Polymer and Organic Materials Commons^™

Materials Education And Research In Art And Design: A New Role For Libraries (Website), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

No abstract provided.

Materials Collection Creation And Administration: A New Role For Libraries (White Paper), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

The Problem/Opportunity: To define, identify, and guide design-based materials collections in academic settings and foster community among those with existing collections and/or those considering creating and supporting one.

Contents and topics:

1. What is a materials collection?
2. Why have a materials collection?
3. Acquisition strategies
4. Organizational approaches
5. Programming possibilities
6. Symposium summary
7. Resources

Design And Construction Of A Simulated Evaporative Heat Exchanger For Testing The Mitigation Effects Of Pipe Coatings On Mineral Scale Deposition, Taylor J. Anderson

Materials Engineering

The thermal efficiency of evaporative heat exchangers is diminishing due to mineral scale buildup on heat exchanger surfaces. A simulated evaporative heat exchanger was designed and constructed for testing the mitigation effects of polymer coatings on mineral scale deposition rates. The heat exchanger was designed to cool hot mud at 200°F using a cooling water supply with a calcium concentration of 1000 ppm. The system was constructed using 1.5-inch diameter polypropylene piping, a DIG Corporation drip irrigation system, a TotalPond 530 GPH pond pump, an Omega CSI32K miniature benchtop controller, Omega FWH321-020 high temperature heater tape, and fifteen copper pipe …

Low Velocity Impact Tower Feasibility, Setup, And Impact Testing Of Carbon Fiber Reinforced Epoxy Thermoset And Peek Thermoplastic Matrix Composites, Brent Plehn

Materials Engineering

A low velocity impact tower was donated to Cal Poly's Materials Engineering Department along with four fiber reinforced polymer matrix composites. The tower was set up in building 192 in the Mechanical Testing Laboratory. Improvements were made to the tower including adding velocity detection capabilities, making loose hardware inclusive, adding an extra tower arm for better consistency, adding a double jawed clamp for faster testing, and rerouting the tower's compressed air system to improve performance. A standard operating procedure was drafted, tested, and redrafted for impact testing composite panels. The four composite panels consisted of two quasi-isotropic 16 ply AS-1 …

Study Of An Alternative Process For Oxidizing Vapor Grown Carbon Nanofibers Using Electron Beam Accelerators, Maria Cecília Evora, Donald A. Klosterman, Khalid Lafdi, Lingchuan Li, L.G.A. Silva

Chemical and Materials Engineering Faculty Publications

The use of a high-energy electron beam was explored in this study as an alternative technique for oxidizing vapor grown carbon nanofiber surfaces. The radiation exposures were carried out at three different electron beam facilities with beam energies of 1.5, 3.0 and 4.5 MeV and radiation doses ranging from 1000 to 3500 kGy. XPS analysis showed that oxygen was readily incorporated on the surface: the ratio O1s/C1s increased approximately by a factor of 4 when the carbon nanofibers were irradiated at 3500 kGy. The oxidized nanofibers exhibited better dispersion in a water/methanol solution (50% v/v) than as-received nanofibers. Raman spectroscopy …

Infrared Optical Properties Of Amorphous And Nanocrystalline Ta2o5 Thin Films, Trevor J. Bright, J. I. Watjen, Zhuomin Zhang, Christopher Muratore, Andrey A. Voevodin, D. I. Koukis, David B. Tanner, Daniel J. Arenas

Chemical and Materials Engineering Faculty Publications

The optical constants of tantalum pentoxide (Ta 2O5) are determined in a broad spectral region from the visible to the far infrared. Ta 2O5 films of various thicknesses from approximately 170 to 1600 nm aredeposited using reactive magnetron sputtering on Si substrates. X-ray diffraction shows that the as-deposited films are amorphous, and annealing in air at 800 °C results in the formation of nanocrystallineTa 2O5. Ellipsometry is used to obtain the dispersion in the visible and near-infrared. Two Fourier-transform infrared spectrometers are used to measure the transmittance and reflectance at wavelengths from 1 to 1000 μm. The surface topography and …

