Polymer and Organic Materials Commons^™

Temperature Dependent Surface Reconstruction Of Freely Suspended Films Of 4-N-Heptyloxybenzylidene-4-N-Heptylaniline, Daniel E. Martinez Zambrano

Lawrence University Honors Projects

Surfaces of freely suspended thick films of 4-n-heptyloxybenzylidene-4-n-heptylaniline (7O.7) in the crystalline-B phase have been imaged using non-contact mode atomic force microscopy. Steps are observed on the surface of the film with a height of 3.0 +/- 0.1 nm corresponding to the upright molecular length of 7O.7. In addition, we find that the step width varies with temperature between 56 and 59 degrees C. The steps are many times wider than the molecular length, suggesting that the steps are not on the surface but instead originate from edge dislocations in the interior. Using a strain model for liquid crystalline layers …

Effect Of Surfactant Architecture On Conformational Transitions Of Conjugated Polyelectrolytes, Greg A. Braggin

Master's Theses

Water soluble conjugated polyelectrolytes (CPEs), which fall under the category of conductive polymers, possess numerous advantages over other conductive materials for the fabrication of electronic devices. Namely, the processing of water soluble conjugated polyelectrolytes into thin film electronic devices is much less costly as compared to the processing of inorganic materials. Moreover, the handling of conjugated polyelectrolytes can be performed in a much more environmentally friendly manner than in the processing of other conjugated polymers because conjugated polyelectrolytes are water soluble, whereas other polymers will only dissolve in toxic organic solvents. The processing of electronic devices containing inorganic constituents such …

Feasibility Study: The Evaluation Of Polymer Coatings To Prevent Weathering Of Weak Rocks, Lauren Distler

Senior Honors Projects, 2010-2019

The weathering and erosion of weak rocks along roadways can cause dangerous and potentially fatal rockfalls.   Various slope stabilization methods exist, but each presents a set of challenges and trade-offs.   The focus of the project is to understand the feasibility of utilizing of a polymerbased slope stabilization technique. Rock samples were collected along US Route 33 in Virginia and West Virginia, and preliminary tests were conducted to evaluate the absorption of water (% mass) and durability. The study evaluates three polymer options in regard to the following criteria: adhesion to rock, layer thickness, semi-permeability, insolubility, and non-toxicity. The polymer selection …

Utilization Of Aqueous Raft Prepared Copolymers To Improve Anticancer Drug Efficacy, Andrew Christopher Holley

Dissertations

The advent of controlled radical polymerization (CRP) techniques, along with advancements in facile conjugation chemistry, now allow synthetic tailoring of precise, polymeric architectures necessary for drug/gene delivery. Reversible addition- fragmentation chain transfer (RAFT) polymerization and its aqueous counterpart (aRAFT) afford quantitative control over key synthetic parameters including block length, microstructure, and placement of structo-pendent and structo-terminal functionality for conjugation of active agents and targeting moieties. The relevance of water-soluble and amphiphilic (co)polymers synthesized by RAFT for in vitro delivery of therapeutics in biological fluids is an especially attractive feature. In many cases, polymerization, binding, conjugation, …

The Development Of A Laminated Copolyester Electric Guitar, Addison S. Karnes

Electronic Theses and Dissertations

This thesis is an investigation of the fabrication and assembly methodologies employed in the development of a proof-of-principle prototype electric guitar composed of laminated copolyester. The objective of the project was to develop the processes and procedures to create an optimized physical and visual bond between layers to minimize vibratory dissipation, thus maximizing sustain. A high speed CNC router, abrasive waterjet, laser engraver-cutter, as well as various manual fabrication and assembly methods were investigated in the construction of the guitar prototypes. The lamination processes explored include low-temperature, heat-assisted pressure bonding, solvent and chemical welding, and contact adhesives. The project concluded …

A Soft Condensed Matter Approach Towards Mathematical Modelling Of Mass Transport And Swelling In Food Grains, Michael Chapwanya, N. Misra

Articles

Soft condensed matter (SCM) physics has recently gained importance for a large class of engineering materials. The treatment of food materials from a soft matter perspective, however, is only at the surface and is gaining importance for understanding the complex phenomena and structure of foods. In this work, we present a theoretical treatment of navy beans from a SCM perspective to describe the hydration kinetics. We solve the transport equations within a porous matrix and employ the Flory–Huggin’s equation for polymer–solvent mixture to balance the osmotic pressure. The swelling of the legume seed is modelled as a moving boundary with …

