Polymer and Organic Materials Commons^™

Design And Development Of Rapid Battery Exchange Systems For Electric Vehicles To Be Used As Efficient Student Transportation, Jonathan A. Bevier

Master's Theses

Rapid battery exchange systems were built for an electric van and pedal assist electric bike as a method of eliminating the need to recharge the vehicles batteries in order to increase the feasibility of using electric propulsion as a method of efficient student transportation. After selecting proper materials it was found that the systems would need a protective coating to ensure consistent operation. 1020 cold rolled steel samples coated with multiple thicknesses of vinyl resin paint, epoxy resin paint, and powder coating were subjected to environmental wear tests in order to determine if the type and thickness of common protective …

Interfacial Energy Between Carbon Nanotubes And Polymers Measured From Nanoscale Peel Tests In The Atomic Force Microscope, Mark C. Strus, Camilo I. Cano, R. Byron Pipes, Cattien V. Nguyen, Arvind Raman

Other Nanotechnology Publications

The future development of polymer composite materials with nanotubes or nanoscale fibers requires the ability to understand and improve the interfacial bonding at the nanotube-polymer matrix interface. In recent work [Strus MC, Zalamea L, Raman A, Pipes RB, Nguyen CV, Stach EA. Peeling force spectroscopy: exposing the adhesive nanomechanics of one-dimensional nanostructures. Nano Lett 2008;8(2):544–50], it has been shown that a new mode in the Atomic Force Microscope (AFM), peeling force spectroscopy, can be used to understand the adhesive mechanics of carbon nanotubes peeled from a surface. In the present work, we demonstrate how AFM peeling force spectroscopy can be …

The Effects Of Build Orientation, Diameter And Printhead Life On The Cylindricity Of Three-Dimensionally Printed Parts, Troy E. Ollison

All-Inclusive List of Electronic Theses and Dissertations

Rapid prototyping (RP) technologies have become more than just a fast and inexpensive way to produce prototypes. Today RP is widely used to produce functional prototypes, end-use parts and tooling as well as visual prototypes. When RP is used for end-use parts with interconnected moving assemblies or for producing metal casting molds which must have sufficient material for machining tolerances, accuracy is very critical. However, in general, accuracy of the finished RP parts is relatively low lll compared to parts produced by traditional manufacturing processes. The understanding of why some of these accuracy differences exist is either unknown or not …

Impact Of A Microwave Curing Process On Tensile Strength Of Selected Carbon Fiber Composites, Brian B. Balzer

All-Inclusive List of Electronic Theses and Dissertations

The traditional process for curing carbon fiber (CF) composites has been the autoclave system. A review of recent research indicates curing CF composites in a microwave oven has the potential for reducing processing time. The problem statement of the experimental study was that the impact of a microwave curing process on tensile strength of selected CF composite specimens was unknown. The research study describes the statistical procedure and analysis of data to answer the specific question for the experimental trials: What is the effect on the tensile strength of cured CF composite samples due to the relationship of the autoclave …

Influence Of Van Der Waals Forces On Increasing The Strength And Toughness In Dynamic Fracture Of Nanofibre Networks: A Peridynamic Approach, Florin Bobaru Ph.D.

Department of Engineering Mechanics: Faculty Publications

The peridynamic method is used here to analyse the effect of van der Waals forces on the mechanical behaviour and strength and toughness properties of three-dimensional nanofibre networks under imposed stretch deformation. The peridynamic formulation allows for a natural inclusion of long-range forces (such as van der Waals forces) by considering all interactions as ‘long-range’. We use van der Waals interactions only between different fibres and do not need to model individual atoms. Fracture is introduced at the microstructural (peridynamic bond) level for the microelastic type bonds, while van der Waals bonds can reform at any time. We conduct statistical …

The Effects Of Machining On Structure And Tribological Properties Of Ultra High Molecular Weight Polyethylene For Artificial Joint Prostheses, Jinshan Song