Cross-Plane Thermal Properties Of Transition Metal Dichalcogenides, Christopher Muratore, Vikas Varshney, Jaime J. Gengler, Jianjun Hu, John E. Bultman, Timothy M. Smith, Patrick J. Shamberger, Bo Qiu, Xiulin Ruan, Ajit K. Roy, Andrey A. Voevodin

Chemical and Materials Engineering Faculty Publications

In this work, we explore the thermal properties of hexagonal transition metal dichalcogenide compounds with different average atomic masses but equivalent microstructures. Thermal conductivity values of sputtered thin films were compared to bulk crystals. The comparison revealed a >10 fold reduction in thin film thermal conductivity. Structural analysis of the films revealed a turbostratic structure with domain sizes on the order of 5–10 nm. Estimates of phonon scattering lengths at domain boundaries based on computationally derived group velocities were consistent with the observed film microstructure, and accounted for the reduction in thermal conductivity compared to values for bulk crystals.

Tannic Acid Coated Gold Nanorods Demonstrate A Distinctive Form Of Endosomal Uptake And Unique Distribution Within Cells, Emily A. Untener, Kristen K. Comfort, Elizabeth I. Maurer, Christin M. Grabinski, Donald A. Comfort, Saber M. Hussain

Chemical and Materials Engineering Faculty Publications

One of the primary challenges associated with nanoparticle-dependent biological applications is that endosomal entrapment in a physiological environment severely limits the desired targeting and functionality of the nanoconstructs. This study sought to overcome that challenge through a systematic approach of gold nanorod (GNR) functionalization: evaluating the influence of both aspect ratio and surface chemistry on targeted cellular internalization rates and preservation of particle integrity. Owing to their unique spectral properties and enhanced surface area, GNRs possess great potential for the advancement of nanobased delivery and imaging applications. However, their ability for efficient intracellular delivery while maintaining their specific physiochemical parameters …

Atomistic Simulations Of Defect Nucleation And Intralayer Fracture In Molybdenum Disulphide During Nanoindentation, James A. Stewart

Graduate Theses and Dissertations

Molybdenum disulphide (MoS2) is a layered, hexagonal crystal that has a very low coefficient of friction. Due to this low coefficient of friction, MoS2 has become a well-known solid lubricant and liquid lubricant additive. As such, nanoparticles of MoS2 have been proposed as an additive to traditional liquid lubricants to provide frictional properties that are sensitive to different temperature and pressure regimes. However, to properly design these MoS2 nanoparticles to be sensitive to different temperature and pressure regimes, it is necessary to understand the mechanical response of crystalline MoS2 under mechanical loading. Specifically, the fundamental mechanism associated with the nucleation …

Blunt Impact Performance Evaluation Of Helmet Lining Systems For Military And Recreational Use, Jaclyn Siniora, Ryan Taylor, Darren Suey

Industrial Technology and Packaging

With the increasing problem in collegiate athletes experiencing injuries to the brain, different helmet liners where put to the test to see which liner provided athletes the greatest protection under specific conditions.

This senior project evaluates five different liners in football helmets. Each of the helmet liners were tested at three different temperatures: hot, cold, and ambient. Each helmet had seven different impact locations which were put to the test. The project was designed to be used to test ACH military combat liners as well. Due to shipping bottle necks the ACH combat liners have been left to future Cal …

Biaxial & Twist Testing Of Composite Carbon-Fiber Sandwich Panels For Automotive Racing Vehicles, Erik Eckberg

Materials Engineering

Composite sandwich panels were constructed with 4-ply plain weave carbon-fiber/epoxy face sheets in the 0^o/45^o/0^o/45^o orientation and 1/8^th inch Nomex honeycomb core. The panels were cut into 5-inch square test plates for mechanical testing. All testing was done on a fixture designed and fabricated by Pratt & Miller Engineering and installed on an Instron testing system at Cal Poly. The twist test was performed by supporting diagonal corners of the plate while simultaneously loading the opposite two corners at a crosshead rate of .06 in/min (ASTM 3044-94R11). Out of 10 panels tested, …