Study Of The Structure-Property Relationships That Determine The Effects Of Latexes And Starch Containing Latex Emulsions On The Performance Of The Barrier Coatings (Sub-Coat) For Paper, Joanna Marie Monfils

Master's Theses

The history of carbonless paper dates back to the 1940s. Before this, a carbon copy sheet was needed between sheets of paper to be able to produce one or more copies simultaneously during writing. The pressure from a pen or typewriter would help deposit the ink of the carbon paper onto the blank sheet of paper under the original written sheet to create a “carbon copy.” This method did however, have its disadvantages. Not only did it produce a limited number of copies, but it was also a messy process. So came the creative process of using microencapsulated dyes to …

Electrospinning Applications Air Filtration And Superhydrophobic Materials, Negar Ghochaghi, Adetoun Taiwo

Graduate Research Posters

Electrospinning is a widely applicable technique that generates non-woven fibers in the micro and nano range. In this project two of its applications are highlighted namely filtration media and enhancement of wettability. The first project demonstrates that electrospinning can be used to produce new fiber filtration media with controlled microstructure. The bimodal and unimodal orthogonal and random filters were made and characterized against their filtration efficiency and pressure drop. Figure of Merit (FOM) was also calculated and discussed. It is shown that the FOM increases when the electrospun fibers are arranged into alternating layers of aligned course and fine fibers. …

Addressing Public Health Risks Of Persistent Pollutants Through Nutritional Modulation And Biomimetic Nanocomposite Remediation Platforms, Bradley J. Newsome

Theses and Dissertations--Chemistry

Due to their relative chemical stability and ubiquity in the environment, chlorinated organic contaminants such as polychlorinated biphenyls (PCBs) pose significant health risks and enduring remediation challenges. Engineered nanoparticles (NPs) provide a novel platform for sensing/remediation of these toxicants, in addition to the growing use of NPs in many industrial and biomedical applications, but there remains concern for their potential long-term health effects. Research highlighted herein also represents a transdisciplinary approach to address human health challenges associated with exposure to PCBs and NPs. The objectives of this dissertation research are two-fold, 1) to develop effective methods for capture/sensing and remediation …

Next Generation Crystal Viewing Tool, Zach Schaffter, Gerhard Klimeck

The Summer Undergraduate Research Fellowship (SURF) Symposium

The science and engineering community is limited when it comes to crystal viewing software tools. Each tool lacks in a different area such as customization of structures or visual output. Crystal Viewer 2.0 was created to have all of these features in one program. This one tool simulates virtually any crystal structure with any possible material. The vtkvis widget offers users advanced visual options not seen in any other crystal viewing software. In addition, the powerful engine behind Crystal Viewer 2.0, nanoelectronic modeling 5 or (NEMO5), performs intensive atomic calculations depending on user input. A graphical user interface, or GUI, …

Applied Analysis Of Ionic Polymer Metal-Composite Actuators, Siul Ruiz, Benjamin Mead, Woosoon Yim

College of Engineering: Graduate Celebration Programs

• IPMC is a type of smart material called an electroactive polymer
• Consists of an ionic polymer such as Nafion or Flemion and a conducive metal such as platinum or gold
• COMSOL multi-physics simulations accurately model the experimental displacement results
• Optimization performed using the multi-physics model to find the maximum deflection, force, and twisting
• Using the closed loop control system accurate IPMC tip location can be achieved
• This control system has been extended to function using a computer mouse as an input

Pulse Sharpening Effects Of Thin Film Ferroelectric Transmission Lines, Robert J. Sleezer

Graduate Theses and Dissertations

Advances in material science have resulted in the development of electrically nonlinear high dielectric thin film ferroelectrics, which have led to new opportunities for the creation of novel devices. This dissertation investigated one such device: a low voltage nonlinear transmission line (NLTL). A finite element simulation of ferroelectric transmission lines showed that NLTLs are capable of creating shockwaves. Additionally, if the losses are kept sufficiently low, it was shown that voltage gain should be possible. Furthermore, a method of accounting for material dispersion was developed. Results from simulations including material dispersion showed that temporal solitons might be possible from a …

P3ht:Pcpdtbt:Pcbm Multi- Polymer Single Layer Solar Cells, Ted Andreas

Physics

OPV efficiencies are limited by their narrow absorption; rather than using tandem architecture to overcome this obstacle, our group combined P3HT and PCPDTBT into a single layer BHJ solar cell that achieved 2.0% PCE. This is 33% higher than the pure P3HT control from this group, proving that multi-polymer solar cells have the potential to outperform their single-polymer components.

