Polymer and Organic Materials Commons^™

Electrospinning Applications Air Filtration And Superhydrophobic Materials, Negar Ghochaghi, Adetoun Taiwo

Graduate Research Posters

Electrospinning is a widely applicable technique that generates non-woven fibers in the micro and nano range. In this project two of its applications are highlighted namely filtration media and enhancement of wettability. The first project demonstrates that electrospinning can be used to produce new fiber filtration media with controlled microstructure. The bimodal and unimodal orthogonal and random filters were made and characterized against their filtration efficiency and pressure drop. Figure of Merit (FOM) was also calculated and discussed. It is shown that the FOM increases when the electrospun fibers are arranged into alternating layers of aligned course and fine fibers. …

Physiological Fluid Specific Agglomeration Patterns Diminish Gold Nanorod Photothermal Characteristics, Kristen K. Comfort, Jared W. Speltz, Bradley M. Stacy, Larry R. Dosser, Saber M. Hussain

Chemical and Materials Engineering Faculty Publications

Investigations into the use of gold nanorods (Au-NRs) for biological applications are growing exponentially due to their distinctive physicochemical properties, which make them advantageous over other nanomaterials. Au-NRs are particularly renowned for their plasmonic characteristics, which generate a robust photothermal response when stimulated with light at a wavelength matching their surface plasmon resonance. Numerous reports have explored this nanophotonic phenomenon for temperature driven therapies; however, to date there is a significant knowledge gap pertaining to the kinetic heating profile of Au-NRs within a controlled physiological setting. In the present study, the impact of environmental composition on Au-NR behavior and degree …

The Biological Impact Of Concurrent Exposure To Metallic Nanoparticles And A Static Magnetic Field, Kristen K. Comfort, Elizabeth I. Maurer, Saber M. Hussain

Chemical and Materials Engineering Faculty Publications

The rapid advancement of technology has led to an exponential increase of both nanomaterial and magnetic field utilization in applications spanning a variety of sectors. While extensive work has focused on the impact of these two variables on biological systems independently, the existence of any synergistic effects following concurrent exposure has yet to be investigated. This study sought to ascertain the induced alterations to the stress and proliferation responses of the human adult low calcium, high temperature keratinocyte (HaCaT) cell line by the application of a static magnetic field (approximately 0.5 or 30 mT) in conjunction with either gold or …

Low Volume Dispensing With High Speed Dispensers, Sunny Agarwal

Graduate Dissertations and Theses

With the high pace of innovation in the semiconductor manufacturing industry, there has been an increasing demand for more energy efficient and environmental friendly products. This research relates to a complex process of fluid dispensing at low volumes on a printed circuit board. Currently, a more refined non-contact dispensing terminology named “Streaming” is widely used to stream out material at low volumes for various applications. The key solution is to frame a dispensing method that lends itself most closely to the requirements of a specific production process.

This study represents a detailed approach of dispensing low volumes of materials in …

Improved Deinkability Of Lep (Liquid Electrophotography) Digital Prints, Zheng Wei

Masters Theses

Digital printing plays a very important role in the life of modern society. With the development of digital printing technologies, and the increasing market share of digital printing, the amount of digital prints in waste paper is rapidly increasing. Under “green” manufacturing and environmental sustainability, deinking of digital print inks is an urgent problem that needs to be solved. Indigo is a typical series of HP (Hewlett-Packard) digital presses that use a liquid ink named ElectroInk (Liquid Electrophotography or LEP). The particle size of HP ElectroInk is very small, 1-2 microns, which is smaller than dry toners. But, during flotation, …

Improving The Efficiency Of P3ht:Icba Organic Solar Cells By Modifying The Photoactive Solution Preparation Step, Matthew Blaine Samson

Electrical & Computer Engineering Theses & Dissertations

Organic solar cells (OSCs) are a promising alternative to conventional silicon solar cells. These organic devices offer the promise of facile low cost large scale solution based processing on lightweight, flexible, plastic substrates. At the present state of the technology, however, OSCs exhibit relatively low power conversion efficiencies. To improve these efficiencies, new materials are constantly being developed.

