Polymer and Organic Materials Commons^™

Interfacial Interactions Between Carbon Nanoparticles And Conjugated Polymers, Yanqi Luo

Master's Theses

Conjugated polymer based electronics, a type of flexible electronic devices, can be produced from solution by traditional printing and coating processes in a roll-to-roll format such as papers and graphic films. This shows great promise for the emerging energy generation and conversion. The device performance of polymer electronics is largely dependent of crystalline structures and morphology of photoactive layers. However, the solution crystallization kinetics of conjugated polymers in the presence of electron acceptor nanoparticles has not been fully understood yet. In this study, solution crystallization kinetics of poly (3-hexylthiophene) in the presence of carbon nanotubes and graphene oxide has been …

Electroplating Of Nanoengineered Polymer Substrate, Brandon Voelker

Masters Theses

The development of a polyethylene based polymer with metallic inclusions, a nanoengineered polymer, has recently opened up great potential for many new commercial and industrial applications. The major advantage of developing these nanoengineered polymers is to be able to tailor the resistance and other properties by varying the composition of the polymer. The industrial usage of this polymer benefits from the addition of an electrically conductive, metallic coating. This research develops methods of electroplating nickel and copper layers on to the polymer substrates using DC and pulsed techniques.

Electroplating is conducted in a 1000 mL beaker using a specialized plating …

Electrospinning Applications Air Filtration And Superhydrophobic Materials, Negar Ghochaghi, Adetoun Taiwo

Graduate Research Posters

Electrospinning is a widely applicable technique that generates non-woven fibers in the micro and nano range. In this project two of its applications are highlighted namely filtration media and enhancement of wettability. The first project demonstrates that electrospinning can be used to produce new fiber filtration media with controlled microstructure. The bimodal and unimodal orthogonal and random filters were made and characterized against their filtration efficiency and pressure drop. Figure of Merit (FOM) was also calculated and discussed. It is shown that the FOM increases when the electrospun fibers are arranged into alternating layers of aligned course and fine fibers. …

Addressing Public Health Risks Of Persistent Pollutants Through Nutritional Modulation And Biomimetic Nanocomposite Remediation Platforms, Bradley J. Newsome

Theses and Dissertations--Chemistry

Due to their relative chemical stability and ubiquity in the environment, chlorinated organic contaminants such as polychlorinated biphenyls (PCBs) pose significant health risks and enduring remediation challenges. Engineered nanoparticles (NPs) provide a novel platform for sensing/remediation of these toxicants, in addition to the growing use of NPs in many industrial and biomedical applications, but there remains concern for their potential long-term health effects. Research highlighted herein also represents a transdisciplinary approach to address human health challenges associated with exposure to PCBs and NPs. The objectives of this dissertation research are two-fold, 1) to develop effective methods for capture/sensing and remediation …

Friction And Wear Of Polytetrafluoroethylene/Graphene Oxide Composite Thin Films, Justin Kyle Carter

Graduate Theses and Dissertations

Polytetrafluoroethylene (PTFE) is a commonly used solid lubricant due to its low coefficient of friction and chemical inertness. As a polymer, PTFE suffers from high wear and low adhesion to substrates limiting its use as a thin film. Thin PTFE films are ideal candidates for solid lubrication in micro-machines and bearing applications. The main goal of this work is to enhance the durability of thin PTFE films through the addition of few layered graphene oxide (GO) as filler. In order to address adhesion issues, the addition of an adhesive layer of polydopamine (PDA) between stainless steel substrates and thin PTFE …

Pan Nanofibers And Nanofiber Reinforced Composites, Cheng Ren

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Nanomaterials play an important role in the development of nanotechnology. They possess unique mechanical, physical, and chemical properties coupled with small size and ultrahigh surface area that can provide critical advantages for applications. Continuous nanofibers attract special interest due to their dual nano-macro nature and ability to bridge scales. Nanofibers are being considered for a broad range of applications spanning advanced filters, separation membranes, ultrasensitive sensors, micro/nano actuators, nanoprobes, tissue engineering scaffolds, protective and smart closing, and multifunctional composites. Most of these applications require certain mechanical properties and robustness. However, the literature on the mechanical behavior of nanofibers and their …

Design And Fundamental Understanding Of Minimum Quantity Lubrication (Mql) Assisted Grinding Using Advanced Nanolubricants, Parash Kalita

Graduate Theses and Dissertations

Abrasive grinding is widely used across manufacturing industry for finishing parts and components requiring smooth superficial textures and precise dimensional tolerances and accuracy. Unlike any other machining operations, the complex thermo-mechanical processes during grinding produce excessive friction-induced energy consumption, heat, and intense contact seizures. Lubrication and cooling from grinding fluids is crucial in minimizing the deleterious effects of friction and heat to maximize the output part quality and process efficiency. The conventional flood grinding approach of an uneconomical application of large quantities of chemically active fluids has been found ineffective to provide sufficient lubrication and produces waste streams and pollutants …