Biomedical Properties And Preparation Of Iron Oxide-Dextran Nanostructures By Maple Technique, Carmen Steluta Ciobanu, Simona Liliana Iconaru, Eniko Gyorgy, Mihaela Radu, Marieta Costache, Anca Dinischiotu, Philippe Le Coustumer, Khalid Lafdi, Daniela Predoi

Chemical and Materials Engineering Faculty Publications

Background: In this work the chemical structure of dextran-iron oxide thin films was reported. The films were obtained by MAPLE technique from composite targets containing 10 wt. % dextran with 1 and 5 wt.% iron oxide nanoparticles (IONPs). The IONPs were synthesized by co-precipitation method. A KrF* excimer laser source (λ = 248 nm, τFWHM≅25 ns, ν = 10 Hz) was used for the growth of the hybrid, iron oxide NPs-dextran thin films.

Results: Dextran coated iron oxide nanoparticles thin films were indexed into the spinel cubic lattice with a lattice parameter of 8.36 Å. The particle sized calculated was …

Carbon Nanotubes Grown On Glass Fiber As A Strain Sensor For Real Time Structural Health Monitoring, Matthew Boehle, Qiong Jiang, Lingchuan Li, Alexandre Lagounov, Khalid Lafdi

Chemical and Materials Engineering Faculty Publications

In order to more effectively monitor the health of composite structures, a fuzzy fiber sensor has been developed. The fuzzy fiber is a bundle of glass fibers with carbon nanotubes or nanofibers (CNTs or CNFs) grown on the surface. The nanotube coating makes the fiber bundle conductive while the small conductive path increases sensitivity. The fuzzy fiber sensor can replace conventional metal foil strain gauges in composite applications. The electrical response of the sensor is monitored in real time to measure strain, vibration, cracking and delamination. Continuous monitoring provides instant notification of any problems. Implementation of this sensor network in …

Limited Thermal Conductance Of Metal-Carbon Interfaces, Jaime J. Gengler, Sergei V. Shenogin, John E. Bultman, Ajit K. Roy, Andrey A. Voevodin, Christopher Muratore

Chemical and Materials Engineering Faculty Publications

The thermal conductance for a series of metal-graphite interfaces has been experimentally measured with time-domain thermoreflectance (TDTR). For metals with Debye temperatures up to ∼400 K, a linear relationship exists with the thermal conductance values. For metals with Debye temperatures in excess of ∼400 K, the measured metal-graphite thermal conductance values remain constant near 60 MW m−2 K−1. Titanium showed slightly higher conductance than aluminum, despite the closeness of atomic mass and Debye temperature for the two metals. Surface analysis was used to identify the presence of titaniumcarbide at the interface in contrast to the aluminum and gold-carbon interfaces (with …

Design Mixers To Minimize Effects Of Erosion And Corrosion Erosion, Julian B. Fasano, Eric E. Janz, Kevin J. Myers

Chemical and Materials Engineering Faculty Publications

A thorough review of the major parameters that affect solid-liquid slurry wear on impellers and techniques for minimizing wear is presented. These major parameters include (i) chemical environment, (ii) hardness of solids, (iii) density of solids, (iv) percent solids, (v) shape of solids, (vi) fluid regime (turbulent, transitional, or laminar), (vii) hardness of the mixer's wetted parts, (viii) hydraulic efficiency of the impeller (kinetic energy dissipation rates near the impeller blades), (ix) impact velocity, and (x) impact frequency. Techniques for minimizing the wear on impellers cover the choice of impeller, size and speed of the impeller, alloy selection, and surface …

Artificial Muscle Project: Process Development Of Polydimethyl Siloxane Thin Films For Use In Dielectric Electroactive Polymer Artificial Muscle Actuators, Vincent J. Gayotin, Richard W. Morrison, Paul A. Preisser