Semiconductor Nanocrystals: From Quantum Dots To Quantum Disks, Zheng Li

Graduate Theses and Dissertations

The bottom-up colloidal synthesis opened up the possibility of finely tuning and tailoring the semiconductor nanocrystals. Numerous recipes were developed for the preparation of colloidal semiconductor nanocrystals, especially the traditional quantum dots. However, due to the lack of thorough understanding to those systems, the synthesis chemistry is still on the empirical level. CdS quantum dots synthesis in non-coordinating solvent were taken as a model system to investigate its molecular mechanism and formation process, ODE was identified as the reducing agent for the preparation of CdS nanocrystals, non-injection and low-temperature synthesis methods developed. In this model system, we not only proved …

Blunt Impact Performance Evaluation Of Helmet Lining Systems For Military And Recreational Use, Jaclyn Siniora, Ryan Taylor, Darren Suey

Industrial Technology and Packaging

With the increasing problem in collegiate athletes experiencing injuries to the brain, different helmet liners where put to the test to see which liner provided athletes the greatest protection under specific conditions.

This senior project evaluates five different liners in football helmets. Each of the helmet liners were tested at three different temperatures: hot, cold, and ambient. Each helmet had seven different impact locations which were put to the test. The project was designed to be used to test ACH military combat liners as well. Due to shipping bottle necks the ACH combat liners have been left to future Cal …

Multipolymer Interactions In Bulk Heterojunction Photovoltaic Devices, Grant Olson

Physics

Multipolymer photovoltaics, single layer devices made up of multiple photoactive polymers, can create organic photovoltaics (OPVs) with a wider spectral response than single polymer systems without the difficult fabrication of a tandem. Our group has successfully created multipolymer solar devices with 2% power conversion efficiency. We have analyzed the optical and electrical properties of these devices, and found that it may be possible for polymers to assist each other with charge extraction, though combining polymers disrupts single polymer crystallinity.

Active Response Of Polymer Materials From External Stimuli – Solvents And Light; Grafting Reactions On Perovskite Layers, Jianxia Zhang

LSU New Orleans Theses and Dissertations

The active response of a series of polymeric materials was investigated. Both solvent activated and light activated thin films and wire systems show dynamic behaviors when exposed to different stimuli.

Solvent mediated fluxional behavior of polymer thin films involved extensive, rapid curling both on infusion and evaporation of good solvents. These films can be either lab-fabricated ones or commercial ones, and the curling behavior can be as fast as seconds. Conditions including polymer materials, chosen solvents, and film geometry can affect the behavior.

Methods that allowed for the creation and retention of distorted wire structures were also developed; the asymmetric …

Cross-Linked Pdms Expansion Due To Submersion In Liquid And Supercritical Co2, Teng Yang

Graduate Theses and Dissertations

Characterization of micro/nano-copper particles impregnated Polydimethylsiloxane (PDMS) submersed in supercritical carbon dioxide (scCO2) was studied. The purpose of this investigation was to advance micro-corrosion sensor technology utilizing PDMS and micro-metal particle composite as the sensing element currently under-development. One of the key challenges encountered was the removal of the native oxides inherently existing on the metal particles. Numerous techniques were experimented with to counter this problem at the UA Engineered Micro/Nano Systems Laboratory (EMNSL), with swell-based protocols being identified as the most promising solution. In terms of compatibility to Micro-electro-mechanical Systems (MEMS) fabrication, CO2 is often used in the release …

Direct Contact Pyrolysis Of Hydrocarbons: A Source Of Hydrogen And Interesting Carbon Formations, Peter G. Faught