Experimental Study Of Nanofiber Production Through Forcespinning, Simon Padron, Arturo Fuentes, Dumitru Caruntu, Karen Lozano

Mechanical Engineering Faculty Publications

A newly developed method of producing nanofibers, called forcespinning, has proven to be a viable alternative to mass produce nanofibers. Unlike electrospinning, the most common method currently being employed (which draws fibers through the use of electrostatic force), forcespinning utilizes centrifugal forces which allow for a host of new materials to be processed into nanofibers (given that electric fields are not required) while also providing a significant increase in yield and ease of production. This work presents a detailed explanation of the fiber formation process. The study is conducted using high speed photography to capture the jet initiation process at …

Influence Of Surface Modification On Properties And Applications Of Complex Engineered Nanoparticles, Binghui Wang

Theses and Dissertations--Chemical and Materials Engineering

Complex engineered nanoparticles (CENPs) are being used on various applications. Their properties are different from those of neat nanoparticles. The dissertation explores these differences from four aspects: 1) Modify carbon nanomaterials’ inert surfaces and investigate the effect on thermal and rheological behavior of their dispersions; 2) Generate self-assembly bi-layer structure of oxide nanoparticles via surface modification; 3) Study interaction between lysozyme and different surface-charged ceria nanoparticles; 4) Investigate the biodistribution and transformations of CENPs in biological media.

An environment-friendly surface modification was developed to modify surfaces of carbon nanomaterials for increasing their affinity to non-polar fluid. It can offset formation …

Silica Nanoparticle-Based Coatings With Superhydrophilic And Superhydrophobic Properties, Robert Andrew Fleming

Graduate Theses and Dissertations

Superhydrophilic and superhydrophobic surfaces have potential for implementation into a variety of fields, including self-cleaning surfaces, anti-fogging transparent materials, and biomedical applications. In this study, sandblasting, oxygen plasma treatments, silica nanoparticle films, and a low surface energy fluorocarbon film were employed to change the natural surface wettability of titanium, glass, and polyethylene terephthalate (PET) substrates, with an aim to produce superhydrophilic and superhydrophobic behavior. The effects of these surface modifications are characterized by water contact angles (WCAs), surface wetting stability, surface morphology and roughness, surface elemental composition, and optical transmittance measurements. The results show that stable superhydrophilic and superhydrophobic surfaces …

Design, Fabrication, Testing Of Cnt Based Isfet And Characterization Of Nano/Bio Materials Using Afm, Zhuxin Dong

Graduate Theses and Dissertations

A combination of Carbon Nanotubes (CNTs) and Ion Selective Field Effect Transistor (ISFET) is designed and experimentally verified in order to develop the next generation ion concentration sensing system. Micro Electro-Mechanical System (MEMS) fabrication techniques, such as photolithography, diffusion, evaporation, lift-off, packaging, etc., are required in the fabrication of the CNT-ISFET structure on p-type silicon wafers. In addition, Atomic Force Microscopy (AFM) based surface nanomachining is investigated and used for creating nanochannels on silicon surfaces. Since AFM based nanomanipulation and nanomachining is highly controllable, nanochannels are precisely scratched in the area between the source and drain of the FET where …

Pulse Sharpening Effects Of Thin Film Ferroelectric Transmission Lines, Robert J. Sleezer

Graduate Theses and Dissertations

Advances in material science have resulted in the development of electrically nonlinear high dielectric thin film ferroelectrics, which have led to new opportunities for the creation of novel devices. This dissertation investigated one such device: a low voltage nonlinear transmission line (NLTL). A finite element simulation of ferroelectric transmission lines showed that NLTLs are capable of creating shockwaves. Additionally, if the losses are kept sufficiently low, it was shown that voltage gain should be possible. Furthermore, a method of accounting for material dispersion was developed. Results from simulations including material dispersion showed that temporal solitons might be possible from a …

Semiconductor Nanocrystals: From Quantum Dots To Quantum Disks, Zheng Li

Graduate Theses and Dissertations

The bottom-up colloidal synthesis opened up the possibility of finely tuning and tailoring the semiconductor nanocrystals. Numerous recipes were developed for the preparation of colloidal semiconductor nanocrystals, especially the traditional quantum dots. However, due to the lack of thorough understanding to those systems, the synthesis chemistry is still on the empirical level. CdS quantum dots synthesis in non-coordinating solvent were taken as a model system to investigate its molecular mechanism and formation process, ODE was identified as the reducing agent for the preparation of CdS nanocrystals, non-injection and low-temperature synthesis methods developed. In this model system, we not only proved …

Active Response Of Polymer Materials From External Stimuli – Solvents And Light; Grafting Reactions On Perovskite Layers, Jianxia Zhang

LSU New Orleans Theses and Dissertations

The active response of a series of polymeric materials was investigated. Both solvent activated and light activated thin films and wire systems show dynamic behaviors when exposed to different stimuli.