Materials Engineering

An artificial muscle design was created founded on the principles of a dielectric electroactive polymer (DEAP), which is fundamentally similar to a capacitor. A polydimethyl siloxane (PDMS)-based elastomer, Sylgard 184 from Dow Corning, was chosen for the design and spun coat onto polystyrene (PS) Petri dishes at varying speeds to create a thin film, using speeds of 2000 rpm, 3000 rpm, 4000 rpm, 5000 rpm, and 6000 rpm. The film thicknesses were measured optically through use of a microscope with coupled computer imaging software to generate a characteristic curve of film thickness to spin speed, achieving a minimum film thickness …

Investigating Wood Welding Parameters Using A Prototype Welding Machine, Timothy R. Melin

Master's Theses

Understanding how different processing variables influence wood welded bonds is vital if the technique will ever be used to create engineered lumber without using adhesives. A variation of vibration welding, wood welding uses pressure and friction to bond materials together. During welding, heat causes a softening in the wood, a naturally occurring composite material. This softening leads to fiber entanglement and a bond forms upon cooling.

The goal of this research was to investigate several processing aspects of the wood welding procedure. A prototype wood welding machine, designed and fabricated from the ground up, was used to investigate the effects …

Validation Of A Secondary Fabric Supplier And Characterization Of Alternate Cores For Use In The Aptera 2e Sandwich Core Composite, Bryan Rogers

Materials Engineering

Polymer matrix composites’ high strength to weight ratio has made them an ideal material choice for use in lightweight transportation vehicles. Aptera Motors, a company based out of Oceanside, CA, is currently developing a next-generation high efficiency passenger vehicle called the Aptera 2e. The 2e’s body is composed of a sandwich core composite containing laminates of E-glass fibers embedded within an epoxy matrix sandwiched between a polyester hexagonal core. This project looked to validate a secondary fabric supplier for use in Aptera’s composite and characterize the core shear properties of two alternate core materials for future iterations of Aptera’s vehicle. …

Electrostatic Quadrupole Plasma Mass Spectrometer Measurements During Thin Film Depositions Using Simultaneous Matrix Assisted Pulsed Laser Evaporation And Magnetron Sputtering, Chad N. Hunter, Michael H. Check, Christopher Muratore, Andrey A. Voevodin

Chemical and Materials Engineering Faculty Publications

A hybrid plasma deposition process, combining matrix assisted pulsed laser evaporation (MAPLE) of carbon nanopearls (CNPs) with magnetron sputtering of gold was investigated for growth of composite films, where 100 nm sized CNPs were encapsulated into a gold matrix. Composition and morphology of such composite films was characterized with x-ray photoelectron spectroscopy, scanning electron microscopy, and transmission electron microscopy (TEM) analysis. Carbondeposits on a gold magnetron sputter target and carbon impurities in the gold matrices of depositedfilms were observed while codepositing from gold and frozen toluene-CNP MAPLE targets in pure argon. Electrostatic quadrupole plasma analysis was used to determine that …

Chameleon Coatings: Adaptive Surfaces To Reduce Friction And Wear In Extreme Environments, Christopher Muratore, Andrey A. Voevodin

Chemical and Materials Engineering Faculty Publications

Adaptive nanocomposite coating materials that automatically and reversibly adjust their surface composition and morphology via multiple mechanisms are a promising development for the reduction of friction and wear over broad ranges of ambient conditions encountered in aerospace applications, such as cycling of temperature and atmospheric composition. Materials selection for these composites is based on extensive study of interactions occurring between solid lubricants and their surroundings, especially with novel in situ surface characterization techniques used to identify adaptive behavior on size scales ranging from 10−10 to 10−4 m. Recent insights on operative solid-lubricant mechanisms and their dependency upon the ambient environment …

Design And Development Of Rapid Battery Exchange Systems For Electric Vehicles To Be Used As Efficient Student Transportation, Jonathan A. Bevier