UNLV Theses, Dissertations, Professional Papers, and Capstones

The work detailed in this document looks at a novel liquid metal supported catalytic system for the generation of hydrogen by decomposition of ethanol through direct contact pyrolysis. The hydrogen is produced at relatively low temperatures (500-600°C) and has carbon and water as co-products. It should be noted that CO is not observed as a product at these low temperatures. This is to be contrasted with the hydrogen produced at higher temperature from ethanol which does contain carbon monoxide. The presence of carbon monoxide in hydrogen complicates fuel cell operation and catalytic chemical processes. Thus, the lack of CO in …

Morphology Changes In Pcpdtbt:Pcbm And P3ht:Pcpdtbt:Pcbm And Its Effect On Polymer Solar Cell Performance, Galen David Cauble

Physics

Polymer solar cell morphology is sensitive to both heat and time. By thermally annealing polymer solar cells the morphology of the devices can be altered causing immediate changes in device performance. Blending PCPDTBT:PCBM with P3HT:PCPDTBT combines the absorption characteristics of each to create a more even absorption spectrum. Subjecting PCPDTBT:PCBM, and P3HT:PCPDTBT:PCBM polymer solar cells to thermal annealing as well as recording device performance through time has shown that P3HT:PCPDTBT:PCBM devices react positively to thermal annealing (increasing from 0.8% to 1.4%) while PCPDTBT:PCBM devices have varied reactions. Furthermore, the P3HT:PCPDTBT:PCBM devices have achieved efficiencies of 1.6% in AM 1.5 compared …

Improving The Efficiency Of Organic Solar Cells By Varying The Material Concentration In The Photoactive Layer, Kevin Anthony Latimer

Electrical & Computer Engineering Theses & Dissertations

Polymer-fullerene bulk heterojunction solar cells have been a rapidly improving technology over the past decade. To further improve the relatively low energy conversion efficiencies of these solar cells, several modifications need to be made to the overall device structure. Emerging technologies include cells that are fabricated with interfacial layers to facilitate charge transport, and tandem structures are being introduced to harness the absorption spectrum of polymers with varying bandgap energies.

When new structures are implemented, each layer of the cell must be optimized in order for the entire device to function efficiently. The most volatile layer of these devices is …

Artificial Muscle Project: Process Development Of Polydimethyl Siloxane Thin Films For Use In Dielectric Electroactive Polymer Artificial Muscle Actuators, Vincent J. Gayotin, Richard W. Morrison, Paul A. Preisser

Materials Engineering

An artificial muscle design was created founded on the principles of a dielectric electroactive polymer (DEAP), which is fundamentally similar to a capacitor. A polydimethyl siloxane (PDMS)-based elastomer, Sylgard 184 from Dow Corning, was chosen for the design and spun coat onto polystyrene (PS) Petri dishes at varying speeds to create a thin film, using speeds of 2000 rpm, 3000 rpm, 4000 rpm, 5000 rpm, and 6000 rpm. The film thicknesses were measured optically through use of a microscope with coupled computer imaging software to generate a characteristic curve of film thickness to spin speed, achieving a minimum film thickness …

A Least Squares Closure Approximation For Liquid Crystalline Polymers, Traci Ann Sievenpiper

Mathematics & Statistics Theses & Dissertations

An introduction to existing closure schemes for the Doi-Hess kinetic theory of liquid crystalline polymers is provided. A new closure scheme is devised based on a least squares fit of a linear combination of the Doi, Tsuji-Rey, Hinch-Leal I, and Hinch-Leal II closure schemes. The orientation tensor and rate-of-strain tensor are fit separately using data generated from the kinetic solution of the Smoluchowski equation. The known behavior of the kinetic solution and existing closure schemes at equilibrium is compared with that of the new closure scheme. The performance of the proposed closure scheme in simple shear flow for a variety …

An Analytical Model Of Nanometer Scale Viscoelastic Properties Of Polymer Surfaces Measured Using An Atomic Force Microscope, Jacob B. Goldberg

Theses and Dissertations

The United States Air Force and the Department of Defense is increasingly interested in nanomaterials. To study these materials, one needs to measure the mechanics of materials on the nanoscale. Over the past few decades the atomic force microscope (AFM) has been used in various methods to establish local surface properties at the nanoscale. In particular, surface elasticity measurements are crucial to understanding nanoscale surface properties. Problems arise, however, when measuring soft surfaces such as polymers and biological specimens, because these materials have a more complex viscoelastic response. This research focuses on modeling an AFM dynamic nanoindentation experiment intended to …