One such material is the fullerene indene-C₆₀ bisadduct (ICBA). When implemented in a poly(3-hexylthiophene-2, 5-diyl) (P3HT) : ICBA bulk heterojunction solar cell, these devices exhibit open circuit voltages exceeding 0.8 V, a value much higher than the devices made implementing phenyl-C …

Materials Education And Research In Art And Design: A New Role For Libraries (Survey Stats), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

No abstract provided.

Materials Education And Research In Art And Design: A New Role For Libraries (Program Sheet), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

No abstract provided.

Materials Education And Research In Art And Design: A New Role For Libraries (Program Booklet), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

No abstract provided.

Materials Education And Research In Art And Design: A New Role For Libraries (Website), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

No abstract provided.

Materials Collection Creation And Administration: A New Role For Libraries (White Paper), Mark Pompelia

Materials Education and Research in Art and Design: A New Role for Libraries

The Problem/Opportunity: To define, identify, and guide design-based materials collections in academic settings and foster community among those with existing collections and/or those considering creating and supporting one.

Contents and topics:

1. What is a materials collection?
2. Why have a materials collection?
3. Acquisition strategies
4. Organizational approaches
5. Programming possibilities
6. Symposium summary
7. Resources

Applied Analysis Of Ionic Polymer Metal-Composite Actuators, Siul Ruiz, Benjamin Mead, Woosoon Yim

College of Engineering: Graduate Celebration Programs

• IPMC is a type of smart material called an electroactive polymer
• Consists of an ionic polymer such as Nafion or Flemion and a conducive metal such as platinum or gold
• COMSOL multi-physics simulations accurately model the experimental displacement results
• Optimization performed using the multi-physics model to find the maximum deflection, force, and twisting
• Using the closed loop control system accurate IPMC tip location can be achieved
• This control system has been extended to function using a computer mouse as an input

Study Of An Alternative Process For Oxidizing Vapor Grown Carbon Nanofibers Using Electron Beam Accelerators, Maria Cecília Evora, Donald A. Klosterman, Khalid Lafdi, Lingchuan Li, L.G.A. Silva

Chemical and Materials Engineering Faculty Publications

The use of a high-energy electron beam was explored in this study as an alternative technique for oxidizing vapor grown carbon nanofiber surfaces. The radiation exposures were carried out at three different electron beam facilities with beam energies of 1.5, 3.0 and 4.5 MeV and radiation doses ranging from 1000 to 3500 kGy. XPS analysis showed that oxygen was readily incorporated on the surface: the ratio O1s/C1s increased approximately by a factor of 4 when the carbon nanofibers were irradiated at 3500 kGy. The oxidized nanofibers exhibited better dispersion in a water/methanol solution (50% v/v) than as-received nanofibers. Raman spectroscopy …

Infrared Optical Properties Of Amorphous And Nanocrystalline Ta2o5 Thin Films, Trevor J. Bright, J. I. Watjen, Zhuomin Zhang, Christopher Muratore, Andrey A. Voevodin, D. I. Koukis, David B. Tanner, Daniel J. Arenas

Chemical and Materials Engineering Faculty Publications

The optical constants of tantalum pentoxide (Ta 2O5) are determined in a broad spectral region from the visible to the far infrared. Ta 2O5 films of various thicknesses from approximately 170 to 1600 nm aredeposited using reactive magnetron sputtering on Si substrates. X-ray diffraction shows that the as-deposited films are amorphous, and annealing in air at 800 °C results in the formation of nanocrystallineTa 2O5. Ellipsometry is used to obtain the dispersion in the visible and near-infrared. Two Fourier-transform infrared spectrometers are used to measure the transmittance and reflectance at wavelengths from 1 to 1000 μm. The surface topography and …

Cross-Plane Thermal Properties Of Transition Metal Dichalcogenides, Christopher Muratore, Vikas Varshney, Jaime J. Gengler, Jianjun Hu, John E. Bultman, Timothy M. Smith, Patrick J. Shamberger, Bo Qiu, Xiulin Ruan, Ajit K. Roy, Andrey A. Voevodin

Chemical and Materials Engineering Faculty Publications

In this work, we explore the thermal properties of hexagonal transition metal dichalcogenide compounds with different average atomic masses but equivalent microstructures. Thermal conductivity values of sputtered thin films were compared to bulk crystals. The comparison revealed a >10 fold reduction in thin film thermal conductivity. Structural analysis of the films revealed a turbostratic structure with domain sizes on the order of 5–10 nm. Estimates of phonon scattering lengths at domain boundaries based on computationally derived group velocities were consistent with the observed film microstructure, and accounted for the reduction in thermal conductivity compared to values for bulk crystals.