Solvent mediated fluxional behavior of polymer thin films involved extensive, rapid curling both on infusion and evaporation of good solvents. These films can be either lab-fabricated ones or commercial ones, and the curling behavior can be as fast as seconds. Conditions including polymer materials, chosen solvents, and film geometry can affect the behavior.

Methods that allowed for the creation and retention of distorted wire structures were also developed; the asymmetric …

Nanocharacterization Of Porous Materials With Atomic Force Microscopy, Yasemin Kutes

Master's Theses

Scanning Probe Microscopy techniques have proven very useful in the investigation of porous nanostructured surfaces. Especially, Atomic Force Microscopy (AFM) has been widely used due to its compatibility with non-conducting surfaces. In particular, AFM often complements other techniques like scanning and transmission electron microscopy by providing quantitative surface information coupled with nanoscale spatial resolution. Its ability to operate in fluid is also important, as this allows researchers to mimic the physiological environment of biological materials and systems. In this work, two main types of porous materials are studied with AFM, including Phosphoric Acid Fuel Cell (PAFC) electrode catalyst layers, and …

Physiochemical And Nanomanipulation Studies Of Carbon Nanomaterials, Siva Naga Sandeep Chalamalasetty

Graduate Theses and Dissertations

Carbon nanomaterials are, without a doubt, one of man's wonder creations. Though these nanomaterials are a very recent trend, extraordinary electromechanical properties and the light weightiness of these nanomaterials attracted the attention of researchers. Although vast research has been done since the start of the US nanotechnology initiative, much effort was in the area of synthesis and characterization of the nanomaterials. However, most of the traditional macroscopic material's theories fail at the nanoscale level, and since the material properties are dependent on size and structure at nanoscale level, the behavior of the carbon nanomaterials in different environments needs attention. High …

Effect Of Extracellular Matrix (Ecm) Protein Micropatterns On The Behavior Of Human Neuroblastoma Cells, Ishwari Poudel

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Recent advances in patterning techniques and emerging surface microtechnologies have allowed cell micropatterning to control spatial location of the cells on a surface as well as cell shape, attachment area, and number of contacting neighbor cells. These parameters play important roles in cell cellular behaviors. Cell micropatterning has thus become one of the most important strategies for biomedical applications, such as, tissue engineering, diagnostic immunoassays, lab-on-chip devices, bio-sensing, etc., and cell biology studies as well. For neuronal cells, there have been attempts to distribute neuronal cells on specific patterns to control cell-to-cell interaction. However, there have been very limited understanding …

Interfacial Energy Between Carbon Nanotubes And Polymers Measured From Nanoscale Peel Tests In The Atomic Force Microscope, Mark C. Strus, Camilo I. Cano, R. Byron Pipes, Cattien V. Nguyen, Arvind Raman

Other Nanotechnology Publications

The future development of polymer composite materials with nanotubes or nanoscale fibers requires the ability to understand and improve the interfacial bonding at the nanotube-polymer matrix interface. In recent work [Strus MC, Zalamea L, Raman A, Pipes RB, Nguyen CV, Stach EA. Peeling force spectroscopy: exposing the adhesive nanomechanics of one-dimensional nanostructures. Nano Lett 2008;8(2):544–50], it has been shown that a new mode in the Atomic Force Microscope (AFM), peeling force spectroscopy, can be used to understand the adhesive mechanics of carbon nanotubes peeled from a surface. In the present work, we demonstrate how AFM peeling force spectroscopy can be …

Modeling And Simulation To Investigate Effects Of Static Mixer, Carrier Gas, Temperature And Pressure On The Mixing Ratio Of Carbon Nanotubes Growth Reactors, David Addie Noye

Dissertations and Theses @ UNI

The problem of this study was to investigate the effects of static mixer, carrier gas, carrier gas inlet pressures, and reactor operating temperatures on the mixing ratio of carbon nanotube synthesizing reactor. The methodology included design of static mixers, mathematical modeling, and computer modeling and simulation experiments.

The simulation experiment was performed based on single phase carrier gas modeling due to difficulty and time for three phase fluid modeling. First only nitrogen carrier gas in addition to the other three factors under constant inlet flow velocity and inlet temperature was simulated. Secondly, the same procedure was applied to argon carrier …