Creep In Photovoltaic Modules: Examining The Stability Of Polymeric Materials And Components, David C. Miller, Michael D. Kempe, Stephen H. Glick, Sarah R. Kurtz

Publications (E)

Interest in renewable energy has motivated the implementation of new polymeric materials in photovoltaic modules. Some of these are non-cross-linked thermoplastics, in which there is a potential for new behaviors to occur, including phase transformation and visco-elastic flow. Differential scanning calorimetry and rheometry data were obtained and then combined with existing site-specific time-temperature information in a theoretical analysis to estimate the displacement expected to occur during module service life. The analysis identified that, depending on the installation location, module configuration and/or mounting configuration, some of the thermoplastics are expected to undergo unacceptable physical displacement. While the examples here focus on …

Optimization Of P3ht-Pcbm Polymer Solar Cells Through Device Simulation And Manufacturing, James Boom

Computer Engineering

Given a good model and implementation of that model, computer simulation can be used to reduce the time and material costs of research. To this end I worked with other students to manufacture, test and simulate the single layer P3HT-PCBM solar cell. Using the data collected from this project, future work can then be done with the project's simulator to further optimize these types of solar cell devices.

Preparation Of Styrene Acrylic Copolymer Toner Resin By Solution Polymerization., Neo Su Siang

Student Works (2010-2019)

This project has investigated solution polymerization to produce toner resins. There are three stages: (i) synthesis of low molecular weight styrene acrylic copolymer; (ii) synthesis of high molecular weight styrene acrylic copolymer; (iii) mixing high and low molecular weight copolymers. Gel Permeation Chromatography (GPC) was used to study molecular weight distributions, Melt Flow Index (MFI) Instrument to study the flowability of resin, Differential Scanning Calorimetry (DSC) to study the thermal properties of resin, and acid number to quantitate the amount of acidic group in the resin. A comparison of properties between the experimental samples, patent’s claims, and commercial resins had …

Palm Oil-Based Polyester Binder For Making Fiberboards., Wong Yew Chuan

Student Works (2010-2019)

Palm kernel oil was used as a raw material for the synthesis of polyester polyol.The palm oil based polyester polyol was synthesized using glycerol, phthalic anhydride and fumaric acid. Palm oil based polyester polyol combines with methylene diphenyl diisocyanate (MDI) to form the polyurethane binder. The fibers are derived from empty fruit bunch (EFB) of the palm tree and have the acceptable mechanical properties. In this project, palm fibers were converted into palm fiberboards by using polyurethane (PU) binder under specified pressure and temperature. The binder to fiber ratio was varied from 10% to 30 % by dried weight of …

Characteristics Of Proton Conducting Pva-Chitosan Polymer Blend Electrolytes., Mohd Fakhrul Zamani Abdul Kadir

Student Works (2010-2019)

The main focus of this present work is to build a good conducting solid polymer electrolyte (SPE) based on chitosan and poly(vinyl alcohol)(PVA) blend. Solution cast technique has been employed to produce sample films in this work. From the scanning electron micrographs (SEM) the surface morphology of the blend containing 40 wt.% chitosan and 60 wt.% PVA (C4P6) is homogenous and miscible in one and another. The C4P6 film is the most amorphous and is the best candidate for the polymer host in the electrolyte systems studied in the present work. Ammonium Nitrate (NH4NO3) is the doping salt that provides …

Thermo-Electrical And Mechanical Studies On Polymer-Organically Modified Montmorillonite Composite., Norhana Abdul Halim

Student Works (2010-2019)

The field of polymer-nanoclay composite has attracted a lot of attention in materials studies due to the dramatic improvement on polymers characteristics. For example mechanical and thermal properties, chemical resistance as well as the reduced gas permeability. However, structural changes and the mechanisms that may contribute to these improvements are not fully understood. In this work, the study on polymer nanoclay composite concentrates on the effects of OMON inclusion within different polymer matrix systems. The matrixes are a series of natural rubbers (Standard Malaysia Rubber – Latex grade (SMRL); Deproteinized Natural Rubber (DPNR) and Epoxidized Natural Rubber (ENR-50)), plasticized Polyvinyl …