Tannic Acid Coated Gold Nanorods Demonstrate A Distinctive Form Of Endosomal Uptake And Unique Distribution Within Cells, Emily A. Untener, Kristen K. Comfort, Elizabeth I. Maurer, Christin M. Grabinski, Donald A. Comfort, Saber M. Hussain

Chemical and Materials Engineering Faculty Publications

One of the primary challenges associated with nanoparticle-dependent biological applications is that endosomal entrapment in a physiological environment severely limits the desired targeting and functionality of the nanoconstructs. This study sought to overcome that challenge through a systematic approach of gold nanorod (GNR) functionalization: evaluating the influence of both aspect ratio and surface chemistry on targeted cellular internalization rates and preservation of particle integrity. Owing to their unique spectral properties and enhanced surface area, GNRs possess great potential for the advancement of nanobased delivery and imaging applications. However, their ability for efficient intracellular delivery while maintaining their specific physiochemical parameters …

Characterization Of And Controlling Morphology Of Ultra-Thin Nanocomposites, Guy C. Laine

Theses and Dissertations--Chemical and Materials Engineering

Ultrathin film nanocomposites are becoming increasingly important for specialized performance of commercial coatings. Critical challenges for ultrathin film nanocomposites include their synthesis and characterization as well as their performance properties, including surface roughness, optical properties (haze, refractive index as examples), and mechanical properties. The objective of this work is to control the surface roughness of ultrathin film nanocomposites by changing the average particle size and the particle volume fraction (loading) of monomodal particle size distributions. This work evaluated one-layer and two-layer films for their surface properties. Monodispersed colloidal silica nanoparticles were incorporated into an acrylate-based monomer system as the model …

Flexural Rigidity Characterization Of Retrofitted Frp Plates, Steven J. Makonis Jr., Stella B. Bondi, Zia Razzaq

Civil & Environmental Engineering Faculty Publications

Presented herein is a procedure and numerical results for flexural rigidity characterization of Fiber Reinforced Polymer (FRP) plates retrofitted with various types of fabrics. The FRP plates were retrofitted with Kevlar® 49 (Aramid), Carbon Fiber (Harness-Satin H5), and Unidirectional Carbon Fiber (T700 Aerospace Grade) fabrics, respectively. The FRP plate flexural rigidity values were calculated with a central finitedifference iterative scheme while utilizing the experimental load-deflection relations based on bending tests. The tests were performed on each plate by applying a concentrated load at the center. A fourth-order partial differential equation of plate equilibrium was adopted to estimate the plate flexural …

Biomedical Properties And Preparation Of Iron Oxide-Dextran Nanostructures By Maple Technique, Carmen Steluta Ciobanu, Simona Liliana Iconaru, Eniko Gyorgy, Mihaela Radu, Marieta Costache, Anca Dinischiotu, Philippe Le Coustumer, Khalid Lafdi, Daniela Predoi

Chemical and Materials Engineering Faculty Publications

Background: In this work the chemical structure of dextran-iron oxide thin films was reported. The films were obtained by MAPLE technique from composite targets containing 10 wt. % dextran with 1 and 5 wt.% iron oxide nanoparticles (IONPs). The IONPs were synthesized by co-precipitation method. A KrF* excimer laser source (λ = 248 nm, τFWHM≅25 ns, ν = 10 Hz) was used for the growth of the hybrid, iron oxide NPs-dextran thin films.

Results: Dextran coated iron oxide nanoparticles thin films were indexed into the spinel cubic lattice with a lattice parameter of 8.36 Å. The particle sized calculated was …

Carbon Nanotubes Grown On Glass Fiber As A Strain Sensor For Real Time Structural Health Monitoring, Matthew Boehle, Qiong Jiang, Lingchuan Li, Alexandre Lagounov, Khalid Lafdi

Chemical and Materials Engineering Faculty Publications

In order to more effectively monitor the health of composite structures, a fuzzy fiber sensor has been developed. The fuzzy fiber is a bundle of glass fibers with carbon nanotubes or nanofibers (CNTs or CNFs) grown on the surface. The nanotube coating makes the fiber bundle conductive while the small conductive path increases sensitivity. The fuzzy fiber sensor can replace conventional metal foil strain gauges in composite applications. The electrical response of the sensor is monitored in real time to measure strain, vibration, cracking and delamination. Continuous monitoring provides instant notification of any problems. Implementation of this sensor network in …