Master's Theses

Rapid battery exchange systems were built for an electric van and pedal assist electric bike as a method of eliminating the need to recharge the vehicles batteries in order to increase the feasibility of using electric propulsion as a method of efficient student transportation. After selecting proper materials it was found that the systems would need a protective coating to ensure consistent operation. 1020 cold rolled steel samples coated with multiple thicknesses of vinyl resin paint, epoxy resin paint, and powder coating were subjected to environmental wear tests in order to determine if the type and thickness of common protective …

Effect Of Carbon Nanofiber-Matrix Adhesion On Polymeric Nanocomposite Properties—Part Ii, Khalid Lafdi, William Fox, Matthew Matzek, Emel Yildiz

Chemical and Materials Engineering Faculty Publications

A successful integration of two independent phases with good adhesion is imperative for effective translation of superior carbon nanofiber filler properties into a physically superior carbon nanocomposite. Carbon nanofibers were subjected to electrochemical oxidation in 0.1 M nitric acid for varying times.

The strength of adhesion between the nanofiber and an epoxy matrix was characterized by flexural strength and modulus. The surface functional groups formed and their concentration of nanofibers showed a dependence on the degree of oxidation. The addition of chemical functional groups on the nanofiber surface allows them to physically and chemically adhere to the continuous resin matrix. …

Carbon Nanoadditives To Enhance Latent Energy Storage Of Phase Change Materials, Shadab Shaikh, Khalid Lafdi, Kevin P. Hallinan

Chemical and Materials Engineering Faculty Publications

Latent energy storage capacity was analyzed for a system consisting of carbon nanoparticlesdopedphase changematerials (PCMs). Three types of samples were prepared by doping shell wax with single wall carbon nanotubes(SWCNTs), multiwall CNTs, and carbon nanofibers. Differential scanning calorimetry was used to measure the latent heat of fusion. The measured values of latent heat for all the samples showed a good enhancement over the latent heat of pure wax. A maximum enhancement of approximately 13% was observed for the wax/SWCNT composite corresponding to 1% loading of SWCNT. The change in latent heat was modeled by using an approximation for the intermolecular …

Nitrogen And Hydrogen Plasma Treatments Of Multiwalled Carbon Nanotubes, John G. Jones, A. R. Waite, Christopher Muratore, Andrey A. Voevodin

Chemical and Materials Engineering Faculty Publications

This article investigates plasma treatment of vertically aligned multiwall carbon nanotube (CNT) films in different plasma environments for modification of surface chemistry and morphology. The surfaces of the CNTs were functionalized with a pulsed dc plasma treatment, where the power was directly applied to the nanotube film in low pressure argon/nitrogen and argon/hydrogen backgrounds. Optical emission spectroscopy was used to detect atomic and molecular excitations in the gas mixtures as well as in pure gases in the vicinity of the CNT films. In situx-ray photoelectron spectroscopy was performed on the treated samples to examine CNT surface chemistry after treatment. …

Signaling Pathways Activated By Interleukin-2 And Interluekin-4 Receptors Mediate T Lymphocyte Clonal Expansion, Kristen K. Comfort

Chemical and Materials Engineering Faculty Publications

Cells sense and respond to chemical and physical stimuli through signal transduction pathways, which mediate cell proliferation, differentiation, migration, and survival. The cytokines interleukin-2 (IL-2) and interleukin-4 (IL-4) are key regulators of the adaptive immune system, particularly influencing the clonal expansion and differentiation of T cells. At least in culture, both synergistic and antagonistic effects of IL-2 and IL-4 co-stimulation have been reported; the antagonism, when observed, is thought to arise from the utilization of a common subunit shared by IL-2 and IL-4 receptors. We have sought to characterize IL-2 and IL-4 signaling at the level of intracellular pathways activated …

Thermal Conductivity Improvement In Carbon Nanoparticle Doped Pao Oil: An Experimental Study, Shadab Shaikh, Khalid Lafdi, Rengasamy Ponnappan

Chemical and Materials Engineering Faculty Publications

The present work involves a study on the thermal conductivity of nanoparticle-oil suspensions for three types of nanoparticles, namely, carbon nanotubes(CNTs), exfoliated graphite (EXG), and heat treated nanofibers (HTT) with PAO oil as the base fluid. To accomplish the above task, an experimental analysis is performed using a modern light flash technique (LFA 447) for measuring the thermal conductivity of the three types of nanofluids, for different loading of nanoparticles.