Masters Theses

Understanding the effect of machining on the structure and property of subsurface layer of ultra high molecular weight polyethylene (UHMWPE) can significantly facilitate the increase in longevity of artificial joints. This study was performed to investigate the machining effects on the polymeric structure and tribological properties. Machining parameters include cutting speed, tool feed rate and depth of cut. Temperature rise was studied during machining to assess the extent of thermal degradation due to machining. Polymeric structure of the semicrystalline polymer was characterized using differential scanning calorimetry (DSC) in terms of melting enthalpy, crystallinity and melting temperature. Surface texture and hardness …

Mechanical And Tribological Properties Of Composites Of Recycled High Density Polyethylene And Recycled Rubber, Jason G. Boulanger

Masters Theses

This thesis presents a study on the mechanical and tribological properties of composite materials of recycled high density polyethylene (HDPE) and recycled rubber tire particles. The materials were compounded by extrusion and formed into test specimens by injection molding.

The first experiment studied the effect of recycled rubber percentage on mechanical properties of composites of recycled HDPE and recycled rubber. The mechanical properties included tensile strength, percent elongation, hardness, and impact resistance. Recycled rubber concentrations of 0, 5, 10, 15, 20, 25, and 30 percent were tested. The second experiment investigated the tribological properties of recycled HDPE and recycled rubber …

An Experimental Study Of An Advanced Polymeric Material For Use In Total Knee Replacements Including Gait Analysis Of Mobile Knee Bearings, Lisa Ann Scott

Mechanical & Aerospace Engineering Theses & Dissertations

The primary objectives of this research were to clinically examine the New Jersey Low Contact Stress (LCS)™ Rotating Platform and Meniscal knee bearing systems and to investigate the tribological properties of a new polymer for potential application in total joint replacement. Thus, clinical studies were performed on subjects having the LCSTM Rotating Platform knee bearing and subjects having the LCS™ meniscal knee bearing. The results indicated that there was a statistically significant difference in the braking force for both implant groups when compared to a control group. There was also a statistically significant difference noted for the LCS™ Rotating Platform …

Fiber Enhanced Viscoelastic Damping Polymers And Their Application To Passive Vibration Control, Houchun Xia

Mechanical & Aerospace Engineering Theses & Dissertations

A new composite damping material is investigated, which consists of a viscoelastic matrix and high elastic modulus fiber inclusions. This fiber enhanced viscoelastic damping polymer is intended to be applied to light-weight flexible structures as surface treatment for passive vibration control. A desirable packing geometry for the composite material is proposed, which is expected to produce maximum shear strain in the viscoelastic damping matrix. Subsequently, a micromechanical model is established in which the effect of fiber segment length and relative motion between neighboring fibers are taken into account. Based on this model, closed form expressions for the effective storage and …

Wood Finishing For Tree Samples Of Five Honduran Species, Amilcar A. Cruz

Graduate Research Papers

This research report will study the application of four wood finishing techniques to samples of each of five species of Honduran hardwood.

These four wood finishing methods are: The varnish-method, the lacquer method, the antiquing method and the oil-rub method. The researcher will attempt to determine which is the best method for each of the five species.

Analysis Of Moisture Absorption And Diffusion In Fiber Reinforced Polymeric Resin-Matrix Composite Materials, Stephen Stern Tompkins

Mechanical & Aerospace Engineering Theses & Dissertations

The diffusion of moisture through fiber reinforced polymeric-matrix composite materials has been studied analytically. The diffusion in the orthotropic, nonhomogeneous material was modeled, in detail, with a two-dimensional transient diffusion analysis. An effective diffusivity for the composite was determined in terms of the fiber volume fraction and the resin diffusivity. This effective diffusivity is in better agreement with recent data than those previously determined using less complex models.

The influence of both material and environmental parameters on the moisture content of the composite was determined analytically. Predicted moisture contents were compared over a wide range of values for emittance, solar …

Electrostatic Fluidized Bed Plastic Powder Coating Process, Richard H. Florer

Graduate Research Papers

The overall objective is the fabrication of a functional electrostatic fluidized bed dry plastic powder coating apparatus which can be utilized in an Industrial Arts laboratory.