Limited Thermal Conductance Of Metal-Carbon Interfaces, Jaime J. Gengler, Sergei V. Shenogin, John E. Bultman, Ajit K. Roy, Andrey A. Voevodin, Christopher Muratore

Chemical and Materials Engineering Faculty Publications

The thermal conductance for a series of metal-graphite interfaces has been experimentally measured with time-domain thermoreflectance (TDTR). For metals with Debye temperatures up to ∼400 K, a linear relationship exists with the thermal conductance values. For metals with Debye temperatures in excess of ∼400 K, the measured metal-graphite thermal conductance values remain constant near 60 MW m−2 K−1. Titanium showed slightly higher conductance than aluminum, despite the closeness of atomic mass and Debye temperature for the two metals. Surface analysis was used to identify the presence of titaniumcarbide at the interface in contrast to the aluminum and gold-carbon interfaces (with …

Design Mixers To Minimize Effects Of Erosion And Corrosion Erosion, Julian B. Fasano, Eric E. Janz, Kevin J. Myers

Chemical and Materials Engineering Faculty Publications

A thorough review of the major parameters that affect solid-liquid slurry wear on impellers and techniques for minimizing wear is presented. These major parameters include (i) chemical environment, (ii) hardness of solids, (iii) density of solids, (iv) percent solids, (v) shape of solids, (vi) fluid regime (turbulent, transitional, or laminar), (vii) hardness of the mixer's wetted parts, (viii) hydraulic efficiency of the impeller (kinetic energy dissipation rates near the impeller blades), (ix) impact velocity, and (x) impact frequency. Techniques for minimizing the wear on impellers cover the choice of impeller, size and speed of the impeller, alloy selection, and surface …

Determining A Method For Rendering Low Cost Cdse(Zns) Core(Shell) Quantum Dots Aqueous Soluble Via Amphiphilic Polymer Wrapping, Patrick Mcbride

Materials Engineering

Herein is described the procedure of two amphiphilic polymer wrapping techniques that may be employed for obtaining aqueous soluble quantum dots (QDs) for use in biological fluorescent imaging applications. The advent of QDs has led to new nanoscale fluorescent materials that exhibit unparalleled quantum yields (QYs), high resistance to photobleaching, tunable emissions, and
absorption over a large optical range. However, the QD synthesis employed here at Cal Poly to obtain bright, photostable CdSe(ZnS) core(shell) QDs involves the use of organic solvents and surfactants, leading to hydrophobic QDs. Since all of biology relies on aqueous solubility, this hydrophobicity creates a major …

Preparation Of Styrene Acrylic Copolymer Toner Resin By Solution Polymerization., Neo Su Siang

Student Works (2010-2019)

This project has investigated solution polymerization to produce toner resins. There are three stages: (i) synthesis of low molecular weight styrene acrylic copolymer; (ii) synthesis of high molecular weight styrene acrylic copolymer; (iii) mixing high and low molecular weight copolymers. Gel Permeation Chromatography (GPC) was used to study molecular weight distributions, Melt Flow Index (MFI) Instrument to study the flowability of resin, Differential Scanning Calorimetry (DSC) to study the thermal properties of resin, and acid number to quantitate the amount of acidic group in the resin. A comparison of properties between the experimental samples, patent’s claims, and commercial resins had …

Electrostatic Quadrupole Plasma Mass Spectrometer Measurements During Thin Film Depositions Using Simultaneous Matrix Assisted Pulsed Laser Evaporation And Magnetron Sputtering, Chad N. Hunter, Michael H. Check, Christopher Muratore, Andrey A. Voevodin

Chemical and Materials Engineering Faculty Publications

A hybrid plasma deposition process, combining matrix assisted pulsed laser evaporation (MAPLE) of carbon nanopearls (CNPs) with magnetron sputtering of gold was investigated for growth of composite films, where 100 nm sized CNPs were encapsulated into a gold matrix. Composition and morphology of such composite films was characterized with x-ray photoelectron spectroscopy, scanning electron microscopy, and transmission electron microscopy (TEM) analysis. Carbondeposits on a gold magnetron sputter target and carbon impurities in the gold matrices of depositedfilms were observed while codepositing from gold and frozen toluene-CNP MAPLE targets in pure argon. Electrostatic quadrupole plasma analysis was used to determine that …