The experimental results show a similar trend as observed in literature for nanofluids with a maximum enhancement of approximately 161% obtained for the CNT-PAO oil suspension. The overall percent enhancements …

Experimental Study On The Influence Of Foam Porosity And Pore Size On The Melting Of Phase Change Materials, Khalid Lafdi, Osama Mesalam Mesalhy, Shadab Shaikh

Chemical and Materials Engineering Faculty Publications

Experimental study was carried out to study the phase change heat transfer within a composite of phase change material (PCM) infiltrated high thermal conductivity foam. An experimental setup was built to measure the temperature profiles and capture the melting evolution of the PCM inside aluminum foams. Aluminum foams were used as the porous material, and low melting temperature paraffin wax was used as the PCM. It was observed from the results that the system parameters of the wax/foam composite had a significant influence on its heat transfer behavior.

By using higher porosity aluminum foam, the steady-state temperature was reached faster …

Effect Of Carbon Nanofiber Heat Treatment On Physical Properties Of Polymeric Nanocomposites—Part I, Khalid Lafdi, William Fox, Matthew Matzek, Emel Yildiz

Chemical and Materials Engineering Faculty Publications

The definition of a nanocomposite material has broadened significantly to encompass a large variety of systems made of dissimilar components and mixed at the nanometer scale. The properties of nanocomposite materials also depend on the morphology, crystallinity, and interfacial characteristics of the individual constituents. In the current work, vapor-grown carbon nanofibers were subjected to varying heat-treatment temperatures.

The strength of adhesion between the nanofiber and an epoxy (thermoset) matrix was characterized by the flexural strength and modulus. Heat treatment to 1800C∘ demonstrated maximum improvement in mechanical properties over that of the neat resin, while heat-treatment to higher temperatures demonstrated a …

Interfacial And Capillary Pressure Effects On The Thermal Performance Of Wax/Foam Composites, Mohammad Rajab Almajali, Khalid Lafdi, Shadab Shaikh

Chemical and Materials Engineering Faculty Publications

A numerical investigation study was performed to study the phase change behavior of wax/foam composite encapsulated in an aluminum casing. Two types of foam materials, namely, aluminum and carbon, were infiltrated with paraffin wax. The progress of melt interface and temperature distribution within the encapsulated composite was analyzed using computational fluid dynamics software (CFD). A two-energy equation model was implemented in the CFD software through the use of user-defined function (UDF). Interfacial effects influencing the heat transfer process at the casing-composite junction and between the wax-foam surfaces within the composite were addressed through the use of separate UDF. In addition, …

Oxygen Plasma Treatment And Deposition Of Cnx On A Fluorinated Polymer Matrix Composite For Improved Erosion Resistance, Christopher Muratore, Andras Korenyi-Both, John E. Bultman, A. R. Waite, John G. Jones, T. M. Storage, Andrey A. Voevodin

Chemical and Materials Engineering Faculty Publications

The use of polymer matrix composites in aerospace propulsion applications is currently limited by insufficient resistance to erosion by abrasive media. Erosion resistant coatings may provide necessary protection; however, adhesion to many high temperature polymer matrix composite (PMC) materials is poor. A low pressure oxygen plasma treatment process was developed to improve adhesion of CNx coatings to a carbon reinforced, fluorinated polymer matrix composite. Fullerene-like CNx was selected as an erosion resistant coating for its high hardness-to-elastic modulus ratio and elastic resilience which were expected to reduce erosion from media incident at different angles (normal or glancing) relative to the …