary biomedical devices due to its ability to degrade into non-toxic products for their use in vivo. However, polylactic acid (PLA) by itself lacks the sufficient strength and stiffness to permit their use as its properties begin to decrease as the polymer degrades. To improve the polymer’s mechanical properties, hydroxyapatite (HA) will be added to the PLA solution to act as reinforcement. The chemical property, glass transition temperature of a polymer, also plays a key role in the mechanical properties of the polymer. PLA’s glass temperature is 130⁰F. A polymer that …

Strength Testing And Material Characterization Of Cactus Spines, Mary Cooper, Jeff Goldstein, Thomas Tarlton

Materials Engineering

Twelve different species of cactus spines from 6 different genera were collected from living specimens and maintained in a dry storage environment. Spines from each species underwent 3-point bend testing, XRD testing, and SEM imaging. XRD analysis was used to verify the presence of cellulose whisker like nanocrystals and to calculate the percent crystallinity of each spine. SEM images were captured of fracture surfaces at viewing angles of 90° and 45° relative to the fracture surface, with magnifications ranging between 150x and 4,000x. A total of six spines from each species were tested in three point bending using a high-resolution …

Design And Construction Of A Simulated Evaporative Heat Exchanger For Testing The Mitigation Effects Of Pipe Coatings On Mineral Scale Deposition, Taylor J. Anderson

Materials Engineering

The thermal efficiency of evaporative heat exchangers is diminishing due to mineral scale buildup on heat exchanger surfaces. A simulated evaporative heat exchanger was designed and constructed for testing the mitigation effects of polymer coatings on mineral scale deposition rates. The heat exchanger was designed to cool hot mud at 200°F using a cooling water supply with a calcium concentration of 1000 ppm. The system was constructed using 1.5-inch diameter polypropylene piping, a DIG Corporation drip irrigation system, a TotalPond 530 GPH pond pump, an Omega CSI32K miniature benchtop controller, Omega FWH321-020 high temperature heater tape, and fifteen copper pipe …

Analyzing The Acoustical Properties Of Alternative Materials In Guitar Soundboards To Reduce Deforestation, Chris Dunn

Materials Engineering

To mitigate the effects of deforestation, man-made alternative materials were analyzed and tested for potential use in the soundboards of acoustic guitars. The materials evaluated included 0.06 in. foamed polycarbonate, 0.12 in. single-ply honeycomb fiberglass, and 0.04 in. epoxy fiberglass. The properties of Sitka spruce, the most common tonewood, were used as a benchmark. The Young’s modulus to density ratio found in Sitka spruce is relatively high, making its properties ideal for soundboard applications. Both Young’s modulus and density were necessary to calculate the acoustic constant of each material that was tested. The samples were subject to the impact of …

Comparison Of Polyurethane And Polysiloxane Coating Systems In Marine Environments, Jake Jarman, Jessica Salvatin

Materials Engineering

This project investigates the performance benefits of polysiloxane and polyurethane coating systems for corrosion protection in marine environments. PPG Industries Amercoat 450H and International Paint Interthane 990HS were the polyurethane topcoats tested. PPG Industries Ameron PSX 700 (New Blend) and International Paint Interfine 878 were the polysiloxane topcoats tested. Each coating was sprayed onto carbon steel panels that were prepared through hand blasting with glass beads. Scribed and unscribed panels were tested in a salt fog chamber for 1,200 hours according to ASTM Standard B0117-11 and in a UV/Humidifier for 1,650 hours according to ASTM Standard D4587-11. Panels were tested …

Low Velocity Impact Tower Feasibility, Setup, And Impact Testing Of Carbon Fiber Reinforced Epoxy Thermoset And Peek Thermoplastic Matrix Composites, Brent Plehn

Materials Engineering

A low velocity impact tower was donated to Cal Poly's Materials Engineering Department along with four fiber reinforced polymer matrix composites. The tower was set up in building 192 in the Mechanical Testing Laboratory. Improvements were made to the tower including adding velocity detection capabilities, making loose hardware inclusive, adding an extra tower arm for better consistency, adding a double jawed clamp for faster testing, and rerouting the tower's compressed air system to improve performance. A standard operating procedure was drafted, tested, and redrafted for impact testing composite panels. The four composite panels consisted of two quasi-isotropic 16 ply AS-1 …

Surfactant Formulations For Water-Based Processing Of A Polythiophene Derivative, Cameron Dean Danesh

Master's Theses

Conjugated polymers are semiconducting materials that are currently being researched for numerous applications from chemical and biological sensors to electronic devices, including photovoltaics and transistors. Much of the novel research on conjugated polymers is performed in academic settings, where scientists are working to prepare conjugated polymers for commercially viable applications. By offering numerous advantages, inherent in macromolecular materials, conjugated polymers may hold the key to cheap and environmentally friendly manufacturing of future electronic devices. Mechanical flexibility, and solvent-based coating processes are two commonly cited advantages. Transitions in the backbone conformation of polythiophenes (PT) in organic solvents have been widely observed …