Characteristics Of Proton Conducting Pva-Chitosan Polymer Blend Electrolytes., Mohd Fakhrul Zamani Abdul Kadir

Student Works (2010-2019)

The main focus of this present work is to build a good conducting solid polymer electrolyte (SPE) based on chitosan and poly(vinyl alcohol)(PVA) blend. Solution cast technique has been employed to produce sample films in this work. From the scanning electron micrographs (SEM) the surface morphology of the blend containing 40 wt.% chitosan and 60 wt.% PVA (C4P6) is homogenous and miscible in one and another. The C4P6 film is the most amorphous and is the best candidate for the polymer host in the electrolyte systems studied in the present work. Ammonium Nitrate (NH4NO3) is the doping salt that provides …

Thermo-Electrical And Mechanical Studies On Polymer-Organically Modified Montmorillonite Composite., Norhana Abdul Halim

Student Works (2010-2019)

The field of polymer-nanoclay composite has attracted a lot of attention in materials studies due to the dramatic improvement on polymers characteristics. For example mechanical and thermal properties, chemical resistance as well as the reduced gas permeability. However, structural changes and the mechanisms that may contribute to these improvements are not fully understood. In this work, the study on polymer nanoclay composite concentrates on the effects of OMON inclusion within different polymer matrix systems. The matrixes are a series of natural rubbers (Standard Malaysia Rubber – Latex grade (SMRL); Deproteinized Natural Rubber (DPNR) and Epoxidized Natural Rubber (ENR-50)), plasticized Polyvinyl …

Electrical And Structural Studies Of Polyacrylonitrile (Pan) Complexed With Inorganic Salts., Khairul Bahiyah Md Isa

Student Works (2010-2019)

In the present study, polymer electrolyte films composed of polyacrylonitrile (PAN) as a host polymer, ethylene carbonate (EC) as the plasticizer and lithium triflate (LiCF3SO3) and sodium triflate (NaCF3SO3) as dopant salts were prepared by the solution cast technique. Five systems of polymer electrolytes films have been prepared; these systems are the plasticized-PAN system i.e. PAN-EC system, two salted-PAN systems i.e. PAN-LiCF3SO3 and PAN-NaCF3SO3, and two plasticized-salted PAN systems i.e. PAN-EC-LiCF3SO3 and PAN-EC-NaCF3SO3. The pure PAN film was prepared as a reference. The ionic conductivity for each system is characterized using impedance spectroscopy. The room temperature conductivity of the pure …

Chameleon Coatings: Adaptive Surfaces To Reduce Friction And Wear In Extreme Environments, Christopher Muratore, Andrey A. Voevodin

Chemical and Materials Engineering Faculty Publications

Adaptive nanocomposite coating materials that automatically and reversibly adjust their surface composition and morphology via multiple mechanisms are a promising development for the reduction of friction and wear over broad ranges of ambient conditions encountered in aerospace applications, such as cycling of temperature and atmospheric composition. Materials selection for these composites is based on extensive study of interactions occurring between solid lubricants and their surroundings, especially with novel in situ surface characterization techniques used to identify adaptive behavior on size scales ranging from 10−10 to 10−4 m. Recent insights on operative solid-lubricant mechanisms and their dependency upon the ambient environment …

Effect Of Carbon Nanofiber-Matrix Adhesion On Polymeric Nanocomposite Properties—Part Ii, Khalid Lafdi, William Fox, Matthew Matzek, Emel Yildiz

Chemical and Materials Engineering Faculty Publications

A successful integration of two independent phases with good adhesion is imperative for effective translation of superior carbon nanofiber filler properties into a physically superior carbon nanocomposite. Carbon nanofibers were subjected to electrochemical oxidation in 0.1 M nitric acid for varying times.

The strength of adhesion between the nanofiber and an epoxy matrix was characterized by flexural strength and modulus. The surface functional groups formed and their concentration of nanofibers showed a dependence on the degree of oxidation. The addition of chemical functional groups on the nanofiber surface allows them to physically and chemically adhere to the continuous resin matrix. …